Search Documents

By F. P. Hassani, Jacque Ouellet, M. Hossein

A laboratory investigation was undertaken to evaluate the effectiveness of different binding agents in a paste backfilling operation suitable to be used in a sulphide-rich environment. Different combinations of Portland cement and fly ash type C as well as ferrous slag were used as the binding agents. The unconfined compressive strength of the samples was measured for extended curing periods. The results indicate that the addition of 3% slag in the binding agent mix could produce strengths up to 0.5 MPa in the samples under investigation. For higher binding contents, the addition of Portland cement will lead to higher availability of calcium hydroxide and calcium aluminate, which are susceptible to deterioration from the phenomenon known as sulphate attack. Using slag, on the other hand, will reduce the permeability, availability of calcium hydroxide, and dilute the calcium aluminate ions reducing the susceptibility of the samples to sulphate attack. However, gypsum will form which could have the same detrimental effect on the strength of the treated matrix. Therefore, special attention must be given to the content and properties of agents used to activate the pozzolanic properties of the slag.

Jan 1, 2001

By Kimberly Conner-Mills

Due to increasingly stringent worldwide environmental regulations for gaseous, aqueous and solid waste emissions, conventional smelting technology cannot effectively process arsenic containing materials. Many globally significant copper properties have copper sulfide mineralogy that has a high arsenic content present as enargite with significant contained precious metals. As global copper, silver and gold demand increases while significant world resources decrease, treatment of sulfide orebodies with enargite is becoming increasingly important. Methods to selectively dissolve and fix arsenic, leaving behind clean copper and precious metals-bearing concentrates could effectively treat these ores.

By Artur Skoczylas, Paweł Stefaniak, Sergii Anufriiev, Wioletta Koperska, Maria Stachowiak

In many underground mines the excavated ore is produced during the blasting process. Drilling machines that are used to drill the blastholes, where later the explosives will be mounted, are crucial for this task. In order to optimize the currently used techniques, great emphasis is placed on increasing the efficiency and safety of blasthole drilling operations. The natural consequence is the development of monitoring systems and algorithms for processing operational and historical data. In this article, we present the result of the analysis of drilling data carried out as part of the IlluMINEation project. The paper proposes an algorithm for work cycle detection for drilling machines, together with the estimation of general operating parameters and diagnosing the drilling process on the basis of long-term data. Based on the available data, selected components of the drilling cycles have been indicated. Several approaches based on the parameters of the defined cycles are proposed. These approaches can be used in the future to create a full-fledged system for examining the effectiveness and safety of mining drilling rigs.

Jun 25, 2023

By Andrew Thallisson de Souza

Os aços inoxidáveis ABNT da série 300 são ligas austeníticas Fe-C(< 0,08%) - Cr(18 a 20%) - Ni(8 a 10%) são muito aplicados, pois apresentam alta estampabilidade, alta soldabilidade, boa resistência à corrosão uniforme em vários meios corrosivos, no entanto, sofrem corrosão localizada (pites, corrosão sob tensão, fresta e corrosão intergranular). Os aços inoxidáveis da família UNS S32304, têm 23%Cr e 4%Ni. Por terem teor de carbono inferior a 300ppm (0,03% em massa) são resistentes à corrosão intergranular, sofrem pites e corrosão sob tensão (CST). Devido ao alto teor de cromo, o aço UNS 32304 apresenta boa resistência à corrosão uniforme, sendo que na corrosão por pites o mesmo apresenta um comportamento melhor que os aços ABNT 304 (sem Mo) e ABNT 316 (com Mo), de acordo com o Número Equivalente de Resistência ao Pite (PREN). O PREN dos aços UNS 322304 é 26, e para os aços ABNT 304 e 316 são 18 e 25, respectivamente. Este trabalho caracterizou os diferentes aços inoxidáveis química, metalográfica e eletroquimicamente em meios contendo íons cloretos. A partir de ensaios de caracterização eletroquímica, por polarização potenciodinâmica, verificou-se que o aço ABNT 304 apresentou potencial de pite inferior aos aços ABNT 316 e o UNS 32304, em soluções aquosas contendo 3,5% (massa) de NaCl. Verificou-se que estes aços sofreram CST empregando-se ensaios de deformação (corpo de prova em U) e carga constante (corpo de prova de tração liso) nos eletrodos em soluções aquosas contendo 42% (massa) de MgCl2 na temperatura de aproximadamente 143°C. Salienta-se que o comportamento em CST do aço ABNT 304 foi inferior aos demais. As amostras ensaiadas foram caracterizadas fratograficamente (macro e microfratograficamente - empregando-se microscopia eletrônica de varredura). Os corpos de prova que sofreram CST apresentaram facetas de clivagem e “marcas de rios”, características da fratura frágil.

Aug 17, 2017

By Tiago Ribeiro Costa

A Praxair é uma das três maiores empresas de gases industriais do mundo, com atuação em mais de 40 países e fortemente atuante na indústria siderúrgica. A Praxair possui experiência para fornecer produtos e serviços para todos os tipos de siderúrgica. Diversas tecnologias desenvolvidas pela Empresa, como o CoJet® (sistema para injeção de jato coerente de oxigênio em fornos elétricos e conversores), Slag Splashing (espalhamento de escória nas paredes de conversores, aumentando a vida útil dos refratários), AOD (processo para produção de aços especiais) e outros, encontram-se em operação comercial atualmente em diferentes partes do mundo. No Brasil, a PRAXAIR é a controladora da White Martins, maior empresa de gases industriais da América do Sul, presente em nove países do continente. Seu portfólio inclui gases atmosféricos, produção de gás carbônico, acetileno, hidrogênio, gases especiais e medicinais, misturas para soldagem, cilindros de aço sem costura, equipamentos para aplicação, transporte e armazenamento de gases. A empresa também opera uma unidade para liquefação de gás natural. Além de tecnologias e processos, a White Martins também pode fornecer soluções e equipamentos para medição, controle e injeção de gases, atendendo às rígidas normas de segurança e padrões de qualidade. O Objetivo deste trabalho é apresentar e discutir sobre a solução para o fornecimento de mistura para atmosfera de fornos de tratamento térmico através de um painel misturador de gases hidrogênio e nitrogênio. Será discutida a operação do equipamento e abordadas às características construtivas.

Jul 31, 2018

By Ramon Silveira Assis Barros

Este trabalho foi realizado com o objetivo de se investigar o comportamento do aço inoxidável duplex UNS S32304 em meios contendo íons cloreto. Para tanto, foram realizados ensaios CST com carga e deformação constantes usando meios com concentrações distintas de cloreto de magnésio (MgCl2), em ebulição. Foram realizados também análises química, metalográfica e eletroquímica do material. Após os ensaios de CST, foi constatada a suscetibilidade à CST deste material, além da influência da concentração de íons cloreto na solução. Essa constatação foi reforçada após a análise microfractográfica dos corpos de prova ensaiados. A análise eletroquímica do material revelou a evolução de pites em potencial de, aproximadamente, 400mVECS.

Jan 16, 2018

By Gil Ribeiro Vilela Neto

Na busca por se tornar cada vez mais sustentável, a indústria mineral vem recorrendo às soluções tecnológicas que minimizem o impacto ambiental gerado pela disposição dos rejeitos resultantes dos processos de beneficiamento de minérios. Neste cenário, umas das soluções é a aplicação de tecnologias de separação sólido-líquido com o objetivo de maximizar o desaguamento dos rejeitos e, consequentemente, diminuir o volume ocupado por eles quando dispostos e aumentar a recirculação de água. Este trabalho tem como objetivo, determinar a influência da concentração de sólidos em polpas de rejeitos denominados de “lamas” no desempenho do espessamento e a determinação da concentração de sólidos ótima para atingir o melhor desempenho do espessador.

Aug 16, 2017

By Charles Fettke

IN 1914, the officials of the Brundred Oil Corpn., faced with the problem of introducing new methods to increase production in the old and nearly depleted pools of Venango County, became interested in the Smith-Dunn (Marietta) process which was at that time being tried out in southeastern Ohio and which was already yielding very encouraging results. A license to use the process in Pennsylvania was secured from the owners of the patents. These patents were later declared invalid. The method was first used in Pennsylvania on a property consisting of about 434 acres, of which 300 are productive, at Hamilton Corners, 15 miles northeast of Oil City, in Cherry Tree and Oakland Townships, Venango County. The producing horizon is the First Sand of the Venango Group. A small oil pool was opened up in this vicinity in 1904. By July, 1916, when the compressed air was first introduced to restore pressure, the production had dropped to a point where it was no longer possible to continue profitable operation. From that time until March, 1927, over 100,000 bbl. of oil have been recovered from the tract. The property is being operated at present by the Brundred Oil Corpn. and Lux. The 1926 production, amounting to 10,650 bbl., was only 400 bbl. short of the maximum reached during any year of the 10-year period that the process has been in operation. Inasmuch as the Hamilton Corners pool is the first one in Pennsylvania in which the Marietta process was tried out, and the one in which it has been longest in continuous operation, considerable interest attaches to the results obtained. Through the courtesy of H. D. Brown and W. J: Brundred, officials of the Brundred Oil Corpn., all their data on this operation were made available to the writer in connection with an investigation of rejuvenation methods in the State for the Pennsylvania Geological Survey.

Jan 1, 1928

By H. M. Woodrooffe

This paper deals with the laboratory facilities at the Mines Branch for carrying out research in the industrial minerals field, and also reviews current programs in ceramics and construction materials, in non-metallic minerals and in the milling of industrial minerals. It then discusses the application of these pro-grams to industrial problems.

Jan 1, 1967

By J. T. I. Poijärvi

The smelter off-gas cleaning and the weak acid treatment at Outokumpu Harjavalta Metals Oy are presented and described in this paper. The smelter consists of the copper and nickel smelters and the acid plant of three separate acid plants two of which are double contact and one single plant and of one liquid sulphur dioxide plant. The preliminary cooling and flue dust separation of the smelter off....,gases from the copper ?and nickel flash smelting furnaces and converters? in the waste heat boilers and in the hot electrostatic precipitators are described. The final cooling and cleaning of the gases in the scrubbers at the sulphuric acid plant and the treatment of the weak acid in the vacuum and in the submerged combustion evaporators for the removal of impurities are presented as well as the treatment of the condensates from the evaporators. The attention is paid to the generation of sulphur trioxide in the smelter off-gas.and to the treatment of that in the weak acid bleed-off and to the utilization of the treated acid.

Jan 1, 1992

By Zay Jeffries

HOSTILITIES in Europe, Asia, and northern Africa were responsible for dislocations in rare-metal supplies during 1940. Although the consumption of some of the rare metals is small the dislocations may be relatively large. In some cases these are advantageous to North America and in others they are disadvantageous. Specific instances will be cited later. Barium T HIN films of barium metal on special steel balls greatly improve the life and reduce the friction of rotating anodes in highly evacuated small X-ray tubes and make possible the operation of these anodes at relatively high temperatures. These remarkable results are described in an article by Atlee, Wilson, and Filmer in the Journal of Applied Physics for September, 1940. Oil could not be used because of the high temperatures on the one hand and its volatility on the other. Fig. 3 shows diagramatically the rotating anode and the method of coating the steel balls with barium. The letters K.I.C. refer to "Kemet Iron Clad." The K.I.C. wire was mounted so that the barium could be evaporated by direct passage of the electric current. At high temperatures the barium dif-

Jan 1, 1941

By A. Majumdar, B. Servière, H. Persson

The CCR refinery, which was built in 1931, treats both internal and third party copper anodes to produce 325,000 mt of copper as cathodes. These anodes contain high levels of impurities, such as Ni, As, Sb and Bi, that reports to the electrolyte during the refining step and need to be removed in order to maintain cathode quality and operating efficiencies. In the purification plant, the electrolyte is de-copperized via electrowinning in three stages. In the last stage, the copper content of the electrolyte is reduced to below 1 gpl in order to maximize the co-deposition of As, Sb and Bi with the Cu. This is accomplished with minimum arsine gas generation by using periodic reversal of the current and by controlling the final copper content of the electrolyte. Nevertheless, the possibility of exposure to arsine is treated as a major risk and controls have been implemented to reduce this risk. This paper describes the controls in place at the purification plant, which are being continuously improved through periodic risk assessments and audits. INTRODUCTION The CCR Refinery, which is a part of Glencore Canada Corporation and located in Montreal-East, Quebec, is a custom copper and precious metal refinery, with a capacity to refine 325,000 tonnes of copper anodes per year. Copper anodes are received from the Horne smelter in Rouyn-Noranda, Quebec, Altonorte smelter in Chile and other 3rd party smelters. CCR anodes are produced using the spent anodes from the tankhouse along with purchased spent anodes and copper scrap. The precious metal plant treats the tankhouse anode slime, purchased anode slime, precious metal ingots and Doré anodes from Glencore’s Brunswick lead smelter in Belledune, New Brunswick. CCR products include copper cathodes, silver and gold bullion, a platinum-palladium concentrate, selenium, tellurium dioxide and nickel sulfate. In 1975 an accident occurred at CCR where two employees were exposed to fatal levels of arsine emitted from the then existing purification cells. This process was therefore shut down immediately. Research and development work was then initiated to determine the optimum electrowinning conditions whereby arsine gas generation would be minimized while maintaining high copper and impurity removal efficiencies. It was found that the application of periodic reversal of current (PRC) during the last stage of electrowinning retarded the onset of arsine formation while at the same time allowing the copper concentration to be reduced to less than 1 gpl (Houlachi & Claessens, 1978). A new purification plant was designed based on the PRC technology and was started up in 1976. In addition to the use of PRC electrowinning, the new plant is located in a fully enclosed section of the tankhouse. A special effort was made to design a ventilation system to evacuate the acid mist in addition to any arsine gas. Arsine monitors were installed to measure the emissions from the stack along with arsine levels in the workroom. The arsine monitors and the ventilation system were interlocked with the rectifiers (Thiriar et al., 1983).

Jan 1, 2019

By D. H. White

The term "block caving" as used in this text includes panel caving and mass caving as described by Julin and Tobie (1973). This method reportedly was conceived in 1895 when a block of ore ranging up to 200 ft (61 m) in width was undercut at the Pewabic Mine on the Menominee Range in Michigan (Bucky, 1956). Over the years this method has evolved largely as a consequence of trial and error in which operators became acutely aware of what nature would allow and what it would not. Today block caving remains somewhat of an art rather than a science where experience often dictates what needs to be done. With the plunging prices of base and specialty metals in the early 1980s caving mines sought to reduce operating and development costs in order to return to profitability. For some this became an impossible task given the design, grade and operating costs of the day and closure became the only alternative. One lesson learned from the experiences of the 80s is that survivability depends on cost competitiveness and this implies the efficient use of resources and technology. To this end applied rock mechanics serves as a useful tool. The purpose of this paper is to show how Geomechanics can be used? in block caving to facilitate sound decision making and how this equates to dollars saved. Features of mining method selection, design and operation are discussed as related to this theme.

Jan 1, 1990

By Joseph M. Singer

This research project had two main objectives: (1) To identify the smoke limits of gaseous fuel-air mixtures and (2) to obtain and evaluate basic chemical information on the formation of smoke in very rich flames near the smoke limit. Such information would do much to establish the circumstances for car-bon deposition in gas appliances and in other types of combustors. Based on tests with ethylene and propane, these studies showed the following: 1. Smoke limits are related to the yellow-tip limits of the fuel. Previous research established sufficient data to permit prediction of yellow-tip limits on gas burners using a wide variety of fuels. The present study of smoke limits deals only with ethylene-air flames, but the concept that was developed is probably applicable to other fuels.

Jan 1, 1962

By Deventer Johanna van

Ore bodies around the world are declining in grade, whilst increasing in complexity. The level of impurities relative to the valuable metal is steadily increasing, posing new challenges to existing operations. Ion exchange is widely used in the hydrometallurgical industry for both primary recovery of metals and the removal of impurities. The superior selectivity of ion exchange resins makes them exceptionally suitable for the removal of target impurities to very low levels, thereby saving operating costs, increasing the value of the final product and significantly improving revenue. The ion exchange process in these applications is very simple, using standard ion exchange equipment and acid regeneration. The process can be fully automated, requiring minimal operator interference and supervision Examples of impurities that are successfully removed via ion exchange include iron, antimony and bismuth from copper electrolyte. In the copper electrolysis process, antimony, bismuth and arsenic tend to form slimes which are dispersed in the electrolyte. These slimes contaminate the cathode and/or decrease the quality of the copper deposition. A special chelating resin was developed to remove antimony and bismuth, while at the same time ensuring minimal chloride leakage to the sulphate matrix. The work is described in more detail in this paper. Ion exchange is also used to remove copper, zinc and nickel from cobalt electrolyte. This paper addresses a few of these examples in more detail.

This paper cites selected, prominent examples of current, major projects in Southern Africa in both the mining and civil fields. Differences and similarities in the life cycle of mining and civil projects are discussed. A closer relationship between the mining and civil fraternities is beginning to develop and should be encouraged because of the resultant exchange of experience and technology which benefits both disciplines. An attempt is made to assess future potential for new, major projects and trends in the implementation thereof.

Jan 1, 1999

By M. Aushouri, S. H. Mansouri, N. Aminizadeh

A thermo-chemical model of the Peirce-Smith copper converter has been developed to predict the molten temperature. The primary assumption of the model was that all matte, slag and gaseous phases in the converter were in thermal and chemical equilibrium. In this model, the matte components were considered only as copper, iron and sulfur elements. In the slag making stage, all the reacted iron was converted to fayalite. The reaction rate of iron and oxygen in this stage was considered to be constant. The converter temperature was calculated by heat balance over time. The model was validated by a detailed comparison with measured industrial data. A good agreement was obtained. The converter temperature depends on process parameters such as oxygen efficiency and molten emissivity.

Jan 1, 2007

By Xiaojie Gao, Jingshe Li, Chengsong Liu, Haiyan Tang

In order to clarify the reaction between MnO-SiO2 oxides with low FeO content and Fe-Mn-Si alloy, two diffusion couples were produced by the new method using confocal scanning laser microscopy (CSLM). The interface of the alloy and oxide, content of Mn and Si in the alloy near the interface, size distribution and composition of the particles which precipitated in the alloy were observed and analyzed using the electron probe microanalysis (EPMA). Results show that though the FeO content in the oxides decrease to 1% which is lower than the equilibrium with the molten steel at 1873K, the diffusion of oxygen from oxide to alloy still exists during the heat treatment at 1473K and causes shorter Particle Precipitated Zone (PPZ) and Manganese Depleted Zone (MDZ) normally for the reduction of diffusion flux of oxygen.

Jan 1, 2015

By Thomas A. Wheeler

The reagents commercially used in coal flotation and their roles are reviewed and discussed According to their function the reagents are divided into often overlapping groups: 1. Collectors 2. Frothers 3. Conditioning Reagents Frothers have by far the largest effect on the amount of coal recovered They act not only in their traditionally accepted function of “bubble makers”, but in coal flotation they serve in a seldom acknowledged role of collectors. A lab flotation study on four samples of different coal ranks shows how these react to various frother families and proves that no froher is the optimum reagent for all types of coal. The advent of new technology in flotation equipment in the past decade has resulted in various novel designs of column cells, Jameson and Centrifloat™ cells, air-sped hydrocylones, etc. All should require special frothers or blends of frothers to meet their specific needs.

Jan 1, 1994

By C. E. Armantrout, H. Kato, M. I. Copeland

The data collected during this investigation indicate that the chromiumgadolinium system has extensive liquid immiscibility and one eutectic point . Liquid immiscibility occurred at temperatures above the monotectic isotherm , 1,830 ° C , which extended from less than 0.25 to about 85 weight - percent gadolinium . The eutectic was at 96 percent gadolinium and 1,170 ° C. Gadolinium and chromium were the only phases in this system . There was a solid solubility of less than 0.25 percent gadolinium in chromium at 1,730 ° C and less than 0.10 percent chromium in gadolinium at 1,160 ° C. The alloys were prepared by nonconsumable - electrode arc - melting , and the alloy system was investigated by heat treatment , metallography , thermal analysis , and X- ray diffraction . All the melting , heat treatments , and thermal analyses were conducted in a vacuum or in helium because of the reactivity of chromium and gadolinium with the components present in the atmosphere at elevated temperatures .

Jan 1, 1964