Search Documents

By A. Warczok

Smelting slags contain payable metals in a dissolved form and as mechanically entrained matte or metallic inclusions in the size range from 2 to 1000 µm. Slag cleaning requires reduction of magnetite and metal oxides and sedimentation of inclusions. Slag cleaning in an electric furnace is carried out in batch or semi-continuous mode. The strong trend for continuous slag cleaning generates the basic question about the optimal geometry of the electric furnace. Results of combined CFD, potential distribution and heat transfer modeling allowed for the determination of the fluid flow pattern and the temperature distribution in a classical, circular electric furnace as well as in a rectangular furnace. For the rectangular furnace, various length/width ratios and position of electrodes have been simulated. Analysis of key phenomena pointed out the advantages of the rectangular electric furnace over the circular furnace, particularly for continuous slag cleaning. Phenomena that have been analyzed were mass transfer, the rate of slag reduction, coalescence and settling of inclusions, all on the basis of the calculated slag flow pattern and the temperature distribution.

Jan 1, 2007

By S. F. Diehl

Weathered mine waste consists of oxidized primary minerals and chemically unstable secondary phases that can be sources of readily soluble metals and acid rock drainage. Elevated concentrations of metals such as Cd, Cu, Fe, Mn, Ni, Pb, and Zn are observed in deionized water-based leachate solutions derived from complex sedex and Cu-Pb-Zn mine wastes. Leachate (USGS FLT) from the Elizabeth mine, a massive sulfide deposit, has a pH of 3.4 and high concentrations of Al (16700 ug/L), Cu (440 ug/L), and Zn (8620 ug/L). Leachate from the sedex Faro mine has a pH of 3.5 and high concentrations of Al (2040 ug/L), Cu (1930 ug/L), Pb (2080 ug/L), and Zn (52900 ug/L). In contrast, higher-pH leachates produced from tailings of polymetallic vein deposits have order of magnitude lower metal concentrations. These data indicate that highly soluble secondary mineral phases exist at the surface of waste material where the samples were collected. Sulfide minerals from all sites exhibit differential degrees of weathering, from dissolution etched grain rims, to rinds of secondary minerals, to skeletal remnants. These microscale mineral-dissolution textures enhance weathering and metal leachability of waste material. Besides the formation of secondary minerals, sulfide grains from dried tailings samples may be coated by amorphous Fe-Al-Si minerals that also adsorb metals such as Cu, Ni, and Zn.

Jan 1, 2011

By Wendy Hutchinson

Jan 1, 2007

By Andy Ingriselli, Andrew Famiglietti, John Westland, Greg Landry

Atlas Dewatering was contracted to install and maintain a groundwater control system for the new Bessarion Subway Station and the Tail Track Structure on the Toronto Transit Commission’s new Sheppard Subway Line. Atlas met the challenges presented by the project by closely reviewing the contract documentation provided by the Program Geotechnical Consultant, Golder Associates and by working with the general contractors, Bondfield Construction Company and PCL Constructors Eastern, inc., throughout the duration of both projects. In addition to concerns about soil loss, excessive settlement and seepage, the consultant was concerned about spreading hydrocarbon-contaminated groundwater between the two aquifers present at the Bessarion Station site. By installing a system of multi-level vacuum eductor wells around the perimeter of the excavation, Atlas was not only able to provide a dry excavation for construction, but, due to a unique well design was also able to prevent cross-contamination of the aquifers.

Jan 1, 2001

By Daniel D. M. Adams

In 2004, Rio Tinto started a major project to implement Mine Monitoring and Control (MMC) systems worldwide. A detailed selection processes was undertaken and migration to a standard system was started. Today systems are operating around the world and serve as the core of to many business processes. Implementations include highly union areas, large mines, centrally managed mines, and remote areas. Each implementation has unique challenges but all are working towards the common goal with common systems. This paper reviews two projects that Rio Tinto has deployed in diverse conditions. The projects are the Rossing Uranium upgrade from the original Wenco system to the common standard and Iron Ore of Canada?s general technology upgrade. Also discussed is the future of mining at Rio Tinto, specifically the drill automation projects, and how it is utilizing the common standard MMC systems.

May 1, 2010

By James Ridenour

The Gearhart Mountain Wilderness and RARE II area 6225 encompass 22,823 acres (9,236 ha) of the Fremont National Forest in southern Oregon (fig. 1). The area was studied under the provisions of the Wilderness Act of 1964 (Public Law 88-577). The U.S. Bureau of Mines determined the mineral potential of known mines, prospects, or mineralized areas, while in a separate effort the U.S. Geological Survey made geological, geochemical, and geophysical studies. MINERALIZED AREAS The study area contains no mining districts or known claims. Nearby occurrences of uranium, base metals, perlite, mercury, and diatomite apparently do not extend into the study area. Reconnaissance pan samples reveal only trace amounts of gold. No anomalous economic minerals were found in heavy mineral fractions of samples from stream beds draining the area.

Jan 1, 1982

By AIME AIME

FREDERICK WORTHEN BRADLEY, the newly elected president of the Institute, may be said to be the prototype of the men who have built up the great mining industry of the West. He was born in Nevada County, Cal., on Feb. 21, 1863, and studied mining at the University of California from 1882 to 1884, as a member of the Class of 1885. He was in contact with the mining industry from his earliest years and in his reminiscences which we published last month, he told of meeting Thomas Mein and H. C. Perkins in 1877. Beginning as assayer and roustabout at the Eagle Bird mine, in Nevada county, Mr. Bradley was a deputy mineral surveyor in 1886 and 1887 and superintendent of the Spanish mine from 1885 to 1890. There he made a record of mining gold ore at 65 cents per ton that was not only astounding in that day when modern large scale mining had not yet been developed but is still a mark to shoot at. As a result he was called in 1890 to be assistant manager of the Bunker Hill and Sullivan and was made manager in 1893. In 1897, he was elected to the presidency of the company, a position he still holds. H. C. Perkins and D. O. Mills, the largest stockholders in the Bunker Hill and Sullivan Co. took over the Tacoma smelter in 1898, feeding it with concentrate from the Coeur d'Alene and Douglas Island mines but also doing a gen-era1 smelting business. Mr. Bradley was put in as president of the Smelting company, and held that position until the plant was sold to the American Smelting Securities Co. in 1905.

Jan 1, 1929

By A. E. Ketler

Optical smoke monitoring fills an important gap in ventilation and fire safety: namely monitoring of smoky, low temperature fires where little CO and heat are generated. Smoke monitoring also avoids the nuisance alarms due to diesel exhaust, battery chargers, blasting and welding. The smoke optical density (OD) fire alarm standard specified by MSHA presents an opportunity for improved safety. Experience of actual mine usage of the SmokeBoss*100 is reviewed, with particular regard to effectivity, maintenance and cost.

Jan 1, 1995

By T. Tomioka

1. An Overall View of the Japanese Ferroalloys Industry 1) Depressed Demand for Ferroalloys: In Japan consumption of ferroalloys in the last ten years has decreased, although there has been some fluctuation from year to year. During this term production figures of the steel industry, which are closely related to consumption of ferroalloys, are as follows: Shipment of steel products for the domestic market has declined gradually from 69 million tons in 1979, which was the peak year for steel production, to 60.3 million tons in 1982 and 60.4 million tons in 1983, the level of 1978. In addition, exports also have been a downward trend since 1976, which was the peak year with tonnage of 34 million tons, to 28 million tons in 1982 and 31 million tons in 1983.

Jan 1, 1984

By Thomas T. Read

IN reviewing the field of mineral industry education last year reference was made to recent assertions, mostly emanating from sources not in a position to know the facts, that mining engineers as a class are disappearing. Attention might also then have been called to a statement that appeared in Engineering News, August 11, 1892 (p. 130), ". . . the great absolute decline in number of mining graduates, which last amounts almost to a complete abandonment of mining engineering as a distinct branch of study." Evidently we outrank opera stars in the number of farewell appearances we are able to make; 43

Jan 1, 1936

By E. A. Brocchi, D. H. Gameiro, P. K. Jena

Carbon tetrachloride was found to be a very efficient chlorinating agent for anatase concentrate, even at the low temperatures that were investigated (250-400 degrees C). For example, at 400 degrees C about 90% of the anatase concentrate was found to have been chlorinated within 60 minutes

Jun 13, 1905

By A. McMullen

"IntroductionTHE LOW-VOLATILE bituminous coals of the Brazeau field, Nordegg, Alberta, are soft and weak in structure. The seams contain .bands of inferior material, locally designated 'black jack', and thin bands of friable carbonaceous shale having no definite horizon but usually 'floating' in the seam. Because of the weakness• of the coal and the friable nature of the shale bands, run-of-mine coal usually contains a very high percentage of fines, as •Shown in the following table:SIZE WEIGHT. %Plus 1/2 in 25.61/2 – 1/4 in 13.31/4 - 1/8 in 14.6Minus 1/8 in 46.5The most convenient way of cleaning the fine coal would be by treating it in association with the coarse coal, so that no additional plant would be necessary. To a limited extent this is possible in certain types of equipment, notably the jig. A system of washing without pre-sizing is not •attractive, however, when dealing with the friable coal under consideration, which contains •a preponderant proportion of fines. At the new Brazeau washery, separation is made at 3/8-inch on •a Robins 'Vibrex' •screen, the coarse sizes being cleaned in •a standard pulsator-type jig. A feldspar jig is used to clean the minus 3/8-inch fraction."

Jan 1, 1954

By Javier Illanes Pizarro, Gustavo Huerta Valer, Jorge Cárdenas Miranda

Bench stability is the basis of sustainability in an open pit mining operation. Taking care of the pit walls while maintaining fragmentation results can prove a challenge. In this study, technical proposals have been developed for extra hard rock mass (UCS>175MPa) with presence of unfavorable structural planes in high copper grade zones. The base case shows low compliance of fragmentation results and a significant loss in berm width, with over size boulders causing low primary crushing rates. Paradigms in current drill and blast design were overcome to improve fragmentation results and achieve objectives.

Feb 6, 2023

By GEORGE L. CHRISTIAN

T HE Tonopah Extension assay office is a two- story, concrete structure on a solid foundation of andesite, situated about 100 yd. from the company's mill, so that it will not be affected by the stamps or the tube-mills; also it will not be affected by under- ground blasting. On the second floor are the mine superintendent's office and drafting and blueprint rooms. On the ground floor are the assayer's office,' mixing room, furnace room, crusher room, chemical laboratory, parting room, store room, and change and shower room for the mine superintendent, assayers, and engineers. The crusher room is outside of the main building, and has four concrete walls, thus eliminating the jar of the crusher; it is so situated that the least possible amount of dust spreads through the main building. An 8 by 10-in. jaw crusher, which crushes to ¼ in., was made by a local foundry. Attached to the top is a small galvanized-iron hopper covered with a ¼ in. screen, on to which the sample is dumped. The fines-pass through the screen into the hopper, while the oversize is dumped into the crusher. The crushed sample and fines from the screen drop down to a set .of splits suspended from an iron rod below the crusher jaws. The small sample is caught below in a small pulp pan. The rejects drop from the splits through a 2-in. pipe on to a bucket conveyor, which dumps into a galvanized-iron hopper in an upper corner of the room. The rejects drop through a 2-in. pipe to a reject bin outside the build- ing. This bin is constructed high enough for a truck to be loaded from it by means of a chute door on the side.

Jan 1, 1921

By Russell McIntosh

"The Madsen mine is in the southeastern part of Baird township, in Red Lake area, Ontario. It lies about 6 miles southwest of the town of Red Lake, with which it is connected by an all-weather road.The Madsen Red Lake Gold Mines Company was formed in March, 1935, to take over the holdings of the Falcon Gold and Jomac Gold syndicates. During 1935 an4 the early part of 1936 No. 1 shaft was sunk and drifts driven on four levels, all on a narrow quartz vein in a granite dyke.In July, 1936, the Austin zone was discovered about half a mile north of No. 1 shaft by Austin McVeigh, a prospector employed by the Company. Diamond drilling showed that the zone included an orebody worth development, and in 1937 No. 2 shaft was sunk, three levels opened up and sufficient ore outlined to justify the installation of a mill. Milling commenced in August, 1938, at the rate of 300 tons a day, which was later increased to 400 tons a day.The total production from 1938 to 1946 was 1,116,307 tons from which gold and silver having a value of $9,949,010 were recovered. The gold produced ranged from a minimum of 0.1910 oz. a ton in 1939 to a maximum of 0.2827 oz. in 1944. The average grade in 1946 was 0.2345 oz. to the ton."

Jan 1, 1954

By TRUMAN S. FULLER

THE GREAT INTEREST in decomposition and trans- formation, so evident in the study of alloys during the last two years, was reflected in the many papers on this subject, presented at the first session of the Institute of Metals, Tuesday morning. Dr. F. A. Thomson, of Montana State School of Mines, presented the first paper by C. Wilson, H. F. Silliman, and E. C. Little, "Rate of Precipitation of Nickel Silicide and Cobalt Silicide in the Hardenable Copper-nickel-silicon and Copper- cobalt-silicon Alloys." Dr. R. F. Mehl, in discussing this paper, stated that the title was somewhat deceptive, as it indicated that the rate of precipitation is determined; the method used is a measurement of electrical conductivity and hardness, neither of which is suitable for a quantitative measurement of rates of reaction or precipitation in the solid state. Hardness is also uncertain because it depends so much upon particle size. Of the various methods proposed for the study of rate of reaction and precipitation the evaluation of volume of reaction produced from the area of photomicrograph is the best.

Jan 1, 1933

By M Yahyaei, P Knights, M S. Kizil, J Qu

Digital Twins (DTs) are transforming business operations across many industries through their accurate representations of physical entities enabled by IoT technologies.

Sep 1, 2024

By Yin Zhang, Xiaoyu Huang, Mi Wang, Bencheng Du, Youduo He

"Burners are important facilities for blast furnace stoves to raise hot-blast temperature up to 1200°C. Common types of two-ring ceramic burners have very long flames so that part of combustion occurs in the upper part of the chequers and will cause damage to the refractory materials. Using computer simulation to analyze the turbulent diffusion flame in the combustion chamber, some good results were obtained. A new type of ceramic burner will be installed by Anshan Steel Complex in stoves of blast furnace number 4. A pilot experiment was done on the new burner. The experimental data have shown that the mixing condition was improved and the length of flame was shorter with the new type of ceramic burner.IntroductionPulverized-coal injection can give significant operating saving, reducing coke rate in blast furnace(BF) operation. However, during high rates of coal injection, extra heat must be compensated in hearth to maintain certain raceway adiabatic flame temperature. One of the effective methods for heat compensation is to raise hot-blast (HB) temperature up to 1200°C. Nowadays, since the fuel being combusted in stoves is BF gas only, in which the calorific value is down to round 3000 kJ/m3 , to increase the combustion ability and to provide a suitable length of flame in combustion chambers of stoves becomes more important. In other words, designing a good ceramic burner which will affect to HB temperature and stove lifetime is drawing more attention."

Jan 1, 1999

By W. A. Wall, R. L. Kidd

IN present-day flotation practice, grinding of the flotation feed is carried to extremely fine sizes, 70 to 80 per cent minus 200 mesh being customary. The greatest flotation losses occur in the coarsest and finest sizes, but the losses in the very fine sizes are, of course, much the more important because of the large proportion of fines in the feed. These losses are particularly high in zinc ores so a study of the effect of size on the flotation of sphalerite has been made. The mineral used in these experi¬ments was a pure sphalerite, especially free from copper, from the Joplin district in Missouri. The sizes coarser than 200 mesh were separated by screening, the sized mineral then being deslimed on a Wilfley table. The sizes finer than 200 mesh were obtained by water elutriation as described by H. R. Bradford (M. S. Thesis, University of Utah, 1932) ; particles finer than 6.5 microns could not be obtained with the apparatus used.

Jan 1, 1933

By Jerome Strauss

IN his review of developments in 1943, Gilbert Seil, Chairman of this Committee on Reduction of the Ferroalloy Ores, tabulated the consumption of the alloying metals in relation to the steel production of that year. In the year just closed the approximate tonnage was of the same order, differing only to a minor degree or suffering some correction with more precise figuses available, as indicated in the following estimates: Consumption Metals in Tons Steel 92,000,000* Manganese 700,000 Silicon 200,000 Chromium 200,000 Nickel 75,000 Molybdenum 20,000 Tungsten 8,000 Vanadium 1,700 Titanium 1.600 Boron 10 `Production figure. The technologic studies instituted during 1942 and carried forward with such great vigor during 1943 continued into 1944 although in some instances were brought to a close either by completion of the specific development

Jan 1, 1945