Search Documents

By G. Bylapudi, K. Mondal, J. Hirschi

ABSTRACT: Rock bolts are the main form of defence against rock falls in mines. Conditions under-ground are conducive to corrosion. A perception exists about American coal mines that bolt corrosion is not an issue, especially when bolts are fully grouted. This perception is not necessarily accurate due to the formation of micro-cracks as the resin sets and to subsequent rock movement that breaks the resin column’s continuity. Corrosion should be considered when designing rock bolt support in long-term excavations. This paper explores the problem of corrosion, outlines a method to determine the corrosion potential of bolts, and suggests ways to mitigate such effects.

Jan 1, 2010

By A. Holeyman

The displacement compaction piles described in the paper are installed using a heavy casing or tube and an internal drop hammer. The casing which initially is closed at the bottom by a sand plug displaces the surrounding soil during the driving. Additional sand is rammed down through the casing during the extraction of the casing. The applications and limitations of the method are reviewed in the paper. The importance of checking the sand compaction piles during and after the installation is stressed. Indications of the compaction of the surrounding soil during the driving can be obtained by comparing the initial and the redriving logs of the casing as well as from the volume of sand added. A method to estimate the increase of the mean cone resistance as measured by CPT tests in sandy and silty soils is presented. The governing parameters are the volume of the added sand, the granulometric index and the initial cone resistance.

Jan 1, 2010

Blast vibrations induce sounds within neighboring residences. A house wide vibration and sound monitoring system was installed in a West Virginia home which was subjected to blasts at varied distances and direction. Eighty-nine blast events were monitored and analyzed for this case study. Fifteen channels of data were collected including three triaxial geophones, one airblast microphone, one uniaxial geophone mounted to the wall of the house (response channel), and four microphones that recorded CD quality sound waves inside the house. Each of these channels was recorded on the same time reference and scale allowing for direct comparison of the waveforms. The response channel signal was easily separated into ground vibration induced and airblast induced movement due to the differences in their times of arrival. This response channel was then compared to the sounds recorded inside the home to determine which component of blast vibration induced the maximum sound response inside the home. Blasts at distances less than 762 meters (2,500 feet) had maximum sound responses from both ground vibration and airblast. While for blasts beyond 762 meters (2,500 feet), the maximum sound response inside the home was caused by ground vibration without exception. When airblast was identified as the dominant sound generator in the house, the peak amplitude of the sound was directly related to the amplitude of airblast. When ground vibration was identified as the dominant sound generator in the house, the peak amplitude of sound was not related to the amplitude of ground vibration. In these cases, sound amplitude was driven by the conditions present in the house such as loose items, doors, and windows creating sudden peaks from falling or slamming. In the same respect, sound amplitudes varied depending on where the sound was recorded. Different rooms generated very different sounds based on the contents of the room. Findings from frequency analysis showed that the frequency content of sounds inside the house were not related to frequency content of airblast or ground vibration regardless of source suggesting that residents would have difficulty determining the source of blast induced noise in their homes.

Jan 1, 2010

By S. Koppalkar

ABSTRACT: The development and evolution of the gravity recoverable gold (GrG) test procedure at McGill university is reviewed in this paper. Since the late 1980s, the research group led by the late Professor André Robert Laplante at McGill university has undertaken fundamental studies and applied research of the Knelson concentrator to develop a sustainable method of estimating GrG. Historically, a concept of “free gold” was used, and it was de?ned as the gold that could be separated and recovered from gold ore by amalgamation. Due to health and safety hazards, the practical use of amalgamation has declined. around 1994, a methodology using a 3-in Knelson concentrator to measure gravity recoverable gold was established at McGill university. as a result of more than 10 years of improvement and optimization, this technique has become a standard method of evaluating GrG for gold ores, gold plant streams and platinum group metals. By 2006, about 200 GrG tests were carried out at McGill universityon ores from all over the world. recently, a modi?ed version of the GrG test (a simpli?ed test) was developed to provide a quick and rough estimate of the GrG in a sample; this simpli?ed test has theadvantage of reduced mass, processing time and cost. to recognize and honour the contributions madeby the late Professor Laplante towards the establishment of a standard test procedure for assessing gravity recovery potential, the authors propose that the GrG test be named after Laplante.

Jan 1, 2010

By W. John Rankin

Professionals, technical and non-technical, working in the mineral and metal commodity industries need to understand the concept of sustainability and its implications for the industry. Undergraduate courses have not done this well in the past. Much has been written in this field, and there have been great advances in understanding. However, much of what has been published is superficial and sometimes misleading, and there is as yet no coherent, single account that can serve as an introduction or overview for mineral industry graduates. This paper presents an outline which can guide readers in developing an understanding of the topic and its relevance to their work. Key references are provided, particularly those accessible on the internet, which will serve to introduce the reader to the important principles and understandings. The guide should also be useful to academics preparing students to work in the minerals and metal production sectors.

Jan 1, 2010

By William P. Diamond

This report presents results of a cooperative research project between the U.S. Bureau of Mines and BethEnergy Mines, Inc. Four coreholes (two before mining and two after mining) were drilled at a longwall mine operating in the Lower Kittanning Coalbed to obtain coal and rock samples from over-lying strata to determine their gas content at various times in the mining cycle. The results of those tests indicate that 91 pct of the gas removed from the overlying strata came from coalbeds. Material balance calculations were made to compare the volume of gas produced both from gob gas vent holes drilled on the panel and gas removed by the mine's ventilation system with the volume of gas removed from strata directly overlying the panel to a height of 275 ft. This analysis indicates that only 40 pct of the total gas produced from the panel actually came from the strata directly overlying the panel. The remaining volume of gas production probably migrated to the longwall gob from overlying, and perhaps underlying, strata immediately adjacent to the panel and perhaps from greater distances downdip because of the establishment of a long-term pressure gradient in the study area.

Jan 1, 2010

By Q. M. Huang

In 1979 our company undertook the project of infra-structural work of White Swan Lake Hotel, (International class ) Guangzhou. Visit to the site showed that it was situated at the riverside, covering an area of 54,000 M2 with 30,000 M2 of which reclaimed from Pearl River. The material used for reclamation was black sand which was dredged from the nearby riverbed. The sand had the properties of high permeability and very low internal friction. The basement of the building was 6.2 m below ground level and 3 m lower than the riverbed. Apart from the pile foundation, a diaphragm wall was to be constructed prior to the commencement of excavation work for basement. A feasibility study was carried out to determine the method of construction which would maximize utilization of the plants and equipment that were available in the execution of the aforesaid foundation works. This report concerns only the construction of the diaphragm wall and the performance of the plants employed. A detailed delineation of the construction method is herein discussed

Jan 1, 2010

By M. Robson

Water & Earth Technologies, Inc. (WET), Habitat Management, Inc. (HMI) and Chevron Mining, Inc. (CMI) together developed a solution for reclaiming steep southwest facing slopes in mining Area 12C that have historically been prone to excessive erosion, low vegetation establishment and continuing maintenance. Area 12C is located in the east wing of the Chevron McKinley Coal Mine, 27 miles northwest of Gallup, New Mexico, on Navajo Nation land administered by the Office of Surface Mining (OSM). Mining in this area was completed in May of 2007. Challenges encountered for this reclamation project included the need to reclaim graded material on a slope of 18-35% with southwest facing aspect, the presence of undisturbed rock outcropping that needed to be avoided during reclamation, the operational need to limit bulldozer pushes and the inability to import or export additional materials for construction. Two different reclamation alternatives were considered for Area 12C. The first alternative would use a traditional reclamation approach including three levels of draining terraces designed to convey water on a 3% slope to a single riprapped down drain. Terracing and down drains have been used to reclaim areas with similar terrain conditions elsewhere at the McKinely Mine and have failed to adequately control erosion (Williamson 2006). Terrace overtopping and down drain blowouts have been issues in maintenance and functionality for the mine. Maintenance routines consist of cleaning out terraces where they have filled in with sediment and repairing damaged or blown out terraces and down drains.

Jan 1, 2010

The effect of rare earth element Y (0-2.0at.%) on the microstructure of TiAl alloys at the as cast and rapidly solidified conditions has been investigated. The results show that the addition of Y greatly refined the microstructure of TiAl alloys at both conditions. The refinement is more significantly with higher Y content. The refinement of Y in the cast alloys is attributed to that the strip-shaped Y-rich phase locating on the grain boundaries impedes the grain growth during solidification. In the rapidly solidified alloys, Y-rich phase dispersing uniformly as spherical particles in the matrix acts as heterogeneous nucleation sites which increases the nucleation rate of ??phase during the ????phase transformation, and produces a refined initial microstructure during solidification. Higher cooling rate restricts the grain growth during subsequent cooling.

Jan 1, 2010

By O. MacIntosh

The Round Mountain gold mine, located 90 km (55 miles) north of Tonopah, NV began large-scale production in 1977. During 2008 Round Mountain Gold Corp. (RMGC) relocated the primary crusher facility approximately 300 m (1,000 ft) to make room for the next phase of openpit mining activities. This facility was installed in 1988 and used a log-crib retaining wall and dump pocket. RMGC selected Hilfiker Retaining Walls and Collins Engineers, Inc. to provide design and materials for a new 17-m- (56-ft-) high mechanically-stabilized embankment (MSE) wall to support the haul trucks at the new location. The construction contractor was EarthTech West Ltd. of Norwood, CO. An MSE wall with a cast-in-place concrete face was chosen as a durable, yet less expensive alternative to the reinforced concrete dump pocket that was originally designed for the project. The arrangement of the MSE wall is of an unusual configuration to meet a variety of operational and maintenance requirements. This paper outlines the selection process, design and construction of the MSE wall.

Jan 1, 2010

By K. R. Griffin

New and developing communication systems enable underground miners to not only connect to the surface from an increased communication coverage area but also to be discovered in the event of an emergency. Communication and tracking systems are required by MSHA regulations, aiming to enhance health and safety and routine production in underground operations. Modeling a mine?s potential communication coverage area will increase overall coverage and efficiency of the communication network itself. Modeling the propagation of wireless communications enables ideal broadcast locations to be found when designing a communications network. Strategic placement of broadcast devices results in a reliable communication network that can better withstand disruption in both daily operation and emergencies. This paper will discuss recent regulatory developments in underground coal communication systems, the implementation of these new technologies, and how communication system?s networks can be modeled and analyzed using computer simulations.

Jan 1, 2010

By M. Reda

Because of the adverse environmental effect of Chromate, Molybdate ions had been investigated as replacement for Chromate and the results had shown not to be encouraging. Film deposited from peroxopolymolybdate (from reaction of Molybdenum meta, with excess Hydrogen Peroxide), are more robust than that deposited from molybdate solutions. This was shown to be due to higher fraction of Mo (IV) and Mo (V) that form from Mo (VI) in the peroxopolymolybdate deposited film than the film deposited from Molybdate solutions. The peroxopolymolybdate film contains 40% un-hydrated molybdic acid, tetraperoxodimolybdate and tetra peroxo tetra molybdate. The protective properties of peroxopolymolybdate were shown to be due to the effectiveness of the un-hydrated molybdic acid.

Jan 1, 2010

By N. L. Richards

In manufacturing for the 21st century, the first company to market often leads the pack in product development and sales. In this respect, manufacturing processes play an important role in transforming “raw materials” into a product(s) for sale to a customer. Thus it can be seen that upfront modelling of a design concept, or modelling of manufacturing processes in a plant, can play an important role in effectively ensuring the overall design and manufacturing route is carried out in an expeditious manner. In the paper various scenarios are considered with respect to modelling the microstructure and/or process, in various manufacturing processes. Also considered are the effects of service condition on the manufactured product in terms of creep and fatigue.

Jan 1, 2010

By Amir Asadi

Various damage modes that evolve with time in polymer composite laminates, such as transverse cracking, vertical cracking, delamination, and fiber fracture, as well as the interaction among them, influence the time-dependent degradation in modulus (creep) and strength (creep rupture) of polymer composite laminates. This study is focused on modeling the time-dependent evolution of transverse cracking in [90] plies of a multidirectional polymer composite laminate [0m/190n]. This model uses a two-dimensional variational analysis to determine the stress state at any given creep time. The elastic stored energy, determined using this stress state, is compared with a critical energy for fracture to determine the crack evolution with creep time. Model predictions are compared with experimental results to validate the model.

Jan 1, 2010

In early June, Rio Tinto?s chief executive officer Tom Albanese said that he expected demand for iron ore, aluminum and copper to double in the next 15 years. Driven by global industrialization and urbanization, Albanese said during his company?s annual general meeting that to meet the demand in 2030, the additional supply required will be equivalent to replicating the iron ore output of Australia?s Pilbara region every five years, adding another aluminum production complex the size of Canada?s Saguenay every nine months and developing another copper mine the size of Escondida, in Chile, each year.

Jan 1, 2010

By Timothy W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (?water box?) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 percent reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2010

By M. Ploc

The grinding process in the mining industry has seen an increased throughput to accomplish greater production and lower overall production costs. Up to 8-9 MW, a single motor can be connected to drive the mill through a pinion and ring gear. Above the single-pinion drive limit, the dual pinion approach was developed to allow two drive motors to be used. This allowed the mill input power to be increased to 16-18 MW. Recent developments in clutch and ring gear materials and design are allowing greater input powers of up to 20 MW to be considered. To avoid damage to the ring gear by uneven load sharing between the two motors, it is critical that the two machines accurately share load. This is typically achieved by either drives capable of controlling load torque between motors or using a GE proprietary control system that accurately controls the load torque from each motor.

Jan 1, 2010

By D. H. Garcia

The mining industry responded to public concerns about use of cyanide by developing a voluntary certification to allow companies to demonstrate their commitment. The International Cyanide Code (Code) establishes standards for the manufacture, transportation and use of cyanide. Key concepts in closure planning to comply with the Code are to decommission all facilities related to cyanide operations and to provide a financial assurance mechanism for those activities. Code requirements may differ from state-specific regulations, but requirements are based on closure goals for protection of the human health and the environment. Only issues related to cyanide operations are required to be included in decommissioning demonstrations. For example, the disposal method of cyanide solution holding tanks and the cost must be included in the closure plan, but information regarding closure of roads is not required. Closure costs must be based on a third-party contractor as opposed to internal budgets. Compliance with the closure requirements of the Code allows companies to show their stockholders, lending institutions, and the public that their operations are environmentally responsible.

Jan 1, 2010

1974 The Society of Explosives Engineers officially formed to “advance the art and science of explosives engineering” on August 20, 1974 in Pittsburgh, Pennsylvania.

Jan 1, 2010

By G. J. de Korte

South Africa is reliant on coal for the generation of almost all the electricity used in the country, and several large industrial concerns such as Sasol are also coal based. Research relating to the mining, beneficiation and utilization of coal is important in order to ensure the optimal exploitation and use of coal within the country. The Fuel Research Institute (FRI) of South Africa was established in 1930 to investigate all aspects of coal beneficiation and utilization in South Africa. The FRI went on to conduct world-class research and in 1957 a pilot coal preparation plant was constructed in Pretoria to enable large-scale practical experimentation. The pilot plant played a pivotal role in the establishment of South Africa?s low ash coal export project. Political and economic factors contributed to the eventual closure of the FRI and South Africa experienced a period of about 10 years between 1990 and 1999 during which very little public coal preparation research was done. This changed for the better towards the end of 1999 when Coaltech 2020, a collaborative research program was established. Participants included the CSIR, universities, the government and the major coal producers. Coal preparation research conducted under Coaltech thus far include dewatering and drying of fine coal, size classification of ultra-fine coal and dense-medium fine coal beneficiation. Currently, the Coaltech focus is on the beneficiation of low-grade coal reserves and is investigating existing as well as new techniques that can be utilized to provide cost-effective beneficiation of low-grade raw coals and reject coals.

Jan 1, 2010