Search Documents

By Yong .. Jun Wu

Laminated ceramics have received widely scientific and commercial attention because their properties, such as mechanical properties and electrical properties, can be tailored by adjusting the structure, thickness and composition of the different layers. For example, ferroelectric Bi4Ti3O12 (BIT) which has a positive temperature coefficient of dielectric constant (,E) can be used to modify the negative tE of typical microwave dielectric ceramic BaNd2Ti4O12(BNT), However, BaNd2Ti4O12/Bi4TiO12/Bi4Ti3O12/BaNd2Ti4O12 (BNT/BIT/BNT) laminated ceramics could not be prepared by the general method because the optimal sintering temperature of BaNd2Ti4O12 ceramic (around 1350°C) was much higher than that of Bi4Ti3O12 ceramic (around 1100°C). In this research, a new method of spark plasma sintering (SPS) combined with post-sintering was successfully proposed to prepare BNT/BIT/BNT laminated ceramics. It was divided into three steps. In first step, the BaNd2Ti4O12 ceramics were prepared by conventional sintering method. In second step, the calcined and pre-pressed Bi4Ti3O12 powders were sandwiched between BaNd2Ti4O12 ceramic pellets and spark plasma sintered at 900°C for 10min to synthesize BNT/BIT/BNT composite ceramics. In the last step, a post-sintering was employed to reoxidize the partially reduced BNT/BIT/BNT composite ceramics. The results of scanning electron microscopy (SEM) and electron probe microanalysis (EPMA) showed that BNT layer and BIT layer were well bonded and no significant interfacial infiltration between them was observed. The sandwiched BNT/BIT/BNT ceramic with 10.7% BIT in volume has a dielectric constant of 92.85, a low dielectric loss of 01068 and a small temperature coefficient of dielectric constant of 35 ppm/°C at MHz.

Jan 1, 2003

By Denise C. R. Espinosa

The amount of secondary batteries are increasing about 15% by year. Among these batteries, it can be highlighted the NiCd ones, due to their high consumption. In Brazil, the consumption of NiCd batteries grown quickly in the last 5 years, due to the dissemination of cellular telephones and other electronic devices. The first step of a process to recycle spent NiCd batteries is the pretreatment through unit operations of mining treatment. The aim of this work is to define a physical pretreatment to conditioning the waste to a pyrornetallurgical recycling process of spent NiCd batteries used in cellular telephones. Batteries were disassembled by hand to release the different components. The studied batteries are basically composed (by weight) of: 78% nucleus, 18% plastic case and 2% circuits. The grinding of the batteries was performed by knife mill and also by hammer mill. After grinding the material was screened and submitted to a magnetic separator.

Jan 1, 2001

By Hiroshi Tabuchi, Akihiko Takahashi

"High strength aluminum matrix composites were prepared and studied using as reinforcement newly developed nearly mono-dispersed a-alumina single crystal particles each of which has a regular polyhedral shape. The composites were formed by centrifugal casting using aluminum casting alloys (Al-Si and Al-Cu-Mg) as the matrices, followed by heat treatment. The volume fraction of the alumina particles was as high as 60%. The same matrix composites reinforced by conventional crushed fused alumina particles were similarly prepared as the reference. The bending strength and tensile strength of the Al-Cu-Mg matrix composites reinforced by the novel alumina particles of 10 µm in average diameter are as high as 1020 MPa and 560 MPa, respectively, which are higher than those of the conventional alumina composites. Furthermore, the bending strength of the novel alumina composites degraded less than that of the conventional alumina composites after thermal fatigue tests. The number of cracks in the matrix seemed to influence the thermal fatigue property because many cracks were observed in the conventional alumina composites, whereas only a few cracks were observed in the novel alumina composites. This was confirmed by SEM observation of the sample composites before and after the thermal fatigue tests.IntroductionAluminum matrix composites strengthened by dispersed reinforcements are of interest for various applications due to their improved properties, such as high specific strength and stiffness, wear resistance, etc .. A large number of investigations have been made concerning fabrication processes and properties of these composites. With regard to the fabrication processes, powder metallurgy has been well-known as a solid phase process, and recently many liquid phase processes such as a compocasting, a squeeze casting, the Lanxide process, and the Osprey process have been studied and developed.(1)"

Jan 1, 1998

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy's program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997

By E. R. Bauer

The ground control aspects and occupational safety concerns of extended depth-of-cut mining are presented in this U.S. Bureau of Mines (USBM) report. The scope of extended cut use and typical face operations while extracting extended cuts is reported. A comparative review of roof fall fatalities and a statistical analysis of accidents and injuries for both extended and nonextended cut mining is included. The views and opinions on extended cutting from a series of interviews with mine workers in five states are summarized. In addition, some of the problems and safety concerns of this extraction system are mentioned.

Jan 1, 1995

By AIME AIME

THE fall meeting at El Paso this year (Oct. 13¬15) will be of unusual interest due to the international atmosphere imparted by the many engineers from Mexico, who are making arrangements to attend this meeting. The meeting will be held jointly with the Western Division of the American Mining Congress. Cooperating in the program will be the representative society of Mexican engineers known as Centro National de Ingenieros of Mexico City, who are plan¬ning on sending many delegates and well known Mexican engineers to the convention. The cooperation of the West Texas Geological Society and the American Association of Petroleum Geologists has also been secured. Brent N. Rickard, manager of the El Paso Smelting Works of the American Smelting & Refining Co. at El Paso, Tex., is general chairman in charge of arrangements. He is receiving splendid cooperation from the Mining Department of the El Paso Chamber of Commerce and from the business people of El Paso, who feel highly honored in having these mining societies meet with them this year.

Jan 1, 1930

By D G. Oldfield

Pall has developed and supplied to several airlines cabin air libers to provide clean air for passengers and crew in flight, while reducing airline operating costs. Most of today's modern commercial passenger aircrafts employ cabin air recirculation as a means of reducing operating costs. With large numbers of passengers being subject to an increasing proportion of recirculated air for hours at a time, the matter of cabin air quality, with particular respect to the health effects on passengers and crew, has to be addressed. Commercial pressure will ensure that the airlines and aircraft manufacturers will not revert back to the total fresh air systems of the 1960s and 1970s. In fact, feasibility studies are already being undertaken to look at increasing the proportion of recirculated air to 80% and above. With the application of specialist nitration technologies. Pall is able to ensure that the requirements for economy are met whilst ensuring that the air is effectively rendered as 'fresh air’ each time it is recirculated.

Jan 9, 1996

By X. L. Song, G. W. Zhang, F. Y. He, X. Xiao, L. L. Huang

This paper presents the design of a model and process simulation of a vertical mill based on a population balance model. The simulator, Simulink, which is a systematic modeling tool within MATLAB, was used for the simulation. The model will simulate the real time variation trend of each size fraction in the feed material to the vertical mill, as well as, the size distribution of the batch grinding products. Breakage distribution and selection functions are calculated based on batch grinding laboratory experiments using Back-calculation method. The simulated size distributions correspond with those in the actual mill operation having a relative error of less than 0.50%. This work lays the foundation for future research on modelling and simulation of a closed circuit grinding operation consisting of a vertical mill with hydrocyclone classifier.

Jan 1, 2016

By Joseph Clare

It’s not the 1960s anymore. Upgrading wastewater pipelines in the current era demands the latest trenchless technology to minimize impacts. King County Wastewater Treatment Division in Seattle, Washington is designing a nearly mile long Direct Pipe® influent sewer combined with microtunneling to replace a 1960s era trunk sewer constructed along and within Coal Creek and its natural area. Trenchless installation using Direct Pipe® and microtunneling was chosen due to reduce impacts to residential neighborhoods, natural creek environments, and the constraints of topography

Jun 13, 2021

By W. Holdsworth

The flotation mill of Dentonia Mines, Limited, at Greenwood, B.C., went into operation on April 20th, 1934, and by October 11th a total of 15,000 tons of ore had been treated. It is intended in this paper to describe briefly the operation and to give some of the operating data which have been gathered. The metallic minerals in the Dentonia ore are pyrite, chalcopyrite, galena, and, occasionally, native gold, and the gangue includes chloritic material, vein quartz, and calcite. Pyrite makes up about 90 per cent of the metallic content of the ore, in which it is disseminated as irregular grains and well-formed cubes. An average analysis of the ore is: gold, 0.27 oz. per ton; silver, 1.73 oz. per ton; copper, 0.12 per cent; lead, 0.31 per cent; and zinc, trace. From the mine ore-bin, situated near the portal of the tunnel at the mine, the ore is hauled by motor truck to the mill, a distance of three-quarters of a mile, and there dumped into the receiving bin, which has a capacity of fifty tons. The hauling is done during one eight-hour shift, commencing at 7 a.m. The maximum size of the ore fed to the mill-bin is ten inches. Lumps larger than this are broken by sledge hammer to pass through grizzly bars, spaced ten inches apart, installed above the bin. The ore is drawn from the bin by a 30-inch, 6-ply conveyor belt, 18 feet 6 inches long. In the near future, when the cross-cut tunnel is completed, the ore will be trammed to the receiving bin. This will effect a considerable saving in cost. At the same time, the bin will be set back several feet, so that the length of the conveyor belt may be doubled. This will make efficient ore-sorting possible, and so ensure a minimum of waste rock in the mill feed.

Jan 1, 1935

By T. W. Camm

The Bureau of Mines conducts studies of the economic impacts of regulations on federal lands. These studies are part of the Bureau Potential Supply Analysis (PSA) program. To meet the needs of these studies, a methodology was developed to estimate operating and capital costs for a mineral deposit given its tonnage, grade, and depth. The format for the cost models in this study was developed at the Bureau's Western Field Operations Center (WFOC), Spokane, W. A., for studies of known and undiscovered resources on Federal lands. These cost models are described in a Bureau publication by Camm (1991).

Jan 1, 1993

By John Fallavollita

Conventional gas atomization produces powders that vary widely in size distributions and microstructures, thus making it very costly to produce powders tailor made in a narrow size distribution and microstructure. Furthermore, it is difficult to determine the relationships between atomizer operating conditions and resulting powder characteristics. The Impulse Atomization Process (IAP) was developed at the Advanced Materials and Processing Laboratory to produce powders with narrow size distributions. Powders produced by the IAP were reproducible and their sizes could be easily controlled by adjusting experimental conditions. Characteristics of Zn, Sn-Pb, AI-Cu, and Cu powders will be described to illustrate the flexibility of the process to tailor-make powders.

Jan 1, 1994

By W. J. Mahoney

A good quality assurance program at a coal mine or power plant is accurate, timely, and consistent. The quality analysis is accurate due to a complete sampling of the coal stream loaded into the unit train. The sample analysis is accurate because standardized testing procedures are applied. Once the analysis is completed, the results must be communicated to the electric utility in a timely manner. The electric utility needs the results to better manage the coal inventory at the power plants. A quality assurance program can also help the mine deliver a consistent product to the electric utility's power plants. The importance of the three major tenants for a good quality assurance program: accuracy, timeliness and consistency, are based on major changes that are taking place in the electric utility industry.

Jan 1, 1994

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with CO2 is expected to occur at as low temperature as possible. In order to get a highly reaetive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of CO2. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining all the obtained data.

Jan 1, 2003

By Philip W. Holland

This U.S. Bureau of Mines (USBM) report describes a chromatographic method that is used for rapid field determinations of carbon dioxide in natural gas streams at a USBM helium production facility. The method employs a commercially available portable gas chromatograph that is equipped with a 10-m fused-silica capillary column coated with a porous polymer. The instrument operating parameters permit determinations to be performed over a concentration range of 10 ppm to 10 pct with a frequency of 20 samples/h. The speed at which determinations can be performed is an important factor when evaluating efficiency or troubleshooting processes at the helium facility.

Jan 1, 1994

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with C02 is expected to occur at as low temperature as possible. In order to get a highly reactive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of C02. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining al\ the obtained data.

Jan 1, 2003

By E. Bonsall, J. J. Brummer, A. R. Graham

"A method and device are described for sampling diamond-drill core by cutting a continuous fillet of constant cross section from the cylindrical surface of the core throughout appropriate sample lengths. The apparatus employs a tapered, abrasive-set, cutting wheel, the conical cutting surface of which projects slightly into a rectangular core-guiding trough set parallel to the axis of rotation. The depth of fillet and thus the amount of sample per unit length can be regulated by adjusting the core guides. The freshly cut fillet itself, by engaging in a guide beyond the cutting wheel, acts to prevent rotation of the core during operation of the device.The cuttings which form the sample are normally collected in a tray below the cutting-wheel and appear at about 80 per cent -100 mesh. They require little or no further treatment or comminution before analysis. Speed, economy and convenience of sampling are thus greatly increased as compared with conventional sampling by im-1>act breaking or sawing, followed by crushing, grinding and sub division for assayAssays from fillets (about 1/20 the cross-sectional area of the core) and from 180-degree segments, from the same ninety-three core-samples, representing 431 feet of nickel-copper mineralization, gave the following results:"

Jan 1, 1968

By Julyana G. Santana, Esperidiana A. B. Moura, Vijay K. Rangari, Olgun Güven, Angel Ortiz, Rene R. Oliveira

Ethylene-vinyl alcohol (EVOH) copolymers are widely used in the food packaging industry as gas barrier properties to oxygen, organic solvents, and food aromas. EVOH is very sensitive to moisture and its gas barrier ability deteriorates in high relative humidity conditions.This work aims to prepare flexible films based on melt-blending high density polyethylene (HDPE) and ethylene-vinyl alcohol (HDPE/EVOH/EVA blend) reinforced with graphene oxide (GO). The HDPE/ EVOH/EVA/GO flexible films were prepared by twin-screw extrusion and blown film extrusion processing. The flexible films samples were characterized by tensile tests, TG, DSC and FE-SEM analysis and the correlation between properties was discussed. In addition, the oxygen permeability tests were performed at 23 °C, 0 and 90% relative humidity using an OX-TRAN (MOCON Inc.).

Mar 1, 2017

By Jie Ma, Bo Wang, Jieyu Zhang, Jian Zhao, Zheng Chen

"In this paper, solidification process of steel ingot was simulated by ProCAST software, based on cellular automaton-finite element (CAFE) model. A 22 t steel ingot was divided into continuous small zones (100x150x180 mm) in radial direction, then the temperature field, shrinkage cavity and porosity, particularly, the microstructure were simulated. The results show that: there was a columnar-to-equiaxed transition in microstructure on radial direction. Zones, closing to the center of the ingot, had a more developed and fined equiaxed zone, while zones closing to the periphery of the ingot had a more developed columnar zone. It indicated that temperature gradient has a great influence on microstructural morphology. Thus, the simulation results were highly agree with the experimental results, verifying the feasibility of this simulation method. It significantly reduces the time of simulation, and has important significance for predicting the microstructure of large steel ingot.IntroductionSolidification microstructure of steel ingot have a significant effect on the quality of the final steel products. Although many experimental works have been carried out in order to obtain the optimum condition for solidification process of continuous casting, it is also very desirable to establish mathematical models to simulate the evolution of solidification structure. The simulation methods can be divided into deterministic models and stochastic models, which have been developed rapidly over the last couple of decades. Cellular automaton method is one of the stochastic models. Rappaz and Gandin [1, 2], Nasatac and Stefanescu [3, 4] are the earliest researchers engaged in the this field. Moreover, Rappaz and Gandin simulated the solidification structure and CET (columnar grain to equiaxed grain transition) of metals using the CAFE method (cellular automaton-finite element method) for the first time [1, 2]. Recently, the CA (cellular automaton) model also considered the effects of fluid flow on the solidification process. Zhu, et al. [5-11] improved method of CA , they used the KGT model to describe the undercooling needed during the growth of the dendrite tip."

Jan 1, 2014

By Xuemei Zheng, Aiyuan Ma, Guojiang Li, Tingfang Xie, Jinhui Peng, Libo Zhang

A new microwave roasting technology for the removal of Cl from zinc oxide dust is proposed in this paper. The effect of important parameters, such as roasting temperature, holding time and stirring speed, were investigated and the process conditions were optimized using response surface methodology (RSM). The experimental results show that zinc oxide dust dechlorination rate can reach more than 95.66% and meet the requirements of wet smelting electrolysis when controlling the stirring speed of 60 r/min,roasting temperature of 650 °C, holding time of 30 min. In addition, the effect of roasting temperature and holding time on removal ef ficiency of Cl was most signi ficant. As a result, the Cl content was decreased without the risk of pollution. This makes it as a good choice for a more ecological treatment of zinc secondary resources.

Mar 1, 2018