Search Documents

By Victor V. Nazimko

Multiple mining generates gob-interaction displacements. They redistribute stress m strata and obey laws of irreversibility thermodynamics. An irreversible state causes inhomogeneity of the stress distribution on the mass. A destressed zone develops along a working panel, and worked out panels are deprived of the destressing. The inhomogeneity is smoothed out during elapsed time.

Jan 1, 1996

By T. Tamagawa, N. S. Fu, I. Iwasaki, M. Kobayashi

A 3-stage fluidizing bed process of chlorination, selective oxidation and sulfur chloride conversion was tested for processing of a chalcopyrite concentrate. It was found that the use of excess oxygen was essential to a stable operation in the oxidation reactor. The oxygen-excess gas will inevitably cause the oxidation of the sulfide concentrate in the chlorination and sulfur chloride conversion reactors. A new flowsheet is proposed to separate the chlorination and the selective oxidation steps with separate flow paths of the fluidizing gases, thereby preventing the passage of oxygen-excess gas in the chlorination and sulfur chloride conversion reactors. The feasibility of the proposed flowsheet was demonstrated in a laboratory-scale fluidizing bed setup.

Jan 1, 2000

By Russell E. Griffin

Dielectric constants and dissipation factors were measured by the Bureau of Mines for 13 simulated lunar rocks over the 20-to 100-megahertz frequency range by means of the susceptance-variation method. Measurements were made at room temperature and normal atmospheric pressure. Results are presented and some comparison is made with data reported by others. The rocks used include a broad range of physical characteristics and chemical compositions from the large areas of volcanism in Oregon and northern California, and two nonvolcanic types. These rocks make up a suite of rock standards used by a group of laboratories engaged in lunar research. The data presented will add to the basic scientific and engineering knowledge needed to utilize extra-terrestrial mineral resources for support of future space missions.

Jan 1, 1974

By Sivilay Sayavong, David Puller, Julian Gatward, David Hard, Martin Stanley

"AbstractThe Thames Water Tideway Tunnels programme involves the upgrade of London’s combined sewer and storm water system. The first section is the Lee Tunnel between the Beckton Sewage Treatment Works (STW) and the Abbey Mills Pumping Station. This will intercept the overflows currently discharging to the River Lee and has the capacity to store and transfer 350,000m3 of storm water and sewage. The project required 4 shafts and a 6.9km 7.2m diameter tunnel. The shafts are some of the largest ever constructed in the UK, with diaphragm walls up to 98m deep and 1800mm thick. As a result of the innovative methods of diaphragm wall design and construction adopted the 4 very large and deep shafts were able to be excavated and completed safely, with minimal water ingress and with extremely high quality.MVB, a joint venture of Morgan Sindall, Vinci Construction Grands Projets and Bachy Soletanche are delivering the £635m contract with Thames Water’s Project Management Team in a collaborative manner under an NEC contract. Mott MacDonald, Morgan Sindall UnPS & Bachy Soletanche are acting as designers.Some of the important advances in diaphragm walling made included:??Diaphragm wall design to both EC2 & EC7 taking into considering the assessment of chalk stiffness, high hoop stresses, large multiple openings and non-axisymmetric loadings.??Formation of shafts as a faceted circle from a series of overlapping panels, with primary panels up to 7.2m wide demanding concrete volumes up to 1300m3 be poured in one go. Overlapping secondary single bite panels cut into the grade C50/60 concrete.??Excavation of the full geological stratigraphy of London making bentonite management complex.??Panel verticality of 1:300 required over the full depth. The results achieved this and in many cases exceeded expectations with some panels coming in at up to 1 in 800 with the majority at 1 in 400 to 1 in 500. The project is also the first in the Soletanche Bachy Group to take data from the ultrasonic drilling monitor used to check the verticalty in electronic format in order to create 3D CAD as-built drawings.??Each diaphragm wall panel was reinforced over its full depth. Up to 18 separate pieces of reinforcing cage had to be installed in primary panels. Cages underwent a full range of temporary works designs to check that lifting, splicing and placing could all be undertaken safely. Fibreglass was used in the tunnel portals in the shafts to ease breakthroughs."

Jan 1, 2014

By J E. Lynch

The Weda Bay nickel and cobalt laterite deposits on Halmahera Island, Republic of Indonesia were first drilled in May 1996 by Strand Minerals Pte Ltd (Strand). Subsequent exploration has delineated four large laterite provinces, parts of which have been diamond drilled to outline an indicated nickel resource of 59.9 Mt of 1.51 per cent Ni and 0.09 per cent Co within a total indicated and inferred resource of 117 Mt of 1.36 per cent Ni and 0.12 per cent Co. The project is held as a Seventh Generation Contract of Work (COW) by PT Weda Bay Nickel, which is jointly owned by Strand (90 per cent) and PT Aneka Tambang (ten per cent). Strand is a wholly owned subsidiary of Weda Bay Minerals Inc, a company listed on the Toronto and Alberta Stock Exchanges in Canada. Halmahera is located in the north-eastern part of the Indonesian archipelago at the convergent junction of three major plates and is a region of considerable tectonic and geological complexity. The western arms of Halmahera form a classic volcanic island arc while the central region and eastern arms contain ophiolite complexes and interlayered sediments. The extensive areas of laterite discovered at Weda Bay have developed over serpentinised harzburgites and dunites of pre-Cretaceous age. Weathering of these rocks has produced laterite profiles that are enriched in nickel and cobalt. There are three economically mineralised laterite types, namely limonites, ferruginous saprolites and saprolites and all are amenable to rapid pressure acid leaching with recoveries of 98 per cent nickel and 94 per cent cobalt in less than 20 minutes.

Jan 1, 1999

By Robert E. McIvor

The Functional Performance Equation for Ball Milling” was first presented in 1988. It now has been used successfully in more than a dozen mineral processing plants. This powerful, yet simple tool provides a new level of understanding of closed circuit grinding. It shows how grinding circuit efficiency is in reality comprised of two distinct efficiencies. It demonstrates how circuit production rate is related, collectively, to these two efficiencies, mill energy input, and the grindability of the ore. It links circuit performance to design and operating variables that can be manipulated, and creates an effective strategy for making plant improvements. This paper covers the derivation and industrial validation of this equation. As part of an engineering and management system that also incorporates suitable metrics and process control, other operators can now use this tool to make improvements and to manage the performance of their grinding operations with clarity and confidence.

Jan 1, 2005

By L. D. Johnson

On a project which is to develop a system to suppress coal dust explosions, a facility has been built and several devices tested. The facility is a 317-foot, 4.5-foot diameter shock tube and to date 53 tests have been carried out with methane-air and methane/coal dust-air as the explosive mixtures. Suppression of slowly propagating (up to 300 ft/sec) flame fronts has been successfully carried out on two tests using the dry chemical extinguishing agent Purple K. Delivery of the material directly into the flame front Seems to be required if effective suppression is to be accomplished.

Jan 1, 1972

Project Located in northwestern British Columbia 70km West of Cassiar Highway Galore Creek Project and Road Access Corridors Designated For Mineral Development in Stikine-Cassiar Land Resource Management Plan (LRMP)Approved in 2000Strong BC Government, local community and Tahltan First Nation Support for Project

May 1, 2006

By T. T. Tomimatsu

[This Bureau of Mines paper investigates explores, and analyses the Corporate structure dynamics and Rancid role to evaluate the economic health of the U.S. copper producers. It highlights the Corporate policy options and measures of corporate profitability and suggests that a competitive domestic copper industry will exist in the future. The study highlights the activities of 14 selected major copper-producing companies, including their subsidiaries o affiliates, that were responsible for more than 95 percent of the total U.S. production in each of the years since 1969. The selected firms are hot all primarily in the business of producing copper. Several of the large producers are classified by the financial institutions as integrated oil and gas enterprises.]

Jan 1, 1980

By Walter B. Lenhart

This paper is one of a series on milling methods and costs being. published by the Bureau of Mines. The milling practices and special problems relating to grinding, tailings disposal, and choice of a treatment process at the Cardinal mill are discussed. The property of the Cardinal Gold Mining Co. is about 18 miles southwest of the town of Bishop, Inyo County, Calif., at an altitude of approximately 8,500 feet. The camp has been designated Bishop Creek by the postal authorities. The property comprises 33 mining claims, including fractions and millsite in sections 19, 20, 29, and 30, T. 8 S., R. 31 E. These claims are located in a general way along the strike of a band of quartzite.

Jan 1, 1938

[ ]

Jan 1, 1981

By Meliton M. Garcia

The volume of gases produced in major and trace amounts following the detonation of two water gel and two emulsion explosives in a mine were determined. The volume .of the major gases (CO, CO2, NO, and NO2) was measured immediately following detonation, during the mucking operation, and following the removal of the muck. Tests to identify and quantify the gases produced in trace amounts were performed following the detonation only. The volume of each major gas per pound of explosive (ft /lb) ;ranged as follows: CO, 0.0424-0.3231; CO , 0.6819-1.5632; NO, 0.0129-0.1320; and NO2, 0.0019-0.1111.. An approximate average of 95% of the gases produced was found in the test chamber immediately following the detonation, while less that 2% was found in the chamber following removal of the muck. Benzene was the most significant compound found to occur in trace amounts. Scaling tests performed with a water gel and an emulsion explosive suggest that the volume of the gases per unit mass of explosive detonated diminishes as the amount of explosive per blast increases.

Jan 1, 1986

By M. Kanefsky

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties, but on the precise shape of the cross-correlation functions between the noise in-puts. By using two polairty difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 1, 1981

By R. Emmett Hughlett

The Bureau of Mines has developed a statistical approach to the laboratory evaluation of response bias and precision in gas detectors. The techniques described employ a computerized analysis and a new method of data presentation called composite graphing. The underlying theory, its practical application to the data, and the experimental equipment and procedure are described.

Jan 1, 1982

By William A. Beck

This report describes the loading and transportation practices employed at the zinc-lead mines of The Eagle-Picher Co., Jo Daviess County, Ill., and Lafayette County, Wis. The report also gives a brief history of the Illinois-Wisconsin zinc-lead district and the operations of the company in the area. The diesel-powered, rubber-tired loading and haulage equipment is described and illustrated from the operational point of view only, and an analysis is made of the materials-handling system without going into health and safety factors. The costs per ton of the various components of mechanical loading, underground haulage, underground crushing, and hoisting for fiscal year 1960 are tabulated.

Jan 1, 1964

By R. W. Stahl

Burning coal-mine refuse banks were surveyed in 15 States. The following characteristics were tabulated for 495 hanks: County; name, population, and distance of nearest town; size and status of bank; status and stage of fire; and topography. Ways of controlling fires were reviewed, the compacting and sealing method proving most satisfactory. Means for preventing refuse-bank fires by proper construction of banks are described.

Jan 1, 1964

By Robert P. Apa

Energy Incorporated has prepared this final report presenting the results obtained from the program for extracting alumina from anthracite culm along with the recovery of energy. This work has been accomplished under the auspices of the U.S. Bureau of Mines with technical coordination through the bureau's Reno, Nevada facility. The objective of this program was to develop a process to recover alumina and energy from Northeastern Pennsylvania anthracite mining waste. The program included Identification of sufficient resources to support a commercial facility, identification of the operating parameters which maximize alumina and energy recovery, the development of a conceptual process design, preparation of material and energy balance(s), and the performance of a system economical analysis. The program was conducted in three major phases. In the first phase the program concentrated on selecting several anthracite culm banks capable of supporting a commercial alumina producing facility. The chosen banks were then sampled and analyzed leading to the selection of two banks which were chosen far testing. The Harry E. and Eckley culm banks were the ones selected. Material from these banks was tested in Energy Incorporated?s Idaho Falls, Idaho testing facility. Parametric testing was accomplished in an eight-inch-diameter fluidized bed test facility. The test program consisted of twelve separate tests. After critical operating parameters were determined, the second phase started: process development in EI's 18-inch fluidized bed test facility. Three material and energy balance tests were completed in this facility. Following these tests a 72-hour demonstration test was performed. The data acquired from these tests were used in the last phase: the process conceptual design and economic analysis. The design basis was a commercial scale facility capable of producing 500,000 tons of alumina per year for 15 years. Based on the test program, It is technically feasible to build and operate such a plant today. The facility would produce, along with the alumina, 81.5 MWe of electricity for outside consumption. A preliminary rate of return indicates that the plant is not feasible with today's economic conditions. An increase in the market price of either the alumina or the electricity is required to provide an attractive rate of return for the facility.

Jan 1, 1982

By E. L. Garton

Michigan is becoming one of the important oil-producing States of the country. The amount of crude oil produced within its boundaries has increased from only 4,000 barrels in 19253/ to nearly 16 million barrels in 19935.4/ The Bureau of Mines method of crude-oil analysis and classification-indicates that the oils from the several producing fields are predominantly paraffin-intermediate-base, wax-bearing crudes. In general, they will yield 25 to 35 percent of highly paraffinic gasoline and about the t- me amount of kerosene and gas-oil combined, 7.2 to 15 percent of lubricating oil stock, and 20 percent of residuum with a carbon residue or about 6 to 7 percent. In addition, there appears to be some correlation between certain properties of the crude oils and both the geographical location and geological structure of the oil-producing areas within the State. These general conclusions are based on the analytical data presented in this report, which is one of a series of papers that record the general characteristics of crude oil from the many producing fields of the United States. This report discusses briefly the oil fields of Michigan and the characteristics of the crude oils produced from them. The analyses of 15 samples are given. These samples were obtained from 13 fields in 9 counties in the lower peninsula and represent crude oils produced from the Berea sandstone, Upper Traverse and Traverse limestones, and the

Jan 1, 1937

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By McHenry Mosier

The Bureau of Mines, United States Department of the Interior, has established a testing adit on the Government reservation at Mount Weather, Virginia, to facility to research on the fundamental tats of mining under actual metal-mining conditions. A number of sites in several Eastern States were investigated, out Mount Weather was selected because the rock seemed best suited for rock drilling and other mining tests and because the ground was already owned by the Federal Government, the site having been acquired in 1902 for use of the Weather Bureau. The testing edit has an advantage over en active metal mine for certain investigations because variable conditions affecting any particular research problem can be controlled and maintained in a fixed status, whereas in an operating mine this seldom is feasible. Operations were begin September 1935, with a crew of four laborers under a resident engineer. The laborers were recruited from, nearby farms, and. although they had no previous mining experience, they have developed into satisfactory miners.

Jan 1, 1939