Search Documents

By Mark F. Sindelar, Yi Luo, Hua Jiang, Michael T. Shook

"Convergence of roof and floor in underground mine openings is a common occurrence. This convergence not only adversely affects the ability of workers, equipment and supplies to travel through the mine, it also reduces the effectiveness of the mine ventilation system, which is essential for the dilution of methane gas and airborne respirable dust. While installing secondary standing supports to control floor and roof convergence, such supports, by nature, partially obstruct a portion of the airway. These added obstructions inhibit the ability of the ventilation system to operate as efficiently as it could by increasing the resistance in and reducing the cross-sectional area of the airway.This study introduces and demonstrates the benefits of The Eye CAN™ standing roof support, which controls floor and roof convergence and is less obstructive to air flow than conventional wooden cribs. Laboratory findings show that the normal resistance of a supported lined airway is reduced by using this new product from Burrell Mining Products, Inc., while providing the same roof support characteristics of an established product-The CAN®. Load vs. displacement curves generated from laboratory tests demonstrated that this new product behaves with the same roof support characteristics as others in The CAN product family. Ventilation data gathered from a simulated mine entry was then used for computational fluid dynamics (CFD) modeling. The CFD analysis showed an improvement with The Eye CAN versus other accepted forms of standing roof support.This proof-of-concept study suggests that, when using this new product made by Burrell Mining Products, Inc., not only will the convergence from the roof and floor be controlled, but airway resistance will also be reduced.INTRODUCTIONOne of the basic elements of underground mining is the necessity to support the mine roof. It is well-known that easier reserves have been mined so that today's underground mines present challenging conditions. Factors influencing roof support decisions include mine depth, mining method, overburden composition, and agency regulations. Mining engineers, therefore, have to balance three objectives: safety, engineering, and cost. While safety is obviously paramount, and engineering often complements safety, the cost effectiveness of any product, method, or device warrants additional consideration in today's harsh business climate. Avenues for adaptation and improvement are found at the intersection of the three objectives."

Jan 1, 2016

By J Rock, K Bambrook

"Hanwha Mining Services was approached by Glencore Coal to provide a series of (trial) demonstration blasts at its Clermont coalmine. The intent of the project was to trial a bulk explosive product that would be able to provide sufficient energy for the ground type encountered without production of post-blast fume. Three blasts were loaded using the patented XLOAD bulk explosives with a density of 1.00 g/cc. XLOAD bulk products are water resistant explosives that can be loaded at densities much lower than traditional (generic) water resistant heavy ammonium nitrate – fuel oil (ANFO) or pumped blends with significantly reduced risk of fume. In addition, these products have detonation characteristics that generally deliver a higher heave partition than conventional bulk products and hence improve muck pile looseness and digability.The priority key performance measures included the absence of fume from blasting, being at least cost neutral and providing similar if not improved shovel dig rates. The design for the initial blast took a conservative approach to ensure the key blast outcomes of fume control and fragmentation were achieved.The second blast used the same pattern dimensions as the benchmark bulk product used in this area to provide a cost neutral comparison with the benchmark products that had been used over the prior six months. This resulted in a 20 per cent lower powder factor than would have otherwise been used. To test the suitability of XLOAD, this shot was slept for over two weeks between loading and firing in geology where the sleep time is typically kept to a few days to minimise the fume risk.The third blast utilised a slightly larger drill pattern to push the capabilities of XLOAD and provide a cost neutral comparison between the trial product and the traditional benchmark products. All three blasts were fired with no fume observed, no recordable incidents and good fragmentation. Shovel productivity from all three of the trial blasts was excellent with higher average instantaneous dig rates being recorded (average six per cent improvement against the instantaneous dig rates recorded for the benchmark blasts).Citation:Rock, J and Bambrook, K, 2016. Controlling Blast Related Fumes with Unconventional Explosives, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By William A. Beck

The K.T. Dome Mine in Owen and Henry Counties, Ky., has been operated intermittently under several different owners since the early nineteen hundreds. No record of total production is available, but it is said that during 1943 and 1944, while being operated by the Twin Valley Mining Co., 30 cars of zinc concentrates and 10 cars of lead concentrates were shipped. The vein can be traced for about 10 miles along the strike from Lockport, Henry County, to Big Twin Creek in Owen County. It pinches and swells both vertically and horizontally and is reported to average 20 inches in width. In order to develop additional reserves on the property, the Bureau of Mines drilled four holes on the south extension of the vein. Drilling disclosed that the vein dips to the west on the south side of the Kentucky River and is continuous along the strike and in depth. However, the extent of mineralization in the vein varies widely.

Jan 1, 1949

It is a common misconception that the grant of mining tenure, whether it be an Exploration Permit, Mineral Development Licence or Mining Lease, will entitle the holder to access all land within it in order to explore or mine. The ability for miners to access their tenure in order to undertake activities is critical to the industry. While significant time and energy is quite rightly dedicated to resolving native title and cultural heritage issues before the commencement of mining operations, the same cannot always be said for addressing potential impediments that arise as a result of the overlap between mining and other tenures. Miners should be aware of the overlaps that occur with other tenure and the impact of these overlaps on the minerÆs ability to explore or produce from the area. The existence of an overlap with petroleum tenure, nature refuges, national parks, wild river areas or reserves such as aboriginal land leases are all likely to have an impact on the minerÆs ability to access the area and conduct activities. In some instances, such as an overlap with petroleum tenure, Queensland legislation encourages the miner to reach agreement with the holders of the overlapping tenure. However, in other instances, such as an overlap with a national park, mining tenure is unlikely to be granted at all. This paper summarises the impacts and impediments that arise as a result of overlaps of tenure that are likely to affect mining operations. It also provides examples of how these impediments can, if possible, be overcome under Queensland legislation.

Jan 1, 2007

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTIONThe process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic.A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities."

Jan 1, 2012

By A. McGrath, M. Trovant, M. Haque

Minimizing energy consumption is a priority for many industrial facilities. Metallurgical and gasification processes produce dirty syngas (CO and H2), which offers the potential for energy recovery. However, syngas handling can pose an explosion risk and even minor leaks can result in poor workplace hygiene. Furthermore, many jurisdictions around the world now discourage wet syngas handling due to limited water availability and secondary pollution. Hatch has developed a 100% positive pressure gas handling system that targets these safety hazards without using fresh water. The implementation of a system for calcium carbide smelters at Qinghai Salt Lake Industry Co. (QSLIC) in China is profiled as a case study.

Jan 1, 2015

By J. Noll, C. DeGennaro, C. Zhou, J. Srednicki

"The personal dust monitor (PDM) (model PDM3700), as well as other electronic devices, can cause electromagnetic interference (EMI) which can disrupt the operation of some proximity detection systems (PDSs). A 15 cm (6 inch) minimum separation distance between the miner-wearable component (MWC) of the PDS and the electronic device usually avoids these disruptions, but due to the amount of equipment on a miner’s belt and the method of wearing the PDM in some situations, this distance can be difficult to always reliably maintain. Another method of reducing EMI effects is utilizing magnetic field shielding. The shielding capability of several different materials was investigated by surrounding the PDM with the material and quantifying the EMI. A copper mesh pouch reduced the EMI from a PDM3700, allowing a minimum separation distance of 10 cm (4 inches) instead of 15 cm (6 inches) as shown in a previous study for an unshielded PDM. A MU-metal box had a better shielding effectiveness, as it further reduced the minimum separation distance to less than 7 cm (2.8 inches). Shielding reduced the EMI of the PDM with MU-metal providing better results than the copper mesh. These materials may be beneficial for shielding individual components of the PDM or for constructing a shielded pouch. However, before the advantages of a shielded pouch can be determined, the effects of just the shielding material (metal) on the PDS needs to be quantified. INTRODUCTION According to statistics from the Mine Safety and Health Administration (MSHA), 43 miners have been fatally struck or pinned by a continuous mining machine (CMM) since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems (PDSs) have been developed and are required on all operating CMMs in underground coal mines, with the exception of full-face CMMs, by 2018 (MSHA, 2015)."

Jan 1, 2018

By Basilio Giurgola, Jeremiah M. Jezerski, Filippo Azzara, Federico Bonaiuti, Russell H. Lutch

The Northeast Boundary Tunnel Project consists of a 23 ft diameter, 27,000 ft long, CSO tunnel, multiple underground connections, and significant surface works within an urban corridor. The NEBT alignment depths range from 60 to 140 ft and includes seven shafts ranging in depth from 77 to 155 ft with diameters varying from about 19.5 to 56 ft, some as in-line connections and others required adits for connection to the main tunnel. This paper focuses on the design and construction of two major underground connections which are the First Street Connector Tunnel and the Mount Olivet Road Diversion Sewer.

Jun 13, 2023

By H. A. Baumann

Experimental data are presented showing the influence of size consist and firing rate upon the performance of bituminous coal-fired, single-retort, industrial underfeed stokers. Size segregation, degradation, and distributor data are also included. The conclusion is reached that size consist of the fuel as fired, is a critical factor in its performance on this class of equipment.

Jan 1, 1950

By K. Kar, A. Sreeoath, M. Gautam

"This paper presents results of an experimental investigation of the sampling efficiency of a blunt cylindrical sampler oriented with respect to the oncoming flow. The number of particles sampled by the cylindrical blunt sampler and an isokinetic sampler is measured using the TSI Aerodynamic Particle Sizer. A technique is described to conven the ratio of the particles sampled into the sampling efficiency. The experimental data thus obtained is then compared with the impaction model of Vincent and Mark (1982) with the empirical constant determined from our experiment.. The comparison shows excellent agreement for 0° and 90° orientation.1.0 IntroductionCylindrical dust samplers are widely used in practice to determine the concentration of the airborne particulate matter. The sampler is simply a means to collect particles from the ambient, whose concentration is subsequently measured by some size selective techniques. Gravimetric and optical techniques are the two most commonly used methods to measure the particle sizes. While impactors are used in gravimetric analysis, Aerodynamic Particle Sizer, Aerosizer. Electron microscope, Coulter Counter etc. use the optical method to measure the particle sizes. The Aerodynamic Particle Sizer (APS) and the Aerosizer are the new generation devices which employ the time of flight of particles within intersecting laser beams to determine the particle size.The introduction of the sampler in the free stream disturbs the flow pattern due to two distinct actions of the sampler on the fluid stream: one of them results due to the conformity of the flow to the geometry of the circular cylinder and the second one is caused by the flow into the suction orifice. If the sampler performance is determined by the number of particles entering into the sampler inlet relative to the number of particles present in the free stream, then the particle trajectory outside the sampler and into the inlet is the deterministic factor for the sampling efficiency. The particle trajectory inside the sampler is not important in this case."

Nov 1, 1995

By B. Kenney

For SOFCs, composite cathodes comprising an electronically conducting electro¬catalyst (e.g. LSM) and an conically conducting electrolyte material (e.g. YSZ) are considered to improve the electrochemical performance by extending the active reaction zone to regions beyond the electrolyte-electrode interface, as in the case of conventional cathodes. Interpretation of experimental data for composite cathodes, however, is complicated by the mixed conducting behaviour which results in local overpotential distributions throughout the composite cathode. These local overpotentials depend on many factors, such as the composition, particle size, porosity and thickness of the cathode. Reliable experimental data obtained from composite cathodes requires carefully crafted microstructural parameters in order to minimize the overpotential variations. A mathematical model of a composite cathode was developed using coupled differential equations describing transport and consumption of chemical species, oxygen ion and electrons. Simulations under various oxygen concentrations were used to obtain the reaction order of the oxygen reduction reaction. An apparent po2 dependency was then extracted from the predicted Rp vs P02 data. It was found that this p02 dependency can be significantly influenced by the micro-structural parameters of a composite cathode, primarily due to local overpotential distributions.

Jan 1, 2005

By Richard W. Hutchinson, Christopher Osterman

Abstract -The Selebi-Phikwe deposits are hosted by amphibolite to granulite facies gneisses of the Limpopo belt. The sulfide orebodies are generally stratiform and conformable to the foliation of the wallrock gneiss. Sulfide remobilization has occurred during metamorphism and has produced discordant sulfide veins, called piercement structures, which project into the hanging wall and foot­ wall gneisses. These piercement structures are compositionally similar to the stratiform sulfides, consisting mainly of pyrrhotite, pentlandite and chalcopyrite. However, texturally the piercement sulfides are coarse grained and inclusion-free, whereas the stratiform sulfides are fine grained and packed with tectonically produced wallrock inclusions. The piercement structure sulfides and adjacent stratabound sulfides were sampled and analyzed for major base metals and PGE's for comparative purposes. Most of the piercement structures were enriched in Cu, Ag and Au, whereas they were generally depleted in Ni, Co, Fe and PGE's. Changing elemental associations were observed from the stratabound sulfides and along the length of the piercement structures. This and the degree of depletion or enrichment of various major and minor elements in the sulfide piercement structures may reflect the relative mobilities of metals under metamorphic conditions. The similarities between sulfide piercement structures and the footwall Cu-POE veins in some Sudbury deposits are reviewed.

Jan 1, 1994

By J. B. W. Bailey

The Noranda Horne smelter in Quebec, Canada has change considerably during the last two decades to accommodate varying custom concentrate receipts, closure of the Horne mine, better working conditions, environmental programmes, new technology and increased energy and labour costs. This paper highlights the reasons for changing the smelter from two calcine charged and one wet charge reverberatory furnaces fired by coal to a smelter using. tonnage oxygen oil, natural gas and coal in a single wet charged reverberatory furnace and a Noranda Process continuous Reactor. The current operation 1 described, including three major topics; the use of oxygen/fuel burners on the charge banks of the reverberatory furnace which has increase the smelting rate from 680 to 1100 tonnes of concentrate per day; the oxygen enrichment of the Noranda Process converting air to achieve smelting rates of over 1800 tonnes of concentrate per day; the converting of the mixture of 73 percent copper matte produced from the Noranda Process and the 33 percent copper matte produced from the reverberatory furnace.

Jan 1, 1983

By B Abbasi

It is well known that most roof falls in coal mines typically occur at and around intersections. Room-and-pillar and longwall coal mining systems typically develop 3-way and 4-way intersections. This research develops an improved scientific understanding of stress distribution and associated instability behaviour around 3-way and 4-way coal mine intersections through 3-D numerical modelling and limited field observations. Numerical analyses were performed for an Illinois longwall coal mine to identify factors that influence intersection stability. The stability of immediate roof, floor strata, and coal ribs at and around intersections are considered with pre-mining regional horizontal stress. Non-linear failure analyses used the Hoek-Brown failure criterion for rock mass. Progressive failure zones in and around intersections were developed. For a typical 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of the immediate roof and floor layers. The mechanism of failure is similar for a 3-way intersection but the shape and extension of failed zones differ. For the 3-way intersection, the effect of off-set distance was analysed. It was found that minimum off-set distance of about 10 m (centre to centre distance between two 3-way intersections) was required to minimize interaction between two intersections. A simple instrumentation program monitor ground movements around intersections. These data were used to design the intersection geometry that is now being practiced by the mine. CITATION:Abbasi, B and Chugh, Y P, 2018. Instability analysis in three-way and four-way coal mine intersections, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 345–359 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By N. A. Warner

Virtually zero gas emission smelting is promoted as a means for securing environmental advantages and the general public’s acceptance. Concerns about climate change will increasingly make it more difficult for new primary metals projects to come to fruition unless greenhouse gas emissions are decreased. Assuming a sustainable market for sulphuric acid is not locally available, the next best option is high temperature reaction of strong SO2 with limestone or dolomite. This is followed by CO2 liquefaction and disposal either underground or in the deep ocean. The Voisey’s Bay nickel project is cited as an example where appropriate location of a new smelter close to large dolomite or limestone deposits would lead to a virtually zero gas emission operation. Most of the electrical energy required for producing technically pure oxygen and for liquefying CO2 and transporting it to disposal can be derived from smelting a bulk sulphide concentrate and then reacting SO2 at high temperature. Provided the smelter gases are properly cleaned before sulphur fixation, the sulphated stone should be uncontaminated and environmentally benign and possibly of use in the building and construction industry.

Jan 1, 1999

By M. Akser

Ilmenite, rutile, and zircon deposits of commercial importance have not been reported to-date from Turkey. However, information from recent reconnaissance activities indicates the possibility of an economically viable heavy-mineral deposit along the Black Sea coast of Turkey in the vicinity of Ormanli, northwest of Istanbul. Consequently beach and sand dune samples were collected from that area for additional analysis. Laboratory methodologies, designed to simulate standard industrial heavy-mineral plant practices, were used to analyze and evaluate the samples. Based on the analyses, and current market needs, none of the deposits in the Ormanli area qualify as a commercial heavy-mineral deposit.

Jan 1, 1995

By Q. Zhang, X. C. Wang, X. Q. Ao

The flotation separation of apatite and calcium-bearing gangue minerals (dolomite and calcite) has always been a problem in phosphate ore mineral processing research. The crystal structure and surface properties of minerals have an important influence on their floatability. In this paper, the theoretical and comparative analysis of the crystal structure and surface electronic properties of apatite, dolomite and calcite were carried out using the first principle calculation based on density functional theory. As a supplement and validation, the surface wettability of three minerals under different flotation conditions were compared and analysed by contact angle test. The results theoretically revealed that the three calcium-bearing mineral surfaces have similar surface electronic properties and thus exhibit similar floatability. In the flotation process, the anion difference between apatite and carbonate gangue should be fully utilised, and the minerals can be separated only after surface modification by flotation reagent. The contact angle test shows that phosphate and carbonate can be separated by using anion flotation collector after surface modification with acid. It is expected that this research is of interest for understanding the surface structure and electronic properties of apatite and carbonate gangue minerals and providing the theoretical basis for surface interaction. Keywords: Apatite, dolomite, calcite, surface structure, electronic property, density functional theory

Jan 1, 2020

By Otto E. Zwanzig

You may think long before this talk has been completed that the speaker is belaboring the obvious. Please let me put to rest here and now any doubt which you may have in this regard by assuring you that is precisely my intent, and for a very specific reason. We all profess to know and recognize the obvious, but I am impressed increasingly how often we forget or fail to act upon the obvious. Shortly after starting my first job upon graduation from college, I was asked by my boss to participate in a course on practical communications, particularly as applied to conveying proposals effectively to the client -- be he customer or company president. The concept or philosophy underlying this program was so simple and obvious that in my youthful brashness I saw only a gross waste by the company of e good, solid $1930 in compelling me to take the course. The sequel to this experience occurred about five yews ago when I was directing a 300-man marketing group. At that time I enrolled a dozen of my department heads, and subsequently about a hundred other personnel, in the contemporary version of that sane program. Why? -- because they all knew the obvious, but I could see how imperfectly they were implementing it. Truly, a wide chasm exists all too often in our beliefs on the one hand and our practices on the other.

Jan 1, 1962

By Renee Royer, Allan Punkkinen

As mines progress to ever increasing depth, new challenges are encountered with serious concerns for rock excavations in highly stressed conditions. New procedures have been undertaken or are under way to remove workers from the workface, mitigating risk and exposure to hazardous conditions. Rockbolting crews are at particular risk as they are the first line of defense in the installation of the ground support systems. One such initiative for removal of workers from danger has been with remote bolting. Equipment manufacturers have had the ability to remotely inject resin pneumatically into boreholes for several years, but it has not been recognized as a very effective method due to a variety of complications. This makes the installation of dynamic support system components such as the D-Bolt® increasingly difficult. More recently, hollow-core bolts have become popular providing far more effective installation when installed with pumpable, two component urea-silicate injection resins. Normet has developed high energy dissipation self-drilling dynamic bolts (SDDB®) to meet these challenges. Following several inquiries as to the effectiveness of pumpable resins for use with dynamic support components, Normet Canada performed comprehensive testing of the bolt and resin system at CanmetMINING in Ottawa to dispel or substantiate any preconceived beliefs. Several dynamic and static tests in direct and indirect loading were carried out. Results include tests in shear and early strength UCS of the resin to measure the performance of the SDDB compared with the established D Bolt as an effective dynamic ground support component. Underground field observations, installation methodology and in-situ testing are investigated.

Apr 26, 2022

By Christopher J. Bise

INTRODUCTION The principal means for transporting men, supplies, and mined material in an underground or surface mine are rail systems, conveyor belt systems, or a combination of the two. Typically, large underground mines use rail haulage from the mining sections to the hoist, with conveyor belts being used within the sections. Small mines use conveyor belts in the mains and sub- mains as well as in the panels. The size and layout of surface mines also contribute to variations in the way these haulage systems are applied. The following sections address the typical problems confronting mining engineers in designing these haul- age systems. For rail, these include rail selection and turnout design, locomotive tractive-effort calculation, and motor sizing. Belt haulage calculations include belt width and speed specifications, tension and take- up requirements, idler spacings, and motor sizing. TRACK LAYOUTS Introduction The adequacy of mine track layouts is dependent upon such factors as rail weight (Table l), suitable ties, a well-drained roadbed, and properly designed curves, grades, and track alignment. As long as the installation conforms to the manufacturer's recommendations, good service can be expected from the rail system. Typically, mining-engineering calculations for rack layouts have dealt almost exclusively with the design of turnouts. As such, the following section provides the necessary information for computing the theoretically correct dimensions of turnouts. Turnout Design Fig. 1 shows a typical turnout with an identification of the component parts. Fig. 2 identifies the variables that are used to determine the turnout dimensions. The formulas that concern the mining engineer are those listed: [ ]

Jan 1, 1986