Search Documents

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. T HE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept Iles,

Jan 1, 1965

By D. T. Pritchard

"Introduction""No accounting system is very good, and all of them are infinitely variable*.”The purpose of this chapter is to discuss those facets of a typical accounting system which are most commonly encountered by operating managers in mineral processing plants. However, before concentrating in any detail on these it is important to understand the broad purposes and basic techniques of any accounting system in any major business.The three broad purposes of an Accounting System are:- Administering, controlling, and recording the flow of cash in and out of the business. Cash is, of course, converted into other assets (or stores of value) such as inventory, plant and equipment, etc. These assets also have to be administered, controlled and recorded.- Internal reporting to Management for information, for control, and for use in making business plans and decisions. - External reporting to stockholders, government, lenders and other outside parties.In this chapter we shall organize our discussion of accounting practice in mineral processing plants around these three purposes of accounting and focus in some detail on specific practices and techniques with which operating personnel will be routinely involved. This chapter is divided into the following: Accounting Basics; Administration, Control and Recording of Cash Flows; Internal Reporting; Planning and Budgeting; Cost Control; and External Reporting."

Jan 1, 1989

By A. B. Needham

This report describes the exploration work done in 1941 in connection with the search for strategic minerals as authorized by the Strategic Materials Act approved by the President on June 7, 1939. It deals with the various manganese deposits and showings in the Tombstone mining district of Cochise County, Ariz. The exploration project comprised a study of the geology, mapping of the areas, and exploration of various mines and deposits by sampling old drifts, crosscuts, and scopes, supplemented by diamond drilling from underground stations. The Federal Government's manganese-purchasing programs have revived interest in occurrences such as the scattered deposits near Tombstone. Because of this, the Bureau of Mines project report on the Tombstone district, prepared originally in 1941 but not published, has been revised and now is being made public.

Jan 1, 1956

By M S. Powell

In this paper it is argued that we are entering a new mining era, based on considerably more challenging orebodies as we rapidly expand minerals production by exploiting previously uneconomic deposits. Rapidly increasing production costs cannot be sustained by continually increasing commodity prices, as illustrated by the recent downturn in the industry.Driven by reduction in grade, requiring the processing of 50 to 100 per cent more ore to recover the same amount of metal, often accompanied by finer grain structure - necessitating a finer product size and more challenging recovery - the productivity of the mining industry is dropping in real terms. The author suggests that tweaking current technologies and relying on economies of scale will not turn the industry around, but rather a switch to considerably more efficient processing is required.It is imperative to utilise the properties of the orebody, especially in terms of variability, in revolutionising our processing techniques. Our new mantra may be æselective mass mining with flexible processingÆ. This paper explores how this may be implemented using current technology and equipment in order to change the cost profile of the new mining industry. Orebody knowledge, based on the underlying process drivers, rather than proxies, is required. These properties and their variability will need to be propagated into the orebody through utilising the geological data rather than smoothing block averages, which destroys information on variability.Novel flexible circuit designs are presented that can respond to a wide variability in ore properties and throughput requirements in order to slash processing costs and energy utilisation, while enhancing overall recovery. The success of these circuits will be based on an ability to predict at both design stage and in everyday processing the variable ore properties, which is dependent upon reliable orebody knowledge that caries variability and underlying processing properties.CITATION:Powell, M S, 2013. Utilising orebody knowledge to improve comminution circuit design and energy utilisation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 27-36 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By H Esterhuizen

The Ernest Henry Mine (EHM) in Queensland, Australia is a Sub-level Caving operation that started production below the previously mined open pit at a depth of 535m. Current Production mining has progressed to a depth of 730m, with planned production mining to extend down to at least 1000m below surface. The inclined nature and geometry of the orebody combined with geological structures provides for challenging mining conditions. Over several years, Ernest Henry Mine has introduced measures to improve outcomes based on observations, monitoring and data analysis. As mining progresses deeper, EHM will continue to proactively take steps to ensure future outcomes are anticipated and mining can continue safely and uninterrupted. The focus of this paper is on the changes in seismic- and stress-driven behaviour of the rockmass experienced at EHM, the ground control measures implemented, and the anticipated future conditions and controls required. CITATION:Esterhuizen, H, 2018. The evolution of seismicity and ground control measures at Ernest Henry Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 20–41 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Douglas R. Piteau

"Assessing the stability of a slope cut in rock is basically a problem of engineering geology - geology, because it involves a sound understanding of the important aspects of geology, such as geological structure, ground water, weathering and other natural phenomena, which all relate to or exist in a geological environment, and engineering, in that quantitative evaluations and calculations are necessary, these being based on mechanics and relating to the strength of the geological materials and the forces causing instability of the slopes. The engineering geologist must make every attempt to. provide, in a quantitative way, information on those geological factors which are necessary for making calculations of the probable stability of the slope. These include numerical assessments of quantities relating to the characteristics of structural discontinuities, rock types, topography, hydrogeology, tectonic history and other environmental factors. Based on the development and extension of these general principles, both preliminary and final slope stability studies of some open pits in South Africa, Swaziland and Zambia have been conducted. Some of the basic concepts and techniques developed to carry these studies out are described."

Jan 1, 1972

By S. F. Emmons

Jan 1, 1899

By Courtney E. Cleveland

THE gold deposits of the Pioneer and Bralorne mines, in the Bridge River district of British Columbia, are closely associated with a long, narrow intrusive body of extremely variable composition, outcropping on the northeast side of Cadwallader creek and lying almost entirely within the property boundaries of the two companies. Other masses of the same type of intrusive rock are found in the district, more or less along the line of the main axis of the Pioneer-Bralorne in trusive, and have associated with them variable amounts of gold-quartz mineralization (Figure 1). The ore deposits of the district have been the subject of investigation by officers of the Geological Survey of Canada at various times during the past 25 years, and articles on the geology and mines of the district have been published by various individuals in technical journals. A list of the more important re-ports follows: SELECTED BIBLIOGRAPHY

Jan 1, 1938

By K. B. Young

Possibly the most complex fatigue problem associated with the development of the axial-flow 'gas turbine is discussed in its broader aspects from the metallurgical viewpoint. Reference is made to nodal patterns, interference diagrams, etc. The use of such data in analysis of a turbine :blade failure is illustrated. Special attention is given to the influence of some metallurgical variables affecting fatigue strength and, in particular, heat treatment is shown to have a pronounced effect on .the relative fatigue and creep strength properties of a nickel-chromium-cobalt base alloy suitable for turbine blade applications.

Jan 1, 1958

In terms of throughput, product size and power draw, grindcurves provide a measure of the response of the mill performance to changes in mill operating parameters ? usually mill filling. Since presenting the principle in 2006, grindcurves have been applied to a wide variety of AG and SAG mills. Mill response has been carefully measured for variations in: mill fillings from 15% to 40%; throughput by a factor of two; power by 50%; feed blends; liner profile; and mill speed from 65% to 80%. The outcomes of this extensive program of work are presented as the measured grindcurves. How they have enhanced our understanding of mill operation and how they may be applied to practical daily mill control is discussed. It is proposed that this technique provides a viable and valuable mill control tool that may find extensive application in the industry.

Jan 1, 2012

By Robert J. Tuchman

This report presents the origins of the Bureau of Mines and the evolution of the Pittsburgh Research Center from its inception to its present form. Areas of major research emphasis over the years, as well as administrative reorganizations, are discussed.

Jan 1, 1998

By Brian Wilson, Franz-Werner Gerressen

"Cutter Soil Mixing, also known as CSM, was developed in Europe as an alternate method of Deep Mixing to the more traditional single and multiple auger techniques, and brought to market by Bauer Maschinen GmbH (Bauer), towards the end of 2003. Initial development of the technique had been completed in a joint venture between Bauer and Bachy Soletanche. In 2004 the concept was introduced to the North American market. Continued development of the method and demonstration of its versatility, both in terms of applications and applicable soil types has seen a steady growth in the number of designs incorporating the approach, and contractors offering the technique. This paper provides a brief overview of the variety and size of projects and applications where the method has been adopted, discusses some lessons learned with respect to equipment operation as well as the improvements that have been introduced to the equipment, and briefly reviews the current state of practice, as well as some of the associated on-going research and development.BACKGROUNDCutter Soil Mixing (CSM) is a technique for deep soil mixing that was initially developed as a collaborative effort between Bauer Maschinen (Bauer) and Bachy Soletanche, but which ultimately resulted in the separate development of two somewhat different brands of CSM tool. The Bauer brand of CSM entered the European market in 2004, and was first promoted in the North American market in late 2004, with the first project starting in 2005. The Bachy Soletanche brand, sometimes referred to as “Geomix” was first marketed in Europe in 2005 and the first model introduced in North America in 2007.The development of the Cutter Soil Mixing technique utilized the experiences gained from Trench Cutter/Hydrofraise equipment, developing a technique that incorporates two cutting wheels rotating about a horizontal axis as opposed to the more conventional deep soil mixing approach which utilizes augers and mixing paddles rotating about vertical axes. Whereas the Trench Cutter/Hydrofraise technique excavates the soil from within a panel, and supports the open hole using a bentonite slurry, the CSM technique cuts and displaces the soil whilst pumping a slurry/grout directly into the soil through a port located between the wheels. The combination of cutting the soil while introducing an appropriate volume of slurry effectively fluidizes the column of soil around and above the cutter head. While this process achieves a high degree of mixing, even on the downward cutting stroke, thorough in-situ mixing typically occurs on the withdrawal stroke, when most of the slurry is added."

Jan 1, 2015

The purpose of this paper is to present the methods used in ground water control and the considerations that affected the development of these techniques. Production at Knob Lake is currently proceeding at depths which may be as much as 200 feet below the original standing water table. In order to produce a more saleable product and to improve operating and maintenance conditions, it is necessary to depress the water table below the mining level. Considerable success has been achieved by drilling deep wells in strategic locations and installing vertical tur-bine pumps at depths of up to 400 feet. This method is especially suitable for operation under severe winter conditions and has reduced the detrimental effects by a far greater extent than other methods of water control, Spring runoff is handled in open sumps, but all other water from four mines, with flows exceeding 16,000 g.p.m., is pumped all year 'round from about thirty-five wells. THE Knob Lake operation of the. Iron Ore Company of Canada is located on the Quebec-Labrador border, 320 miles north of Sept-lies, a seaport

Jan 1, 1965

By M. J. Laurila

Simulation of coal preparation circuits is becoming a widely practiced technique used for the design of coal preparation plants. On a much more limited basis, simulators are finding application in off-line process control. A typical application in the latter category involves inputting projected coal washability data for a shift into the simulator and using the software to optimize product quality and recovery within a range of predefined specifications. The plant is then operated at SG?s of separation determined from the simulation exercise for the one shift time period. This procedure is useful in that it incorporates some form of advanced planning into preparation plant operations. There is an attempt made to reflect changes in feed coal quality on a shift by shift basis rather than continually running the plant near design specifications with changes in SG?s of separation being made in response to an inadequate sampling program which only provides a spot measurement of material that has already passed through the plant. Instead of instituting changes on a shift by shift basis, NHI has proposed a method whereby monitoring three major operating parameters, * Feedrate to jig * Flowrate from hydrocyclone overflow * Density from cyclone overflow the ongoing plant operating performance can be accurately predicted on a continual basis, i.e., updated hourly. Using a distribution curve to predict the split between the clean coal and refuse from a given separator does not account for variations in efficiency that occur as a result of variations in operating parameters. NHI and Arch have studied the effect of both jig loading and solids content in the recirculating load to the jig on product quality. As a result, relatively simple measurements can be made on-line in a preparation plant which will provide input data to the simulation program that enables the prediction of jig/hydrocyclone circuit performance on a real time basis.

Jan 1, 1985

By B L. Sainsbury, M F. Lee, A Penney

For most practical rock engineering purposes, stress versus strength conditions around underground openings for which rock masses fail and their various modes of failure, are reasonably well-understood and predictable. Some rock masses and particular rock types fail slowly and relatively quietly. However, others can fail rapidly, violently and maybe with the ejection of significant broken rock. In some countries and in some mines, the latter style of violent fracturing and failure of the rock mass is referred to as ‘strain bursting’. It can be alarming and extremely hazardous to nearby miners and machines. For such situations, the design and installation of appropriate ground support, to provide a safe work place, can be challenging. At any particular mine site, it’s often generally understood which local rock masses (rock types) are prone to strain bursting. Competent and strong siliceous rocks and some massive sulphides are often the main offenders. While some neighbouring, equally-competent and strong rocks might also fail, they do so more quietly and without ejection. To understand this contrast, a better understanding of the fracturing process is required other than simple and standard strength versus stress considerations. Suites of standard intact rock properties from numerous Australian mines have been used to define and help understand different high-stress failure styles for component intact rock; especially those prone to violent fracturing (strain bursting). Simple considerations of micro-fracturing (defects in the intact material), plus the available energy at failure versus the energy consumed during fracturing, distinguishes between over-stressed and competent rock types that fracture violently and those that don’t. CITATION:Lee, M F, Penney, A and Sainsbury, B L, 2018. Proneness of competent over-stressed intact rock to violent fracturing, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 170–184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By R. Wisniewski

Every underground coal mine in the United States must deploy and operate a wireless communication and tracking system. This paper addresses the reliability and availability of an installed tracking system and the communications infrastructure that supports it. A particular interest is the requirements for the systems to operate continuously without failure after a mine disaster for 96 hours, and the requirements in the MINER Act for the tracking systems to be ?calculated to be serviceable? and the communications systems ?redundancy?. These requirements imply a certain reliability and availability. This paper describes a quantitative way to assess these systems requirements, using the tools that are available and commonly used by the Reliability, Maintainability, & Availability community.

Feb 23, 2014

By P A. Grossman, J H. Rubinstein, M Brazil, D Whittle

Many ore reserves are harvested by a combination of open pit and underground mining methods. In these cases, there is often material that could be mined by either method, and a choice has to be made. The area containing this material is referred to as the transition zone. Deciding where to finish the open pit and start the underground mine is referred to as the transition problem and it has received some attention in the literature since the 1980s.In this paper, we provide a review of existing approaches to the transition problem encompassing: graph theory-based optimisation employing an opportunity cost approach, heuristics and integer programming. We also present a novel opportunity cost approach, that takes into account a crown pillar, and show how the new approach can be best applied through the unconventional application of an existing mine optimisation tool.CITATION:Whittle, D, Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2016. Determining the open pit to underground transition – a new method, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 731–742 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By H. R. Bullis

"A 2003 paper discussed the idea that as gold mining companies grow larger it becomes more difficult for them to discover or acquire new gold deposits large enough to replace extracted reserves on an annual basis. Deposits of the size required to replace annual production of very large gold producers (VLGPs) are statistically few. An update in 2005 reviewed VLGPs with respect to production, reserves, and reserve life and observed recent changes in the gold mining industry. Now, more than 12 years later, this paper explores how those VLGPs have fared and how the gold mining industry has changed. KEYWORDS Gold, Gold price, Production, Reserves, Very large gold producer (VLGP) RÉSUMÉ Un article de 2003 examinait le concept selon lequel, à mesure que les sociétés d’exploitation aurifère se développent, il leur devient de plus en plus difficile de découvrir ou d’acquérir de nouveaux gisements aurifères suffisamment grands pour remplacer les réserves qu’elles extraient annuellement. Statistiquement, il existe très peu de gisements de la taille requise pour remplacer la production annuelle des très gros producteurs d’or. Une mise à jour de l’article en 2005 se penchait sur la production, les réserves et la durée de vie des réserves des très gros producteurs d’or ; elle portait sur les récents chan¬gements au sein de l’industrie de l’exploitation aurifère. Aujourd’hui, plus de 12 années plus tard, cet article explore l’évolution et les résultats de ces très gros producteurs d’or, ainsi que les changements qu’a connu l’industrie de l’exploitation aurifère. MOTS CLÉS or, prix de l’or, production, réserves, très gros producteurs d’orINTRODUCTION In 2005, the world’s top five gold producing companies were Barrick (after purchasing Placer Dome; 9.1 million ounces; Barrick Gold Corporation, 2005; Placer Dome, 2005), Newmont (8.2 million ounces; Newmont Mining Corporation, 2005), AngloGold Ashanti (6.2 million ounces; AngloGold Ashanti Limited, 2005), Gold Fields (4.2 million ounces; Gold Fields Limited, 2005), and Harmony Gold (3.0 million ounces; Harmony Gold Mining Company Limited, 2005). During the years leading up to that point, there had been a flurry of activity in the gold sector directed at consolidating production and reserves to create very large gold producers (VLGPs). As defined in Bullis (2005), a VLGP is a mining company whose primary busi¬ness is gold production and that has annual gold production more than 5 million ounces. A stated corporate goal of several of the VLGPs at the time was to become the largest gold producing company in the world."

Jan 1, 2019

By A Vakili, F Harvey, H Greaves

Mine seismicity is one of the most difficult geotechnical risks to manage in seismically active mines. There are currently some established empirical and statistical methods that provide quantitative measures for seismic hazard assessment in operating mines. However, these methods are mostly suitable for quantifying the current or historical seismic hazard and often cannot be directly used to forecast the future hazards. Numerical modelling is the only analytical tool that can capture the level of complexities required for a meaningful analysis of mine seismicity and therefore to facilitate a reliable forecast of future hazards. However, there is currently no widely accepted and established guideline and methodology for analysing and forecasting mine seismicity using numerical modelling. This paper first provides a background on previous published studies on this subject and then outlines the key aspects that can affect the reliability of the forecasting for mine seismicity. These aspects include a) processing of historical seismic data, b) selection of suitable numerical modelling approach, c) Post-processing and interpretation of the model outputs. A case study is then presented for the Gwalia Deeps Mine where a new framework was developed to forecast future mine seismicity. High-quality seismic data for a period of five years was used for back-analysis and comparisons with the numerical modelling outputs. After development of the method, the future seismicity was forecast for the next 12 months and the actual seismicity was monitored against the forecast during this period. Results of this study shows promising potential for the proposed framework to be applied more routinely and at other mine sites. However, more validations are required at Gwalia Deeps mine as the mine proceeds to deeper levels. In addition, the method needs more improvements and should be tested and validated at other mining operations before it can be established as a proven method. CITATION:Vakili, A, Harvey, F and Greaves, H, 2018. Forecasting mine seismicity – towards a more established methodology, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 207–222 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By I. R. Jonasson, R. W. Boyle

"Current interest in the distribution of mercury in the natural environment comes from quite different, though not unrelated, sources. Mercury has long been an important metal in many industries and has, therefore, been much sought after by mining interests. The presence of mercury traces in the various media of the natural environment, namely soil, rock, air, water and vegetation, is exploited by geochemists not only to find mercury and polymetallic ore deposits, but also to find most other types of economic metal mineralization. More recently, however, mercury has caught the attention of health authorities and environmental scientists who are becoming increasingly concerned over the hazards of mercury wastes and the danger these present to the environment and to man. It is now apparent that the trace quantities of mercury, considered so important and helpful to exploration geologists, can be concentrated in the biosphere to such levels as to present considerable problems for ecologists. This article summarizes most of the available data on mercury contents in materials of geological interest and presents average normal values for rocks, ores, minerals, soils, sediments, waters and plants. The geoch.emical cycle for mercury in nature is presented and the mechanisms of mercury migration around the cycle are discussed."

Jan 1, 1972