Search Documents

By G Gibson

Realising that current roadway development performance levels were unlikely to sustain new generation high-capacity (15 Mt/a) longwall mines then being planned, the Australian Coal Association Research Program (ACARP) established a Roadway Development Task Group (RDTG) in 2005 to develop a research strategy targeted at improving roadway development performance in Australian longwall mines. The initial phase of the project identified a number of factors that differentiated best practice mines from others, and proposed a multi-faceted research strategy encompassing both short- and long-term research initiatives, including:conducting regular benchmarking studies across the industry to identify factors contributing to improved performance and to monitor performance trends,conducting regular industry roadway development operatorsÆ workshops to facilitate the transfer of successful roadway development improvement initiatives throughout the industry and facilitate networking between development practitioners,development of alternative skin reinforcement and containment measures that would eliminate the use of steel mesh and enable face support systems to be fully automated,development of automated bolting and mesh handling systems that would enable operators to be removed from the immediate face area,development of a body of knowledge of industry roadway development practice,development of a web-based information management system to capture and transfer emerging developments in roadway development practice and technology,reviewing the Australian civil tunnelling and underground metalliferous mining sectors to identify practices and technologies that could potentially be utilised to improve roadway development performance, anddeveloping a new generation high-capacity mining system capable of +10 metres per operating hour for 20 or more hours per day (CM2010). The paper reports on the progress of the above initiatives and outlines strategies to continue the pursuit for improved roadway development performance.

Jan 1, 2008

Operating metallurgists spend a significant part of their time running plant trials to compare two or more conditions in order to improve the process, such as a new reagent, flow sheet or piece of equipment. The best way to conduct such a trial is as a paired experiment when testing two conditions (eg 'old' and 'new') or a randomised block design when testing more than two conditions. These experimental designs should always be preferred over alternatives if their requirements can be met, because they block the effect of uncontrolled variables ('covariates') and are the most statistically efficient, ie they will lead to the required level of confidence in the outcome faster than other methods. Sometimes, however, it is not possible to switch condition easily, which is a prime requirement of these methods. In such cases the only option may be to switch condition once only, and compare the process performance before and after the switch. Examples are testing grinding media, large equipment, or long residence time processes such as leach trains or CCD thickeners. This paper considers some data analysis methods to deal with this situation. Modelling with intervention analysis (IA) uses regression models with a dummy variable to indicate the presence or absence of the test condition. IA with a time series model ensures that the residuals are uncorrelated. IA with a process model helps to deal with the problem of covariates. The reference distribution is a method free of any statistical assumptions but is less powerful than the other methods. Cusum charts are a helpful visual aid to interpreting time trends. A combination of these methods can help improve the confidence in the final decision. None are as good as a formal experimental design such as a paired trial.

Jan 1, 2008

By S Meffre, S Golding, K Zaw, J McPhie, R James, S Suphananthi

The Chatree deposit is located in the central portion of Loei Fold Belt, which extends from Lao PDR in the north through centralThailand to Cambodia in the south. Epithermal gold-silver mineralisation at Chatree occurs as veins/veinlets and stockworks with minor breccia in volcaniclastic and volcano-sedimentary rocks of andesitic to basaltic andesite composition and Permo-Triassic age. This preliminary oxygen isotope study mainly focuses on vein quartz of Au-Ag bearing mineralization (Stage 2) and a few samples of late Stage 4 quartz ¦ calcite veins. Quartz from Au-Ag bearing mineralisation has oxygen isotope values ranging from 8.1 to 12.3ë with the lowest values generally occurring at the deeper level (140 m below the surface). The late barren quartz ¦ calcite veins (Stage 4) tend to have higher oxygen isotope values ranging from 11.9 to 12.0ë. The oxygen isotope composition of the Chatree ore fluids were calculated at 250¦C, 300¦C and 350¦C based on homogenisation temperatures of fluid inclusions. The calculated oxygen isotopic composition of the Chatree ore fluid ranges between -1 and 6ë that overlaps with both meteoric and magmatic compositions. This shift in oxygen isotope compositions may relate to processes such as water rock-interaction and/or mixing of meteoric and magmatic fluids. It is interesting to note that the lowest quartz oxygen isotope values are spatially more or less confined to the prominent structures in the centre of the major ore zones. These structures may have been acted as conduits for higher temperature magmatic fluids. The quartz oxygen isotope values increase outwards from the centre of the main ore zones to the margin of the pits possibly due to mixing of magmatic fluids with lower temperature meteoric water. Whole rock oxygen and hydrogen isotope studies are in progress to investigate isotopic trends in the wall rock away from the ore zone. The systematic variation of oxygen isotopes in quartz from the mineralised veins and adjacent wall rocks could potentially be used as a vector to ore. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Max Gwynn, Tony Suckling

"The new Wembley Stadium is the most spectacular soccer stadium in the world, built to the highest specifications, using the latest technology and offering visitors an unrivalled match-day experience. Wembley Stadium is the home of English soccer, dating back to 1918 when the British Government began planning a British Empire Exhibition with a stadium as its centrepiece. The Empire Stadium, as it was originally known, was completed in 1924 in just 300 days and cost £750,000 ($1.4m). It was finally closed in 2000.The new Wembley Stadium, which opened in 2006, features fully covered seats for 90,000 fans and a striking arch that sits above the northern half of the stadium. With a span of 315 m (1040 ft), the 133-m (440-ft) tall arch is the longest single-span roof structure in the world. It supports the entire weight of the northern roof and 60% of the weight of the southern retractable roof. This means there is no need for columns within the stadium and ensures unobstructed views.Multiplex Constructions (UK) Ltd. employed Stent Foundations Limited to construct the £10m ($19m) foundations package for the new stadium. The scope of works for the foundation package included the design and construction of all foundations, including all main works piling, temporary works piles for the arch and roof, and tower crane piles. The scope also included trial piling and pile testing, setting out and removal of spoil.Piles were constructed by using bored cast-in-place techniques with both hydraulic and traditional crane-mounted rigs. Stent also installed sheet-piled walls at three locations to the site’s northern boundary. In addition to the main contract works, Stent constructed a £2m ($3.8m) contiguous bored-pile retaining wall within the demolition and earthworks package (Figure 1). This work was carried out as a subcontractor to Griffith McGee."

Jan 1, 2008

By J. J. Bezuidenhout

The waste-heat boiler is used within the Sulphide flash smelting process as the main dust and energy recovery unit. The large volume of off-gas discharged from the flash smelter is at a very high temperature (1350°C) and contains a significant dust load that subjects the downstream waste-heat boiler to tough and demanding conditions. The boiler cavity is especially prone to dust accretions, fouling, and corrosion caused by accumulation of molten particles and precipitation of sulphuric acid. Computational fluid dynamics (CFD) is applied within a qualitative study to model the flow and heat transfer distribution throughout the waste-heat boiler. The commercial CFD package, Fluent 6.2.16, was applied to a modified waste-heat boiler (23 m ×11 m ×5.4 m) within the Outokumpu flash smelting process. This investigation focuses on the geometric modifications to the typical boiler design, which includes elevation of the ceiling, placement of flow-obstructing baffles and radiation plates parallel within the flow path. Also investigated were various boiler operating conditions such as the circulation of process off-gas, air leakage from the dust discharging hoppers and variation in inlet gas composition. The geometric modifications had the desired effect of increasing the volumetric utilization and therefore enhancing heat transfer between the boiler surface and the gas stream and dust segregation. Introducing circulated off-gas at a rate of 20 m/s and at a 45° angle to the front of the waste boiler further enhanced cooling while reducing the high impact of the furnace-uptake gas-stream on the boiler ceiling. The placement of radiation plates was found to be very effective in enhancing the heat transfer surface and distributing gas flow within the boiler. These results present recommendations towards an improved waste-heat boiler design. Keywords: flash smelting, waste-heat boiler, CFD simulation, off-gas cooling.

Jan 1, 2008

By S. K. Kawatra

"A typical steelmaking facility produced 50,000 tons per year of slag in their hot-metal desulfurization process. This slag had a sufficiently high iron content that it could be beneficiated and recycled in a blast furnace, provided that the slag could be agglomerated into pellets suitable for use as blast furnace feed. In this work, beneficiated slag was agglomerated using both a conventional bentonite binder, and a fly-ash-based binder (FBB) that was formulated by the investigators. The FBB consisted of a combination of highcarbon fly ash with calcium hydroxide activator, allowing the FBB to exhibit binding properties when moistened. It was determined that beneficiated slag agglomerated with FBB had superior compressive strengths compared to slag agglomerated with conventional bentonite binder. The FBB is therefore a satisfactory method of binding the agglomerated slag. Since the fly-ash component of the FBB is commonly discarded as waste, this approach also provides a means for utilizing high-carbon fly-ashes that currently have very little commercial value.IntroductionIn 2006 approximately 72.4 million short tons of fly-ash were produce in the United States [1]. The majority of fly-ash which was used that year was consumed concrete, structural fills, and cement. It is also used in road base, aggregate, and other applications. However, 55.2% of the fly-ash produced in 2006 was not utilized and ended up being sent to a landfill. Essentially all of the land filled fly-ash could be a suitable binder for pelletizing desulfurization slag and other steel plant waste oxide materials. Fly-ash based binders (FBB) have been shown in laboratory studies to be suitable for producing iron ore concentrate pellets of equivalent strengths as those bonded with bentonite [2,3,4]. The utilization of highcarbon fly-ash within the market is important for reducing the volume of currently unmarketable and land filled fly-ashes. FBB would be a much cheaper alternative to the current bentonite binder or organic binders used for iron ore concentrate and would help to reduce pellet costs. Currently, transportation more than doubles the final cost of bentonite since it is produced hundreds of miles from the pelletizing plants, while fly-ash is produced from power plants located nearby pellet plants and steel mills. FBB’s also show promise for use in other high volume applications such as foundry sand mold binders."

Jan 1, 2008

By P G. Gaylard

P754 has been an unusual project in that its main aim was to develop a code of practice for metal accounting with the following key objectives:Development leading to an agreed industry standard at corporate governance level Significant improvement of the credibility of metal accounting from deposit to saleable product Development of guidelines for data collection, data analysis, reporting and audit A data analysis toolbox which provides go/no go testing for metal balance data Promotion of industry adoption of these guidelines to improve transparency and financial credibility. Over time, these guidelines may evolve into a code and eventually into a standard Develop and train engineers to become expert in metal balancing and reporting. Papers like this one and the workshop which follows this conference are part of promoting the code for adoption by industry. Developing a code of practice has traditionally been the provenance of professional bodies associated with particular industries û often on a voluntary basis. Given todayÆs industry pressures, it was felt that funding key input might accelerate the development process as well as offer opportunities to research some of the problems and to train some post graduate students in a difficult discipline. In fact, the project has brought together six industry sponsors from a wide range of process types, three research providers, and funded students in South Africa and Australia. The project has also attracted input from the financial community. A textbook to support the application of the code has also been written. The industry sponsors have made the Code and Guidelines available on request to help to facilitate its use by the mineral industry beyond the sponsor group. The Code and Guidelines have already been translated into Spanish and Portuguese which suggests that industry acceptance may happen quite quickly. The main thrust of the code is to integrate commercial and technical performance to a much higher degree. The Check in-Check out (CI-CO) method has been chosen as the vehicle for this combined approach. The mass and metal values used for CI-CO are 'absolute' and provide the basis of financial transfers. The CI-CO process occurs at each transfer of custody - whether between divisions within a company, or between companies. This approach means that measurement of mass and metal flows becomes the critical element of the process and that a quantitative knowledge of measurement accuracy and precision is also essential. This knowledge allows technical differentiation between differences which are within the expected margin of variation and those which must be formally identified as discrepancies and subject to a process of investigation and sign off. Hence, the application of the code for most companies should be more evolutionary than revolutionary, but with substantially more emphasis on measurement and definition of measurement error. Where this can be achieved, it should bring the mineral industry more into line with other industries competing for investment funds, community acceptance and future employees.

Jan 1, 2008

By Alex Naudts

Pre-excavation grouting is a predictable and reliable technique performed to prevent or minimize settlement in advance of, or during the tunneling operation. It safeguards the infrastructure above the tunnel alignment. Cement based suspension grouts and sodium silicate based grouts are frequently injected to consolidate and strengthen the formation and create a reinforced canopy above the tunnel trajectory. Grouting is typically performed through permeation and permeation in conjunction with hydrofracturing. Multiple injection passes through steel sleeve pipes are ideal, since they create an effective forespiling system to facilitate tunneling without causing unacceptable settlement, even with minimal overburden thickness. Ten pre-excavation grouting projects performed in the North America are discussed in this paper.

Jan 1, 2008

By W. James Marold

The New Croton Aqueduct (NCA) was the first major water supply tunnel for New York City. The 50-km (31-mi) long tunnel has 33 open shafts 6 m (20 ft) to 121 m (397 ft) deep. The tunnel and shafts are lined with brick and mortar, with cast iron lining and pressure covers in six pressurized shafts. Details of the 1895 construction are provided and compared to modern construction techniques. The paper provides rehabilitation techniques for the shafts and pressure covers, including grouting, epoxy lining, temporary bulkhead design and installation and placement of tremie concrete 98 m (320ft) below the water level in a 122 m (400ft)deep shaft using a Remote Operated Vehicle (ROV) to monitor the placement.

Jan 1, 2008

By Christopher Snee

??care has to be taken that the design is driven by sound geological reasoning and rigorous engineering logic rather than by the very attractive images that appear on the computer screen.??Hoek 1999 Design of a cavern is inextricably linked to the engineering geology of the site. The importance of sound geological reasoning will be illustrated by transportation projects in New York City where there are proposals for at least 11 caverns. These caverns have been the subject of advanced exploration techniques and geological interpretation but even so the raw data falls short of the sophistication of modern numerical methods. This paper will give geological explanations for the engineering characteristics of the rock in New York City which will provide guidance for practitioners when approaching cavern design in New York and elsewhere.

Jan 1, 2008

Coal preparation plant simulators are used to study flowsheet alternatives and determine product quality and quantity that can be produced under various operating conditions for individual circuits. Some simulators also provide an estimate of the cost per ton of clean coal by determining the number and size of different processing units required for a specific raw coal tonnage and by computing both capital and operating costs for individual units. However, to the authors? knowledge, none of these simulators have the ability to optimize plant performance while satisfying multiple product quality constraints and selecting the most profitable flowsheet from many alternatives. A novel coal preparation plant simulator (SIU-Sim) that maximizes the overall plant yield using a robust optimization tool and selects the best plant cleaning circuit configuration based on maximum plant profitability is presented. The simulator also identifies the best operating conditions for individual circuits of a plant to satisfy multiple quality constraints for the overall clean coal product. It uses a genetic algorithms- (GA) based technique to maximize the overall plant yield for each cleaning flowsheet alternative and uses a net present value (NPV) analysis technique to maximize plant profitability for the entire life of a new plant or the remaining life of an existing plant. The step-by-step development of the simulator along with a case study demonstrating its specific features is presented.

Jan 1, 2008

Fleet management systems have been adopted by many open pit mines throughout the world and the resulting improvement in truck cycle times has been one of the most significant contributors to mine efficiency. Ongoing enhancements to fleet management systems such as interfaces for vital signs monitoring have given incremental efficiency gains. Each incremental improvement is another step towards a grand vision of a totally automated mine. A relatively new fleet management system is being integrated with two other technologies to provide a highly reliable platform for a networked information system which monitors mine machinery and production. The paper reviews the integration project, the features of the new mine site information network platform and the contribution to productivity and safety. The new fleet management system has a predictive truck dispatch algorithm. It also has a distributed database that replicates rapidly so that each machine in the fleet has an identical database, thereby making each machine aware of other machinesÆ locations on the site. High precision systems for navigating and monitoring machinery such as drills, dozers, draglines and shovels provide individual machine operators with cockpit style real-time information to increase their operational efficiency. The integration of the new fleet management systems capabilities with the high precision systems that provide production information, machine vital signs data and operator information means that the mine operations and maintenance managers have real-time access to the whole mine siteÆs production data. Such a mine monitoring and reporting system is dependent on reliable wireless communications and reliable positions. Positions in fleet management and high precision systems for open pit mines are usually provided by global positioning system (GPS). Other global navigation satellite systems (GNSS) such as Glonass, and in the future Galileo, will provide additional satellite cover; however, some parts of open pit mines do not have enough sky visibility for reliable GNSS positioning and so a new centimetre level wireless positioning system called Locata is being integrated with the fleet and high precision systems to augment and backup the GNSS positions. The final integrated system will provide the highest levels of reliable position-based information to all stakeholders in a mineÆs operation, ensuring gains in productivity and safety.

Jan 1, 2008

By Colin Hardie, Simon Pelletier, Rakan Rhabani, Guy Comeau

"In order to improve the nickel concentrate thickener operation at Raglan Mine, two pulp deaeration cyclones were installed. These units obtained from Outotec Pty Ltd, also called the FrothBuster®, have been in continuous operation since mid-October 2006. The primary objective of the de-aeration cyclones is to lower the solids content in the thickener overflow by de-aerating the concentrate pulp before it enters the concentrate thickener. This dearated slurry should help decrease the nickel particle losses that report to the thickener overflow because of the flotation effect within the thickener.Optimizing the de-aeration cyclones has been a slow and ongoing process, however, initial testing is encouraging. The latest test results indicate a 50 % reduction (0.070 to 0.035 % solids) in nickel losses to the concentrate thickener overflow resulting in an additional $350,000 in annual revenues.This paper will present an overview of installing the de-aeration cyclones within a limited space, as well as the preliminary commissioning and testing challenges. This paper will also discuss the most recent concentrate thickener operating results since the de-aeration units were installed.INTRODUCTIONThe Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik Region has been in production since 1997. In early 2002, the concentrator implemented the Zero Process Water Discharge (ZPWD) project to recycle the process water to decrease fresh water consumption and reduce discharges to the environment. Due to this initiative, the chemistry of the process water changed significantly resulting in flotation concentrate streams, which were very frothy and difficult to manage. This phenomenon has resulted in operational challenges in many areas of the concentrator including slurry pumping, flow measurement and concentrate thickening.In October 2005, the Raglan Mine underwent a conversion from an AG mill to a SAG mill operation in order to increase throughput and to optimize key process areas. As part of this project, the first two North American pulp de-aeration (FrothBuster®) units from Outotec were installed to improve the operation of the concentrate thickener. The primary objective of the deaeration technology was to lower the solids content in the thickener overflow by de-aerating the concentrate thickener feed pulp. This in turn was to reduce the froth, which accumulates on the thickener surface, and more importantly reduce valuable nickel losses to the thickener overflow because of the flotation effect within the thickener."

Jan 1, 2008

Mining the Carpathia orebody at the Ardlethan tin mine in the late 1970s involved an innovative approach to underground mining which stretched the limits of drilling and blasting techniques. Holes of up to 95 m in length were drilled and blasted from the surface to extract an orebody which extended from 45 m to approximately 95 m below surface. This approach resulted in the elimination of an underground drilling sublevel, thus minimising the costs and hazards associated with underground drilling and blasting. Now, almost 30 years on, this method would probably still be the most appropriate choice.

Jan 1, 2008

Higher commodity prices and environmental considerations will make selective narrow-vein mining more attractive in future. Unfortunately, hand-held airleg (jackleg) mining is a mature technology that has safety and productivity limitations. Despite decades of attempted innovation, no obvious successor to airleg mining has emerged. A review of some of the possible technologies is followed by a speculative description of the mine of the future, intended to stimulate thinking and discussion during the conference.

Jan 1, 2008

By P Gardner

The Kanowna Belle gold mine in Western Australia has reached a depth of 1000 m on the way to 1300 m. A feasibility study undertaken in 2006 identified the mining of E-Block as both technically and commercially feasible. One of the major risks identified in the study was the ventilation capacity, as the existing primary ventilation system would not support the production schedule for mining and a major system upgrade would be required. Failure to provide the necessary airflow would put the project at risk. A review of the airflow requirements and infrastructure options detailed in the feasibility study was undertaken to ensure that the assumptions and design were optimised. This review recommended a minimum airflow of 206 m3/s, but by acknowledging the necessary constraints imposed by mining at depth and re-engineering the mine layout to optimise the primary ventilation circuit, this requirement was reduced to 160 m3/s. This represents a 22 per cent reduction in airflow and a reduction in capital cost that will see mining at depth become economically feasible at Kanowna Belle. This paper discusses the processes that led to a redesign of the mining layout and highlights the importance of including the ventilation network in the optimisation process.

Jan 1, 2008

During development mining, ventilation capacity may decrease and the ventilation requirements may depart from initially planned values depending on the mining rate, increases in the methane emission rate, and changes in ventilation airway leakages. Insufficient ventilation air quantities and the occurrences of high methane liberation rates can overwhelm the existing quantity of ventilation air and result in elevated levels of methane gas during development mining. This condition can both limit the development of that section and increase the risk for an ignition that may lead to an explosion. Thus, the prediction of ventilation air requirements prior to mining can enhance worker safety by reducing the likelihood that explosive methane-air mixtures form. This study presents an approach for prediction of methane inflow rates using coalbed methane reservoir modeling. For this purpose, a two-phase coalbed reservoir model of a three-entry type roadway is developed. In the model, grids are dynamically controlled to simulate development of entries. Examples are given for methane inflow and ventilation air requirements as a function of mining rate, development section length, mining height, and the existence of degasification boreholes. This technology can be used to limit the methane concentrations occurring as a result of the influences of various coalbed and operational parameters.

Jan 1, 2008

By D. S. Kieffer

Ground characterized by hard boulders embedded in soft matrix represents one of the most challenging conditions for TBMs, as the cutterhead must cope with the non-optimal conditions of cutting hard blocks while simultaneously excavating through soft, soil-like matrix material. Dowden and Robinson (2001) and Hunt and Mazhar (2004) summarize several case histories relating to the problems of advancing a TBM through boulder-laden ground and provide guidance with respect to appropriate site investigations and baselining strategies. Some rock types constituting boulder-laden ground include: ?Sedimentary Rocks?cemented alluvial channel deposits, colluvium/talus, landslide debris, and glacial till. ?Igneous Rocks?agglomerates, lahars, and pyroclastic deposits. ?Metamorphic Rocks?tectonic mélange and cataclastic fault zones. ?Decomposed Rocks?corestone bearing saprolites. Disc cutters are commonly utilized to cut the hardblocks; however, as compared to the understanding of disc cutter behavior in hard continuous rocks, little is known regarding fundamental cutting mechanisms in highly heterogeneous bouldery ground conditions. To advance this understanding, a suite of full scale tests have been performed using a linear cutting machine at the Colorado School of Mines (CSM). This paper summarizes the observed cutting mechanisms and their practical implications for TBM excavations through boulder-laden ground.

Jan 1, 2008

By Todd M. Ruff

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying methods to prevent workers from being entangled in machinery used at mining operations. An analysis of mining accidents in the United States that resulted in a fatality or permanent disability from 2000 through 2005 showed 438 severe incidents that involved contact with machinery or equipment, an average of 73 per year. Researchers determined that the most common machinery involved in these severe accidents was conveyors. Also, a significant portion of the accidents occurred during machine maintenance and repair. Researchers are focusing on improved methods to prevent unintentional machine startup during maintenance activity and methods to detect workers near moving machine components. One new technology that shows promise for this application is intelligent video. Popular in the surveillance and security industries, these systems use cameras and computerized video analysis techniques to automatically detect the presence of people in preset zones within the camera?s field of view. A preliminary study has been initiated to determine if this technology could reliably detect the presence of workers in hazardous locations near machinery. Possible advantages of the use of this technology include improved detection zone demarcation and improved ability to distinguish between hazardous and non-hazardous proximity, compared to conventional proximity sensor techniques. Initial tests to detect a person near a conveyor system in daylight conditions showed promising results. A description of the technology, test procedures and results, implementation challenges, and future research needs are discussed.

Jan 1, 2008

By Cem Akgüner

The displacements of axially loaded single piles are analyzed with an approach based on elasticity. Young?s modulus and Poisson?s ratio of the soil encompassing a pile are the unknowns required as input to obtain predictions based on the elastic method. Attention is directed towards Young?s modulus because the range and variability of Poisson?s ratio is not significant in displacement calculations. A database of axial pile load tests established for the California Department of Transportation (Caltrans) is investigated. All of the tested piles were driven into the ground. Measurements of displacements and loads were made only at the top of the pile. First the magnitude of displacements is determined up to loads that are half of the failure load measured from pile load tests. Various correlations for Young?s modulus are then employed to determine how accurately each predicts the actual measured displacement. The chosen correlations utilize the routinely available parameters of laboratory triaxial undrained shear strength for cohesive soils and standard penetration test blowcount for cohesionless soils.

Jan 1, 2008