Search Documents

By Y Chen, G Xu, B Albijanic

High concentrations of airborne coal particles is the main reason leading to health and safety hazards in underground coalmines. Water spray is one of the effective methods to suppress coal particles in mine sites, but the use of plain water is not effective enough to capture coal particles. By adding surfactants, coal wettability can be improved which will increase the coal dust suppression efficiency. In this study, a modified sink test was employed to evaluate coal wettability in the presence of two anionic surfactants: sodium dodecyl sulfate (SDS) and sodium dodecyl benzene sulfonate (SDBS). Sink rates were calculated by measuring sink weight over test time. Different surfactant concentrations (0.01 per cent, 0.05 per cent, 0.1 per cent, 0.2 per cent and 0.4 per cent) and two types of water (tap water and deionised water) were selected to investigate coal wettability over three size ranges (0–38, 53–75 and 75–90 µm). The results show that both SDS and SDBS surfactants can lower the water surface tension and improve coal wetting performance. Sink rates increased as the surfactant concentration increased, and surfactant solutions prepared by tap water performed better than deionised water in enhancing coal wettability. Also, coal wettability varied for different coal particle sizes; the smaller coal particles were, the worse the wettability they possessed.CITATION:Chen, Y, Xu, G, Wang, R and Albijanic, B, 2017. Study on coal wettability for dust suppression in the presence of surfactants by sink test, in Proceedings Australian Mine Vent Conference 2017, pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By A T. Job, M L. Edgar, P R. McAree

Characterising ores in-pit and in real-time presents a significant value opportunity for the mining industry. Hyperspectral imaging systems are proposed as an enabling technology to achieve this real-time characterisation. This paper considers the application of a hyperspectral imaging spectrometer mounted on a shovel. We define the performance requirements for such a spectrometer and associated subsystems during a typical dig-load cycle. The relatively high swing rotation speed of the shovel requires approximately video-rate exposure times to achieve good spatial resolution. We analyse a selection of components against these requirements and find that suitable commercial spectrometers, detectors and optics appear fit-for-purpose. Automated, real-time spectral classification systems are also available, with only relatively modest requirements for processing power. The paper argues that at near peak solar illumination, a system for field deployment at the required sensitivity is viable using only commercial off-the-shelf components.CITATION:Job, A T, Edgar, M L and McAree, P R, 2017. Real-time shovel-mounted coal or ore sensing, in Proceedings Iron Ore 2017, pp 397–406 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By R. Tamblyn

Vertically stirred media mills are a highly effective low-footprint solution for the ultrafine grinding of industrial minerals. This work investigates the effect of media density on flow patterns within the mill. Direct irradiation of a media particle leads to decay through positron emission, consequently forming two anti-parallel gamma rays, which allow for the real time tracking of particle position. Grinding media of the same size, but with a range of specific gravities are followed using this method, and the effect on the flow within the mill is revealed. The technique is seen to be an effective method to highlight the velocity profiles within the mill, as well as the zones where grinding is less efficient ? areas of relatively low velocity and high residence time. The changing media is seen to effect the overall flow patterns within the mill, having consequential effects on the efficiency of the grind.

Jan 1, 2009

A massive cobalt-containing pyrite orebody occurs in banded albite-quartz-biotite rocks at Thackaringa, some 30 km SW of Broken Hill. Because of the world-wide shortage of cobalt during the late 1970s, serious consideration was given to the development of a suitable flow-sheet to recover the cobalt from this ore. Details of a pressure leaching process in which more than 90 per cent of the cobalt is extracted from a pyrite concentrate are presented.

Jan 1, 1983

Brunswick Mine, one of the largest underground zinc mines in the world, is scheduled to close in 2010 after almost half a century of production. All mines eventually close; some suddenly as a result of unsustainable economic or technical conditions and others, as in our case, as a result of the depletion of the orebody. When the mine is the most significant employer and an economic driver in the region, it is key that the closure is handled in a planned, communicated, well-executed fashion. The following paper documents strategies, plans and activities that are currently taking place in order to ensure a seamless closure that satisfies all stakeholders including employees, management, regulatory bodies and the public. It is an important deliverable for the company that the good will, credibility and reputation that has been built up over the years is sustained throughout the closure process and beyond. A life of mine labour agreement with the unionised workforce, staff retention and recruiting programs, regulatory closure plans, communications and transition adjustment activities will be discussed. The use of a stage-gate style project management tool analysing the risks and key deliverables will be highlighted. It is hoped that the concepts and approaches discussed here may be of value to other operations that will be faced with closure, and its inherent challenges, in the not too distant future.

Jan 1, 2006

During the lifetime of an open pit mining project, each stage from exploration activities to exploitation and mine closure produces disturbances on the mining region. Mined land reclamation plans establish constructive solutions to rehabilitate the disturbed areas. Open pit mining as an effective method for exploitation of a wide range of orebodies especially for massive reserves of shallow metallic substances has exhaustive and harmful environmental effects on the mining project region. Nowadays, closure and reclamation stage in a mining project is emphatically enforced by the relevant environmental protection regulations in many countries. It is therefore obvious that closure and reclamation costs of an open pit mining project, as costs of other stages of project, must be estimated to enter the planning and design processes in open pit mining. Post-mining land use is the most important factor to recognise closure and reclamation costs. Thus, using a model to define optimal land use in planning phase of an open pit mining project is necessary in this regard. In this project a model was developed to define optimal land use regarding different sections of open pit mines such as pit(s), waste dump(s), tailing pond(s), roads, areas for onsite facilities and free land zones which are not mined. TOPSIS and PROMETHE techniques were applied to create the developed model. Lumber production was recognised as the optimal post-mining land use for the pit area of the case study in this project.

Dec 6, 2010

By Jerald E. Harris

"Often taken for granted, drill accuracy plays a major role in the relative success or failure of a blast.Expensive technological advances in equipment capabilities, drilling tools, communications, explosives, and timing can quickly be nullified by poor drilling."

Jan 1, 1999

By G. R. Adhikari

Step 4: Selection of explosives and initiation system Various types of explosives are manufactured in India and a wide choice is available among them that include nitroglycerin based explosives, slurries, emulsions, ANFO (ammonium nitrate mixed with fuel oil) and heavy ANFO. The choice is also available between cartridged and bulk loading systems. In Indian mines, much importance is unduly given to the cost of explosives alone which is not conducive to optimization of blast design parameters. The concept of energy per meter of blasthole and the way in which the total explosive energy is partitioned between shock and heave is not considered in the prevailing practices. Besides, very little efforts are made to objectively evaluate the performance of explosives for a given site condition. Tailoring explosives is limited to changing the density of the bulk explosives. Cartridged explosives are still being extensively used in large operations where bulk explosives should be the preferred choice.

Jan 1, 2002

By L. B. Berger

Studies showing the effect of mixing hot exhaust gases with the intake air of a four-stroke-cycle Diesel engine are described. The results indicate a marked increase in carbon monoxide in tip exhaust gases, a decrease in oxides of nitrogen, and no significant effect on aldehydes. The increase in carbon monoxide was greater at higher fuel-air ratios and was caused partly by the increase in fuel-air ratio end partly by the decrease in oxygen concentration resulting when exhaust has was added. The application of these results to the use of Diesel engines underground is considered.

Jan 1, 1940

By E. McCullough, D. Preece, M. Ortel

Geophysical explosive charges are used in mineral resource exploration. They are detonated subsurface and radiate sonic waves into ground monitors, which detect the vibration waves and their interaction with underlying geologic strata. Geophysicists perform computer analyses of the waves reflected from the strata to determine their depth and thickness (Strobel, Berger & Schaefer, 2012). The purpose of this research is to determine how the detonating explosive charge interacts with the adjacent ground and how the induced waves propagate through the surrounding medium. Furthermore, it is necessary to optimize the location of the initiation point within the charge. Establishing both the direction and intensity of the waves will allow geoscientists to refine and optimize geophysical studies that employ explosive charges.

Jan 1, 2013

By D. He

In China, the total reserves of vanadium, reported as V2O5, in stone coal is 118 Mt (130 million st). Recovering vanadium from such a large resource is very important to China?s vanadium industry. The technology now being used to recover vanadium from stone coal has the following two problems in the leaching process: a low recovery of vanadium and high acid consumption. To resolve these problems, a new leaching technology is proposed. The effects of factors such as H2SO4 concentration, liquid-solid ratio, temperature and time, and the types and additions of additives were studied. By adding 1.5% (by weight) CaF2 and leaching the roasted residue of stone coal with 5.4% (by weight) sulfuric acid at 90°C for 12 hours at a liquid-solid ratio of 2 mL/g, the leaching degree of vanadium reached 83.10%. This proposed leaching technology gives a feasible alternative for the processing of roasting residue of stone coal and can be applied in the comprehensive utilization of stone coal ores in China.

Jan 1, 2008

Upgrading of a Flow Sheet Selection PC Algorithm for Refractory Concentrates Treatment

Sep 13, 2010

By T. H. Eyde

Worldwide production of natural zeolites during 2001 was estimated to be about 3.5 Mt (3.85million st). Construction and agriculture continued to be the major consumers. Estimated production in North America during 2001, including the United States, Canada and Mexico, was about 40 kt (44,000 st). In the United States and Canada, the zeolitic tuffs are ground, extruded or modified for use as adsorbents, desiccants, ion-exchange media and carriers. In Mexico and the rest of the world, the zeolitic tuffs are cut into dimension stone that is used in construction. Zeolitic tuffs are usually composed of the minerals clinoptilolite, mordenite or both. They occur in a variety of colors and are easy to cut and shape. And they have low thermal conductivity. This construction application is classified with dimension stone rather than with chemical and agricultural uses.

Jan 1, 2002

By A. Kazemi, M. A. Ahmadi

Pressure tunnels are constructed nurously in related with powerhouse. In some cases, according to high internal water pressure, rock mass around tunnel can seldom suffer this pressure. So installation of concrete lining which interacts with rock mass and suffers parts of this pressure and transfers the rest of the pressure to the rock. In this paper hydromechanical interaction between rock and lining is investigated. With using empirical and numerical methods concrete lining for Symareh waterway is designed. Initial support of 10 cm reinforced shotcret with wire mesh and rock bolts pattern of 2.5*2.5 m with length of 4 m is suggested. By using FLAC package final lining with paying attention to axial force and momentum in reinforced concrete was designed. Reinforced concrete with 60 cm thickness and two rows of bars, 18 mm diameter and 20 cm spacing are designed. Also for preventing cracks in concrete which caused by the change of temperature and shrinkage, bars with 10 mm diameter and 25 cm spacing, and also bars with 8 mm diameter and 10 cm as minimum shear bars are suggested. Plusieurs galeries en pression se construisent en liaison avec les centrales électriques. Dans certaines galeries, suite à une haute pression interne de l'eau, le massif rocheux autour de la galerie ne peut pas supporter cette pression. L'installation d'une couche de béton a l'intérieur de la galerie donc réagit avec les roches et support d'une partie de cette pression et transfère le reste de la pression aux roches. Dans ce papier, l'interaction hydromécanique entre la roche et la couche en béton a été étudiée. En se basant sur les méthodes empiriques et numériques le système de support de galerie de passage d'eau de Saymareh a été conçu. Un soutènement initial d'une épaisseur de 10 cm de béton étant renforcé par un grill métallique et une maille de boulon (2.5 * 2.5 m) d'une longueur de 4 m a été proposé. En utilisant le logiciel de FlAC, la couche finale en béton selon les forces dans le béton a été conçue. Le béton renforcé d'une épaisseur de 60 cm et deux ranges d'armateurs (18 mm de diamètre) avec un intervalle de 20 cm a été conçu. De plus; pour éviter des fissures dans le béton suite au changement de la température et de l'extraction, des armateurs de 10 mm de diamètre et de 25 cm d'intervalle pour augmenter la résistance au sciesiement du béton ont été proposes Unter Druck stehende Tunnels werden hauptsaechlich im Zusammenhang mit Kraftwerken gebaut. In einigen Faellen, wo der Wasserdruck zu hoch ist, Kann selten die Felsenmasse diesen hoehen Druck allein aufnehwen. Deshalb werden sie mit Betonauskleidung versehen, die wegen guter Wechelwirkung mit der Felsenmasse einen Hauptanteil des Druckes aufnehmen Kann, wobei der Rest an die Felsenmesse weitergeleitet wird. In dieser Arbeit wird die hydromechanische Wechelwirkung zwischen der Gesteinmasse und der Auskleidung untersucht. Mit Hilfe empirischen und numerischen Verfahren sowie Kombination der beiden wurde eine Betonauskleidung fuer die Symareh Wasser Kannal koustruiert. Als erstes wurde ein 10Cm dicker armierter Beton mit einem Mashengitter von 2.5*2.5 sowie den gleichen Felsbolzenabstaenden und einer Laenge von 4 m vorgeschlagen. Mit Hilfe des FLAC Programms wurde die Hauptauskleidung unter Beruecksichtigung von Axialkraeften und Momenten im Stahlbeton koustruiert. Der 60 Cm dicke Stahlbeton wurde mit zwei Reihen von Stangen, 8 mm im Durchmesser und in Abstaenden von 20 Cm koustruiert. Ferner im Sinne der Vorbeugung gegen Rissen im Beton, die durch Temperatur aendeungen und Schrumpfungen bedingt sind, wurden Stangen mit 10 mm Durchmesser und 2.5 Cm Abstaenden zur Erhoehung vor Scherfestigkeit des Betons vorgeschlagen.

Jan 1, 2003

By M. Wiber, P. Nicoll

Rio Algom has embarked on a major programme of expansion with the goal of becoming one of the world’s top-performing base-metal mining and metals distribution companies. To assist the company and its operations in achieving its business objectives, we are implementing an environment, health and safety (EHS) management system, built to be compatible with the 14001 model. We recognize that a sustainable development approach for Rio Algom includes outstanding performance in EHS and community responsibility and is essential to earn acceptance within the communities where we operate or wish to locate; raise capital; obtain permits, and operate efficiently. We are committed to triple bottom line accountability, i.e. full consideration of environmental, social and economic concerns in our business decision making.

Jan 1, 2000

By P G. Hicks

The influence of feed size and pulp density on the specific rate ofbreakage of quartz was investigated. Plots of log fraction of feedremaining within the feed size interval against grinding time allowed the application of the first order grinding model to be examined. Substantial non-linearities were observed for all feed sizes due to environmental and material factors. For feed sizes above 1.3 mm, the specific rate of quartz breakage was higher with rod milling than ball milling, but below this size the reverse was true. Material that remained in the feed size interval after the initial grinding broke more slowly in subsequent grinding than the original feed material. Grinding media and time as well as feed size influenced the effects of pulp density on grinding. More dilute pulps (eg 50 per cent solids density by weight) were favoured for higher rates of breakage in rod milling but for ball milling, the optimum pulp density appeared to be 60 to 70 per cent solids by weight.

Jan 1, 1998

By J. P. H. Steele, T. Vincent, C. Debrunner, M. Whitehorn

For a variety of reasons, the need for automation of underground mining equipment is growing dramatically, e.g., improved safety and health, availability of labor, deeper mines, and desire for more focused excavation. While there has been tremendous progress made in this direction, much needs to be done to reach the holy grail of an autonomous mining machine. This paper reviews a number of technological developments and presents research and development needs for future development. A report on our current project for the Western Mining Resource Center at CSM is included.

Jan 1, 2000

By C. Dirscherl

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train, the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71 percent — as confirmed by real operational data from the Antapaccay Mine in Peru. It was the first plant worldwide to use gearless drives for both applications.The gearless principleThe principal idea behind a gearless drive system is to reduce the number of components and diversity of parts, especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material.In order to apply this principle of simplification, the components of a conventional drive system are examined. They consist of:• Driven equipment (mill, conveyor, slurry pump).• Components altering the rated speed (gearboxes, girth gear/pinion).• The electric motor.• Starting devices for the motor (VSD, CCV, LRS, clutch), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage.• Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation.• The electrical supply system (cables, switchgear, transformers, protection equipment)."

Jan 1, 2015

By Carl W. Kelley

PRODUCTION in the United States of carbon black has increased from 20 million pounds per year in 1920 to over 2 billion pounds in 1964 valued at $156 million, mostly for consumption by the rubber-tire industry, which uses over 90 percent of total production. Production of over 2 billion pounds in 1964 is a 7.8-percent increase over 1963 and is the first time furnace black production has topped 2 billion pounds. Although 1964 channel black production dropped 6 percent below 1963, carbon black produced by the furnace process, which ac-counted for 92 percent of total production, increased 9 percent to 2,053 million pounds. Total shipments during 1964 amounted to 2,245 mil-lion pounds, a 7 percent increase. This growth parallels the expansion of the automotive and petroleum industries. Along with this expansion have been many advances, both in methods of manufacture and in the quality and variety of blacks available to industry. There are several kinds of carbon black, thermal, channel, furnace, lamp, and oil blacks. Until recently, channel has been the important black in rubber compounding. Following the introduction of the synthetic GR-S, and more recently of "cold rubber," it has been found that certain furnace blacks with particle size larger than that of the standard channel black give superior reinforcement. A great advantage of furnace black is that its yield per unit of gas feedstock is higher than that of channel black. The 184-million-pound increase in domestic carbon black sales was partially offset by a 37-million-pound decrease in exports. Decrease in exports especially to Europe, is expected to continue. In Europe, as in the United States, the major end use for carbon black is in the manufacture of automobile and truck tires. Although the number of automobiles in Europe is predicted to grow by about 7.5 percent per year, compounded until 1975, the increased demand will be met by a 20 percent increase in existing capacity and by the new plants being built in Europe by U.S. companies. Also) aromatic oils for producing furnace blacks are plentiful now that western Europe's chemical industry is switching to a petroleum base.

Jan 1, 1965

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007