Search Documents

By James Hyslop

THE Pittsburgh seam in eastern Ohio has an average thickness of 5 ft and lies almost level Immediately above it is a layer of draw slate about 12 in thick, which normally has little structural strength, and is pulled down or allowed to fall as mining progresses Above the slate is a, variable thickness of roof coal, which in places will stand for the life of the working section and sometimes for the life of a secondary haulage entry The thickness of this roof coal varies from zero to 24 in In general, however, it does not provide a satisfactory roof, and usually is supported or pulled down About it is a mass of shale, soapstone and clay, of quite variable thickness, usually running from 5 to 8 ft and above this is a stratum of hard blue limestone, which provides a permanent roof Where entries are to be used for less than five years, the roof usually can be supported by wood or steel crossbars, but if they are to be used for a longer time, roof support is a serious problem All the roof material below the limestone disintegrates when exposed to air or moisture, and in a few years falls out between and over the crossbars Where this material is removed for a considerable height above the coal, the ribs scale and thus contribute to a further collapse of the roof As the height of the entry increases, cost of timbering is greatly increased, a problem that always is encountered where old entries are recovered or repaired METHODS During the last six years the Hanna Coal Co has used gunite for roof protection in mine entries Two general methods of guniting are practiced The first consists of the application of a I-in coating of unreinforced material This application does not provide any appreciable structural strength, and serves principally to protect the strata from exposure to air and moisture With the other method a coat at least 2 in thick is applied and provided with suitable reinforcing, which provides a structural strength proportional to the thickness of the coat and the reinforcing used The first method is adopted as a general practice, modified only where additional support is required "Gunite" is a mixture of cement, sand and water * The cement and sand are thoroughly mixed and screened before being fed into the hopper of a cement gun After the hopper lid is closed, compressed air is applied to force this dry mixture through the hose line to the nozzle, where the quantity of water needed to effect the proper hydration of the cement is added The coating is dense, and stronger than poured concrete

Jan 1, 1941

By J. M. Belland

This paper deals with the geology of the Smallwood mine in relation to its influence on mining and milling operations. Structure within the orebody, and variations in ore grade and material types, will be described and associated with the various drilling, blasting and milling operations. The orientation of planes of weakness, either bedding or jointing planes, and contacts between extremes in material types influence the size of the broken material. Generally speaking, variations in grinding rates and recovery can be associated with stratigraphic sequence and metamorphism.

Jan 1, 1966

By AIME AIME

FEATURES of the second fall meeting of the Petroleum Division for 1941, held at the Ambassador Hotel, Los Angeles, Oct. 29-30, were the forum on the Paloma Plan on Thursday after- noon, the large attendance from east of the Rockies, and the dinner on Wednesday evening sponsored by the Southern California Section and at which President Suman spoke on the strategic minerals and metals situation. The attendance was large and the technical fare uniformly good ; the presiding officers had the proceedings well in hand at all times and kept things humming. Some- times it was necessary to taper off the discussion because of pressure on time. All this was due to careful groundwork before the respective sessions. These presiding officers deserve citation: L. W. Huebel, Howard Pyle, E. K. Parks, Carlton Beal, E. G. Trostel. R. W. French, Jr., John Dodge, and H. N. Marsh. The Los Angeles local commit- tees and the Southern California Section deserve much credit for the arrangements, which were recognized by suitable resolutions at the end of the meeting.

Jan 1, 1941

By M. Woodie

INTRODUCTION Information such as application review to choose the proper style of vibrating screen, parameters that determine the proper size of vibrating screen, engineering design information that governors proper screen design, review of topics that govern proper isolation from structural steel and other topics that dictate proper screen selection for applications will be presented in this paper. Topics like process and application information review to choose the style of screen and how material size and type influences proper type of screen selection (multi-slope, incline, horizontal, linear incline or dewatering) will also be discussed. Parameters will be reviewed that help size the screen for the application. The total amount of surface area to size a screen is critical to the overall success of a screen installation. Once proper style of screen is determined there is an engineering process that is required to design the screen to operate correctly in the environment it will be used. Finite Element Analysis, Dynamic Modeling, Field Vibration Analysis and other engineering tools will be reviewed to best implement a successful vibrating screen installation. TYPES OF SCREENS Multi-Slope Multi-Slope vibrating screens are used where sizing large amounts of tonnage on surface areas that would be smaller than conventional screening where roughly 6” (150mm) minus material is required to be sized. Occasionally larger particle sizes can be screened on the Multi-Slope machine but the effectiveness of the machine can be diminished with larger particle sizes and larger than 4” (100mm) screen opening. The most common and effective size range of screening with these machines is 2” (50mm) minus material. The Multi-Slope screen is used where particle size is not extremely important. Mineral processing, hard rock mining and industries where exact material size is not critical are best suited for this equipment. Because the aggregates industry requires very specific material sizes, the Multi-Slope screen is not suited for most aggregate screen applications. The key to the success of a Multi-Slope screen is proper material presentation at the feed end of the screen. This allows for the material to stratify quickly and disperse the fines through the screen quickly with a relatively thin bed depth at the feed end which allows the undersize material through the screen quickly.

Jan 1, 2019

By L. H. McKay

Tailing Dams Three types of dam have been structed to impound tailings from the Allenby mill: 1.- By classifier unit 2.- By earth dam 3.- By direct deposition of tailings The first type, which includes two dams, was built across a shallow valley which sloped down to Similkameen river, just below the mill site. Two earth embankments, one below the other, were built across the valley. Tailings were then piped to Akins classifiers mounted on wooden wheels. The classifiers were set up at one side of the valley and gradually moved ahead on the sand embankment created by the sand discharge from these classifiers, the slime overflow going to settli.ng ponds formed by the dams. Decanting wells were built in the settling ponds by placing four six-by-six timbers vertically in the ground, two feet apart, to which two-by-six tongue-and-groove boards were nailed. The elevations of the ponds were raised, as required, by nailing additional two-by-six boards on the well and bolting on more six-by-six timbers when required. The bottoms of the wells were attached to a covered launder made of three-inch lumber laid on a one per cent grade. This launder carried the overflow through the dam. The second type of dam was built across a long, narrow valley, known as Hitchen's Flat, the upper ~n d of which was about 2½ miles north of the mill. This valley, an ideal tailings site, was 4,000 feet long and from 600 to 800 feet wide. An earth embankment with a concrete spillway through the top was built approximately 28 feet high across the lower end of this valley. Tailings were then dumped into the upper end of valley, with no further expense until the basin was filled up to the level of the flume where this entered the valley. When the upper end of the valley was filled to this point there was still room for more tailings at the lower end. Therefore, a pump was installed to elevate the tailings to build a wall around the upper end of the valley by depositing sands from a launder built up on 20 foot supports and sloping both ways from the pumping station around the upper end of the basin.

Jan 1, 1950

By B. I. Pålsson, H-Å. Häggblad, J. F. Stener, P. Jonsén

"Understanding mill charge motion is important. In the charge, the center of gravity is shifted from the rotational center of the mill system, and its motion is induced by rotation of the mill. At the same time, the charge creates a torque in the mill system. Breakage of ore particles and wear of liners/ball media are closely linked to this motion. To study these phenomena in a physically correct manner, numerical models for different parts of the mill system are needed. Validations of such models are scarce, because of the difficulty of measuring inside a tumbling mill. Experimental measurements in a lab mill were done for a number of load cases: varying feed material, mill filling, mill speed and pulp liquid. The mill is set up to measure the charge-induced torque. The accuracy is good, with relative uncertainty less than ± 2% for relevant load cases. A full three-dimensional numerical model of the whole mill is used to predict induced torque. Agreement between predicted and measured torque at steady-state is good. In addition, the model can accurately predict the mill startup behavior for torque and mill power. This proves that the model is physically correct, and can be used for modeling large-scale mills.IntroductionUnderstanding of the charge motion within the mill is of importance in mill optimization. The breakage of ore particles and the wear of liners/ball media are closely linked to the charge motion. To study these phenomena in a physically correct manner, appropriate numerical models for different parts of the mill system must be used. Validation of these models is of major importance. This has led to an increased interest in obtaining an accurate and direct measurement of mill load and the behavior of the mill charge.For structural analysis, the finite element method (FEM) is the most developed and most frequently used numerical method. FEM is a numerical solution method based on continuum mechanics modeling. A constitutive relation for the actual material is described, and the governing equations are solved in Zienkiewicz and Taylor (2000). Varieties of different constitutive models for a large number of materials are implemented in modern FEM code. The computability of nonlinear problems in solid mechanics is investigated in Belytschko and Mish (2001), among others."

Jan 1, 2015

By Rita Aiello, Stan Mack, Peter Werth, Joseph McCarney, Jozef Stachulak

"Johnson Matthey has developed the first diesel particulate filter (DPF) for underground mining that controls particulate matter (PM) at the same time as maintaining emissions of NO2 at or below engine baseline levels. DPF technology is critical for controlling PM which is classified as a carcinogen, but passively regenerating systems rely on the use of oxidation catalysts that can potentially increase NO2 emissions. This paper reviews the development of low-NO2 PM control technology and the results from testing this technology underground on diesel mining equipment. KEYWORDS Decomposition catalyst, Diesel particulate filter (DPF), Diesel particulate matter, Mining Continuously Regenerating Trap (CRT®), NO2, SCR INTRODUCTION The introduction of diesel particulate filter (DPF) technology on heavy duty diesel (HDD) engines has been an important step towards addressing the clean air and health concerns for mining companies. Control of diesel particulate matter (PM) emitted from diesel engines is already being implemented for on- and off-road vehicles, and similar legislation is being prepared for mining equipment. In addition to PM, the diesel emission control strategies (DECS) also reduce carbon monoxide (CO) and hydrocarbons (HC). Some DECS control oxides of nitrogen, or NOx, which is composed of NO and NO2. Johnson Matthey has led the development of emission control technologies for diesel engines for almost 30 years. Over the last ten years alone JM has supplied over 3 million Continuously Regenerating Trap (CRT®) DPF systems for on-road vehicles, and over 200,000 systems for off-road vehicles. The patented CRT technology combines a diesel oxidation catalyst (DOC) with a DPF to effectively trap harmful PM from diesel exhaust, while removing CO and HC. The DOC converts part of the engine NOx to NO2, which reacts with the trapped soot to regenerate the filter. As engines become more fuel efficient, less waste heat enters the exhaust. This can be a disadvantage for after-treatment systems as it leads to lower catalyst operating temperatures. The CRT system regenerates passively, without addition of heat, at temperatures that are typical of diesel engine exhaust. JM recently launched the Mining CRT system which integrates CRT technology with NO2 abatement to reduce PM and tailpipe NO2 from underground diesel mining equipment. This is the first technology proven to control both PM and NO2 emissions for a cleaner, healthier working environment. The Mining CRT is also cost-effective compared to other technologies."

Jan 1, 2019

By C. R. Tang

Due to the current lack of sufficient occupational hazards supervisory staff in China, an occupational hazards supervision regulatory framework is proposed, based on the cloud. Data on respirable dust, noise, heat, toxic and hazardous substances and protection facilities are uploaded to private cloud computing data and service centers to build an occupational hazards supervision system. This system promotes occupational hazards governance. Complex reports are generated. Through the establishment of an occupational hazard supervision data threshold, the dynamic regulation of occupational hazards is accomplished. The main characteristics of this approach are low cost, ease of expansion and maintenance, and strong performance.

Aug 1, 2013

By Seth K. Martin, Tony Nichlany, Alan R. Poeppel, Konstantinos Syngros

"This paper presents a case study on bored pile construction in challenging karst conditions below a supertall building in Kuala Lumpur. Innovative design and construction techniques helped keep the project moving through very difficult and unpredictable geological and drilling conditions. The development encompasses about 12,400 square meters and includes a 77-story tower, a 59-story tower, a five-story podium, and four contiguous basement levels. The site is underlain by a residual soil derived from a siltstone/claystone (the Kenny Hill formation), then limestone bedrock. Subsurface conditions are relatively uniform within the Kenny Hill and highly variable at the limestone surface. Extreme cases included 40-meter-tall underground caverns, 40-meter-tall pinnacles, and a 50-meter-tall underground rock ledge. Local piling practice in Kuala Lumpur involves deriving pile capacity entirely in the Kenny Hill formation to avoid the unpredictable limestone surface. However, the massive tower foundation loads and relatively shallow bedrock required the piles to be socketed in the limestone. The 77-story tower will be supported by 2.0- and 2.2-meter-diameter bored piles 50 to 100+ meters long, socketed in limestone, with working loads between 40 and 70 Meganewtons. Two Osterberg-cell load tests were used to develop a site-specific rock socket skin friction correlation with RQD. Exploratory rock probes were drilled at each pile location to design the rock socket length based on the rock quality and sloping rock conditions. The rock mass was pressure-grouted during each rock probe to improve the rock quality and fill voids in the rock.INTRODUCTIONThe Kuala Lumpur City Centre, home of the Petronas Towers and the world’s deepest foundations, will be the future home of a new supertall tower. The 77-story tower will be supported by a piled-raft foundation that relies on piles terminating in the highly erratic, karstic Kuala Lumpur limestone formation. The high building loads coupled with relatively shallow limestone across the majority of the tower footprint forced the piles to extend into the limestone."

Jan 1, 2016

By Eleanor Abshire

[THE INCREASING use of hafnium as a vital component in atomic power reactors has brought this metal into recent prominence. A literature survey was made and this bibliography was compiled to provide research and production groups with a ready source of reference to this important metal anti its compounds. This service is rendered by the Zirconium Information Center, which is sponsored by the Department of the Navy, Bureau of Ships, and the F .S. Department of the Interior, Bureau of Mines, tit the Bureau's Northwest Electrodevelopment Experiment Station, Albany, Oreg. The following reference sources have been reviewed for this compilation : Chemical Abstracts; Industrial Arts Index; Crerar Metals Abstracts; Nuclear Sciences Abstracts; Bureau of Mine; Information Cicular 7771, Bibliography of Zirconium; anal Bureau of Mint' Information Circular 7830, Bibliography of Zirconium, suppllement to Information Circular 7771.]

Jan 1, 1960

By J. Aravena, S. Gajardo, M. Ayala, P. Salinas

Both, Teck Carmen de Andacollo (Teck CDA) and Orica, work hard in the implementation of new technologies available in the explosives industry and drilling and blasting techniques, with the objective of sustainable development of their operations, regeneration, and protection of the environment, also considering the welfare and relationship with the surrounding communities. The open-pit Carmen de Andacollo mine is located adjacent to the town of Andacollo. Therefore, both companies together have developed the implementation of different techniques and technologies to mitigate the impacts of mining operations in the community, considering an important part of this challenge to minimize the impact of their perception of blasting by reducing the level of vibrations and sound pressure (airblast), in addition to the control of dust and smoke, strengthening sustainable production in harmony with communities. The technologies and techniques that have been implemented are the installation of airblast and vibration monitoring stations stands out, whose database has records since 2011. Using the vibration database, different models were developed to predict the vibration level of blasting in its design phase, achieving a difference of 4.1% between the estimated and measured values in the last year. Two techniques stand out to minimize the ejection of material, "Hydraulic Dome" and "Dual layer blasting", the first consists of water irrigation on the surface to be blasted and the second is an unconventional blasting technique, which was awarded in 2015 for its results in the environment. Also pre-splitting engineering has been modified in a positive evolution, where through different configurations, the airblast has been reduced by 15% compared with records from 2011 to 2022. Finally, due to the impact of operational restrictions, such as days available to blast, number of holes, and powder factors, the wireless initiation technology was implemented, which allowed reducing the limitations in the loading, generating an improvement in terms of blasted materials over conventional systems. Understanding the restrictions and challenges in terms of impact on communities, the correct implementation of all these techniques is important, and in conjunction with collaborative work, it has been shown and validated that producing in a sustainable and sustainable manner is possible.

Jan 1, 2024

By Mark S. Sanders

Six underground coal mine shuttle cars (three high seam and three low seam) were used to assess visibility using the concept of visual attention locations (VALs) and an improved human eye reference measurement instrument (HERMI Mark II). Each machine was assessed in the inby and outby direction of travel with no canopy and with the canopy in its highest, and lowest position. In addition, the illumination level at each VAL was determined. Results showed that the most important variable determining visibility was operator eye position. When this variable is controlled, the addition of a canopy has no effect on visibility. Further, with eye position controlled, there is no difference in visibility between high and low seam machines. The visibility and illumination assessments found blind spots in the operator's field of view located on the opposite side of the car from the operator and ahead of the machine. Suggestions for reducing the blind spots were made. The report also included a procedure manual for using HERMI and the system of VALs to assess visibility from underground shuttle cars, continuous miners, and scoops.

Jan 1, 1983

By S. J. Page, P. Bolsaitls, W. E. Wallace, C. A. Hill, M. J. Keane

"Boiling respirable quartz dust in water for 10 to 40 minutes decreases the cytotoxicity for both erythrocyte hemolytic potential and pulmonary macrophage release of lactate dehydrogenase in vitro. The potential is reduced to near zero in the boiling concentration range of 1 to 10 mg quartz per ml water in boiling times of 20 to 40 minutes. Below this range the detoxification occurs over a longer boiling time. Above this range the hemolytic potential remaining after 40 minutes of boiling approaches native quartz potential with increasing concentration up to 30 mg quartz per ml water. Replacing the media with fresh at the midpoint of boiling results in full detoxification through 20 mg per ml. Pre—boiling the medium with quartz or silica gel reduces the effect of subsequently boiling test samples. Detoxification persists after mild drying at 110 C for 8 hours, and persists after three days of resuspension in water at room temperature. Additional data on persistence of the effect, on the use of acidic and basic media treatment, and on surface analyses are presented, with a discussion of a working hypothesis and research needs.IntroductionResearch underway to determine interactions of quarts and other mineral dust surfaces with pulmonary fluids and alveolar macrophages in culture led to the observation that when dusts were autoclaved in aqueous suspension, their cytotoxic effects on macrophages wore suppressed, in some cases fully and even after several days incubation with the cells. This finding was in direct contradiction to earlier results from both short term macrophage lysosaal enzyme release assays, as well as longer term cytotoxicity assays from macrophages in culture; in those studies, dusts were steam autoclaved at 121 121 ºC with no liquid water but with steam present. (1,2) However detoxification under boiling conditions has been reported in other research.(3). It was decided to use the hemolysis assay to further investigate these findings, because of its sensitivity, simplicity and cost."

Jan 1, 1988

By F. G. Scott

This document is a proposed program plan for mining environmental research to be conducted by the U.S. Bureau of Mines in support of industrial oil shale mining and processing. This program plan is one of three research alternatives being considered by the Bureau, each based on a different level of anticipated funding. This report documents the low funding level program plan.

Jan 1, 1980

By Amilton Ferreira de Oliveira

Este trabalho se propõe a mostrar os resultados obtidos pela SunCoke Energy Brasil após as mudanças do perfil da mistura de carvões, na qual foram acrescidas criteriosamente as participações dos carvões denominados “soft” e carvões “steam coal”, seguido da redução também criteriosa dos carvões médio voláteis. A consolidação dos dados de qualidade do coque e do custo das misturas comprova que as modificações no perfil das misturas foram bem sucedidas, pois a qualidade do coque se manteve conforme a expectativa dos clientes (Altos-Fornos) e o custo das misturas apresentou uma significativa redução. Todos os testes e experimentos adotados foram embasados na utilização na metodologia denominada “Método e aparelho para avaliar as propriedades de coqueificação do carvão”, também conhecida como Box Test, e ainda no profundo estudo das características dos carvões utilizados e os impactos destes na qualidade do coque.

Aug 16, 2017

By James P. Bennett, Jinichiro Nakano, Anna Nakano, Hani Abu El Hawa

Carbon feedstocks used in power, chemical and metallurgical industries typically contain numerous minerals or impurities that liquefy during high temperature processing to form slag as a byproduct. Slags have many industrial applications, for example, as construction materials and for element recovery. In addition to other variables, the extent of slag utilization is dependent on its com- position and post treatments. In this work, the in fluence of temperature and phos- phorus additions on phase evolution in coal slag was investigated. Synthetic slag mixtures with varying AlPO4 contents (0–14 wt%) were heated from 1380–1470 ° C in air, then water-quenched to preserve the phases formed. SEM/EDS, XRF and XRD analyses were performed before/after testing to gain insight about slag chemistry and phases present. It was found that coal slag exhibited a large solubility of phosphorous, affecting morphology of mullite formed under the conditions studied. Results obtained and their significance are discussed.

Mar 1, 2017

By Longjiang Li, Mao Jiang, Zhihui Shen, Guizhou University, Yin Pan

This paper aims to study the influence and action mechanism of collector Y-89 on the flotation of auriferous pyrite. The measurement to identify adsorption quantity, IR and XPS spectrum analysis and flotation experiment made on the pure mineral were conducted. The research results show that when the dosage of MIBC is 20 mg/L, and pH of 8, the dosage of Y-89 over 60 mg/L, the pyrite recovery rate is greater than 80%.And when the dosage of Y-89is 60 mg/L, dosage of MIBC 20 mg/L, the pH in a wider range (pH=4~9), the recovery is greater than 75%. When the pH is above 10, the pyrite is depressed and its recovery rate is found to be dramatically dropping. Adsorption quantity measurement also shows that the strong alkaline conditions inhibit the adsorption of Y-89 on the surface of auriferous pyrite. IR measurement indicates that chemisorption of Y-89 occurs on the surface of auriferous pyrite. XPS spectrum analysis indicates that without adding Y-89, oxidation reaction occurs on the surface of pyrite. But when Y-89 is added, the chemical environment of Fe on the surface of pyrite has changed. Such findings indicate that with Y-89, chemisorption occurs on the surface of auriferous pyrite.

Jan 1, 2014

By Jorge Gibson, P. Chris Pistorius, Megha Jampani

Increased utilization of natural gas in blast furnace ironmaking can decrease both the cost and the carbon intensity of ironmaking, given current US natural gas prices. In this paper, three ways to utilize natural gas are compared: tuyère injection, prereduction of iron ore, and shaft injection. The basis for comparison includes coke replacement ratios, carbon intensity and furnace productivity. These were calculated using relevant mass and energy balances, a blast furnace productivity correlation based on the bosh gas flow rate, and measured and modeled prereduction kinetics. Of the natural gas utilization methods, prereduction has the highest effective coke replacement ratio (and hence the largest advantage in raw material cost), but is likely to have the highest capital requirement.

Mar 1, 2017

By Russell L. Cook

Stringent environmental regulations, which have limited the use of sludge ponds, coupled with the economic incentive to clean more 'coal or to add fine coal cleaning additions to existing preparation plants have increased the use of static thickeners in preparation plants. The Lamella Gravity Settler, sometimes de signated Lamella Thickener, is a shallow depth sedimentation device which has been applied in a variety of industrial process and wastewater control projects in place of the conventional raked thickeners. This paper presents the theory and design of the La-mella Thickener, as well as describing the operating results from several full scale installations in a variety of Appalachian preparation plants.

Jan 1, 1977

By T Clemens, D Trumm

Adopting environmentally acceptable practices in New Zealand is a crucial requirement for mineral wealth development. Recent planned expansions in the coal industry have increasingly placed mining in the media spotlight. A lack of appropriate national environmental guidelines has resulted in inconsistent responses and assessments of current and prospective mine sites. Such inconsistencies have lead to delays in decisions on developing economic mineral deposits that may have only minor short-term impacts, and have also allowed unacceptable environmental management practices to continue elsewhere.   A research collaboration between CRL Energy, Landcare Research, University of Canterbury and University of Otago aims to provide regulator groups and the mining industry with a unified approach to the requirements of the Resource Management Act 1991, which is the legislation that predominantly drives the nationÆs environmental policies and guidelines. The tangible outcome of this research programme will be guidelines for an integrated decision-making framework based upon robust multidisciplinary science. The result of this unified process will facilitate the development of viable mineral deposits and prevent excessive environmental impacts.   The framework will be derived from a synthesis of four objectives. Objective 1 identifies potential water quality impact. This objective is based on a targeted geochemical study of the lithology and waterways of the West Coast and Southland. Objective 2 categorises the degree of impacts on the ecology of receiving aquatic ecosystems and determines the processes that drive aquatic ecosystem recovery. Objective 3 identifies best strategies to sufficiently manage impacted ecosystems, and to prevent future unacceptable impacts. Objective 4 combines the findings of Objectives 1 - 3 into a standard decision-making framework. The development of this framework development will include wide consultation with representatives of the mining industry and regulator groups. It is anticipated that this multidisciplinary approach will provide a robust and coherent, standardised system that will assist in achieving industry and environmental targets.

Jan 1, 2004