Search Documents

By Dan Mahrt

"In June of 2009, a slope failure occurred along River Road in Bismarck, North Dakota. The slope failure affected approximately 300 feet of River Road with vertical displacements up to 3 feet, resulting in closure of the road. River Road travels along the Missouri River in Bismarck in a geologic area riddled with historic slope failures of varying sizes. River Road is a city roadway which travels along the Missouri River. The toe of the failure extended into the Missouri River, therefore methods to repair the slope needed to be constructed within United States Army Corps of Engineers (USACE) requirements, and be acceptable to the City of Bismarck. As this is a scenic area along the river, the stakeholders desired to maintain the scenic landscape along the roadway as a part of the slope stabilization.Due to the magnitude movement of the failure mass, the geometry of the failure was relatively easy to evaluate. In evaluating remediation options and collaborating with the USACE, the team determined that the scarp was situated primarily within the navigable portion of the Missouri River. This required USACE approval for any repair or remedial work downslope of the roadway. The City of Bismarck wished to reopen the roadway as soon as possible, therefore stabilization options were limited to working within the road right-of-way to avoid permitting for working within the navigable waterway.The remediation solution for this project involved a combination of driven H-pile and placement of lightweight fill to re-construct the roadway at the original grades, and avoid impacting the navigable portions of the Missouri River. This paper discusses the unique project constraints and the innovative solution using multiple technologies to successfully stabilize the slope.BackgroundIn June 2009, Bismarck, North Dakota experienced two consecutive days of significant rain resulting in over 5 inches of precipitation in a 36-hour period. Shortly after these rain events, a slope failure was noted on River Road, a city street along the Missouri River in Bismarck. Initial findings noted the slope failure affected about a 300-foot long portion of the roadway, with vertical displacements of about 2 feet. The city of Bismarck closed the roadway and began evaluating repair solutions for the road."

Jan 1, 2016

By H. Yoshida

Jet grouting was first introduced in Japan in the second half of the 1960s, approaching 50 years ago. By the end of the first 40 years, jet grouting from single to triple fluid systems had become a global technology. In the last ten years, progress in the jetting has been remarkable, and operational efficiency has improved. The quantity of carbon dioxide emitted in unit soil improvement has become one-third that of the initial technology. Meanwhile, technologies in waste recycling and horizontal jet grouting are also emerging. This paper discusses developments in the most recent ten years.

Jan 1, 2010

By Amanda R. Parry, Chris R. Pray

Predicting and modeling the soil structure interaction of laterally loaded piles with significant unbraced lengths is one of the challenges faced in designing many waterfront structures. Designers often rely on pile specific design software to calculate forces in an embedded pile and then couple that with either a structural design software to capture the behavior of the rest of the structure or use potentially overly conservative assumptions to omit modelling the piles entirely. Given that some projects have hundreds of piles coupled with hundreds of loading conditions, the shuttling of results from the structural analysis software into the pile analysis software can become cumbersome, difficult to track and manage, and prone to user input errors. An alternative approach recently used on two large marine infrastructure projects consisted of calibrating a structural analysis software to replicate the resultant outputs from a software developed specifically for pile analysis. This calibration was done using thoughtfully placed springs along a pile modeled in the structural analysis software to replicate the soil-structure interaction of the piles. The focus of this paper will be on the methodology used to calibrate the two software programs and an evaluation of the results which showed close agreement. Based on the two case studies, calibrating a generic finite element analysis software via this method should be considered as a reasonable and time saving design approach for pile-supported structures.

Sep 8, 2021

By Mario E. Rossi

Often geometallurgical models are prepared at various project stages from very few data and are assumed to be representative of very large tonnages. These may include recovery models; crushing and grinding parameters and models; models of concentrate grades; models of acid consumption; etc. These models commonly do not carry a measure of uncertainty or variability, and are taken at face value at the time of design and planning. This paper proposes a proactive approach to modelling variability, providing uncertainty estimates and thus allowing for risk analysis and mitigation of geometallurgical models. The variability model is built up by understanding the limitations of the pillars of a geometallurgical model: data uncertainty; geologic model uncertainty; domain definition uncertainty; and parameter estimation uncertainty. Of these factors, typically domain definition is the most significant contributor to geometallurgical model variability. First, the fundamental supports for these models are briefly discussed, with domain definition emphasized. Second, two methods for uncertainty modelling are proposed. The first, more applicable to conceptual or early-stage projects, is a simpler and more expedient alternative that provides initial assessments of variability. This is intended to aid management in decision-making related to budgeting, including further sampling and testing. The second, a block-by-block approach that allows a detailed assessment of risk for specific designs and mine plans, thus providing further opportunities for mitigation. In the example provided, emphasis is placed in communicating this variability to both management and technical personnel in the form of “measured-indicated-inferred” indicators and also block-by-block confidence intervals.

Jun 25, 2023

By L. E. Salinas-Farran, S. J. Neethling

Key variables in heap leaching include permeability, mechanical stability and mass transport. All of these properties can be manipulated by agglomerating and curing the ore before stacking it into heaps. The chemical and structural evolution of the agglomerates during curing is key to improving agglomerate properties and, ultimately, heap performance. It is possible to image the internal structure of agglomerates using SEM/EDX (e.g. QEMSCAN or MLA), although these methods are destructive and do not represent the 3D structure of the agglomerates. A non-destructive alternative is to image the agglomerates using X-ray Microtomography (XMT). Not only does this provide 3D information, it also allows the same samples to be repeatedly scanned, allowing the time evolution of the agglomerate structure and chemical composition to be tracked. In this paper we compared the behaviour of ores agglomerated using a combination of sulphuric acid and ferric sulphate with ones in which chloride ions are added to the recipe, since chloride leaching is gaining in popularity as a chemical alternative to bioleaching for sulphide ores. We tracked the curing process beyond the typical time scales to see the impact that this has on both the agglomerate structure and the subsequent leaching behaviour. Keywords: Heap leaching, curing extent impact, leaching kinetics, ferric-chloride leaching

Jan 1, 2020

By W. Guiye, L. Chongjun, L. Huinan, Z. Yangge, H. Long

The current application of copper-molybdenum (Cu-Mo) separation inhibitors is often associated with large dosage, high toxicity, environmental pollution problems. In order to solve these problems, a light sensitive Cu-Mo separation inhibitor LS（light sensitive inhibitor，abbreviated to LS） was developed. In this paper, inhibitory performance, photodegradation rule, and acting mechanism of LS were studied. The subsequent test results showed that, compared with traditional inhibitors, LS has shown comparative advantages, with lower dosage and good inhibiting effect. A series of flotation tests with LS as inhibitor were conducted on a Cu-Mo concentrate. A locked-cycle test showed that a molybdenum concentrate containing Mo 49.88% and Cu 0.6%, with 93.23% molybdenum recovery and a copper concentrate containing Cu 29.92%, with 99.99% copper recovery can be obtained. The photodegradation performance of the reagent was investigated under 365 nm, 254 nm and sunlight irradiation. The degradation of the reagents could be completely achieved by irradiation of three wavelengths of light. However, with the different wavelength of irradiation light, the degradation rate is different, the time required to reach 50% degradation rate being 3 h (254nm), 4 h (solar light) and 6 h (365nm) respectively. The inhibition mechanism on chalcopyrite was studied. FTIR study showed that LS could be adsorbed on the surface of chalcopyrite by chemical adsorption, which could enhance the hydrophilicity of chalcopyrite. Ultraviolet adsorption tests indicated that the adsorption capacity of LS on chalcopyrite surface was greatly affected by pulp pH value, and the proper pH value was 5-9. Keywords: Copper-molybdenum separation, Inhibitor, Light-sensitive, Photodegradation, Mechanism.

Jan 1, 2020

By L. Gutierrez, R. Yepsena

Enargite in porphyry copper deposits is an important mineral as it displays good floatability under the presence of the collectors usually used in the flotation of copper sulfides. As a result, copper concentrates grades are reduced. As scarcity of water resources is a problem relevant to Chilean mining, the use of seawater is a feasible solution. The behaviour of copper sulfides and molybdenite in the process of flotation in seawater was previously studied but not for enargite. The objective of this research is to study the behaviour of the enargite in different conditions of electrochemical potential during the process of flotation using seawater. The study was carried through micro-flotation tests using pure samples of enargite, at Eh values ranging from -300 to 500 mV(SHE), both in seawater and aqueous solutions containing calcium and magnesium. The results show that at pH 10.5 in seawater, the enargite and chalcopyrite recoveries are reduced throughout the whole range of Eh studied. At pH 9 in seawater, enargite and chalcopyrite are depressed under reducing and slightly oxidising conditions. The recovery of both minerals drastically decreases at Eh values lower than -100 mV and greater than 400 mV. The behaviour of enargite in seawater flotation differs from that observed in conventional water, since in the latter case the recovery of enargite decreases at higher potentials close to 500 mV. Keywords: Enargite, flotation, seawater, redox potential

Jan 1, 2020

By M. Rudolph, J. Sygusch

Froth flotation is well-established and efficient in the selective separation of valuable particles from unwanted material with sizes ranging from 10 μm to 200 μm. However, when it comes to the separation of ultrafine particles (< 10 μm) there are still some challenges, or rather opportunities. This research aims at developing a method for the separation of ultrafine particles based on multiple particle properties. Amongst such properties are wettability, morphology (shape or roughness) and size with applications not only in mineral processing but in general chemical engineering. In this study, three differently shaped fractions are used as valuables for testing: spherical particles, elongated particles and irregularly shaped particle fragments; together with ultrafine magnetite as the gangue material, in order to investigate the effect of particle morphology on ultrafine particle flotation, as well as wettability, which is varied by esterification using alcohols. Flotation tests are carried out using a novel flotation device that was designed especially for the flotation of ultrafine particles, combining advantages from machine-type froth flotation and column flotation. The results showed that, in contrast to previous studies, recoveries for ultrafine spheres were higher than for ultrafine fragments for all wettability conditions, and hydrophobisation generally increased particle recoveries for said morphologies. Tests using fibres showed different behaviour as hydrophobisation had negative effects on their recovery, despite increased selectivities and kinetics. These findings suggest that apart from influences of particle properties within the suspension zone, their effects on the froth characteristics should be studied in more depth. Keywords: Ultrafine particles, Flotation, Particle shape, Wettability, Esterification of glass, Hydrophobisation

Jan 1, 2020

By David N/A Doucet, Colter N/A Angell, William N/A Joa, Kyle N/A Wagner, Catherine N/A Johnson, Marty N/A Langenderfer

The Kingery-Bulmash (K-B) equations are a widely accepted means of predicting air-blast parameters from surface explosive detonations. The parameters predicted from these calculations include incident and reflected pressure, time of arrival, shock front velocity, incident impulse, reflected impulse, and positive phase duration. K-B calculations are based on curve fitting of experimental data and can be used to predict air-blast parameters for explosive weights from less than 1 kg (2.2 pounds) up to 400,000 kg (440.9 US Tons), and ranges of 0.05 to 40 meters (1.9 inches to 131.2 feet). The K-B equations can also determine the parameters for multiple explosive types using scaled distances and relative equivalency to TNT. An experiment was designed to demonstrate if the measured results for incident pressure, time of arrival, shock front velocity, incident impulse, and positive phase duration equal the expected results reported for the detonation of a small quantity of explosive determined by the K-B Calculator. Three surface-detonated 300-gram (0.66 pound) hemispherical charges of Composition C-4 were observed via high-speed imaging and hydrostatic pressure monitoring. The hydrostatic pressure generated from each charge was measured via piezoelectric pressure transducers at a scaled distance of 10 from the charge epicenter, and at elevations of 0.30, 0.61, and 1.22 meters (1, 2, and 4 feet) above ground level. Variances in experimental values from the K-B predicted values were recorded for each measured blast parameter. Time of arrival, which was redundantly confirmed through high-speed imaging analysis and hydrostatic pressure monitoring, showed the highest deviation from the predicted values at more than double the K-B predicted value. This report compares the observed blast parameters from the test series with the expected blast parameters from the Kingery-Bulmash Blast Parameter Calculator. Differences between the experimental and predicted values are reconciled through analysis and discussion of testing conditions, instrumentation setup, and scaling methods.

Jan 1, 2019

By S. Partney

Waste clay ponds are a necessary part of the phosphate rock beneficiation process. They are large, averaging a square mile in size; unsightly, in that they protrude 20 to 50 feet (6 -15 meters) above natural grade; stabilization and reclamation is slow; and they have had a history of catastrophic failure. The State of Florida has never published a specific rule regarding the configuration or height of these ponds, but has enforced numerous policies along these lines. The current rules are given and interpreted, along with the reasoning for current policy. In addition, an overview of the history of the policies, and an attempt at explaining the reasons for the changes that have occurred is given. The industry has been forced to make major monetary decisions, having effect for decades on mine economics, in a constantly changing regulatory environment. The Bureau of Mine Reclamation is confident that a direction of regulation has been solidified, but changes are still to be anticipated.

Jan 1, 1998

By T. Marin, J. E. Seccatore, M. Cardu

The most energy-intensive process in the mining industry is particle size reduction – comminution. The first phase of this process is blasting to fragment the rock from the initial Boussinesq’s halfspace size. Scientific literature demonstrates that the output of a blast in terms of fragment size distribution can be manipulated by varying the specific charge (powder factor) and charge distribution. This study focuses on the influence of blasting on the internal resistance of the blasted fragments; in particular the influence of the spatial distribution of charges. Small-scale blasts were performed on 14 marble blocks using different powder factors and charge distributions. Three control blocks were fragmented by mechanical means for comparison. The results show the correlations between charge distributions and the specific energy of mechanical comminution. Opportunities for adjusting charge diameter and distribution in opencast blasts to improve the performancet of comminution circuits are discussed.

Aug 8, 2024

By Roland Alford

The ballistic pendulum is a well-established piece of test equipment originally developed for estimating the velocity of bullets and projectiles. When trying to understand the effects of different tamping methods on explosive performance, the ballistic pendulum is an excellent tool allowing calculation of explosive charge impulse. Most ballistic pendula for this application are limited to narrow impulse ranges as the pendulum mass determines the angle of swing; and a mass capable of being moved by a small charge would be far too small for a larger charge. This paper describes a modular design (the Alford Modular Ballistic Pendulum) which overcomes this problem.

Feb 6, 2023

By Victor Freire de Oliveira

Em 24 de julho de 2014 entrou em operação o alto-forno 2 da VSB, projeto de fornecimento Paul Wurth cuja conclusão de montagem foi em 2011. O alto-forno, primeiro montado de um total de dois fornecidos, foi desenvolvido para conferir à VSB a maior flexibilidade operacional possível sendo capaz, inclusive, de operar com coque ou carvão vegetal, alternadamente. A instrumentação e automação são modernas e avançadas, oferecendo à VSB amplo controle sobre o processo. A presente contribuição técnica visa apresentar as características que tornam o altoforno 2 da VSB um reator especial e o mais moderno em sua categoria.

Aug 16, 2017

By José Aparecido Pereira

The innovative methodology developed by the author allows the elaboration of an Angle Roll Pass Design based on the practical observations of the rolling process and applies mathematical criteria, using the Ekelund´s formula supported by Advanced Excel tools (Reach Goal, PROCV-PROCH, Macros) and AutoCad. The first step is the definition of the number of stands, roll dimensions, gear boxes reduction, initial stock, average reductions, spread factors, finishing speed and type of grooves. For each pass are calculated: bite angle, spread, section reduction, lost and gain of temperature, separating force, speed, torque and motor power. After these calculations and checking of the parameters, the program calculates the dimensions of the passes transforming the flat passes into shaped ones. With these dimensions it is possible to draw the grooves using AutoCad and check section reductions. This methodology was already used for the development of a new project and also to check the parameters of existing ones, with comparison of the results and has shown to be reliable in real and tested projects. It is an innovative process that is not available in known literature.

Oct 1, 2019

By Alessandra Regina Machado Schifino

Neste trabalho foi realizado um estudo comparativo entre as normas utilizadas para validação da solda aluminotérmica em trilhos do tipo Premium – Vignole dos modelos TR, utilizada em reparos de trilhos ferroviários. As normas a serem comparadas são: ABNT (Associação Brasileira de Normas Técnicas), AREMA (American Rail Way Engineering and Maintenance of Way Association) e a Norma Europeia (British Standard – Railway Aplication Track – Auminothermic Welding of Rails). Esta comparação será realizada para avaliar a relevância da variação dos parâmetros utilizados em cada uma das normas e quais fatores devem ser analisados em mais de uma norma para que não haja dúvidas se os trilhos estão aptos para serem colocados em operação. Através da realização dos ensaios mecânicos e metalúrgicos, sugeridos pelas normas, encontra-se defeitos causados por diversos fatores, tais como: processo de fabricação, mau uso dos trilhos, falhas operacionais na soldagem, de preenchimento, de solidificação entre outros. Utilizando-se deste conjunto de informações será possível validar as soldas aluminotérmicas testadas.

Oct 30, 2017

By Caio Fernando Dias Guillen

Ao longo dos anos os aços para moldes plásticos tornam-se cada vez mais importantes no campo de aços ferramenta. A aplicação destes materiais estende-se pela indústria de processamento de diversos polímeros. Assim são esperadas propriedades específicas dos aços utilizados em cada condição: resistência mecânica, polibilidade, usinabilidade, resistência à corrosão e resposta à texturização são fatores determinantes na escolha do aço. O presente trabalho objetivou caracterizar, com relação às propriedades mais importantes para os moldes plásticos, uma gama selecionada de aços. Através de ensaios foi possível elaborar um quadro comparativo que define os aços que melhor respondem à determinada solicitação. A caracterização dos aços ocorreu através de ensaios de tenacidade, impacto, tração, dureza, características micorstruturais.

Jul 30, 2018

By Sebastien Flament

More and more Hot Strip Mills are facing defects on their products that lead to a rejection of complete product batches by their customers. Several of those defects are induced by excessive work roll degradation. This paper is focussed on the understanding of work roll corrosion and oxidation mechanisms in a hot strip mill. Several laboratory trials (Hot rolling simulator, cyclic oxidation) have highlighted important factors influencing corrosion of work rolls as well as helping the understandings of oxidation of a work roll in the roll bite and along the roll circumference in a stand. The attention is focussed on several elements present in water used in HSM for direct roll cooling (e.g. chloride, bactericides, sulphates, phosphates) and their effect on roll surface degradation. The second part of this paper is focused on the understanding of work roll oxidation along the roll circumference. The effects of roll composition, roll temperature, water composition and water temperature have been studied in order to understand the oxidation/corrosion mechanisms in a HSM.

Aug 16, 2017

By Rainer W. Kaiser

High wear resistant HSS rolls are being successfully used in the first stands of HSM finishing trains since the early 1990´s. The strong demand of mill administrators to make them applicable also in the last stands of the finishing rolling mill is a major influence factor of R&D efforts at respective roll suppliers. Looking back to the successful replacement of ICDP and HiCr rolls by more economic HSS rolls in F1-4 in regard to the TCO, rolling mill managers wish to repeat such scale gain also at F5-7 stands. Actually used enhanced ICDP rolls wear faster, being the HSM stoppage factor. F1-4 HSS rolls can be used for example 3 times longer. There is an obstacle to be overcome by roll suppliers and end users to replace F5-7 rolls by HSS rolls. Stick and crack resistance properties of HSS need to be improved. As a worldwide known leading producer of cast rolls for steel mills since 1820, the traditional German family owned foundry and machine shop IRLE, existing since 1693, accepted to face also this additional challenge. IRLE´s long year experience and prior researches have shown possible development directions to improve mentioned stick and crack resistance properties of its HSS grade, called SST. A new material of the HSS family is in the development pipe line and is discussed: SST/G. Choice criteria of the development direction, steps to control and guarantee respective sections of an industrial scale production as well as observations and results are described.

Jul 30, 2018

By R H. Sibson

Magmatic and/or hydrothermal fluid systems in island or mountain arcs self-organise to critical states subject to perturbation by changes in the regional stress, which plays a controlling role in the containment of overpressured fluids. Whether the magmatic arc is under compression (eg Andes, northern Honshu) or extension (eg Taupo Volcanic Zone, New Zealand) is a key factor controlling the ease of magmatic or hydrothermal fluid ascent. Abrupt changes in the stress regime have the potential to induce major episodes of fluid redistribution. Large earthquake ruptures along plate boundaries may induce such changes over broad areas, also contributing to fluid redistribution by renewing fault permeability along the causative rupture zone or reactivating distant fault-fracture permeability by shaking from radiated waves. High-resolution geophysical investigations of active arc systems and the subduction thrust interface underlying their fore-arcs reveal repositories of overpressured hydrothermal fluids. In active magmatic arcs under compression such as NE Honshu or Cascadia, there is evidence for a heterogeneous distribution of overpressured hydrothermal fluids in the middle-to-lower crust trapped around the base of the upper crustal seismogenic zone. Investigations of the subduction thrust interface responsible for great (Mw = 8.0) ‘megathrust’ earthquake ruptures has revealed in some instances (Cascadia, SW Japan) the existence of a belt of non-volcanic tremor (NVT) with accompanying slow slip episodes defining the base of the megathrust interface at 40 &#177; 5 km and 350&#176;C??-??550&#176;C. Aqueous fluid at these depths is likely derived from dehydration reactions accompanying the basalt-eclogite transition in subducted oceanic crust. NVT sequences in the hanging-wall above the interface may be defining migration pathways into the overlying crust.The potential for eruptive episodes in magmatic arcs and redistribution of hydrothermal fluids is assessed in the light of the stress changes that followed the 2011 Mw9.0 Tohoku subduction thrust rupture which extended along strike for over 500 km and down-dip for over 150 km, with maximum slip of c 50 m.

Aug 22, 2011

By M C. Schodlok

Banded iron-formation (BIF) and iron ores were measured using the CSIRO developed TIRHyLogger ™ to assess its ability to map quartz, carbonates and riebeckite. The TIR-HyLogger™ measures continuously spectral refl ectance data from diamond drill core or drill chips with a high spatial and spectral resolution. Samples from twelve BIF, bedded iron deposits (BID) and channel iron deposits (CID) have been analysed. The spectral data were processed with two different approaches. The first approach, focused on the identifi cation of the major minerals, was performed using principal component analysis (PCA). It identified four minerals (quartz, ankerite, riebeckite and goethite) and provided pure spectra called end-members. The second approach included a mineral diagnostic spectral feature extraction involving wavelength position, relative peak heights and relative depths of absorptions. Quartz has a diagnostic absorption at 8.625 µm and ankerite shows a refl ectance peak at 11.275 µm. In addition to the identified end-members, two carbonate populations (calcite and siderite) and two silica species (quartz and amorphous silica) were identified.

Jul 11, 2011