Search Documents

By Rex B. McLellan, M. L. Rudee, T. Ishibachi

A modelfor dilute quasi-regular interstitial solid solutions is proposed in which the solute atoms can occupy both the octahedral and tetrahedral interstices in the bee solvent lattice. The distribution function, according to which the solute atoms are apportioned between the two kinds of sites, is calculated. The partial thermodynamic functions of the solution are calculated from the distribution function. It is shown that such a solution model can explain the deviation from linearity of the Arrhenius plot of the temperature variation of the diffusivity of carbon through a iron. The published difiusivity data is analyzed to obtain numerical values for the distribution function. Finally it is shown from the numerical values of the distribution function that the possibility of dual-site occupancy will have a negligible effect on the solution thermodynamics for this system. DeSPITE the large amount of experimental data available on the thermodynamics and diffusion kinetics of dilute solid solutions of carbon in a iron, many of the elementary properties of these solutions are not understood due to real or apparent discrepancies in the experimental data. Basically there is a lack of agreement between the solubility and diffusion data obtained by anelastic damping techniques and by bulk chemical thermodynamic methods. SPecifically the heat of solution of cementite in ferrite estimated from thermodynamic measurement1, 2 is about twice as high as that determined from anelastic damping measurements.3 Furthermore the diffusion coefficient D of carbon in a iron in the range -40" to about 150°C (covering about ten orders of magnitude) determined from anelastic damping techniques is such that an Arrhenius plot of In D vs 1/T is linear. However in the range of about 300o to 850°C where mass flow measurements of D have been made (covering about four orders of magnitude), although the data merges with the low-temperature data, the Arrhenius plot departs from linearity. The object of this paper is to present a more refined model of dilute ferrite solutions in which the solute atoms can occupy two kinds of interstitial sites. The experimental data is analyzed in the light of this model and it is believed that thereby some of the anomalies can be resolved. snoek4 explained the room-temperature internal-friction peak (usually referred to as the Snoek peak) in iron as the stress-induced ordering of interstitial carbon and nitrogen atoms occupying the octahedral (0, 0, 1/2) interstices in the bee lattice. From the consideration of a hard-sphere lattice model the (0, 1/4, 1/4) tetrahedral interstices are larger than the octahedrons but their symmetry would not produce the strain dipole necessary to give rise to the Snoek peak. Thus the presence of the Snoek peak is direct evidence that the octahedrons are occupied. Since the publication of Snoek's explanation, most workers have assumed that all of the carbon and nitrogen in the a solid solution was located in the octahedral sites. This assumption of universal octahedral occupancy has been implicit in the theory of wert5 for interstitial

Jan 1, 1965

By Saskia Duyvesteyn

Small ion-exchange resin particles provide faster mass transport than conventional-sized beads. Unfortunately, high pressures are needed to pump solutions through columns containing small resin particles. It is preferable to disperse fine resins in the solution being treated. Screens have been used to separate the resin from the solution, but screens do not retain fines created by attrition of the resin particles. We have developed a separation process based on flotation, which relies on the surface characteristics of the resin, instead of size. The resin is conditioned with a surfactant before dispersing it in the solution to be treated; this increases the hydrophobicity of the resin sufficiently for froth flotation, without introducing surfactant directly into the solution. The surfactant adsorbed on the resin surface does not appear to impair the kinetics of metal ion removal. A flowsheet for an effluent treatment process is proposed; other applications are clearly possible.

Jan 1, 1998

By M. C. Williams

The dynamic behavior of batch mill, CSTR mill, and a closed grinding network consisting of a mill, sump, and cyclone was analyzed using the dynamic population balance model (PBM). The dynamic solution of the PBM of a batch, CSTR and a closed grinding network consisting of a mill, sump, and cyclone forms the basis of the dynamic analysis presented here. Two numerical dynamic solution approaches were used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data was used to obtain the functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Different dynamic solutions were obtained depending on the numerical approach used. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995

By Kailash Narayan

Atlantic Richfield Company began operating a commercial uranium solution mining project in April, 1975 in Live Oak County, 10 miles southwest of the town of George West (Figure 1). The operation is designed to produce 250,000 pounds of U303 per year and is jointly owned by Atlantic Richfield Company, Dalco and U. S. Steel. The proprietary process employed in this operation consists of injecting an alkaline leaching solution into the ore-bearing formation through a pattern of injection wells. The uranium-bearing solution is then removed through producing wells using submersible pumps in central production wells. The produced solution is pumped through a pipeline to the plant area where the uranium is extracted. The barren solution is refurbished and returned to the pattern area for reinjection. The injection field and plant site are located in the drainage of Spring Creek, a small intermittent stream tributary to the Nueces River. Land use in the area is primarily agricultural -- cattle ranching and farming -- but several producing gas fields are present in the areas as well.

Jan 1, 1976

By A. J. Jacobs, J. W. Spretnak, R. Speiser

The activities of nickel in liquid iron-nickel solutions containing from 10 to 90 at. pct Ni were measured over the temperature range .1510° to 1600°C. A special function was devised whereby activities can be computed by a graphical integration using the results of chemical analyses on the vapor phase alone. The liquid solutions studied exhibit negative deviation from Raoult's law, but they approach ideality as the temperature is raised from 1510° to 1600°C. The maximum heat of solution is less than -8.0 kcal per mole. The entropy of solution is less than —2.5 kcal per mole deg at 1510°C, and changes negligibly as the temperature is raised. The liquid iron-nickel solutions do not follow regular solution behavior. THE activities of the components of a liquid alloy system can be determined in favorable cases from the partial pressure of the vapor in equilibrium with the liquid alloy.' Assuming that the vapor over the alloy behaves as an ideal gas, the activity of component i is given by the expression, Where the superscripts 1, v, and o signify the liquid, the vapor, and the pure component, respectively; the f's are the fugacities, and the P's, the pressures. The quantities Pi and Pi can be determined by the

Jan 1, 1960

By M. J. Pool, C. E. Lundin

THE relative partial molar enthalpies of aluminum, gallium, and indium in liquid tin have been measured at 750°K by liquid-metal solution calorimetry. The measured heat effects and the calculated relative partial molar heats of solutions at infinite dilution are listed in Table I along with the relative heat contents of the solutes calculated from the data of Kelley. All of the values are referred to 750°K even though the calorimeter temperature fluctuated by +1°K during the entire series of experiments. The effect of this small temperature variation on the experimental values should be less than the experimental error. The limits of error given in Table I represent the standard deviations of all values from the mean. In no case was the experimental deviation greater than the listed error limits. The reported error estimates only apply to the estimated precision of experimental values and not to their accuracy. Systematic errors could be present in the calorimeter which would affect the absolute values given. Moreover the heat-content data used could also be in error and this would affect the end results. The relative enthalpies used were listed in Table I so that future corrections could be made if necessary. The relative partial molar heats of solutions of aluminum in liquid tin and dilute A1-Sn liquid solutions are large and positive. The value at infinite dilution is given in Table I. In the dilute-solution region investigated the relative partial molar heat of solution was a linear function of composition. A least-squares analysis of the data gave the following expression at 750°K: Atf^ = 6195 - 12,160 A:A1(cal/g-atom) where XA1 is the mole fraction of aluminum in the alloy. This can be compared with the data of Cohen, Howlett, and ever' who obtained the expression: 1SM = 6075 - 10,750 XM at 573°K Apparently both the partial molar heat of solution at infinite dilution and the concentration dependence increase with increasing temperature. This same

Jan 1, 1964

How the Australasian and Canadian Codes (VALMIN and CIMVal) approach mineral property valuation is described. Brief comment is also made on the International Valuation Standards CommitteeÆs interest in a global valuation standard for Mineral (Extractive) Industries and the South African SAMREC initiatives to adopt a VALMIN-like Code. The conventional tripartite classification of valuation approaches into those that are Market-based, Income-based and Cost-based is outlined. It is best practice to use as many of these approaches as possible (and as many methods as reasonable in the particular circumstances), given the quantity and quality of the data available on the Mineral Asset (which depends upon the state of development of the mineral property). The use of specific methods must satisfy the basic considerations of logic and reasonableness and the purpose of the valuation. The competence, judgement and repute of the valuer are critical factors, since all valuations are time and circumstance specific. What constitutes æMarket ValueÆ in the different jurisdictions is discussed and definitions are given. Challenges facing the globalisation of a VALMIN-type Code for the international Minerals Industry are the influence of real estate valuers and the US jurisdictional idiosyncrasies. This is mainly due to a fixation on real property rights with a preference for using real estate-like comparative sales techniques (Market Approach) to the exclusion of Income-based approaches; a regulatory reluctance in the US to accept that Resources have considerable value; and the International Accounting Standards BoardÆs preference for Historical, rather than Current Value, accounting.

Jan 1, 2002

By P. Rooney

In due course, new smelters will have to be installed in order to meet the increasing worldwide demand for copper. This paper presents the results of a study made for the purpose of identifying the most desirable countries in the world in which to locate a new smelter. Both sociopolitical and economic factors were taken into account. Criteria developed and methods used to assess each possible location are described. The study indicated that the most interesting potential locations are Canada, -Chile, Portugal and the USA for new copper smelting complexes.

Jan 1, 1983

By M. Doggett

All 231 Canadian primary gold mines that produced from 1946 to 2004 were analyzed with respect to their production and economic characteristics. Trend analysis revealed that the average annual capacity of Canadian gold mines, as measured by ore processed or gold produced, has increased over time. Conversely, the average grade of gold mines has decreased over time. The distribution of gold output is highly uneven: for example, the 22 giant mines producing more than 100 t (metric tonnes) of gold account for 62% of total output. Small mines producing less than 10 t Au account for 54% of total mines, but less than 4% of total gold. Each historical mine in the database was evaluated on the basis of a set of economic and technical assumptions to determine if it would be economic to develop today. Based on the net present value using an 8% discount rate, only 103 of the 231 mines were determined to be economic. About 80% of the uneconomic mines had less than 10 t of contained gold, and 63% had less than 5 t. It is concluded that these small mines would not be viable today due to a combination of real capital cost increases, and more stringent permitting and environmental regulations. The implication is that future gold supply in Canada will hinge on the discovery and development of a new generation of larger mines. Given that only one giant mine has been discovered in the past 20 years, it seems likely that gold output will decrease in the future.

Jan 1, 2007

By H. Majima, E. Peters

The oxidation rates of pyrite, pyrrhotite, chalcopy-rite, chalcocite, covellite, bortzite, galem, sphalerite, and stibnite have beet2 carefully compared at 120 oC, using aqueous phosphate solutions buffered at pH 2.7, 7.1, and 11.2 as zvell as in 1.0 M NaOH and in am~onia-containing solutions. Under conditions of these studies, variations in rates of more than a factor of two per unit of mineral surface area were not observed for different minerals in phosphate buffered solutions, except that pyrrhotite showed unusually rapid oxidation rates In acid solutions, and stibnite showed very rapid oxidation rates in basic solutions. In caustic solutions, oxidation vates varied considerably, the most rapid being for pyrite and the slowest for sphalerite. In the presence of ammonia, only copper minerals showed more vapid oxidation rates in neutral solutions. Oxidation rates were measured on the basis of oxygen-consunzption rates per unit surface area of exposed mineral, using equivalent surface areas, mineral mesh sizes, pulp densities, agitation, and oxygen pressure. OXIDIZING pressure leaching of sulfide minerals has been a commercial method of treating concentrates of nickel, cobalt, and copper for over a decade, and recently the treatment of lead and zinc concentrates,' and even the recovery of sulfur from pyrrhotite by such processes, have been shown to be technically feasible.' Furthermore, the leaching of uranium ores by solutions acidified through the oxidation of pyrite and other sulfides present in the ore is commercially practicable.3 5 The mechanisms by which sulfide minerals oxidize in aqueous environments are not yet understood. However, certain generalities can be made for systems containing no unusual reagents, in which oxygen is the oxidizing agent. In acid solutions the oxidation of many sulfide minerals leads to the formation of elemental sulfur.8'7 The attack of some sulfides, notably galena (PbS), sphalerite (ZnS), and pyrrhotite (FeS), at temperatures below about 110°C leads to an almost quantitative conversion of the sulfide mineral to elemental sulfur according to the equation: On the other hand pyrite (FeS2) and copper minerals do not yield elemental sulfur quantitatively. Not more than 50 pct of the sulfur in pyrite is converted to the elemental form in acid oxidation, and this percentage is lowered by higher temperatures and possibly higher oxygen pressures.8'9 Copper minerals sometimes yield elemental sulfurlo'" but, since sulfur can reduce cupric ions with the precipitation of CuS or Cu2S, it is not likely that elemental sulfur is obtained in good yield. In acid solutions sulfur that is not converted to the elemental form always appears as sulfate salts or sulfuric acid. Sulfide minerals that yield elemental sulfur nearly quantitatively on oxidation in acid solutions tend to generate H2S when the conditions are not oxidizing. However, although it has been suggested that H2S is an essential intermediate in the mechanism of oxidation," this is doubtful because it is oxidized very slowly by oxygen. In basic solutions elemental sulfur is never formed, as predicted by thermodynamical considerations, summarized in the form of a potential-pH diagram in Fig. 1. However in neutral and basic solutions, unstable forms of sulfur not shown in the diagram appear during oxidation, notably thiosulfate (SOT-) and polythi-onates (S,O;-, x = 2 to 6).l3,l4 On prolonged oxidation only hexavalent sulfur as sulfate (SOi-) or sulfamate (NHzSO;) is found to remain, the latter appearing only in the presence of ammonia. The oxidation kinetics for thiosulfate by oxygen are the subject of a separate paper,'5 and were studied on the presumption that thiosulfate may, in fact, be a primary oxidation product for sulfide minerals, at least in neutral and basic solutions. A survey of the literature indicated that comparative oxidation rates for different sulfide minerals were needed to establish the role of the mineral structure and its thermodynamic properties on the oxidation rates and mechanisms.

Jan 1, 1967

By Tsembel Darjaa, Toru H. Okabe, Yoshiaki Umetsu

"With the purpose of extracting molybdenum and rhenium from molybdenum sulfide concentrate; .electrolysis of slurry, solvent extraction and ·precipitation operations were carried out. The slurry of the concentrate in 10 mass% NaCl aqueous solution was continuously circulated into a vertical type 10 stack bipolar electrolytic cell consisted of carbon electrode disks, and, the concentrate was dissolved by electrochemically generated oxidizers at 313 K. The current efficiency for molybdenum dissolution was 73 % after 10 hours electrolysis, and the leach solution was found to contain 0.2 mol/l of molybdenum and 4x10-5 mol/l rhenium. This result shows the dissolution is more than 8 times faster than that obtained using a single cell. The leach solution from electro-oxidation was then subjected to a solvent extraction for rhenium which is then recovered as sulfides. After rhenium separation, molybdenum was precipitated by pH adjustment, and solid MoO3 (H2O)x crystals, free of sulfate, were obtained from the leach solution containing large amount of so42-.IntroductionIn the past, electro-oxidation using a bipolar cell was applied for leaching molybdenite concentrate and ores at U. S. Bureau of Mines [1-3] and also at Bhabha Atomic Research Center [4]. In· these previous studies, Moebious type bipolar cells, in which electrode plates were vertically inserted into the free surface of the electrolyte, were employed and its effectiveness was demonstrated.Recently, the present authors studied on leaching of Mongolian molybdenite concentrate, and the effectiveness of leaching of the concentrate by electro-oxidation in alkaline and acidic NaCl solutions was demonstrated [5]. The leaching reaction during the process can be explained by the 18 electron transfer reaction of molybdenite (MoS2) with the oxidizers produced in-situ by electrolysis of NaCl aqueous solution. Further investigation was made with respect to various process parameters for electrooxidation such as pH, pulp density and temperature of the slurry, and the dissolution behavior of minor elements such as iron, copper, and rhenium [6]. Solubilities of molybdenum in the leach solution at, various temperatures and pH .was · studied, and feasibility of molybdenum recovery by hydrolysis of molybdenum species was demonstrated. By adjusting the pH of the leach solution, molybdenum oxides or hydroxides free from sulfate were successfully obtained from the solution containing large amount of sulfate ion. Rhenium present in the concentrate at a level of several tens of mass ppm was found to dissolve into the leach solution, and co-precipitate with the molybdenum compounds. Rhenium in the leach solutions, therefore, has to be recovered before precipitation of molybdenum, otherwise it is lost in the precipitate."

Jan 1, 2000

By Taner Sumer, H Altay Guvenir

Fragmentation in rock quarries is tried to be achieved by changing the specific charge, drill pattern and bore hole diameters by different experts. This paper is a brief summary consisting of the utilization of practical experiences of the other group on cost optimization procedure that takes into account blasting, transportation and crushing as a whole process and optimize the cost by defining the optimum gelatin based explosives to be used as a main primer of anfo in three different limestone and granite quarries, with similar rock characteristics.

Jan 1, 1993

A full account of the wonderful Arizona meeting will be published in the December Bulletin. For the strenuous, interesting, and altogether happy week, we express our hearty thanks to those marvels of energy and thoughtfulness, the members of the local committees in Texas, New Mexico and Arizona. In this number we publish the discussion resulting from the technical session on "Flotation." Because of the timeliness of the subject, this session's discussion was transcribed first and sent to the contributors, and, thanks to their promptness in revising, we are able to print it in this issue.

Jan 10, 1916

By A. C. C. Pacheco, L. C. Bertolino, M. L. Torem

On account of geological characteristics, Brazil is a country of large deposits of high quality kaolin, with the larger ones being located in its northern region. In the last years, kaolin beneficiation and production area is receiving great investments, aiming at a high quality kaolin production to be used in the paper industry, mainly intended for the foreign market. After the conclusion of expan- sion programs and with the advent of new production areas, Brazil is very soon expected to come in second place in the kaolin world production ranking.

Jan 1, 1998

By Jiangtao Li, Zhongwei Zhao, Xingyu Chen, Xuheng Liu

In order to produce good quality ammonium paratungstate, Sn needs be removed efficiently from the tungstate processing solution. The nascent hydrous ferric oxide has excellent adsorption ability and is often used as an adsorbent to remove metal ions from aqueous solution. In this paper, nascent hydrous ferric oxide is used to remove Sn from tungstate solution. Through experimental, the effects of pH value, reagent amount of adsorbent, reaction temperature and reaction time on the Sn removal are investigated. The study shows that 98% of Sn can be removed effectively from sodium tungstate solution and only 2% of W is lost during process under the conditions of pH 9~12, reagent amount of Fe addition 40 times Sn amount, reaction time 30min and room temperature. As the Fe addition reaches 90 times of Sn concentration in the ammonium tungstate solution, 99% of Sn is removed and APT with zero level purity national standard is obtained.

Jan 1, 2014

By W. B. Gogarty, W. C. Tosch

A new recovery process for producing oil under both secondary and tertiary conditions utilizes the unique properties of micellar solutions (also known as microemulsions, swollen micelles, and soluble oils). These solutions, which displace 100 percent of the oil in the reservoir contacted, can be driven through the reservoir with water and are stable in the presence of reservoir water and rock. Basic components of micellar solutions are surfactant, hydrocarbon and water. They may also contain small amounts of electrolytes and co surfactants such as a1cohol.r. The specific reservoir application dictates the type and concentration of each component. A salient feature of [he process is the capability for mobility control. Micellar solution slug mobility, by way of viscosity control, is made equal to or less than the combined oil and water mobility. Mobility control continues with a mobility buffer that prevents drive water from contacting the micellar solution. Laboratory and field flooding have proven that the process is technically feasible and that surfactant losses by adsorption on porous media are small. Introduction projects are under way to recover the maximum amount of oil under the most favorable economic conditions.' : New techniques are being developed to increase oil recovery,3" Polymer solutions are becoming an important means of controlling mobility in a waterflood. Thermal methods such as in-situ combustion and steam injection are being used in reservoirs containing highly viscous crudes. Surfactant flooding is receiving attention as a method of reducing interfacial tension to increase recovery.*'" Exotic recovery processes have been considered primarily for ' perations. Economics are unfavorable in most cases for tertiary recovery. studies at the Denver Research Center of the Marathon oil CO. have led to a new oil recovery method.* Micellar solutions (sometimes called microemulsions, swollen micelles, and soluble oils) are used to recover oil by miscible-type waterflooding. Basically, these solutions contain surfactant, hydrocarbon, and water. The method can be used in either secondary or tertiary operations. First, thc concept of thc process is considered in terms of the requirements for an effective miscible waterflood ing operation. Next, micellar solution properties are described including structure, composition, and phase behavior with reservoir fluids. Fluid characteristics are then considered as related to mobility control, and, finally, laboratory and field results are presented to illustrate the efficiency of the process. Concept of the Process Unit displacement efficiency and conformance determine the effectiveness of any oil recovery mechanism. In theory, a miscible waterflood should be capable of a 100-percent unit displacement efficiency with a correspondingly high conformance. Requirements for the slug of a miscible waterflood include (1) 100-percent displacement of oil in the reservoir contacted, (2) controllable mobility, (3) the capability of being driven through the reservoir with water, (4) a low unit cost to enhance economics, and (5) the ability to remain stable in the presence of reservoir water and rock. Micellar solutions satisfy requirements for the slug of a miscible waterflood process. Our discovery that these solutions acted as though they were miscible by displacing all fluids in the reservoir and by being displaced by water solved the miscibility problem. Adequate mobility control is possible by variations in solution viscosity through compositional changes. Economic requirements are met since micellar solution costs below $6/bbl appear possible, Mi cellar solutions stabilize surfactant in the presence of reservoir rock and water, thus reducing the importance of the problem of surfactant loss by adsorption. Fig. 1 illustrates schematically how these solutions are used. Operations start with injection of a micellar solution slug that serves as the oil displacing agent. Next, a mobility buffer of either a water-external emulsion or water solution containing polymer (thickened water) is injected to protect the slug from water invasion. Finally, drive water (water used in a regular waterflood) is injected to propel the slug and mobility buffer through the reservoir. Reservoir oil and water are displaced ahead of the slug, and a stabilized oil and water bank develops as shown in Fig. 1. Stabilized bank saturations are independent of original oil and water saturations. This means that, for a particular type of reservoir, the displacement mechanism is the same under secondary and tertiary recovery conditions. Oil is produced first in a secondary operation. For tertiary conditions, water is produced first. Movement of the slug through the reservoir is stabilized by the mobility buffer. An unfavorable mobility ratio usually exists at the interface between the buffer and drive

Jan 1, 1969

By J. -S. Park, H. -S. Jeon

This study has been carried out to develop a relatively simple hydrometallurgical process for recovering nickel as nickel sulfate from the spent nickel-cadmium battery residue in which cadmium was removed by vacuum distillation. This residue is composed of 36 % nickel, 20 % iron, and other metals such as cobalt. First, crushing and selective classification were performed to separate iron to produce a nickel-rich product (over 40 % nickel). This product was dissolved in sulfuric acid to obtain a nickel sulfate solution. During the dissolution, nitric acid and air were added to the system to enhance the iron oxidation reaction rate. The free acid remaining in the dissolved solution was neutralized by adding nickel carbonate. Iron was precipitated as iron hydroxide and removed from the solution. The nickel sulfate solution was then fed to a vacuum evaporator to concentrate the solution by evaporation of water and crystallized at around 45°C to obtain nickel sulfate hexahydrate. A recrystallization process could remove other impurities such as zinc and manganese.

Jan 1, 2000

By Arun .. J. Basu

The paper introduces Intelligent Air Management (IAM) as the core activity of M&I Group of Companies (M&I) for providing a total solution to any air management problems for mining and mineral processing operations implementing a comprehensive systems approach through a world-wide network of strategic alliance partners and in-house engineering team and manufacturing facilities in Mississauga, Ontario, Canada. Recommendations for energy-efficient ventilation in a vibration and noise free environment are made with the patented and innovative solutions supported by extensive computational fluid dynamics (CFD) studies. The solution scope extends from an intelligent and integrated exhaust silencer to a complete ventilation sys-tem solution including inlet and outlet control design and ducting for diffusers and silencers.

Apr 1, 2005

By Tiago de Abreu Siqueira

CO2 geological storage is one of the current technologies developed worldwide to reduce industrial emissions of carbon dioxide to the atmosphere. Two main mineral types of deep geological reservoir could be contemplated for CO2 storage: sandstone reservoirs and carbonaceous reservoirs. Geochemical reactivity of a dolomite-calcite mineral compound and magnesite pure mineral was studied with a set of nine experiments per crushed mineral phase with two saline solution and with mQ water and three temperatures: 50°C, 90°C and 150°C. Experiments were performed in batch reactors with 250 bar of CO2 partial pressure during 24h to assess the effect of temperature and salinity in constant CO2 pressure. Solid characterization was performed by XRD and solution analysis by ICP-OES. Acidification of solutions due to CO2 dissolution in water is the main source of reactivity in the system. Proton concentration increases and causes partial dissolution of initial dolomite, calcite and magnesite and release of Ca2+ and Mg2+ cations in solution. Bicarbonate anion (HCO3) concentration also increases due to CO2 dissolution in water and carbonate minerals dissolution. Temperatures of 90°C and 150ºC increase the kinetic of reaction and the dissolution of minerals and cations release in solution. New carbonate crystalline phase precipitates as a Ca, Mg solid solution between dolomite and calcite pure poles.

Aug 8, 2018

By T. H. Jeffers

Significant amounts of cobalt are present in readily accessible spent copper leach solutions. The Bureau of Mines investigated the feasibility of extracting cobalt from these solutions in a multiple-compartment ion-exchange (MCIX) column. The effects of aqueous flow rate, resin flow rate, column height, and compartment height on cobalt extraction were determined. Cobalt extractions of 92 pct or higher were achieved at solution flow rates of up to 5.5 gpm/ft of column cross-sectional area and an aqueous-to-resin flow ratio of 40:1. Overall cobalt extraction increased as the column height increased, but cobalt extraction per unit of length was more efficient in 8-and 12-ftco1umns than in an 18-ft column. Solvent extraction procedures were utilized to purify and concentrate the MCIX column eluates and produce a cobalt sulfate solution containing 70 to 80 giL Co. Metallic cathodes containing over 99 pct Co were e1ectrowon from this solution. Zinc, nickel, and copper byproducts were also recovered during processing of the ion-exchange eluates. Estimated total capital cost for a commercial-scale 10,000 gpm of a spent leach solution containing 26 million. With credits for zinc, nickel, and copper estimated net operating cost was $9.36/lb Co.

Jan 1, 1987