Search Documents

By D. L. Madge

The text of this chapter was not received in time for printing.

Jan 1, 1979

By Ryan Lemmon

Belt turnovers are commonly used in conveyors to rotate the belt so that the clean side of the belt contacts the return idlers. The belt turnover length has traditionally been sized on only the twisting stresses. However, belt turnovers are also subjected to bending stresses due to the weight of the belt. Although bending stresses have in the past been ignored, these stresses are significant and should not be neglected. This paper quantifies and presents a method for calculated twisting and bending stresses and also the belt sag.

Jan 1, 2002

By C. H. Pishny, Raymond M. Carr, E. J. Dickinson

Petroleum development in Oklahoma during the year 1932 was rather colorless. The crude price structure, while it was relatively stable, was too low to encourage wildcat drilling and proration restrictions were such that producing wildcats were usually faced with the drab prospect of being limited to 50 bbl. per day. Proration in flush and semiflush areas was for the most part successfully accomplished. Military enforcement of proration rulings was deemed necessary at Oklahoma City. The trend toward cost cutting and abandonment of unprofitable wells continued through the year. It is estimated that 1500 wells were abandoned and it is not unlikely that as many more were shut down which will never produce again. Oklahoma crude oil stocks were reduced by approximately 11 million barrels in 1932. It is generally conceded that inventories of material have been appreciably reduced. Leasing activity was limited principally to rental reductions and to close scrutiny of all lease holdings. There were numerous "leasing plays" based on geophysical information but with few exceptions they were small. It is estimated that over 15 per cent of the acreage under lease at the beginning of 1932 was surrendered during the year. There was a tendency through the year to prospect shallow pay sands formerly passed by in the search for deeper production. This is especially true of the Seminole area, where the Calvin sand received considerable attention, and where some good wells were completed. Prices There were two price changes during the year that affected the majority of crude sales. Using 36 gravity A.P.I. as a basis of comparison, the price was increased on April 11 from $0.77 to $0.92. On Dec. 16, the price dropped to $0.69. During the fall months there were several postings higher than this schedule but all postings were at the same level at the end of the year.

Jan 1, 1933

By Orlando Guerreiro Meira

A utilização de revestimentos com aços inoxidáveis superausteníticos em substituição às ligas a base de níquel na indústria de óleo e gás pode ser uma alternativa interessante, uma vez que é possível a manutenção de bom desempenho e corrosão com um menor custo. O presente trabalha avalia as propriedades mecânicas e microestruturais de revestimentos depositados com a liga AISI 904L sobre o aço carbono ASTM A 516 pelo processo eletroescória, tanto na condição de como soldado quanto após tratamento térmico de alívio de tensões. Após a soldagem, foram realizados ensaios mecânicos e metalográficos para verificar o efeito do ciclo térmico de soldagem nas propriedades do revestimento. O ensaio de dobramento não mostrou indicação de defeitos, sendo considerado aprovado. Os ensaios de microdureza apresentaram valores inferiores a 300HV0.5, em decorrência da microestrutura austenítica com baixo percentual de fases secundárias no metal de solda e de bainita na ZTA. O tratamento térmico de alívio de tensões não provocou mudanças significativas nas propriedades do revestimento

Aug 17, 2017

By Carolina Conter Elgert

A influência dos parâmetros termomecânicos e da adição de elementos microligantes na relação processo, microestrutura e propriedades de chapas laminadas, do aço DIN 20MnCr5 foi o objetivo de estudo deste trabalho. Os testes foram desenvolvidos em escala piloto, no laboratório de processos metalúrgicos do IPT. Foram testadas variações de composição química, condições de laminação e taxas de resfriamento. Ocorreu alongamento dos grãos austeníticos para os materiais processados por laminação termomecânica e refino de grão e aumento de limite de escoamento para os aços microligados, tanto na condição de laminação convencional, quanto na condição de laminação termomecânica.

Oct 30, 2017

By Gilbert P. Moore

Bolivia does not yet have any production which is being marketed. It does have a potential production, however, from wells which have been completed by the Standard Oil Co. of Bolivia, a subsidiary of the Standard Oil Co. of New Jersey. No other company is active in drilling and development work to date. The total potential production from wells now completed is about 6000 bbl, daily. Wells Completed Completions during 1928 and their initial daily productions. if any, were as follows: Camatindi No. 1, 350 to 1000 bbl.: Camiri No. 1, 500 bbl.; Sanandita No. 3, 100 bbl.; Tatarenda No. 1, dry hole, and Bermejo No. 2, deepened 50 ft. made 1000 barrels. The most striking development of the year was the Camiri No. 1 well which, after just entering the sand, made 500 bbl. per day of 52" B. oil. This well is the northernmost good producer which the Standard has brought in to date. Oil from this well is used without refining in the tractors and trucks of the company. A small topping plant has been installed from which high-grade gasoline is obtained for use in motor cars and some is being produced for the use of air plants stationed at Villa Montes. The results for Sanandita No. 13 were somewhat disappointing since Sanandita No. 2 was rated at about 3000 bbl. Tatarenda NO. 1, located on a large unbroken structure, was drilled to 4000 ft. and abandoned as a dry hole. Bermejo No. 2 was deepened 50 ft. to 2085 ft.. and on a 10-day test averaged 1000 bbl. per day. This well is on the border between Bolivia and the Argentine. Wells Drilling The wells drilling are Camiri No. 2, Sanandita No. 5, Machareti No. I and Bermejo No. 5. This is the smallest number of drilling wells which the Standard has had for several years but is principally due to

Jan 1, 1929

The largest investment in mining equipment in Caterpillar?s history ? The F series mechanical and electrical drive trucks ? is rapidly advancing. Caterpillar showcased the 793F and 797F mechanical drive trucks and the 795F ac electric drive truck at MinExpo in 2008 and have continued testing since then. The 793F and the 797F have accumulated more than 75,000 hours of field testing and have proven their performance capabilities and their durability. The new Cat C175 engine that powers them has racked up 130,000 hours of field testing in mining trucks and more than 120,000 hours in power systems. Because of the success of these field-follow programs, the 793F is targeted to go into full production within a few months and the 797F late this year. Caterpillar engineers have been testing two 795F ac prototypes at the Tucson Proving Grounds in Arizona. The development program has provided input for the construction of a new 795F ac in Decatur, IL. The new truck recently shipped to a copper mine in North America where it will serve as the first field-follow 795F ac as it works at the mine. The 313-t- (345-st-) capacity 795F ac will enter a new size class for Caterpillar, and, as a result, the primary focus of the Caterpillar ac electric program has been on the 795F ac. The commercial launch date will be defined as the field-follow program progresses. ?It?s fitting that soon after producing the 50,000th Cat off-highway truck, we are now shipping our first ultra-class ac electric drive truck to a mine,? said Chris Curfman, president of Caterpillar Global Mining. ?Our new trucks further solidify our position as the one manufacturer to provide unparalleled options and unmatched customer support.?

Jan 1, 2009

By C. N. Bensley, S. K. Nicol

The major developments in fine coal processing in Australia are reviewed. Emphasis is placed on the approaches taken by various Australian coal producers to improve the recovery of the coarse size fractions (minus 0.5 plus 0.25mm) and upgrade the selectivity of flotation at ultrafine sizes (minus 0.075mm). The effects on fine coal preparation of flotation circuit changes, the influence of physical and chemical variables on coarse coal flotation and the impact of spiral concentrators and column flotation, are discussed. Reference is also made to the development of oil agglomeration technology for the treatment of fine coal refuse and some of the factors which have led to its current demise.

Jan 1, 1988

By R. E. Kennedy

"INTRODUCTION In a previous publication4 results were given of numerous experiments made on the in-flammability of gas mixtures consisting of methane, hydro a. carbon monoxide, nitrogen, and carbon dioxide. Data were obtained and tables prepared giving the inflammable limits of each of these combustibles when mixed with various proportions of carbon dioxide and nitrogen. By the use of these data and the application of Le Chatelier's law, it was found possible to calculate the limits of inflammability of any gas mixture containing any or all of the above gases.Various mixtures of the five gases given above were prepared and their limits determined experimentally and then calculated. Good agreement was found between the determined and calculated results when complex gases encountered in mine safety work were tested. Of special significance was the accurate calculation of the limits of inflammability of gases from mine fires, gases from mine explosions, detonation products of explosives, blast—furnace gases, automobile exhaust gas, and other gases of a similar character.Using the method given in the above report, Yeaw5 investigated a number of industrial gases including oven, coal, producer, blue, carbureted blue, and dry quencher gases, and found the determined and calculated results to agree remarkably well, thus giving further proof of the value of such a means of determining dangerous conditions when combustible gases are encountered in practice.GASES FROM A POTASH MINEGases were recently encountered in a potash nine in New Mexico, containing the com-bustibles, methane, hydrogen, and ethane. In one special case a mild explosion occurred when these gases were mixed with the right proportions of air and ignited it therefore became necessary to know the inflammability of these mixtures in order that the proper precautions could be taken to prevent explosions."

May 1, 1932

By Steve Tadolini

Underground roof falls can have devastating effects on the safety of operations personnel, and equipment, and seriously impact production. Immediate steps are usually taken to danger off and secure the area while clean-up efforts are designed and implemented. A critical step, often overlooked due to production demand, is the determination of - why the roof fall occurred so that additional occurrences can be avoided in future developments or what measures can be taken to identify areas that have similar ?symptoms?? Forensic engineering includes the investigation of materials, products, structures or components that fail or do not operate/function as intended. The authors define forensics in ground control engineering as the study of evidence discovered while examining underground roof falls by applying expert observational techniques and established mining engineering principles to determine the probable cause, hypothesize solutions, and design engineering safeguards to prevent reoccurrences. Simply stated, the primary steps in the forensics of underground roof fall techniques are: ? Assess regional and local conditions prior to the event. ? Assess post-event conditions. ? Hypothesize plausible ways in which the pre-event conditions ? became the post-event conditions.Search for evidence that either denies or supports the various ? hypotheses.Apply engineering skill to relate the various facts and evidence into a cohesive scenario of how the event may have occurred. This paper details the proposed technique by utilizing a roof fall case study that required the examination of five primary factors: mine design parameters, excavation geology, method of excavation, method of support, and mining cycle times.

Jan 1, 2009

Tougher physical mining and processing conditions as well as economic circumstances are causing many mining companies to re-evaluate the effectiveness of their mine planning. The recent wave of inexpensive computing power provides the engineer an opportunity to go beyond the simple one-off manual mine design and production schedule. The basis of a good mine plan is a good reserves model. Concepts of mine model development are explored. The only advanced computer methods that have found consistent success in optimising mine planning functions are economic pit limits determination and material scheduling. Three pit 'optimisation' methods are examined; the moving cone, the Lerchs-Grossman 3-D graph algorithm, and the new network flow algorithm. A comparison between the methods in terms of total profits generated and computer time involved are made. The results show that both algorithms produced a higher profitability than the simple moving cone, but at much higher execution times. However, the profit increase never exceeded much more than 1 % of the base moving cone case. Finally, a method for the development of long range material production schedules with forward waste planning is presented.

Jan 1, 1989

By James M. Winston

When I began my career (the first assignment was mucking the "drainage" ditch) an experienced miner told me, "Remember son, happiness is a journey, not a destination. . . ." If you missed the 100th Anniversary of AIME in New York this year, you are missing the journey. There are not enough superlatives to describe the event. Especially since New York is "known to have it all." An Indefinable Plus There was a little something different at this meeting. I cannot explain what, but there seemed to be more of everything. There were more wives there this year-what a pleasure to see all the lovely women mingling through the conference- which was reflected through our own attire and mannerisms. In fact, everyone looked so great, we checked to see if it really was a convention of miners. You wives keep coming to all of the events, because so much is added by your presence.

Jan 1, 1971

By Sheng-Hui X

This paper introduces a new coal-based rotary kiln process of DRI production - the CRIMM process, which is developed by Changsha Research Institute of Mining and Metallurgy in the past years. Its main features are the use of composite pellets (in rotary kiln). The process consists of preparation of pellets from iron concentrate and coating of coal on their surfaces. The new process is able to overcome a series of defects of the conventional coal-based rotary kiln processes. A continuous test was conducted using an experiment rotary kiln (-0.6;, x 3 m). TFe of the magnetic iron concentrate used in the test is 67.25 per cent. TFe of the product DRI is 88.54 per cent, MFe is 84.11 per cent, S and P are less than 0.02 per cent. The metallisation ratio of pellet is 95 per cent. The pellet power ratio is less than 0.3 per cent. The utilisation coefficient of rotary kiln is 1.3 t/m'-d. The overall recovery of iron concentrates is 99.7 per cent. Two small industrial plants using the CRIMM process are being set up in China. Their coal consumption can be decreased to 520 kg standard coal per ton DRI respectively.

Jan 1, 1999

By E. K. Stanek

The field tests involved ten coal mines in which transients were initiated on the dc system from which the parameters of the dc mine electrical power system could be determined. The data processing involved the use of a Fourier Analyzer to filter noise and fit an exponential curve to the field waveforms. From this data analysis it was possible to find the dc system resistance, inductance and time constant. The survey of nationally recognized laboratories was conducted to establish that the recommended test criteria were practical. The development of test criteria for dc fuses used in mines was based on the measurement of parameters in the field, the survey of testing laboratories, literature searches, laboratory test, etc. A computer program was written to analytically predict the parameters measured in the field. This approach has limitations but reasonable agreement with field results was obtained. A brief laboratory testing program was carried out to verify the practicality of the recommended criteria and establish the accuracy of the conclusions concerning dc fuse performance.

Jan 1, 1984

By Ángel Fernández

En Minera Coimolache se generan aproximadamente 700 t de residuos sólidos al año. El 50% de estos corresponde a residuos orgánicos, los que mediante fermentación anaeróbica con microorganismos eficaces son transformados en un plazo muy breve en bioabonos sólidos y líquidos (solución ecológica). Los microrganismos eficaces presentes en estos bioabonos han mejorado notablemente los procesos de siembra, incrementando hasta en un 361% la densidad poblacional de la misma. Por otro lado, dado que la actividad microbiana generada compite por el oxígeno del suelo reduciendo de forma colateral la generación de drenaje ácido de roca (el pH incrementó de 2.02 a 7.55 y se redujeron metales como el Fe, Pb, Cu y Zn), se ha obtenido una solución económica al emplear suelos abonados, como sustituto de la cal, para la cobertura de depósitos en proceso de cierre.

Jul 30, 2018

By Jetson Lemos Ferreira

A Usiminas vem procurando fornecer aços de menor espessura ao mercado automotivo, com graus de resistência cada vez mais elevados, destacando-se os Advanced High Strength Steels (AHSS). Contudo, até então, a aplicação desses aços tem sido destinada basicamente em aplicações em peças de segurança e de reforço estrutural dos veículos. Visou-se nesse estudo avaliar, em escala laboratorial, a aplicabilidade em painel exposto de um AHSS referente ao grau DP450 em termos de conformabilidade e de desempenho, tendo como referência aços Interstitial Free (EC180) e Interstitial Free High Strength (IFHSS220). Foi verificado que o aço DP450 apresenta características mecânicas favoráveis ao processo de estampagem de componentes automotivos expostos. Para fatores que podem limitar sua utilização, tais como a flangeabilidade e o retorno elástico, foram propostas alternativas de processamento, as quais resultaram na maximização da conformabilidade do material e em melhor fixação de forma. Em termos de aplicação, verificou-se que o aço DP450 exibiu uma resistência à indentação, avaliada pela profundidade da impressão permanente, em torno de 43% e 31% superior à dos aços EC180 e IFHSS220, respectivamente.

Aug 17, 2017

By Amanda de Angelis Vitoi

A nitretação do aço inoxidável endurecível por precipitação do tipo 17-4PH foi estudada comparativamente pelos processos de Plasma-DC e de Tela Ativa. Os resultados mostram que os dois processos são eficientes em promover a formação da camada nitretada de elevada dureza superficial, cerca de 1300 HV0,025. Entretanto, diferenças importantes são observadas. No processo de Plasma-DC a camada nitretada é composta, além da martensita acicular saturada em nitrogênio, de nitretos de ferro e cromo precipitados pela supersaturação. No processo de Tela Ativa a precipitação de nitretos de cromo é praticamente suprimida e predominando os nitretos de ferro. Esta diferença na sequência de precipitação de nitretos é inferida como sendo causada pela oferta de nitrogênio. Em Plasma-DC a oferta de nitrogênio é suficiente para a precipitação do nitreto de cromo, o que não ocorre em Tela Ativa. A maior profundidade de camada e de endurecimento transversal confirma a maior difusão de nitrogênio em Plasma-DC. Ainda, em ambos os processos a dureza de partida do substrato envelhecido é preservada após o ciclo de nitretação.

Aug 16, 2017

By Flávio Parreiras Marques

A microabrasão é uma técnica para produzir desgaste abrasivo em escala micrométrica. Neste trabalho estudamos uma liga fundida de cobalto com composição química próxima à da superliga comercial Stellite 6com composição eutética sendo a matriz constituída por uma solução sólida de cobalto, cromo e molibdênio que embebe uma grande quantidade carbonetos eutéticos de cromo. O objetivo deste estudo é avaliar a resistência ao desgaste bem como os micromecanismos dominantes através de ensaios de microabrasão. Foram usados três diferentes tipos de lama abrasiva, sílica, alumina e carbeto de silício com uma concentração de 0,1 g/cm3, carga de 0,3 N e uma distância deslizada de 48 metros. O menor coeficiente de desgaste foi obtido com sílica e o maior com carbeto de silício. O micromecanismo dominante foi o riscamento com riscos em toda superfície da amostra e presença de indentações apenas na matriz.

Aug 16, 2017

By Shuji Owada

Scrap electrical and electronic appliances, so called "E-waste", are not a present target to be collected and recycled under Japanese regulations. This material, however, contains considerable amounts of base, precious, and rare metals and it is necessary to recover these elements for maintaining stable supply and establishing "the society of environmentally-sound material-cycle". This paper describes recent trends of rare metals recycling in Japan and technological approaches to achieve the above objective. Also a research work to concentrate rare metals from the printed wiring boards by combining brand new comminution and physical separation methods is discussed.

Jan 1, 2011

By D. Michael Holloway

The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the structures along the realignment of Interstate 880. The project replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers well beyond local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata and quantifying the effects of installation on the long-term capacities of the piles led Caltrans to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1995