Search Documents

By J. B. Gayle

Coke-pushing difficulties have been the subject of much controversy but relatively little scientific investigation. Nevertheless, continuing pushing difficulties can greatly decrease the life of a coke oven and should therefore be considered in the selection of the blend and operating conditions used for coke production. The present Federal Bureau of Mines investigation was undertaken to correlate results of previous investigators and to supplement these results to the limited extent practical by us of an experimental slot-type oven. To this end, pushing pressures have been determined routinely for Tuscaloosa oven tests conducted during the past 10 years. Nevertheless, the accumulated information remains incomplete in many respects, and in view of the recognized inadequacies of the data, publication is now undertaken only because of the scarcity of published information on this important problem and the discontinuation of carbonization studies with this oven.

Jan 1, 1961

By A. E. Kasten

The contract objective was to develop and test automatic fire control systems for large surface machinery in surface coal mines. The effort described by the report covers the period from 31 January 1977 to 11 November 1977 and accomplished the following tasks: ? Data accumulation, mainly from visits to the major manufacturers and mine sites. ? Hazard analysis of blast-hole drill, mining shovel, and dragline. ? Recommended design concepts for automatic fire control systems for each of these vehicles. ? Detail system designs for each of these vehicles. ? Procurement of prototype systems for the blast-hole drill and mining shovel. ? Installation of the prototype systems on machines at a surface mine and demonstra¬tion of performance by fire tests on the machines.

Jan 1, 1977

By Mariana Carla Mendes Rodrigues

The present study deals with the effects of strain rate on the functional behavior of NiTi thin wires. The samples, in the austenitic condition at room temperature, were mechanically cycled 20 times by loading up to 6% strain followed by complete unloading, at 25°C. Four different quasi-static strain rates were assessed: 1x10-4, 1x10-3, 1x10-2 and 5x10-2s-1. The functional properties are described by means of critical stress to induce martensite, stress at maximum strain, energy dissipated per cycle and residual strain. The sensitivity of repeated cyclic deformation to strain rate is also analyzed in terms of phase stability. The results show that the fluctuation in the loading plateau, due to non-homogeneous transformation, increases with increasing strain rate. During cycling, it is observed that higher strain rates result in lower critical stress to induce martensite after the 5th cycle. However, the stress at maximum strain is higher at high strain rates, regardless the number of cycles. The accumulation of residual strain also increases with the strain rate due to the higher applied stress. During unloading, both the elastic deformation of stress-induced martensite and the reverse transformation seem to overlap at high strain rates. The dissipated energy behavior changes between the 1st and 20th cycle. No martensite is stabilized after training, but the intensity of the X-ray diffraction peaks of austenite increases with strain rate, as a result of stress relaxation.

Aug 17, 2017

By L. Thomas, D. Muteba, L. I. Nsenga, B. Mbao, G. Longo Banza

Owing to the high ore grades in the African Copperbelt and variable acid consumption, agitated leaching is common practice and is used more widely in Africa than in other regions. Two common challenges for agitated leach–solvent extraction circuits are higher presence of colloidal silica in the pregnant leach solution and elevated levels of total suspended solids. Both can negatively affect the physical and metallurgical performance of the solvent-extraction circuit, and lead to higher processing costs or reduced copper production. Operating in organic continuity is preferred to address such challenges, but is not always possible: additional treatment options may be advantageous. For this reason, Solvay recently introduced ACORGA® CR60LT, a new chemical additive to address these concerns. Continuous addition to the pregnant leach solution improves physical performance without negatively affecting Cu transfer or cathode quality. Results and benefits from commercial utilization of ACORGA® CR60LT at different operations in the Copperbelt are reviewed

Jan 1, 2023

By Z. Halifa, P. G. Geyer

Tapping a blast furnace is necessary not only to deliver the product, but is also essential for the safety of the furnace and workers in the cast-house. This paper will highlight the practices at ArcelorMittal’s blast furnaces in the Vanderbijlpark Works, with specific focus on tap-hole design and monitoring as well as casting practice. Extension of the tap-hole life and hearth campaign will be illustrated with reference to the methods of maintenance of the tap-holes, troughs, runners, and cast-house equipment. The importance of proper cooling, good thermocouple installation, and temperature monitoring will be explained.

Jan 1, 2014

By Błażej Doroszuk, Robert Król

Mill drums are essential equipment in various industries for the comminution of materials. To optimize their design and operation for efficient and cost-effective processing, it is necessary to understand the behavior of the mill drum under various operating conditions. This study investigates the behavior of a mill drum using a combination of experimental and numerical methods. The factors that can influence the behavior of the mill drum, such as the size and shape of the mill, grinding media, rotational speed, filling level, and material properties, are discussed. Experimental methods can be limited in obtaining measurements of internal processes, so numerical methods such as the Discrete Element Method (DEM) are also used to simulate the behavior of the mill drum. In this study, the experimental measurements of the motion of the grinding media are obtained using computer vision methods, and the numerical simulations are calibrated using the experimental results. A designed experiment approach is used to evaluate the performance of the mill drum under various operating conditions. The results of this study can be useful for the design and optimization of mill drums to achieve better performance and energy efficiency.

Jun 25, 2023

By Rossen A. Halatchev

This study introduces a new probabilistic approach to seismic stability analysis of embankments and slopes. The approach is based on Sarma's solution, which is modified through presentation of the seismic force by its horizontal and vertical components; i.e. the force may have an arbitrary inclination. The probabilistic modelling includes Monte Carlo simulation of the shear strength parameters of the soil mass, which are assumed to have a normal distribution. The probability of failure is determined based on the seismic co-efficient, which is treated as a random quantity. The probabilistic approach is illustrated through a solution of a numerical example from an opencast coal mine.

Jan 1, 1992

By H. Jehn

Like some other Pt-group metals palladium shows a low but considerable solid solubility of oxygen, which was found already from oxidation studies. The oxygen solid solubility of palladium in equilibrium with gaseous oxygen has been investigated at 900 - 1300 °C in oxygen (665 mbar) and air by gassing and analyzing polycrystalline samples. The 0-concentrations range from 40 to 90 ppm and decrease with rising temperature. The isobaric solubility can be represented by the least-squares fit log c0 = 0.5 log p02- 0.32 + 920/T (c0 in wt. ppm, p02 in mbar, T in K). The thermodynamic data of the exothermic solution reaction are calculated to ?H°= -17.6 kJ?mol-1 and ?S° -76.5 J?mol ? K-1. The behaviour of palladium in an oxygen atmosphere is characterized by the simultaneous reactions of the solution of oxygen in the metal and the formation and evaporation of volatile oxides besides the pure metal evaporation.

Jan 1, 1984

This study introduces a new probabilistic approach to seismic stability analysis of embankments and slopes. The approach is based on Sarma's solution, which is modified through presentation of the seismic force by its horizontal and vertical components; i.e. the force may have an arbitrary inclination. The probabilistic modelling includes Monte Carlo simulation of the shear strength parameters of the soil mass, which are assumed to have a normal distribution. The probability of failure is determined based on the seismic co-efficient, which is treated as a random quantity. The probabilistic approach is illustrated through a solution of a numerical example from an opencast coal Mine.

Jan 1, 1992

By Hee Dong Jang

Crystalline metal oxide nanoparticles such as lithium cobalt oxide (LiCoO2) and indium tin oxide (ITO) were synthesized from sprayed droplets of aqueous precursor solution by flame spray pyrolysis. Complete thermal decomposition of the aerosol precursors was obtained at high flame temperature. Molar concentrations of the precursor solution, and the flow rate of combustion gas such as hydrogen, oxygen and air were varied to control particle size, size distribution and crystal structure. The crystalline nanoparticles synthesized were nearly spherical, and their average primary particle diameters ranged from 11 to 35 nm for LiCoO2 and from 8 to 15 nm for ITO.

Jan 1, 2006

By David E. Fogelson

The breakage of rock by explosives depends largely on the ability of an explosive to transfer its stored potential energy to the rock as strain energy. Therefore, the relative rock-breaking abilities of explosives can be determined indirectly by determining the relative amounts of strain energy transferred to the rock at the time of detonation. This report presents experimental data on the strain energy contained in explosion-generated strain pulses in a granite gneiss. Six explosives were tested. The scaled total radial strain energy Es/W flowing outward through a spherical shell of scaled radius R/W1/3 surrounding the point of detonation was found to follow an exponential decay propagation law of the form [ ]

Jan 1, 1959

By Tamara Nestorovic, Luan T. Nguyen

"With the aim to mitigate excavation risks and reduce the costs caused by tunnel boring machine (TBM) stoppage when tunneling under uncertain soil conditions, prediction ahead of the tunnel face has become an increasing interest in the tunneling community. Our research topic is concerned with developing effective concepts for nondestructive identification of geological anomalies ahead of the tunnel face by waveform inversion of reflected tunnel seismic waves. The authors demonstrate that this new technique is promising in providing tunnel engineers with an accurate image of the geological situation that the TBM is going to encounter thanks to the waveforms’ rich information about the geological structure that affects propagation, reflection/refraction and mode conversion behavior of the elastic waves. By setting up a 2-dimensional numerical model for simulation of tunnel seismic wave propagation influenced by a dip layer change ahead of the tunnel face, the authors show that the waveform misfit to be minimized by the inversion process is highly multimodal and therefore propose a hybrid stochastic optimization method that can quickly and robustly converge to the global minimum. DEVELOPMENTS IN TUNNEL ADVANCE EXPLORATION Conventional site investigation by drilling boreholes helps to draw a general image of geological structures along the borehole axes but that image is likely to misrepresent the detailed geological structure due to limited sampled locations. Due to high costs and restricted boring space which deep tunneling and tunneling under urban areas encounter, many industrial and academic research groups have had great interest in developing nondestructive ahead of the tunnel face prediction systems. That means only excitation sources and receiving sensors, which are usually placed on the ground surface or on the side walls or on the cutter head of the TBM, are used for acquisition of the measurement data. The recorded signals in the form of seismic or electromagnetic/ electrical waves, which travel through the geological structure or are reflected back from it, hold the signature of the geological structure of concern, such as geological layer changes, fault zones, erratic rocks, boulders, construction remnants, etc., and therefore can be used to reconstruct the spatial and material properties of those hidden geological structures. Most common nondestructive ahead-of-tunnel investigation systems to date are based on interpretation of reflected elastic/ acoustic waves (seismic waves) and analysis of electromagnetic/ electrical resistivity signals (Mooney et al. 2012). However, due to insufficient penetration depth and spread of signals generated by radar and geoelectric sources, the use of seismic waves for ahead of the tunnel face prediction (tunnel reconnaissance) is more preferable (Kneib et al. 2000; Bohlen et al. 2007)."

Jan 1, 2016

By John W. Taber

Discovery of these unusual fluorite deposits was brought to the attention of the Bureau of Mines late in 1951, shortly after the first locations were made. A brief investigation of the deposits by the Bureau revealed seven principal outcrops of fluorite in two areas. The smallest outcrop continuously exposes massive fluorite over an area 25 by 55 feet; the largest outcrop is a similar exposure 180 by 240 feet. The deposits appear to be sharp-walled, low-angle-, tabular ore bodies in granite and are at least 10 feet thick. The Bureau investigation of the deposits included bulldozer strip-trenching, drilling and blasting rock cuts, and channel sampling across three of the largest outcrops. This sampling indicated an average grade of 97.2 percent CaF2 and 1.44 percent SiO2. Preliminary metallurgical tests on the ore indicate that it can be concentrated to acid-grade specifications by simple gravity methods. One laboratory test recovered 78.4 percent of the fluorite in a product containing 98.7 percent CaF2, 0.25 percent SiO2, and 0.10 percent Fe2O3.

Jan 1, 1952

By Hideki Yamamoto, Norihiro Murayama, Junji Shibata

"Hydrothermal syntheses of zeolite from coal fly ash were carried out by using various alkali sources. NaOH, Na2CO3, KOH, K2CO3 and their mixture were applied for an alkali source of zeolite synthesis. The various physical properties of the reaction product, such as the kind of zeolite crystal, cation exchange property, surface texture and so on, was investigated through the zeolitization reaction from fly ash. The mechanism of zeolitization reaction was considered from these results.Zeolite P(NaP), hydroxysodalite(HS) and chabazite(K-CHA) are synthesized as zeolite species, when fly ash hydrothermally reacts in various alkali solutions at 393K. The crystal structure of the products obtained in NaOH solutions for 3h changes from NaP to HS with increasing NaOH concentration. K-CHA formation in KOH solutions needs 10h of reaction time, which is longer than that of NaP or HS.Dissolution, condensation and crystallization steps exist in the zeolitization reaction from fly ash, and the particle surface of products remarkably changes in each step. The fly ash is spherical particles and the surface is smooth(Fig.1(a)). The dissolution of fly ash occurs in the heating process until 393K, and the particle surface changes like unevenness(Fig.1(b)). In case of NaP, the condensation of aluminosilicate ions takes place at 373-393K, and the amorphous aluminosilicate is deposit on the unreacted fly ash(Fig.1(c)). The crystallization of NaP already begins to occur at 393K and the surface is covered with fine zeolite crystals for 24h(Fig.1(d))."

Jan 1, 2003

By Y. -H. Cho, J. -M. Lee, J. -G. Jung

The effects of copper on the microstructure and mechanical properties of ultrasonic melt treated Al-xCu (x=0, 4) alloys were investigated. The densities of alloys were increased and their grain sizes were decreased by UST. The hardness and electrical resistivity measurements revealed that the amount of solute Cu within Al matrix was increased by UST. Both the yield and tensile strengths of Al-4Cu alloy were increased by UST. The improved mechanical properties of Al-4Cu alloy by UST were probably due to the reduced amount of casting defects (e.g. pore), grain refinement, and enhanced solid-solution hardening of Cu.

Jan 1, 2014

By M. Pillay

INTRODUCTION Heat stress continues to be a safety concern in underground mining. This is due to a number of reasons including increasing depths of mining, increased levels of heat generated from machines, ventilation systems being constrained from providing suitable levels of airflow and others. In order to assess if a thermal environment is safe for miners under normal or modified work arrangements, or to specify stop work conditions a heat stress index is used to guide decisions. Historically, a number of heat stress indices have been developed and applied in underground mines. These can be classed under three broad headings; single measurement, empirically based and rational indices. Do any of these indices perform better than the others? Which one allows simple determinations and decisions to be made in the mine? This paper aims to provide answers to these questions by comparing and contrasting three indices; effective temperature (ET), simple air cooling power (ACP) and Thermal work limit (TWL) for a range of typical mining wet and dry bulb combinations? The paper concludes with the identification of areas for future research. BACKGROUND Heat stress causes discomfort, increases physiological strain, decreases productivity and performance, and contributes to increased incidents [1]. Effective management and control of heat stress is particularly important in mining where hot working conditions are very common [2]. Heat stress index is a common indicator that is used by mine safety advisors and managers to guide decisions about safe work practices in mining under normal or modified conditions. According to Howes and Nixon [3] A safe heat stress control strategy for an underground mine has three elements: • Application of an environmental measure which reflects physiological strain with sufficient accuracy for the range of conditions encountered underground. • Acceptance of a functional relationship between the environmental measure and human performance which is used to optimise the environmental conditions achievable with either ventilation or ventilation and refrigeration. • A management control strategy based on the environmental measure which is designed to ensure that work in environments where excessive physiological strain may occur is prevented and corrective action is initiated. The link between these elements is an environmental measure that reflects the physiological strain a worker is subjected to. Since the turn of the twentieth century various indices of thermal stress have been developed (McPherson [4], Howes and Nixon [3], Brake [5]). In selecting a suitable environmental measure or index one problem that must be addressed is the ease with which it can be physically obtained relative to it accurately reflecting the physiological strain. No index can be universally applied and there is no single correct measure or index. However if an index has provided adequate control in a particular circumstance, then it can be regarded as correct for that situation.

Jan 1, 2019

By I. Demers

The abandoned Manitou mine site covers an area of approximately 190 ha near Val d?Or, Quebec. This old site has been generating acid mine drainage for several decades. In 2006, a partnership was established between the Quebec Ministry of Ressources Naturelles (MRN) and Agnico-Eagle Mines to reclaim the Manitou site using tailings from the nearby Goldex mine. These neutral tailings were to be deposited on top of the Manitou site. An extensive study was performed to evaluate specific reclamation scenarios to control acid mine drainage using Goldex tailings as cover material. The article first describes the global approach used for this evaluation, which includes in-situ hydrogeological monitoring, tailings characterization, laboratory column tests, and numerical modelling. Of the thirteen column tests, three were conducted to evaluate the parameters affecting the performance of covers made of Goldex tailings placed over the spillage area of the Manitou site. Geochemical and hydrogeological parameters were assessed during the leaching column tests for almost two years. The tests aimed at evaluating the effect of water table level and monolayer cover thickness on the overall performance. The testing procedure involved monthly leaching and measurement of geochemical parameters. Results indicate that water table position is the most important factor affecting the monolayer cover performance to control AMD. Based on these results, it was established that the water table must be located near the interface between the Goldex and Manitou tailings to effectively reduce AMD generation. Cover thickness also has an impact on cover performance, which is however less significant than the water table position. The testing scenario with a water table located at the interface with a one-meter Goldex tailings cover showed progressive improvement in effluent quality.

Aug 1, 2013

By M. R. Khalesi, S. Bellec, C. Bazin, D. Hodouin

This paper proposes a classification model to predict the split coefficient of gold ore particles as a function of the particle size and gold content. The model is calibrated and validated using data obtained from the sampling of an industrial grinding circuit. Model calibration is based on a complete simulation of the circuit and involves parameters related to the gold grain distribution in the ore as well as a grinding and liberation model. Since cyanide is added into the studied grinding circuit, assumptions related to gold dissolution in the mills are made to allow simulation results which reflect industrial behaviour patterns.

Jan 1, 2011

By Wei Yin, Yu Wu, Xiexing Miao

"For engineering problems of “three under” coal (coal trapped under buildings, waters-bodies and railways) exploitation, environment protection and gangue separation from raw coal underground exist in Tangshan Coal Colliery. By analyzing concrete technical problems, a technical approach of closed cycle “coal mining-gangue washing-backfilling-coal mining”, i.e. integration of coal mining, gangue separation and solid backfilling, is put forward with key technologies including gangue transportation with great depth, gangue separation from raw coal underground and integration of coal mining and backfilling. Based on the specific geological conditions of Tangshan Coal Colliery, 591m vertical feeding transportation system with great depth is designed; meanwhile, for efficient gangue transportation, ancillary wear-resisting pipe size and buffer equipment are optimized. Underground gangue separation system is created to be joined with the existing production system and backfilling system; besides, as per separation characteristics of coal and gangue, buddle jig is adopted for gangue roughing of raw coal underground. By cooperation of backfilling hydraulic support and other key equipment, the designed stope backfilling system completely realizes integration of coal mining and backfilling. Engineering practice shows that, through the research and implementation of the above key technologies, integration of coal exploitation, gangue separation and solid backfilling is successfully implemented in Tangshan Coal Colliery; moreover, it completely solves the three major engineering problems and realizes waste disposal, underground washing and separation, and ground surface subsidence control.INTRODUCTIONSo far, “three under” coal (coal trapped under buildings, watersbodies and railways) and key state-owned coal resources trapped under villages in China have reached 13.7 billion t and 5.22 billion t, respectively. With the development of coal enterprises, China currently has more than 1,600 gangue dumps (Miao et al., 2010a) with accumulated stack amount of 4.5 billion t, occupying a land area of 150,000 km2; moreover, surface subsidence caused by mining activities has damaged the environments of industry, agriculture, transportation and living, while new environmental pollution sources formed by coal related industries also result in damage to ecological environment (Huang et al., 2011a). On the one hand, due to large scale coal mining, some coal collieries suffering from resource exhaustion are faced with survival problems; on the other hand, coal mining has caused and been faced with increasingly prominent environmental problems, such as “three under” coal exploitation, waste disposal and ground surface subsidence control (Miao et al., 2010b; Zhang et al., 2009)."

Jan 1, 2015

By R. Hurman Eric

The flow of molten slag and matte and the estimation of the mass of settled matte in electric furnaces is discussed and the action of the electric furnace as a settler is considered. Particle size of the concentrate and its grade are major contributors to settler dimensions. Discussion on the production capacity of the electric furnace with reference to operating current, power input, furnace dimensions such as width and length and electrode diameter are given. These discussions are based on considerations derived mainly from experimentally determined properties of the slag such as its resistivity, viscosity and liquidus temperature. Extension of the design and operating considerations to circular furnace symmetry is also discussed.

Jan 1, 1995