Search Documents

By Donald T. Robertson, Kurt Hecht, Michael K. Muchard

"This paper presents case histories of driven concrete pile damage detected with dynamic testing methods utilizing strain gages and accelerometers embedded in the pile at the prestressing yard during pile construction. Data from the embedded instrumentation is compared with data taken with external bolt on instrumentation and other test methods such as low strain testing on the same pile. In the most severe cases, the piles were extracted revealing and corroborating the embedded data collector results.INTRODUCTIONDynamic testing of driven pile foundations was originally developed in the late 1960’s and commercialized in the early 1970’s. While the methods of analyzing dynamic test data have improved with the advancement of computer technology, the test method and the sensors used to acquire the data have changed little. In 1998, under a research grant provided by the Florida Department of Transportation, (McVay et al, 2002) an Embedded Data Collector system (EDC) was developed. The collector utilizes two sensor packs, each consisting of one strain gage and one accelerometer, embedded near the pile toe and pile top. Utilizing the toe sensor pack, the system provides reliable real time pile end bearing capacity measurements. This end bearing capacity is combined with a Case Method Solution augmented with an automatic damping calculation to provide the overall pile capacity, pile skin friction capacity and pile end bearing capacity. Also, since the gages are embedded, they have the ability to track all changes from the casting yard (i.e. prestress), driving, and subsequent setup (freeze, relaxation, etc) at both the top and bottom of the pile."

Jan 1, 2017

By P. Henry

A novel electrochemical cell has been developed for the recovery of MnO2 from residue of pyrolusite ore leading loaded with Fe, Al Ni, Co and Si impurities, This new process can be considered as an alternative to the traditional methods : S02, H2O2 or bioleaching. It has been observed to proceed fairly rapidly and could prove to be a more economically viable process, as well as being more environmentally acceptable. Electrochemical characterization and kinetic studies have shown that MnO2 is effectively leached by electrogenerated ferrous ions at high current density from a pulp containing less than 5 g8 Fe. The chemical reactions are : Cathode (inox) : 2F23+ + 2e ? 2 Fe2+ Bulk: MnO2 + 2 fe2+ 4H+ ? Mn2+ + 2 Fe3+ + 2 H2O Anode (Pb-Ag) : H2O ? ½ O2 + 2H+ + 2e Global: MnO2 +2H+ Fe2+ = Mn2+ + H2O + 1/2 O2 The catholyte (MnO2 pulp) circulates upward in the expanded mesh cathode separated from the sulfuric acid solution anolyte by a separator which shows high mechanical resistance, low porosity, low potential drop, and reasonable cost. Laboratory and mini-pilot tests have led to the construction of an OT crating pilot plant (100 kg/hr) able to leach more than 95% of Mn, Ni, Co at 1000-1200 A/m2, 50°C with high faradic yield (> 95 %) and low power consumption (3.2 kWh/kg kWh/kg &4D). New applications like the treatment of spent Zn-Mn batteries, polluted soils, spent catalysts and oxide ore (cobalt, nickel) with electrogenerated redox species are now investigated at a laboratory and mini-pilot scale.

Jan 1, 2000

By Ahmad Amini, Hadi Abdollahi, Pouya Karimi

Due to detrimental effects of cyanidation process on the environment in gold industry, application of cyanide alternatives such as thiourea are being highly considered in recent projects. In this study, the extraction of gold from poly metal ore, using thiourea was precisely investigated. The representative sample contained 2.5 ppm Au and 160 ppm Ag. The sample was categorized as oxide gold ore, because the main part of its pyrite was changed to iron oxide and hydroxide such as goethite and lepidocrosite. According to mineralogy, the main gangue mineral was quartz. It shows that gold grains are free and interlocked with quartz matrix. Also, the presence of a high amount of silver in free and sulfide forms and also the low content of other sulfide minerals such as base metal sulfides is a remarkable point of these studies. In the gold extraction process with thiourea, there are several parameters that affect the rate of gold dissolution such as concentrations of thiourea as a gold lixiviant and ferric sulfate as an oxidant, pH and size fraction of feed and leaching time. The influence of these parameters on the gold dissolution rate were investigated and optimized. The results showed that the concentration of thiourea is the most influential parameter which could increase the gold recovery to 71% (at 10 g/kg sample). The optimal amount of ferric sulfate was determined as 6 g/kg sample. Also, the optimal levels of size fraction of feed and pH of solution were 88% under 75 micron and 2 as acidity; respectively. Leaching time was 6 hrs. In addition, this sample was leached with cyanide and the optimized values of size fraction of d88=75 microns, pH=10.45, 2500 ppm of sodium cyanide with time leaching of 24 hours were concluded for maximum recovery of gold in solution. Finally, the results of cyanidation tests were compared to the thiourea dissolution after optimizing all affected parameters in cyanidation process.

Jan 1, 2018

By Richard L. Profio

A practical analysis of the three basic elements of a mining shovel's productive capacity. Payload Speed Reliability Improved dipper fill factor is explored referring to the latest generation of wide dippers combined with higher "bank horsepower" capabilities of modern drive systems. Cycle time improvement is reviewed including overall attachment geometry and coordination of motions. A specific case study is detailed. Basic reliability of welded structures, machinery components, and electrical systems are related to operating costs. Three basic elements determine a mining shovel's long term productive capacity: 1) Average payload per cycle. 2) Average cycle time; and 3) Reliability. This paper deals with productivity gains that are possible with existing shovels as well as new equipment.

Jan 1, 1984

By M. L. Smith

"In the Phosporia formation of SE Idaho, ore quality varies by depth, seam and distance along strike; phosphorus recovery is sensitive to these variations. Plant ore feed can be blended over time to minimize this fluctuation by using a combination of mine production and inventory stockpile scheduling. Mixed-integer and goal programming has been used to optimize short-term mine production, but the seasonal nature of mine haulage requires the use of stockpiles both at the mill and the mine. The contents of the stockpiles can also be optimized as part of the production scheduling problem, but introducing inventory control introduces a nonlinear term into the formulation. A solution using a piecewise linear formulation is modelled and solved using AMPL/Cplex, and solution strategies are discussed for similar large-scale problems. IntroductionIdaho’s minable deposits of phosphate rock are found in the Meade Peak member of the Phosphoria Formation; two separate zones of this formation are mined with a combined thickness of 30 ft to 60 ft. A generalized stratigraphic section of the Phosphoria section is shown in Figure 1, illustrating the degree of complexity encountered when scheduling mine production. Alteration of the formation results in higher grade ore zones near the surface and variable in P2O5 levels between seams and along strike. This variability is seen as well in other quality characteristics critical to the production of acid and elemental phosphorus. Further, plant recovery and nodule quality are sensitive to variations in ore feed; variability in SiO2, carbonates, moisture, organics (carbon), P2O5 and other constituents of the ore can strongly affect plant recovery. Because ore quality characteristics can vary as a function of the alteration zone (or seam) being mined as well as the depth and distance along the strike of the formation, scheduling of mine production can have a highly significant effect on recovery in the plant. As illustrated in Figure 1, there are nine seams containing 20% to 35% P2O5. Phosphoric acid and elemental phosphorus production requires an ore content of 30% and 25% P2O5, respectively. Variability between numerous beds that are mined and quality variation within a seam due to alteration greatly complicates production scheduling with the result that erratic mill feed characteristics greatly decrease recovery."

Jan 1, 1999

By Harry Jomini

Introduction The Wakefield plant of the Aluminum Company of Canada, Limited - a member of the Aluminum, Limited, group of companies - produces magnesia, magnesia fertilizer ingredient, and hydrated lime, from brucitic limestone. Wakefield is on the Gatineau river in Wakefield township, Quebec, some 22 miles north of Ottawa. The plant is near the western bank of the river adjacent to the Ottawa-Maniwaki highway and branch line of the Canadian Pacific railway. The plant is unique in the sense that it is the only place in Canada where brucite is processed. It is also distinguished for its outstanding safety record, as not a single lost-time accident occurred during either 1948 or 1949. The plant is amply provided with safety and comfort provisions in keeping with the standard practice in all of the twelve plants operated in Canada by Alcan and its associated companies. History Following the identification of brucite in the Rutherglen and Bryson districts in Ontario, occurrences of the mineral were discovered in the Wakefield area, Quebec, in 1939. After exploratory work on these deposits and investigation by the Bureau of Mines, Ottawa, on a method of extracting the brucite from the ore, a plant for treating the ore from the Maxwell property was built in 1941 by the Aluminum Company of Canada and commenced operations in early 1942. The process used is more or less in accordance with the method worked out by Mr. M. F. Goudge of the Bureau of Mines.

Jan 1, 1950

By Donald T. Mylar

It is axiomatic that in designing a bulk material handling system the primary consideration is the functioning of the machines. The structure is secondary -its reasons for being are to support, enclose and provide access to the machine, for servicing. This results in a wide variety of supporting structures. Other considerations are: plant layout, local soil conditions, climate, local laws and codes, and last, but by no means least, the Customer's wishes.

Jan 1, 1971

By Kain Petterson, P D. Katsabanis

Blast fragmentation, determined using image analysis was correlated to drill monitoring parameters in an open pit operation. Average fragment size and 80% passing size showed strong correlation with specific energy of drilling as well as with torque, while the same passing sizes did not correlate well with the rate of penetration. It was also determined that the uniformity of fragmentation decreases with the specific energy of drilling. Thus drilling monitoring parameters appear to be valuable in determining the blastability of the rock mass, enabling adjustment of blast loading to respond to changing conditions in the rock mass.

Jan 1, 2013

By Richard Brink, Eric M. Klein, Kenneth B. Andromalos

"A portion of the roof for a 129 x 144-inch, nearly 100-year-old sewer outfall in the City of Baltimore had deteriorated to the point that it resulted in the development of a large sinkhole in a residential neighborhood. A subsequent video inspection of the sewer outfall indicated that there was a hole in the sewer outfall, and it would need to be repaired . After initial backfilling of the sinkhole and repairs to the water service lines, a conventional wood shoring system was used to support the excavation and expose the Main Outfall Sewer to inspect and repair it. This excavation was unsuccessful because of loose sandy soils and high groundwater conditions. An innovative use of a steel reinforced jet grout excavation support system was ultimately used to underpin an adjacent 20-inch water main and other nearby utilities, and provide access to the top of the Main Outfall Sewer some 22 feet below the street surface to facilitate inspection and repair of the sewer. This excavation support system was also successfully utilized in the final repair of the sewer roof by serving as a buttress for the new roof system.1.0 IntroductionThe project site is located in a residential neighborhood with brick masonry row houses situated on the south side of Chase Street and a brick masonry church on the north side of the street. Figure 1 illustrates the location of the site. The City right of way is 65 feet wide, and the street is 40 feet curb to curb. The centerline of the Main Outfall Sewer runs parallel to and a few feet south from the centerline of the street. Other utilities running parallel to the street include a cast iron 20-inch water line built about 1910, a 24-inch terra cotta storm drain, a 6-inch terra cotta sanitary sewer, a 4-inch cast iron gas line and a 40-inch electrical duct. Cross utilities included a 4-inch gas line and several smaller water and gas service lines to the church and row houses. One gas line that was not shown in the City's GIS database was exposed during the excavation."

Jan 1, 2005

By A. W. Fletcher

Report of discussion at February, 1971, IMM general meeting (Chairman: M. J, Cahalan President) of a paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, December, 1970, pp. C247-52, and contributed remarks. Contributions are included from: Cahalan M.J., giving figures related to leaching Cu from pyrite at Rio Tinto 1880-1910; Noakes F.D.L.; Embling P.M.K.; Bradshaw A.V.; Le Roux N.W.; Kelly D.P.; and Tuovinen O.H. Questions were raised regarding impurity removal, effects of light and ultraviolet light on the bacteria, the economics of solvent extraction and the possibilities for other organisms or other metals

Dec 1, 1971

By T. G. Joseph, M. Welz

ABSTRACT: Joseph (2002) introduced passive seismic monitoring to measure mining equipment performance. This paper evaluates the potential of passive seismic monitoring to correlate mining equipment operation with oil sands surface response, with a mining hauler as the seismic source. When applied to moving haulers, this action–reaction approach is complex. Vibrations from on-board equipment, such as pumps and tires, dirty the signal with noise. To facilitate any correlation, the signal must be cleaned up. Existing geophysical analytical techniques were manipulated to evaluate the noise problem and to filter sufficiently to permit an evaluation of whether a mining equipment action–ground response relationshipis in fact discernable.

Jan 1, 2011

By Franc R. Joubin

"Gold has been found in many parts of the Bridge River district of British Columbia; but it is from a relatively small area in the valley of Cadwallader creek that most production has come. The ore-bearing area measures 1/2 mile in width by 3 miles in length; and for convenience it is called the Cadwallader gold belt in this paper. In this belt are found the Bralorne and Pioneer mines and in addition several prospects under development.The gold of the Cadwallader gold belt occurs in quartz veins averaging about 3 feet in width and containing about ½ oz. of gold a ton. Except for a relatively small amount of silver, no other metals are produced from these veins. The ore-bearing veins occur in a variety of rocks. They occupy reverse faults and tension fractures belonging to a distinctive fracture system. Some of these structures are ore-bearing over lengths exceeding 5,000 feet and depths exceeding 3,700 feet. The production of the Bralorne mine (1932-1945) is 996,383 oz. gold and 190,709 oz. silver; that of the Pioneer mine (1930-1945) is 777,588 oz. gold and 135,698 oz. silver. These two mines have together distributed about $25,000,000 in dividends.The Bridge River district first attracted attention in 1863* when prospectors were attracted by its small but rich placer gold deposits. Most of the important lode deposits of the Cadwallader gold belt were discovered in 1897 (11). Many years of desultory development followed and it was not until 1928 and 1932 that the Pioneer and Bralorne mines, respectivdy, entered into profitable production."

Jan 1, 1954

By M. J. Brnich

The purpose of this U.S. Bureau of Mines study was to assess the ability of trainees to don an unfamiliar self-contained self-rescuer (SCSR) after having become familiar with how to put on a different type of apparatus. Prepractice instruction was the same for all individuals learning to put on a device: a step-by-step, hands-on talk-through using the "3+3" method. Subjects were assigned to groups that had their initial donning instruction delivered on either the Draeger OXY-SR60B or the CSE SR-100. Trainees' performances were then evaluated using the other model. Donning trials were analyzed using a number of measures. It was found that SCSR design had a moderate influence upon how well the donning task transferred.

Jan 1, 2010

By A. A. Brant

"Improving geological and geophysical evaluation should serve to reduce the early-stage risk assessment and there-by contribute to exploration expenditure stimulation. The limitations of present-day methods are reviewed, particularly as to anomaly causes, depth penetration and quantitative physical interpretative abilities. Some of the problems now under study are discussed. Future developments expected include the treatment of quantitized geologic and geophysical data, as well as continuing attempts toward computerized interpretation."

Jan 1, 1967

By M Creech

During the 1990s, wider and more productive longwall panels were being introduced into the Newcastle Coalfield. The strata of the Newcastle Coalfield incorporate numerous massive sandstones and conglomerates, some of which formed the immediate roof of the coal seams being mined. The unexpected implications of introducing wider panels into this geological environment included more variable and increased subsidence, severe periodic weighting (with associated mid-face falls) as well as windblast.Subsidence prediction at the time was based on empirically derived data essentially relating subsidence to the width/depth ratio of the panel without accounting for actual widths, nor the impacts of variable geology. This approach required modification as locally derived data was gathered and reinterpreted.The interaction of massive strata located close to the roof of the mined seam resulted in dramatic implications for some of the operations. When associated with longwall goaf geomechanics severe periodic weighting events and crippling mid-face roof falls were the consequence. When associated with narrower panels and shortwall goaf geomechanics, mines in the region experienced aggressive windblast events. The relationships between the overlying massive strata, longwall panel geometry and the various risks encountered during this period is in the author’s opinion, the most concise still documented.As the extensive coalfields of Queensland turn to underground mining operations the relevance of these experiences cannot be underestimated. This paper will discuss recent developments as well as incorporating diverse subjects such as microseismic monitoring, low frequency radio emissions and ‘electrophonics’ as they relate also to the topic.Like Moriarty, massive strata can be disguised and can offend when you least expect. This paper documents a trail of crimes committed by conglomerate in the Newcastle Coalfield that were inflicted on the general public, miners and mining equipment. Although this paper concentrates on the criminal behaviour of conglomerate, this story is also relevant to other massive units such as coarse sandstones that may be more difficult to identify and apprehend. Currently Moriarty remains at large and able to reoffend at any time, once again taking advantage of the unwary.CITATION:Creech, M, 2014. Moriarty was a conglomerate – experiences and implications of coal mining under massive strata in the Newcastle Coalfield, in Proceedings Ninth International Mining Geology Conference 2014 , pp 47–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By D. J. Hallbom

The ?yield plastic? rheological model describes the flow behaviour of a variety of non-settling suspensions, including many types of mineral slurry. The current paper presents the laminar flow relationship (pressure gradient vs. flow rate) for a yield plastic fluid flowing through a pipe or cylinder. Simplified algebraic equations, suitable for engineering purposes, are presented for yield plastic fluids with values of the scaling factor in the range that includes most industrially important slurries. The laminar pipe flow relationship is one of the most important fluids engineering calculations. It may be used to determine the rheological parameters of a material in a capillary rheometer or flow loop. If the rheology is known, these relationships may be used to determine the laminar flow pressure gradient in pipelines of various sizes.

Jan 1, 2014

By J. M. Janssens, Van Quach Tinh, M. Ruel, R. Leblanc

"Microscopic studies of peat moss indicate a highly porous material. In view of using this natural product as an adsorbing agent for the treatment of polluted water, studies of its adsorbing power for beef extract and alkyl benzene sulphonate solution were determined. The effects of time of contact, particle size, concentration of adsorbent and concentration of pollutant were studied. In the case of beef extract, there is a COD reduction of around 27 per cent; in the case of the alkyl benzene sulphonate, the percentage reduction varied from 72 to 95 per cent. A water treatment plant based on the adsorbing power of peat moss with simultaneous recuperation of the pollutant is proposed."

Jan 1, 1971

By Ignacio Agramunt, Pamela Antonioli

¿Es la actividad minera positiva o negativa para un país? La respuesta la determinará el sector mismo, en la medida en que se decida a asumir el rol de motor del crecimiento sostenible, a través de su capacidad de añadir valor, es decir, de innovar. A partir de esta premisa, los autores analizan las brechas, dificultades y posibilidades que se plantean al tratar de modificar enfoques tradicionales, bien sea en competitividad, relaciones comunitarias, o procesos de mejora interna de las empresas. Al respecto, destacan la presencia de actores como el Hub de Innovación Minera del Perú, enfocado en facilitar, articular y acompañar la implementación de este tipo de procesos en las empresas.

Jul 30, 2020

By R. L. Nyirenda

An investigation of the reducibility of a cassiterite concentrate with charcoal was made in the temperature range of 1123-1373 K. The course of the reaction was monitored by a combination of sample weight loss measurements, product gas analysis, and chemical analysis of the reaction product. It was found that the cassiterite could be best reduced by a combination? of high temperature, reasonably high charcoal proportions, high charge poroslty, and the addition of a small percentage of lime. Analysis of kinetic data obtained from isothermal experiments using theory from the oxidation of carbon by carbon dioxide gave an activation energy value of 255 lci/mole for the consumption of carbon by reaction with cassiterite.

Jan 1, 1990

By Patzen Wu

Taiwan is located in the orogenic belt of island arcs on the western rim of the Pacific Ocean. The structure of the Taiwan coal fields is much complicated as a result of active Cenozoic orogenic disturbance in Plio-Pleistocene time. The abundant faults and folds have created poor structural conditions of the coal seams and some peculiar safety problems in mining however, the domestic coal still played an important role in the economic development of Taiwan for the years before 1968. Because of increasing mining depth and a decreasing number of miners, the coal production dropped from nearly 5.1 million metric tons in 1968 to 2.45 million metric tons in 1981. There were 173 small active coal mines and about 22 thousand miners in 1981. The coal mining in Taiwan has a history of more than one century. Specific efforts have been undertaken in solving major coal mine safety problems such as gas outbursts, bad roofs and weak floors, difficulty in ventilation due to deep underground mining, spontaneous combustion etc. We have thus acquired much helpful experience which, we deem, is worth reporting at this meaningful meeting.

Jan 1, 1982