Search Documents

By Esterhuizen S. Gabriel, Su W. H. Daniel, Tulu B. Ihsan, Klemetti M. Ted, Mohammed M. Khaled, Gearhart F. Dave

"A numerical-model-based approach was recently developed for estimating the changes in both the horizontal and vertical loading conditions induced by an approaching longwall face. In this approach, a systematic procedure is used to estimate the model inputs. Shearing along the bedding planes is modeled with ubiquitous joint elements and interface elements. Coal is modeled with a newly developed coal mass model. The response of the gob is calibrated with back analysis of subsidence data and the results of previously published laboratory tests on rock fragments. The model results have been verified with the subsidence and stress data recently collected from a longwall mine in the eastern United States. INTRODUCTION In 2015, there were 40 longwall mines operating in the United States, each producing an average of 4.5 million tons of coal per year, and they supplied 60% of the U.S. underground coal production. This represents a substantial increase from 50% three years earlier (Sears, Tulu, and Esterhuizen, 2017). During this period, reportable roof fall rates in U.S. longwall mines also increased. Large roof falls that can block the gateroads are not only a ground-fall hazard, they can disrupt the ventilation system, block the escapeways, and increase the potential for elevated methane levels in the gob. To address these hazards, the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) is conducting research to improve the design of ground control systems in longwall gateroads. Gateroad stability is primarily determined by the longwall pillar design. Generally, the required dimensions of the pillars around a longwall panel are determined first, which then dictates the location of the gate entries relative to the mined panel. The Analysis of Longwall Pillar Stability (ALPS) method is the most accepted gateroad pillar design procedure in the United States (Mark, 1992). The ALPS method accounts for local roof geology in the gateroad stability assessment by including the Coal Mine Roof Rating as an input parameter (Mark, 1992). The key assumption in the ALPS method is that unstable pillars result in unstable gate entries. However, experience provides examples of mines where pillar stability and gateroad stability are only loosely correlated (Su, Draskovich, and Thomas, 2003)."

Jan 1, 2017

By W. H. C. SIMMONDS

The mining, metallurgical, and petroleum industries can be viewed as financial or as social institutions or both. The differences between these two conceptions of their businesses will influence their environmental 'and social actions. During the next 10-20 years western industry will be subject to a drop in the growth of a more highly educated labour force and to the emergence of holistic economics, new national goals, and a new ecological perspective. The profitability of the mining industry may therefore be influenced by the human side of its business to a greater degree. The increasing human, social, and environmental responsibilities can be discharged by improving the miner's equipment; by learning to look at situations through the eyes of all those involved; by developing common 'languages' which governments and the public can understand; and by mediating where feasible on the international scene.

Jan 1, 1978

By P. James

Blue Planet Strategies (BPS) focuses on improved resource utilization and targets converting wastes into resources. New BPS capability (DEMET) wrings extra value from mining and processing wastes by enabling new production from waste and residual sources. This powerful platform technology provides considerable processing flexibility and enables various new economical treatment options to extract key metals from low level and process byproduct stream sources normally left as waste by traditional processing methods.[1]

Feb 23, 2014

This report discusses the nonfuel critical minerals position of the United States-both current and future (to the year 2000). We have assumed that there will be no major global disturbances-military, political, or economic-during the rest of this century. However, international relationships, strategies, and conditions that affect the supply of minerals are very tenuous, normal trading patterns can be easily upset, and national and ideological objectives can and do interfere with "normal" free market conditions. For example, the Department of Defense has reported that the Soviet Union is engaged in a strategy designed to reduce the availability of strategic minerals, through either physical disruption, market manipulation, or domination of producing or neighboring states. Although such a strategy poses serious concerns for the United States and the free world, the impacts of disruptions are not covered in this publication. Historical Perspective The modern industrial economy of the United States is founded on the production and use of minerals.* Two hundred years ago our forebears began taming a raw continent, developing a base for agriculture and a rudimentary minerals producing system. In the 19th century, with the aid of imported labor and capital, the development of America's vast natural resources was undertaken, and the transition from an agricultural to industrial society was underway. By the century's close, the United States had emerged as a great industrial power, partly through the development of such mineral resources as iron in Minnesota and coal in Pennsylvania.

Jan 1, 1983

By W. E. Stumpf

"SynopsisSouth Africa recently announced a resurgence in its commercial nuclear power programme. The implications for the development of the necessary high-level manpower within South Africa’s tertiary educational system and its national research and development (R&D) capacity in materials science and engineering, as well as in other engineering disciplines, are placed into perspective. An organized national process of developing this manpower by moving away from the previously high-risk and costly ’large programmes’ to rather a selection of ‘small and better’ research projects and a redefinition of what constitutes ‘nuclear materials’ are proposed as parts of this strategy.IntroductionSince 2008, and more particularly in 2014/2015, South Africa has woken up to the fact that significant steps need to be taken to ensure sufficient electricity generating capacity for the future, even beyond the coal-fired stations at Medupi and Kusile currently under construction. It is, therefore, encouraging to see some active large-scale wind farms in the Eastern Cape near Jeffrey’s Bay, in the Couga area, and others in the Western Cape already in operation. In addition, many solar energy projects are also progressing from the small localized scale to larger programmes in the Northern Cape, which may contribute some capacity on a national basis. South Africa needs to tap into its renewable resources of wind and solar much more, but will these projects solve the country’s long-term industrial needs? Unfortunately not. One cannot run mines and trains on solar cells. Industry needs reliable baseload capacity, and with very limited easily accessible hydrocapacity this leaves really only coal, possibly natural gas, and nuclear power as options. South Africa’s current over-reliance of about 90% on coal–fired power, however, places it in an internationally vulnerable position, and diversification into a more equitable energy mix should be a national priority for the medium to long term. South Africa cannot significant climate change confronting the human race, as the IPCC cautioned in 2013, and will have to adjust its future energy reliance to a more balanced combination of sources."

Jan 1, 2015

By A A. Puhalovich

The placement of chemically reactive mine wastes in mined out pits (æpit backfillingÆ) is increasingly seen by industry as best practice to manage long-term environmental risks. This is primarily because leaving wastes at the surface, or allowing pit lakes to develop, can result in unacceptable environmental risks. The costs and practicality of mitigation options such as installation of covers and community expectations of landform re-construction to achieve a post-mining, beneficial land use are also important drivers for pit backfilling.Pit backfilling can significantly reduce the post-closure risks to receiving environments, by minimising seepage due to tailings, acid/solute generating waste rock and/or salts derived from mine water treatment. Environmental risks are often highest where wastes are located close to the ground surface, due to relatively high rates of groundwater movement in near-surface aquifers and/or failure of engineered structures due to rainfall/erosion processes. Placement of these wastes at significant depth in pits, subject to mine planning and environmental assessment, can address these risks by increasing the path length and resistance from contaminant source to receptor, thus enhancing encapsulation of the wastes.Pit backfilling can also be cost-effective for mining companies. This is because existing pits are developed on the basis of an economic return and thus provide an opportunity to store tailings in an existing æengineered structureÆ at little or no incremental cost when compared with building and operating a new tailings or waste rock storage facility, often encompassing complex cover/drainage management systems. Key issues for consideration are mine planning, the long-term geotechnical behaviour of the wastes (eg consolidation of tailings which leads to release of acid/solutes in tailings porewaters), seepage rates to downstream receptors/agreed end point criteria and potential resource sterilisation. Internationally, mine closure guidelines are also showing a greater recognition of pit backfilling in the context of allowing mining companies to meet agreed post-closure land use objectives.In summary, pit backfilling can enhance the encapsulation of chemically reactive mine wastes and environment protection, and with agreement on post-closure beneficial land use, can also help to deliver post-closure benefits to communities.CITATION:Puhalovich, A A, 2012. Pit backfilling - Managing chemically reactive mine wastes and achieving rehabilitation objectives, in Proceedings Life-of-Mine 2012 , pp 279-286 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By J. Schmidl

In non-ferrous metallurgy the service life of refractory materials typically ranges from several weeks up to three years or more and is strongly dependent on operating conditions. To support our customers with the most viable refractory solution for their needs RHI Magnesita follows a structured approach of thermo-chemical calculations, experimental evaluation from lab scale up to industrial field tests and post-mortem analysis of used refractory materials. This paper will give an overview of the RHI Magnesita refractory selection process and the most recent developments of the experimental setup for the so called HF-IF test. This is a dynamic corrosion test that allows to determine fundamental properties of different refractory material types under process conditions subjected with respective customers process materials. The HF-IF experimental procedure is an excellent tool to simulate refractory wear in industrial processes, diminishing risks associated with plant trials and support decision making to choose the optimal refractory solution for the customer.

By S. Mao

Total station has been predominantly applied in stationary survey scenarios in construction. With the moving target tracking and point survey automation functions, a robotic total station (RTS) lends itself well to more dynamic applications. Nevertheless, a RTS unit is still unable to track multiple targets simultaneously or to survey a target point when the line-of-sight is temporarily unavailable. In this paper, we propose a methodology to synchronize and automate multiple RTS units intended to address dynamic tracking and surveying applications in the construction field. By using the application programming interface (API) from the manufacturer, we implement the proposed methodology and the prototype system integrates two RTS units in regard to space and time and communicates survey command instructions among RTS units through wireless networks. The two RTS units can be operated to survey the two ends of one swinging sling concurrently in order to retrieve the actual length of the sling within several millimeters accuracy. Besides, in applications where line-of-sight between a target object and one RTS unit cannot be guaranteed all the time, continuous surveying can be materialized by automatically delegating the task to another synchronized RTS unit with clear view of the target object. A field test was conducted to demonstrate the application of the proposed automation approach in which sling length was measured of a rigging framework used for lifting industrial modules. The testing results are presented and achievable accuracy and reliability are discussed. The proposed solution overcomes the limitations of global positioning system (GPS) and laser scanning and holds high potential to provide cost effective solutions to many dynamic field applications.

Aug 1, 2013

By Terrence J. Stobbe

On the job injuries to the musculoskeletal system are probably the oldest of the industrial safety problems. Long before we had pinchpoints to guard, chemical vapors to ventilate, and noise to enclose, people were getting strains, sprains, and sore backs from their work activities. In spite of the age of the problem, it remains a long way from being solved. The past ten years have seen a significant commitment by the sci¬entific community to understanding the problem. Engineers, scientists, doctors, and epidemi¬ologists have been involved, and as a result, today we have a much better understanding of the problem. The first step in understanding a problem such as this is to explore its history and epidemiology. The research done by Chaffin (1977), Snook (1970), Ayoub (1978), the ILO (1962), and others, led NIOSH to publish its Work Practices Guide for Manual Lifting in 1981. The guide was based on research carried out in general industry, but subsequent research by Stobbe (1983) and Peters (1983) has suggested that the nature of the problems producing injuries in underground mining is the same as in general industry. The problems are more intense in the mining environment.

Jan 1, 1984

By M. A. Cristovici

The possibility of using surfactants as wetting agents for the suppression of sulphide ore dust has been investigated. Numerous surfactants were examined to determine their characteristics and to investigate their ability to improve the wetting of the sulphide ore dust. However, the surfactants selected as suitable dust suppressors proved to have a negative effect on the flotation of the ore contaminated with such reagents. A method was developed to eliminate the detrimental influence of dust-suppressing surfactants. It consisted of surfactants adsorption on activated carbon and separation of loaded carbon prior to flotation. The technique is simple and requires minimal changes in the plant flowsheet.

Jan 1, 1990

By E. G. Davis, H. P. LeVan, L. S. Smith

Leaching of a Georgia umber ore when using both ferrous sulfate and pickle liquor was studied in the laboratory . The ferrous sulfate content of the leach solution was the major factor affecting the extraction of manganese from the ore . Time , temperature , and the sulfuric acid content of the leach solutions had relatively little effect on leaching of manganese from the ore ; however , these factors did affect the amount of iron extracted from the umber and/or precipitated from solution . Simulated countercurrent leaching of the ore with pickle liquor containing 130 gpl (grams per liter ) ferrous sulfate ( 48 gpl ferrous iron ) produced a pregnant solution having 16 gpl manganese and 41 gpl iron . Filtration tests of the leach slurries indicated that separating the leach solution and solids by vacuum filtration was impractical , whereas pressure filtration was feasible when the cake thickness was limited to about three- fourths of an inch . Fired pellets of the filter cake yielded a firm , hard product analyzing 56 percent iron and less than 0.1 percent sulfur .

Jan 1, 1964

By J. A. González-Anaya

This laboratory work presents a study of the effect of ultrafine grinding on the gold recovery of a highly refractory gold concentrate. The particle size of the concentrate was P80 = 46 µm and the main species present were quartz (28.58%), dolomite (25.63%), pyrite (20.93%), arsenopyrite (15.39%) and 112 g/t gold. After optimizing hydrated lime and lead nitrate additions, standard cyanidation with 1% NaCN, pH = 12.3, 25% S/L permits to recover only 9.4% of the gold. Different particle sizes were submitted to cyanidation. When the concentrate was ground to ultrafine sizes (P80= 4.6 µm), the gold recovery for the same cyanidation conditions increased to 67%, with cyanide consumption of 66.7 kg NaCN/t. Additional tests were performed in order to reduce the cyanide consumption. The reduction of the cyanide concentration in the leaching solution from 1 to 0.5% and the addition of 100 g Pb(NO3)2/t allowed the reduction of the cyanide consumption to 27.6 kg NaCN/t (58% reduction), while maintaining the same gold recovery of 67%. The remaining gold could be present as very fine inclusions or in solid solution in the matrix.

Jan 1, 2011

By Z Zhao

Coal dust is hazardous to underground coal workers and water spray is the most common and economic method for controlling coal dust. Previous studies proved that the addition of surfactants can improve the performance of water spray on coal dust suppression. The evaluation methods for surfactants vary from different studies. The zeta potential test is a common method for evaluating surfactants with ionicity. Generally, the suspension of coal dust with pure water usually showed a negative value of zeta potential. The addition of cationic surfactants can increase the zeta potential to a positive value with a small dosage, while the addition of anionic surfactants can only lower the zeta potential. However, there is a lack of comprehensive study to investigate the relationship between the zeta potential and the suppression performance for coal dust. The aim of this study is to reveal the consistency and discrepancy between the zeta potential and the suppression efficiency of a surfactant. Firstly, the mixture of cationic surfactant solutions and coal dust would be evaluated by the zeta potential test. The wind tunnel tests would then be conducted for the same surfactant solutions to measure and calculate the suppression efficiency. It was found that the addition of surfactant can increase the zeta potential and the suppression efficiency and it reached the greatest efficiency when the zeta potential approached to zero. The equilibrium of zeta potential can benefit the suppression performance of surfactants in the wind tunnel test. The result of this study can achieve a better understanding of the mechanism for coal dust suppression. The selection of surfactants will also be suggested for researchers or industries in terms of coal dust control. It would be more economic if a similar performance could be achieved by less consumption of surfactants.

Oct 12, 2022

By Y Li, S Ramazan, E Topal

A mine waste dump progression plan can provide a clear outlook of the mining operation. To produce such an output requires detailed placement schedule of the mined material, including the volume (or tonnage) and the allocated dumping location. However, current practise mainly focuses on the ore production, over-simplifying the waste material scheduling. As a result, a rock dump is often treated as a single point in long-term planning, making it difficult to predict the waste dump progression pattern over the life-of-mine. Without such a guidance, it is almost impossible to carry out progressive rehabilitation on the waste rock dumps. The lack of dumping schedule could cause delay in development construction, ie tailing storage facility and run-of-mine pad. Other downstream effect due to the over-simplification is inaccurate estimation of required truck hours, which could have huge financial impact on the operation.In this paper, mixed integer programming (MIP) models of different objective functions, ie maximise truck productivity by minimising the overall haulage distance, minimise required truck deviation between adjacent years, and a hybrid between the two objectives, are utilised to generate the long-term optimum rock placement schedules under the criteria of satisfying site specific conditions. All three MIP models are implemented in a large scale open pit mine. The numerical solutions from the models forms three different rock placement schedules, based on which, the yearly truck requirements are easily calculated and compared. The graphical results show the three corresponding waste dump progression patterns over the life-of-mine, providing the optimised long-term forecast of the operation.CITATION:Li, Y, Topal, E and Ramazan, S, 2014. Optimising the long-term mine waste dump progression and truck hour schedule in a large-scale open pit mine using mixed integer programming, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 335–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Dr. Jagdish C. Agarwal

Kennecott Copper Corporation has developed a new hydrometallurgical process for extracting nickel, copper, cobalt and molybdenum from maganese nodules. This process (KCC Cuprion Process) utilizes a reduction leach operating at atmospheric pressure in the temperature range of 45 C to 50 C and has been successfully demonstrated in a continuous pilot plant processing 800 lbs of nodule ore per day. The chemistry, basic flow sheet and operating characteristics are presented and discussed.

Jan 1, 1978

By Pengfu Tan

In order to understand and control the formation of dioxins and furans in iron ore sinter plants and to possibly avoid expensive end-of-pipe removal stages, thermodynamic calculations on the stability of PCDD/Fs have been combined with sinter process modeling by means of kinetic simulations and computational fluid dynamics. Three thermodynamic databases of PCDD/Fs, derived using the Group Additivity approach and two computational molecular modeling methods, MNDO and PM3, respectively, combined with the SGTE database have been used to model the PCDDIF formation and the PCDD/F isomer distributions in iron ore sintering. The results show very similar conditions for the PCDD/F formation using the different databases. Concerning the isomer distributions of toxic PCDD/Fs, the calculated data derived from the MNDO method showed optimum agreement with measured values from industrial furnaces. The thermodynamic calculations also proved that the isomer distributions found in combustion processes are equilibrium values, while the concentration ratio of PCDDs and PCDFs in the wind boxes does not represent an equilibrium state. A CFD model of iron ore sintering was developed including the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. On the basis of these information and experimental observations reported in the literature possible pathways for the PCDD/F formation in sinter plants have been identified: PCDD/Fs are formed in the critical temperature region of 250 to 450°C below the combustion zone, are then carried downwards with the gas and condensed close to the bottom of the sinter bed. Transported to the discharge end with the solid mixture, they are again released into the gas phase when the flame front approaches the bottom. PCDD/Fs are also formed in the last wind boxes when the hot off-gases cool down and reach the critical temperature range. Consequently, methods to reduce the dioxin formation reactions are proposed including inhibitor addition to the sinter feed and off-gas quenching.

Jan 1, 2003

By J. Boldy

This paper is an attempt to place Canadian Precambrian volcanogenic deposits in perspective, by examining and compiling data regarding certain neglected fundamentals of size, grade, value, frequency distribution and spatial density. The discovery roles played by various exploration methods are compared and contrasted, and. using empirical methods, the probabilities of discovery are discussed, combined with the use of an effective 'cost-per-target' program. From these basic observations, realistic exploration judgments may be made. Using similar methodology, this format may be applied to other types of deposits. Precambrian volcanogenic deposits occur in a natural geometric progression in size. They number 110, of which 70% are pre-producers, producers or past-producers. These deposits are bonanzas and generally have a 'net pre-smelter' value of between $43 and $62 per ton. The statistically typical deposit is that which occupies the modal position, has 400,000 tons of ore, a value of $20 million and occurs with a frequency of 40%. A median deposit has 1.4 million tons of ore, a value of $70 million and occurs with a frequency of 15%. An upper-decile deposit ha s 13.3 million tons of ore. a value of $750 million and occurs with a frequency of 6.5%. The major, mid-upper-decile deposits have a minimum of 50 million tons of ore, a value of $3 billion and occur with a frequency of 4%. Five major volcanogenic deposits occur in the Precambrian and account for 54% of production. This contrasts with 55 deposits (all below the median) which account for 3.9% of production.

Jan 1, 1977

By Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Despite numerous empirical, numerical, and hybrid studies conducted on the subject of coal rib failure, mine fatalities related to rib failures continue to occur. To date, a standard methodology for the design of coal rib supports which can accommodate the wide range of unique conditions found in coal mines in the United States has not been developed, forcing mine operators to rely on the trial-and-error process or industrial legacy practices for the design of coal rib support patterns. In this study, to better understand the support systems' effectiveness, various rib bolting scenarios were investigated. A coal mass constitutive model is implemented to a Distinct Element Method (DEM) code, and rib factor-of-safety (RibFOS) analyses were performed by applying strength-reduction for the coal matrix and explicitly modeled face cleats. Ribs with various overburden depths and mining heights composed of solid Banded-Bright coal (BBC) were considered in this study. Different scenarios such as rib bolt length and the number of bolts were studied to quantify the effect of primary rib support density on rib stability. As a result of the unsupported coal rib analyses, a decaying exponential relationship is proposed between the mining height-overburden depth and the RibFOS. The developed coal rib models clearly show the coal-rib bolt interaction and illustrate how the addition of rib bolts restricts the movement of the coal rib. The results reveal that the strength reduction method in DEM code with the coal-mass model can aid in the development of practical primary support charts, which can help in the rib support design process. In addition, an unsupported RibFOS cutoff

By AIME AIME

THE 130th Meeting of the Institute was held in Birmingham on Oct. 13 to 15, with visits to other mines and districts before and after. The last visit of the Institute to Birmingham was made in 1888, thirty-six years ago, and vast development has been made in' the district since then. With proverbial southern hospitality compounding over this period of years the welcome given to the Institute was such that .it is difficult to express properly the gratification and appreciation of the visiting members and the officers of the Institute. The Birmingham News in an editorial said: Birmingham is duly appreciative of the presence of these gentlemen, not because they are all distinguished in their great services in the mining and metallurgical world, but for the further reason that our interests are very largely wrapped up in their deliberations. Birmingham is one of the great industrial centers of America. Their discussions are of vital concern to all of us.

Jan 1, 1924

By D. M. Baird

"Enormous deposits of gypsum of exceptionally high grade are readily accessible in southwestern Newfoundland. Coming large-scale production from one of these is resulting in renewed interest in deposits which have been known for more than a hundred and twenty years. General stratigraphy and structure of the Carboniferous rocks in which the gypsum occurs are de-scribed. The stratigraphic position of the basal gypsum-anhydrite zone is described. This massive evaporite horizon, which reaches a thickness of about 1,0001 feet, appears at Fishels-Heatherton, where it is largely undeveloped, and again on the nose of an anticline east of Flat bay, where a present production of 20,000 to 40,000 tons per annum is soon to be expanded to make it one of Canada's major producers. Detailed descriptions are given of the several types of gypsum, the relation of the gypsum and anhydrite, and the distribution of sodium chloride in the evaporite beds, and the bearing of all these on the origin of the gypsum are discussed. Brief reference is made to relation to world markets, mining and transportation, grade, and reserves."

Jan 1, 1959