Search Documents

Gold was determined directly in eight different mill cyanide solutions, by atomic absorption spectroscopy in an acetylene-air flame. Some of the mill solutions were diluted with water to bring them into the most sensitive absorption region (5-50 p.p.m. Au) whereas those solutions with very low gold content «2 p.p.m.) were concentrated by evaporation.Calcium was complexed with ethylene diamine tetra-acetic acid (EDTA) to avoid the undesirable effect of a precipitate on atomization.When added to standard gold solutions, EDTA had no effect on absorption, nor did any of the impurities common in mill cyanide solutions.Known amounts of gold, ranging from 2 to 30 p.p.m., were added to mill solution'aliquots and recovered to within 100 ± 2·5 per cent. For duplicate determinations under normal worKing conditions, standard deviation was 1·32 p.p.m.Excellent agreement was found between atomic absorption gold values and accurate fire assay values.INTRODUCTIONAtomic absorption spectroscopy has been shown to offer a rapid and accurate method for the determination of trace amounts of a number of metal ions. In the field of primary metallurgy atomic adsorption has been used for routine determinations of lead, copper, silver, zinc, cadmium and iron in a variety of raw materials and intermediate products.The scope of atomic absorption spectroscopy was reviewed recently by Willis (1963).The noble metals silver, gold, platinum, rhodium and palladium were determined by atomic absorption from chloride solutions by Lockyer ·and Hames (1959). In their determination of gold down to 1 p.p.m., they found no interference from the noble metals, nor from considerable excess...

Jan 1, 1964

By D Caley

During the response to the Moura No 4 disaster, use was made of the New South Wales Mines Rescue Service’s ‘Mineshield’ inertisation equipment. The equipment had to be transported from Newcastle, approximately 1400 kms, and the liquid nitrogen a similar distance. The time taken, and therefore availability of the liquid nitrogen, became a significant problem. Operational issues were also experienced during use. Typically the liquid nitrogen is converted to a gas (vaporised) before being injected into the mine. However, as the propane gas tanker used for the vapourising unit was delayed, an attempt was made to inject the liquid nitrogen directly down uncased boreholes. This proved unsuccessful.Following the Moura No 4 disaster and the Moura No 2 disaster, recommendations were made relating to having inertisation capacity for the Queensland coal mining industry. Today the Queensland industry has multiple options available for inertisation, including the high-volume GAG and smaller volume units such as boilers and membrane separation units. Although it ultimately aided re-entry into Moura No 4, most likely due to the issues associated with supply to Central Queensland, liquid nitrogen has not found favour within the Queensland industry as an inertisation tool.Coregas has commissioned an air separation plant in Mackay, improving the availability of liquid nitrogen to Central Queensland. Based on the availability of this nitrogen, recent sealing operations at Kestrel have trialled using liquid nitrogen and associated vapourising units. This paper details the practical application and findings of using liquid nitrogen during routine longwall panel sealing.CITATION:Caley, D, 2017. Using liquid nitrogen for the inertisation of goafs, in Proceedings Australian Mine Vent Conference 2017, pp 35–40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By S. Heukelman

Zinc or, a zinc refinery in South Africa, uses oxygen enrichment of up to 26% O2 in its fluidizing air to increase concentrate-throughput in its fluidized bed roasters. The aim of the study is to determine whether O2 enrichment can be reduced by introducing micro-pelletized concentrate into the feed blend, while maintaining concentrate throughput rates and calcine quality. A laboratory scale fluidized roaster was used to determine the strength and oxidation kinetics of suitable micro-pellets. The strength of the pellets was determined by the extent of attrition during roasting. It was found that micro-pelletization decreases the fines in the feed to the roasters; the ?500 µm fraction decreased from 87% to 10%. The micro-pelletized particles do break down during roasting, which increases the -500 µm fraction to 31%. The general morphologies of the roasted particles are similar to those found by previous workers. Micro-pelletized concentrate particles require more time than non-pelletized concentrate particles to oxidize in the roasting step, although this is less than the mean residence time of the Zincor roasters. Roasting micro-pellets in O2-enriched fluidizing air increased the reaction rate.

Jan 1, 2011

By Eric S. Lindquist

High groundwater levels combined with variable soil and rock profiles present challenges to the design and construction of deep excavation support systems. Increasingly, secant piling techniques are the preferred technical solution for shoring in these cases. Recent developments in drilling equipment, tooling and procedures allow cost-effective construction of deep, overlapped pile systems to tight tolerances in extremely difficult ground conditions. This paper summarizes critical design considerations for secant pile shoring systems, detailing recent advances in installation procedures and verification techniques that allow secant piles to be used for an expanding range of project conditions. Technically- and commercially-viable secant pile shoring designs require that stringent drilling tolerances be achieved in order to successfully provide combined structural support and groundwater cutoff systems, particularly for unreinforced circular secant pile shafts acting in ring compression. Modern drill rigs and tooling can advance fully cased shafts in geotechnical conditions which range from cohesionless soils below the groundwater table to hard rock, within a single drillhole. Down-hole instrumentation provides verification that tolerance requirements are met and allow secant pile shoring to be used at sites previously considered unacceptably risky. In California, secant pile shoring systems are being used for excavation depths of over 100 ft (30 m) on projects with challenging site conditions. Two case studies are presented detailing severe geotechnical conditions and excavation depths which represent the regional state of practice in secant piled excavation support. These projects provide real world examples of the design, construction and construction verification techniques that permit secant pile shoring to be used in more demanding geotechnical conditions and to greater depths than ever before.

Jan 1, 2011

Owing to improvements in computer capacity, it is now possible to undertake fully coupled or partially coupled, three-dimensional (3D) hydromechanical Finite Element (FE) simulation of mines, including explicit representations of large numbers of discontinuities. The analysis requires fewer assumptions than uncoupled analysis or two-dimensional (2D) analysis, but may require a change in how hydrological data is collected. The way hydrological data is incorporated in stability assessment and the approach to uncertainty in hydrological information also requires discussion. The current procedures for this type of analysis are discussed, along with some practical difficulties and teachings from early applications. A work flow for integration of 3D hydromechanical modelling with pit planning and some considerations for the management of uncertain data are also proposed.

May 1, 2010

By S Robotham, P C. Stewart, K Maher

A data science based dilution study was conducted to identify the causes of dilution at South32’s Cannington Mine (Cannington), a large open stoping operation. In terms of industry benchmarks for unplanned dilution, Cannington is already performing very well, and so opportunities for improvement are more difficult to identify. The study is based upon back analysis of nearly 150 case studies from the mines reconciliation database, and has quantified the relative effect and significance levels for the following dilution parameters; time until paste filling, faulting and cable bolt reinforcement. Specifically, significant contributions were associated with faults and stope open duration. Quantifying the effect of faults on stability graph accuracy enabled a site specific adjustment to improve the predictive ability of the Cannington stability graph (unstable stope specificity improved from 63 per cent to 74 per cent). Despite Cannington’s already high levels of stope performance compared to industry benchmarks, data science methods have identified a complex interaction between identified dilution factors (ie stope open duration, presence of faults and cablebolting). Specifically, a third order Factorial ANOVA (Analysis of Variance) provided evidence that stope open duration reduces the effectiveness of cable bolts in faulted ground (average dilution = 2.1 m, p-value = 0.13). These results are consistent with site observations of a relationship between the stope open duration and the extent of failure when unravelling on a fault, even when cables are present.CITATION:Maher, K, Stewart, P C and Robotham, S, 2016. A data science approach to identifying and quantifying causes of dilution at Cannington Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 491–500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

As metal prices fluctuated over the years, so too have the fortunes of many of those mining in Canada?s Yukon province. With a rich mining history that dates back to the Klondike gold rush of 1896 to 1898 and continues to thrive today, Yukon has experienced several ?boom-and-bust? cycles. However, during the world?s most recent mining ?bust? Yukon has held strong and has re-mained one of the world?s hottest destinations for mineral exploration. In fact, the area even exceeded forecasts in 2009, more than doubling last year. And the near-future looks just as bright.

Jan 1, 2010

By Jasper L. Stuckey

PYROPHYLLITE, first identified as soapstone,' later as agalmatolite,2 and finally as pyrophyl-lite, has been known to occur in North Carolina for more than 130 years and has been produced intermittently in commercial amounts for the past 100 years. Pyrophyllite mining, however, has become a major industry in North Carolina only during the past 25 years. North Carolina and California are the chief producing states. Current annual production averages 125,000 tons, of which slightly more than 90 pct comes from North Carolina. Distribution and Geologic Setting: All known pyrophyllite deposits in North Carolina are associated with rocks of the Carolina Slate Belt,' which is composed of a vast series of metamorphosed volcanic and sedimentary materials, occurring as two zones extending in a northeast-southwest direction across the state. The larger of these zones, lying in the central Piedmont region, varies from 8 to 50 miles wide. The smaller zone lies along the eastern edge of the Piedmont region and is partly covered by coastal plain sediments. The rocks in both zones consist of a great volcanic-sedimentary series, composed of air-laid and water-laid tuffs and breccias, lava flows, and slates. On the basis of composition, they may be classed into three groups: 1) tuffs, breccias, and lava flows of acid or rhyolitic composition; 2) tuffs, breccias, and lava flows of a basic or andesitic composition; and 3) water-laid slates composed of fine grained materials derived chiefly from the acid tuffs and breccias and

Jan 1, 1959

The mining industry worldwide is currently facing a significant restructuring process. In most underground mines, widespread mechanization of the mining processes increases production while reducing staff numbers. At the same time, mining depths as well as the lateral spread of the mine workings are increasing. This ever-changing mining environment requires sophisticated solutions for the design and operation of underground mines. In fact, a reduced number of mining engineers is taking responsibility for everincreasing mine operations. This applies not only to the excavation of the minerals, but also to all other aspects of the mining operation, including health and safety, disaster management, and mine rescue organization. Most mining engineering graduates entering the industry lack experience in mine emergency management. Young engineer trainees must learn mine emergency management and rescue work in addition to their normal training experience on the job. Often, and unfortunately, emergency and rescue training at different mining companies is not carried out to the highest level and standard and with the best possible training outcomes. The tasks and challenges a young engineer faces while being trained in a new position do not leave much room for additional training in mine rescue and emergency management. At the same time, experienced, ?old hands? are retiring and cannot easily be replaced due to limited graduation numbers. Strategies are being developed at mining universities worldwide to train mining engineering students in handling mine emergency situations and to provide hands-on experience for managing potential accident and disaster scenarios underground. Two of these strategies, from the USA and from Central Europe, are presented in this paper. These specific strategies have to be seen under special consideration of the local and regional boundary conditions, but might serve as case studies for mining schools and universities in other countries.

Jan 1, 2014

By G. F. Vander Voort

The accident at Unit No. 2 of the Three Mile Island nuclear reactor (TMI-2) on 28 March 1979 was the worst nuclear accident in US history and crippled the nuclear industry. An international Vessel Investigation Project was formed to assess the integrity of the vessel. However, it was not possible to remove specimens from the lower head until January?March 1990. Fourteen of the fifteen specimens removed by electrical discharge machining were from under the debris pile that accumulated on the lower head due to melting of approximately 19 000 kg (45%) of the core. Specimens were previously cut from the lower head of a cancelled reactor of very similar size and design destined for Midland, Michigan. These specimens were subjected to controlled heating cycles with peak temperatures from 800°C to 1100°C for periods of 1 to 100 minutes. The initial study qualitatively compared the structures in the 15 specimens from TMI-2 to the control specimens from the Midland lower head. The writer used the same specimens and employed microindentation hardness traverses, electron microprobe analysis, and selective etching followed by quantitative metallography (by image analysis) to obtain a far more detailed description of the thermal exposure experienced.

Jan 1, 2013

By N. Henderson, J. Weyer, J. F. Brune

"The mining industry worldwide is currently facing a significant restructuring process. In most underground mines, widespread mechanization of the mining processes increases production while reducing staff numbers. At the same time, mining depths as well as the lateral spread of the mine workings are increasing. This ever-changing mining environment requires sophisticated solutions for the design and operation of underground mines. In fact, a reduced number of mining engineers is taking responsibility for everincreasing mine operations. This applies not only to the excavation of the minerals, but also to all other aspects of the mining operation, including health and safety, disaster management, and mine rescue organization.Most mining engineering graduates entering the industry lack experience in mine emergency management. Young engineer trainees must learn mine emergency management and rescue work in addition to their normal training experience on the job. Often, and unfortunately, emergency and rescue training at different mining companies is not carried out to the highest level and standard and with the best possible training outcomes. The tasks and challenges a young engineer faces while being trained in a new position do not leave much room for additional training in mine rescue and emergency management. At the same time, experienced, ’old hands’ are retiring and cannot easily be replaced due to limited graduation numbers.Strategies are being developed at mining universities worldwide to train mining engineering students in handling mine emergency situations and to provide hands-on experience for managing potential accident and disaster scenarios underground. Two of these strategies, from the USA and from Central Europe, are presented in this paper. These specific strategies have to be seen under special consideration of the local and regional boundary conditions, but might serve as case studies for mining schools and universities in other countries."

Jan 1, 2014

By R. J. Balfour, T. L. Papucciyan

"INTRODUCTIONCapital Cost considerations are basic to feasibility in the achievement of success for Mineral Processing Projects as much as or more than in many other industries. Capital cost is an important factor ae it 1R the unit of measurement for process engineering economic decisions. As a result of ever increasing complexity, alternatives of process and remoteness of site, there is an ever increasing emphasis on accurate estimating and the attendant cost control systems in the international market of today for the Mineral Industry where initial plant costs are becoming a more important factor than operating costs. An undervaluation means trouble ahead. An over-cautious assessment may bring an unnecessary abandonment of a project. Consequently, the ultimate cost must be predicted early and accurately and must be controlled to this parameter during the design and construction phases. Cost Est!~ mating is one of a variety of project management tools used to assist in planning and achieving the optimum balance between Quality, Cost and Time, the eternal triangle of evaluation, namely obtaining a project of acceptable quality at minimum cost and on time. In order to attain these established objectives, proper planning, organizing, coordinating, monitoring, adjusting and controlling the design, procurement and construction elements of the project are essential.This project management approach based upon the principle of a Task Force under single management, comprising a complete service organization, requires a substantial number of qualified individuals specialized in their own field and capable of working together as a team to perform their various functions effectively. The Task Force is supported by their chiefs of discipline and performs in accordance with established procedures and standards under the leadership of a Project Manager.General Engineering Company Limited with the backing of the full resources of Surveyer, Nenniger & Chenevert and its total staff of approximately 1,0009 offers the complete project management service to the Mineral Processing Industry of North America and the rest of the world. As mine sites become more remote and difficult of access, the need for an experienced team of specialists who work under the Task Force principle, with well established standards and procedures becomes even more important. Our long history of successful pro1ecta in this field has been our training ground for the fulfillment of this need."

Jan 1, 1972

By G J. Corbett, T M. Leach

Approximately 42 t of mercury were produced from Puhipuhi from the late nineteenth century until the end of World War II, with no significant gold or silver production. Sinter, eruption breccias and veins, mined for mercury at Puhipuhi and essentially barren of gold, are inferred in many geological models to represent the surficial levels of adularia-sericite style low sulfidation gold-silver systems. These systems may contain economic gold-silver mineralisation at depth. Conceptual geological models have been employed at Puhipuhi in the search for buried gold mineralisation. Homestake Mining utilised a McLaughlin model for exploration from 1982 to 1987, targeting mainly the vicinity of the sinter deposits. From 1987 to 1989 BHP sought deeper structurally controlled gold mineralisation within the basement greywackes, utilising models derived from studies of Round Mountain, USA and Hishikari, Japan. Macraes Mining Company Limited have accessed the previous work and applied a conceptual geological which invokes a north-south structural control for the emplacement of high-level felsic intrusions at depth. Dextral movement on these structures associated with oblique convergence facilitated the formation of a pull-apart basin in which lacustrine sediments overlie basement greywackes and are in tum overlain by Pliocene basalts. Continued activation of the NS structures created a series of inferred NE-trending dilational structures, which are targeted as fluid upflow centres for the surficial outflows. Upflows occur as eruption breccias (e.g., Plumduff) and outflow as silica sinters (eg Mt Mitchell, Williams) which are also partly obscured by the basalt cover. Argillic alteration and mercury mineralisation occur at elevated crustal levels (eg Puhipuhi mine). Modelling from structure and alteration zonations have targeted a fluid upflow in the vicinity of Bush Hill, which was not accessed by previous workers. This target was subsequently supported by surface geology and multi-element soil geochemistry.

Jan 1, 1997

By L. F. Ruppert, W. D. Watson, S. J. Tewalt, L. J. Bragg

The U.S. Geological Survey recently completed a digital coal resource assessment model of the Upper Pennsylvanian Pittsburgh coal bed which indicates that of the original 34 billion short tons [31 billion tonnes] of coal, 16 billion short tons [14 billion tonnes] remain after subtracting mined-out coal. When technical, environmental, and social restrictions are applied to the remaining Pittsburgh coal model, only12 billion short tons [11 billion tonnes] are available for mining. Our assessment models estimate that up to 0.61 billion short tons [0.55 billion tonnes], 2.7billion short tons [2.4 billion tonnes], and 8.5 billion short tons [7.7 billion tonnes] could be available for surface mining, continuous mining, and longwall mining, respectively. This analysis is an example of a second-generation regional coal availability study designed to model recoverability characteristics for all the major coal beds in the U.S.

Jan 1, 2000

By D Brouwer, P Wild, B Belle

Due to the steep geo-thermal gradient in Bowen Basin area, as underground coalmines reach increased depths of extraction, the Bulk Air Cooling (BAC) requirements will increase as opposed to cooling the workplace using the ventilation means alone. One such mine has already been using a 4 MW surface BAC plant for the last six years to manage the working temperatures with reduced cooling efficiency as the mine expands. Due to the horizontal nature of the longwall mine layout, distances from the working face to intake shafts are rapidly expanding to over 6 km as opposed to the vertical mine layout of a hard rock mine. To improve the positional cooling efficiency, reduced panel pressure differentials, improved rib emission gas management, and intake dust management, small diameter intake shafts were located on the inbye end of production panels and halfway up the development panels with localised mobile small BAC plants. This paper summarises the results of extensive underground data of this innovative cooling concept for development and retreating longwall face heat management compared to a larger remote BAC plant.CITATION:Belle, B, Brouwer, D and Wild, P, 2017. The use of mid-panel ventilation shafts to improve positional cooling efficiency in a Bowen Basin longwall mine – a case study, in Proceedings Australian Mine Vent Conference 2017, pp 217–224 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017

By R. S. Bowman, G. S. Austin, J. M. Barker, P. S. Freeman

The physical, chemical and mineralogic characteristics of zeolites allow commercially important applications. While adoption of zeolite technology is slow in the United States compared to other regions of the world, continued testing and research has shown a wide range of uses for these minerals. They are important catalysts in petroleum refining, molecular sieves able to separate gases, and chemically inert carriers of reactants. The zeolite clinoptilolite produced by St. Cloud Mining Company (clino) (SC) is used in animal hygiene and animal feed, especially concentrated animal feeding operations (CAFOs), horticulture, water treatment, floor dry, aquariums, air and other filters, and odour control. Clino can remove cations from solution, and surface-modified zeolite (SMZ) is a sorbent for the removal of anions and neutral organics from water. Specific clino applications are: control of chemical pollution in groundwater, removal of organic compounds from oil field waters, and elimination of pathogens from sewage effluent. Combining the sorption capabilities of SMZ with chemical or biological transformations can yield complete removal of toxic materials from contaminated water. Continued development and marketing of zeolite products will be a growth market far into the future. The CAFO market for zeolites is the most significant growth area in the United States over the next few years. SMZ, currently less than 1% of St. Cloud sales, will continue to gain market penetration for many years.

Jan 1, 2004

By A Hollweg, K H. Esbensen, M Lischka

Two new splitter designs for intercepting moving streams of matter are presented, the variable cross-stream splitter (vCSS) and the rotary stream splitter (RSS), which are intended for implementation in a fully automated modus. The vCSS facilitates obtaining up to three subsamples with different splitting ratios from automated laboratory flow paths, while the RSS divides the intercepted sample into 16 equal analytical aliquots. The splitters can process a wide range of dry, granular and free-flowing materials (<5 mm). The required weight for each subsample can be set without mechanical adjustments in the case of the vCSS. Typical applications are subsampling/splitting for X-ray fluorescence pelletisation (or fused beads) or splitting for average shift composite sampling or grain size analysis. The vCSS combines the advantages of riffle splitting (three user-defined subsample masses) with miniature bed blending and can accept up to 15 kg in total incoming sample mass. In practice, the automated vCSS can deal with unlimited ingoing mass fluxes, while the RSS is designed to operate at a user-defined fixed subsampling rate (1/16th in the tested version). Both splitters have the potential to be optimised and evaluated according to an application/user-defined total sampling error (TSE) + total analytical error (TAE) threshold. Both splitters were tested under adverse conditions and with compositions involving three components with properties representing typical mass fluxes and components concentrations in industrial and technological systems: phosphate concentrate 89.00 per cent (<500 µm), slag ten per cent (>2 mm) and glass spheres one per cent (750–1000 µm). The slag particles vary widely in particle shape, aspect ratio and surface roughness, while the glass spheres are extremely prone to bouncing and segregation (spillage). This test system is extremely difficult to split and thus constitutes a realistic worst-case scenario. While the vCSS does not comply strictly with Theory of Sampling demands for correctness, both splitters may well be able to deliver fit-for-purpose representative results if/when tested properly. Average relative mass deviations ranged from 1.89 per cent for phosphate concentrate (relative standard deviations of 20-fold repeated splitting) to 4.72 per cent for glass spheres and 13.04 per cent for slag. For the RSS, the average replication experiment splitting variation was 2.89 per cent for phosphate concentrate, 4.82 per cent for glass spheres and 11.1 per cent for slag. Both new automated online splitters would therefore appear to be able to be tuned to fit-for-purpose representivity (defined here as maximum relative reproducibility <5 per cent) for many non-extreme materials; however, it is always imperative to test every new type/class of material empirically. There is a wide commercial potential for important materials and commodities sectors, including food, feed, drugs (pharmaceutical), secondary raw materials, recyclates, agricultural products and seeds.CITATION:Lischka, M, Hollweg, A and Esbensen, K H, 2017. New online/atline splitter designs for laboratory automation – feasibility results, in Proceedings Eighth World Conference on Sampling and Blending , pp 159–166 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

The modelling of lithological domains is a critical step in mineral resource and reserve evaluation. Deterministic models rely on an interpretation of the available drill hole data and expert knowledge, but do not account for the uncertainty in the spatial extent of the lithological domains. Instead, probabilistic models based on conditional simulation can be used to map the probabilities of occurrence of the domains within the deposit, which reflect the uncertainty in their presence or absence at unsampled locations. The mineral grade model is then obtained by weighting the predicted grades associated with each lithological domain by the probability of occurrence of this domain. Such an approach accounts for the continuity of the grades proper to each lithological domain and for the uncertainty in the spatial extent of these domains within the deposit. An application to a porphyry copper deposit is presented. Keywords: spatial uncertainty; plurigaussian simulation; geological control; kriging; geostatistics.

Jan 1, 2007

By M. E. Rossi, J. E. Camacho

"Geostatistical conditional simulations are becoming increasingly popular as tools that provide models of uncertainty at different stages of a mining project. They have been used as grade control tools in daily operations to assess the uncertainty of mineable reserves at the project’s feasibility stage, and to assess mineralization potential in certain settings. Other applications include assessment of recoverable reserves, resource and reserve classification, and drill hole spacing optimization studies. All large-scale applications of conditional simulations intend to benefit from the correct (or accurate) characterization of uncertainty, adequately describing the variability observed from the data and its effect on the final objective.The objective of this paper is to compare the ad-hoc uncertainty model provided by a traditional classification scheme with the probability intervals resulting from a conditional simulation model. It is argued that the uncertainty model derived from the use of classification schemes is of little practical use to the mining company or operation. The paper emphasizes differences in uncertainty based on the size of the mining unit considered, the extraction method, and local geological differences. Most importantly, it discusses confidence intervals for these mining units, as compared to the relative precision envisioned by a typical classification scheme.The application described in this paper is taken from a medium-sized Cu open pit and underground mine in northern Chile, and demonstrates the impact of several variables on the resulting conditional simulation models. It also compares a more traditional resource classification scheme applied, and the wide difference in local confidence intervals for each mining unit."

Jan 1, 2004

By D. D. Munro

Finsch Mine is a kimberlite diamond mine located at Lime Acres in the Northern Cape Province of South Africa. The mine was founded in 1961 and started surface mining in 1964. Underground production commenced in 1990 using a modified blast-hole open stoping method for the mining of Blocks 1, 2 and 3. Block 4 is currently being mined as a block cave. The process of identifying and optimizing a method to mine the Block 5 orebody started in 1991, and in 2006 incline caving was identified as being technically feasible. This paper aims to document the process employed in developing this method by the Block 5 prefeasibility team as well as discuss the technical challenges encountered during this process. The paper commences with a history of Finsch Mine and highlights the complex geology and threat of sidewall failure that prompted the decision to use block caving as the mining method for Block 4. A literature study of mines that implemented mining methods upon which the incline cave was conceptualized is then presented. These practices were then used to form the basis for the designs on which the initial geotechnical modelling was done and built upon through an iterative process of modelling and design changes. The ventilation of the mining area, initial productivity simulation results, and the applicability of automation and comminution processes in the incline cave are also presented. The paper concludes with an investigation into some of the challenges of the mining method, and shows that that incline caving is a technical option available for further investigation in determining the optimal mining method to be employed at Block 5, Finsch Diamond Mine. Keywords massive mining, incline caving, geotechnical modelling.

Jul 1, 2013