Search Documents

By P Ottenio, B CarrT

In the last 40 years, the froth flotation process widely spread in the paper industry becoming the dominant technology for ink removal from recovered paper slurries and cellulose fibres recovery. Most of current models used to describe the flotation deinking process are based on hydrodynamic and statistical theories of ink particles collision/attachment to air bubbles. The complexity of these theoretical models, together with the variability of the recovered papers composition, does not allow to define a set of æeasy to handleÆ equations to be used for modelling industrial flotation cells. This main limiting aspect makes that, in several deinking process modelling tools, basic parameters used to characterise the flotation unit, ie yield, ink removal efficiency, water loss, are constant parameters. Although in some process simulation tools the flotation yield/efficiency is adapted to process control parameters (air ratio, pulp flow, pulp consistency), physicochemical variables (namely the pulp frothing aptitude, the pulp surface tension and the ink adhesion energy to air bubbles) are not taken into account to adjust the flotation yield/efficiency. Data collected during recent laboratory and pilot plant experiments focusing on the role of surface active substances on the flotation efficiency were therefore interpreted and used to identify general trends that could be described with simple semi-empirical models. A set of model equations using surface tension and froth removal height as main variables was then defined in order to describe the behaviour of a pilot flotation cell. Trends obtained during the dynamic simulation of the deinking pilot plant were in good agreement with experimental data obtained under similar experimental conditions, thus indicating that developed equations can forecast with good approximation the behaviour of a flotation deinking unit.

Jan 1, 2005

By Eric J. Foell

The Offshore Technology Conference (OTC) was founded in 1969 when a group of scientific and technical societies organized an annual conference and exhibition dedicated to technologies used in the offshore oil, gas and mining industries. Currently, OTC is sponsored by 12 industry organizations and societies. These include: American Association of Petroleum Geologists (AAPG); American Institute of Chemical Engineers (AIChE); American Institute of Mining, Metallurgical, and Petroleum Engineers (AIME); American Society of Civil Engineers (ASCE); ASME International Petroleum Technology Institute; Institute of Electrical and Electronics Engineers/Oceanic Society (IEEE-OES); Marine Technology Society (MTS); Society of Exploration Geophysicists (SEG); Society for Mining, Metallurgy, and Exploration (SME); Society of Naval Architects and Marine Engineers (SNAME); Society of Petroleum Engineers (SPE); and The Minerals, Metals, and Materials Society (TMS). OTC also has two endorsing organizations, the International Association of Drilling Contractors (IADC) and the Petroleum Equipment Suppliers Association (PESA), as well as 6 supporting organizations that include the American Petroleum Institute (API), the Independent Petroleum Association of America (IPAA), the Institute of Marine Engineering, Science, and Technology (IMEST), the International Association of Geophysical Contractors (IAGC), the National Ocean Industries Association (NOIA), and the United Kingdom Offshore Operators Association (UKOOA). From its earliest years, the OTC has been held during the first week of May in Houston, TX, initially at the Albert Thomas Convention Center where OTC?69 drew 4200 attendees and 200 exhibitors. As the conference grew and became established as the world?s foremost event for the development of offshore resources in the fields of drilling, exploration, production, and environmental protection, the venue was changed to the Astrodomain Complex, with technical paper sessions and most exhibits taking place in the Astro Hall. The numbers of attendees and exhibitors varied somewhat over the years, primarily in accordance with the fortunes of the international oil and gas industry. At its height in the early 1980s, OTC registered attendance exceeded 100,000 with more than 2500 exhibitors forcing expansion into the Astro Arena and even the Astrodome.

Jan 1, 2005

By N Winkelmann

Underground coal heating is a significant hazard in some coal mines. The broad principles of how underground coal heatings occur is reasonably known, however the technique for locating the heatings in often inaccessible goaf has been proved to be difficult. Since 2002, CSIRO, with the support of the Australian Coal Association Research Program (ACARP) has been undertaking investigations to apply and develop innovative surface-based radon technique for locating the underground heatings in Australia. This paper presents the progress of the investigation.

Jan 1, 2005

By J. Chae, D. Pecha, R. Andrews

The Henderson/ML King CSO Project is a major combined sewer overflow (CSO)reduction project for the Department of Natural Resources and Parks of King County, Washington. The central element of the project is the 3100 lineal feet long, 14'-8"diameter 42nd Ave S Storage/Treatment Tunnel. During the course of the project, the owner and consultants evaluated numerous elements of the tunnel including the alignment, geotechnical conditions, tunnel liner, and settlement monitoring requirements. The contractor utilized innovative shaft construction methods for the tunnel portals, and adhered to strict contract requirements in successfully constructing the tunnel. This paper provides an overview of the design and construction elements of the 42nd Ave S Storage/Treatment Tunnel that led to the successful completion of the project.

Jan 1, 2005

By Dana C. Reinke

Jan 1, 2005

By M S. El Salmawy

In order to develop the HF-free flotation reagent system, the main objective of this investigation was to study the possibility of separation of quartz from feldspar using non-ionic surfactants as the collector. The non-ionic surfactants used were polyoxyethyl cethyl ether (PECE) and polyethylene glycol monocethyl ether (PGME). The flotation behaviour of quartz and microcline with PECE and PGME was investigated. Each surfactant was a good selective collector for quartz with its recovery being influenced by pH and surfactant concentration. Quartz is floated favourably by both types of polyoxyethylene non-ionic surfactant whereas microcline was not so much. The floatability of quartz increases as the oxyethylene length of surfactants increases. Zeta potential measurements in the system of PGME/mineral were also carried out. It was determined that in the absence of PGME the points of zero charge for quartz and microcline should be approximately at pH 2.5 and 1.8, respectively. The addition of PGME to the system causes both minerals to become less negatively charged. Differences in the zeta potential value between quartz and microcline, in the presence of PGME, were detected. It can be suggested that the interaction of the oxyethylene group to the microcline surface should not be as strong as that to the quartz surface. In the mixed surfactant system of PGME and dodecylamine acetate (DAA), a small addition of DAA causes drastic enhancement of quartz flotation in the wide pH range of 1 ~ 10. In the mixed surfactant system selective flotation of quartz from microcline would be anticipated at pH

Jan 1, 2005

By N. C. Karmakar, Y. V. Rao, M. Aruna

No one can properly work without sufficient light and this is especially so in mines where conditions are difficult. Artificial lighting is very important for the night shift to provide a safe and efficient working environment, which must be evenly illuminated with no obvious dark spaces and a minimum amount of glare. During an illumination survey of a large mechanized surface mine, it was found that the illumination level varied and was not uniform throughout the length of the road; it was high at one side of the road instead of at the centre. There were also different combinations of lamps, with angles of light arm varying from 35º to 70º. In this respect, an experimental study was carried out with a fabricated telescopic light pole to uncover the optimum design parameters of lighting installations. The analysis was done by plotting isolux contours for fixed installations and drawing graphs for various combinations of luminaries, reflectors, light arm angles, and height of lanterns by plotting the horizontal angle of the light arm along the abscissa, and the contour area along the ordinate. The study revealed that the design parameters of the lantern are mainly dependent on the type of luminaires. It was revealed that the pot reflector with a combination of tubular bulbs produces a wide distribution of light, and contributes towards a reduction of luminaries when installed in longer roads.

Jan 1, 2005

By Geoffrey Fosbrook, Donald Phillips, Anil Parikh

The Second Avenue Subway is a $16.8 billion project planned by the Metropolitan Transportation Authority (MTA) in New York City. It will reduce overcrowding and delays on the Lexington Avenue Line, improving travel for both city and suburban commuters, and improving access to mass transit for residents of the East Side of Manhattan. The project is a new, two-track, 13.5 km (8.5 mile) subway extending from Lexington Avenue at 125th Street in Harlem on the north end of Manhattan, to Water Street at Hanover Square in Lower Manhattan. The first phase of construction includes rock tunnels from 92nd Street to 62nd Street and connection to the existing 63rd Street station, three new stations, and track and systems from 105th Street to 63rd Street, allowing service between 96th Street and Brooklyn via an existing Broadway Line. The following describes the Project in detail, discusses the construction challenges addressed in the design, and the initial design/build contract to be awarded in 2005. A discussion of the planned mined construction of two rock caverns and a cut-and-cover station construction are also included.

Jan 1, 2005

The management of safety has undergone a number of radical changes in the past 100 years. The most important paradigm shifts occurred through the work of Heinrich, followed by the advent of the safety systems era and, more recently, the behavioural safety approaches that have become increasingly popular around the world. Each of these æapproachesÆ to safety has left an indelible mark on the way we target safety improvements, helping decide which interventions are deployed and how they will be measured. They have also resulted in a number of æmythsÆ about safety management, each of which will be discussed, analysed and challenged in this paper. This paper highlights the complex problem of æcomplacencyÆ, that has arisen out of the increased levels of regulation and consequent perceived protection that workers enjoy in the work place. It also looks at a phenomenon called æaccident migrationÆ which results from a superficial treatment of accidents with changes to rules and procedures. The most recent approach to safety is generally known as behaviour-based safety, which flowed from the human sciences and quality management era. This approach has had a dramatic impact on the way safety is managed around the world, but still falls short in a number of key aspects, most notably the area of risk awareness and risk understanding. Many workplace accidents occur simply because the risk is unidentified, underestimated, not understood or ignored. This paper proposes a new direction for safety, called competency-based safety. It is based on cognitive psychology aimed at combating the consequence of modern protection. A case study is presented detailing the deployment of this approach throughout Placer Dome.

Jan 1, 2005

By Zeynep Aktuna

In this study, the formation of zeolites around Kizkapan and Karlikoy villages (Sothwest Kesan) were investigated. In this region, stratigrafically, Upper Eocene Kesan Formation, i.e. sandstone and rarely shale are observed at the bottom. Early Middle-Oligocene Yenimuhacir Formation is composed of sandstone, marl and tuffs. The zeolitisation is determined in the dasitic tuffs of the Yenimuhacir Formation. In this tuffs' zone, alteration had primarily resulted in zeolites, mainly mordenite, heulandite-clinoptiIolite. Silicification and alteration to clay minerals are also common. The Miocene-Pliocene Ergene Formation and alluvium deposits are the top units in the area. In the studied area, zeolite occurences have economic importance. The results show that successively rapid and short term periods are responsible for the clinoptilolite-heuylandite formations. The homogene chemistry of the solutions may be evaluated for a possible successive zeolitisation period. Multi-periodic vocanic activity and also circulation of thermal water had resulted in a continous dissolution of volcanic glass; moreover, resulted in the formation of suitable conditions of zeolite formation. The mineral crystallization sequences and alteration products as zeolites within the wall-rock, circulated solution reaction depends on a serie of parameters such as chemical composition of both initial materials and volcanic solutions during rock¬solution interaction period. The previous researches and the chemical studies support our results and observations in the studied area. The aim of this study is to investigate the presence of zeolitisation and to explain the formation steps of zeolitisation in Kesan Area by considering the content and distribution of major and minor elements determined in zeolite bearing tuffs. The chemical structures of both zeolite bearing volcanics and zeolite minerals are compared to the results of previous studies. Two dimentional behaviours of major and minor elements were discussed in order to caracterize zeolitisation development and to postulate a probable formation type of zeolitic alteration.

Jan 1, 2005

By Ke Yang, Robert Liang

"Drilled shaft foundations are widely used for many types of structures, especially for highway bridges, high rise buildings, and costal structures. The lateral design considerations are crucial for those structures that are subjected to lateral thrust forces, winds, waves, and earthquakes. The p-y analysis is the most widely used method for the analysis and design of drilled shafts for lateral load applications in soils. However, existing p-y criteria were developed based on the lateral load tests on small diameter drilled shafts in soils. Although, a lot of lateral load tests have been conducted, there are a limited number of lateral load tests on large diameter drilled shafts embedded in clay. In this paper, a lateral load test on 2.44 m diameter fully instrumented drilled shafts in clay is presented. The site specific p-y curves are derived based on strain gage readings. The existing p-y curves are found to be much softer than the site specific p-y curves. Correspondingly, the deflection at the top of the test shaft under the maximum applied load is predicted to be eight times larger than the measured value using existing p-y criteria. A new p-y criterion is proposed in this paper. The proposed p-y criterion is proven to be able to capture the site specific p-y curves of the load test and to predict closely the deflections at the top of the test shaft. INTRODUCTIONDrilled shaft foundations are widely used for many types of structures, especially for highway bridges and costal structures. The lateral design considerations are crucial for those structures that are subjected to lateral thrust forces, winds, waves, and earthquakes. Although efforts have been made on studying lateral response of drilled shafts; nevertheless, only limited studies have been published on the behavior of large diameter drilled shafts under lateral loads and the corresponding design methods."

Jan 1, 2005

By R N. Lamb, A N. Buckley

Experiments have been carried out to establish whether time-of-flight secondary ion mass spectrometry (ToF-SIMS) is able to differentiate monolayer and multilayer coverage of thiol collectors on sulfide minerals. The systems investigated were those for which x-ray photoelectron spectroscopy is able to provide an independent determination of the extent of coverage, and included diethyldithiophosphate (DTP) and 2-mercaptobenzothiazole (MBT) on chalcocite, DTP on Ag2+MS prepared by sulfidising metallic silver, and isobutyl xanthate (BX) and MBT on galena. For monolayer adsorption of MBT on chalcocite, peaks from MBTû but not Cu(MBT)û ions were evident. For multilayer coverage, Cu(MBT)2û ions were clearly present, notwithstanding the fact that other data had identified the principal multilayer species as Cu(MBT). For adsorbed DTP on copper and silver sulfides, DTPû and metal(DTP)Hû peaks were observed for monolayer and multilayer coverage. Although the multilayer species was expected to be predominantly metal(DTP), metal(DTP)2û ions were evident for multilayer (but not monolayer) coverage. For the PbS/BX system, intact Pb(BX)2 or Pb(OH)BX ions were not detected for multilayer coverage, although Pb-containing ions heavier than PbBX were. Indeed, for all the systems studied, ToF-SIMS was able to differentiate monolayer from multilayer coverage. In general, however, the SIMS evidence alone might not be sufficiently definitive to effect the differentiation. In the case of collector adsorption on copper and silver sulfides, if the multilayer species detected had been the metal monothiolate only, and had not involved the formation of some metal dithiolate, then ToF-SIMS might not have been able to provide an unequivocal differentiation of the two coverage conditions.

Jan 1, 2005

By A D. Bugarski, G H. Schnakenberg Jr

An investigation was carried out at a US underground mine to characterise diesel aerosols and to asses the effects of various control technologies on the concentrations and properties of particulate matter and gases emitted by heavy-duty diesel-powered equipment. This study was dedicated to evaluating the impact on mine air quality of contemporary diesel particulate filter (DPF) systems installed on mining equipment. Additional efforts were made to assess the effect of blended biodiesel fuels, yellow grease and soy, ultra-low sulfur fuel, a fuel emulsion and of selected diesel oxidation catalysts on air quality and emissions. The carbon analysis performed on the collected samples showed that the tested DPF systems reduced the mass concentrations of elemental carbon in mine air by between 70 per cent and 92 per cent. In addition, TEOM measurements, collected during these tests, showed that the total diesel particulate matter concentration in the mine air was reduced by greater than 65 per cent when DPF systems were used. The tested biodiesel blends were found to reduce elemental carbon concentrations in the mine air by between 49 per cent and 33 per cent, for the B20 (20 per cent biodiesel/80 per cent #2 diesel) of soy and yellow grease respectively and between 66 per cent and 56 per cent for the B50 (50 per cent biodiesel/50 per cent #2 diesel) of soy and yellow grease, respectively. The water-in-diesel fuel emulsion was shown to reduce elemental carbon concentrations by as much as 85 per cent. NO2 measurements showed an increase in the maximum concentrations of NO2 when catalysed DPF systems were used instead of mufflers.

Jan 1, 2005

By William Stewart, John Tinkler, Gary B. Hemphill

Of the 345 km long Taiwan High Speed Rail Project, connecting the cities of Taipeiand Kaohsiung, the 23 km alignment on Contract C230 required the construction of5755 m of shallow mined tunnels ranging from 137 m to 1285 m in length. All nine of these tunnels were mined using NATM methodology. On September 6, 2002, a collapse occurred in Tunnel T08 that affected approximately 50 m of tunnel. There was little warning. However, the crew was evacuated approximately 45 minutes prior to failure and thus, no injuries or loss of equipment. This paper will discuss the mining methods, jet grouting ground support, and the instrumentation selected for the rehabilitation and monitoring of the tunnel.

Jan 1, 2005

By O N. Antzutkin, W Forsling, K J. Pike an

The adsorption mechanism of three different O,OÆ-di-alkyl-dithiophosphate (dtp) collectors, K[S2P(OR)2] with R = Et, i-Bu and i-Amyl, on the surface of synthetic chalcocite (Cu2S) was studied by means of solid-state 31P CP/MAS NMR spectroscopy. The morphology changes on the conditioned Cu2S surfaces, in the collector concentration range 0.1 - 10 mM, were also monitored with scanning electron microscope (SEM). In order to assign Cu(I)-dtp species on the surface of Cu2S, the corresponding bulk Cu(I)-dtp compounds, which are clusters of the monovalent copper containing either Cu6(antiprismatic) or Cu8(cubic) cores, were synthesised, and characterised by means of solid-state 31P CP/MAS and static 65Cu NMR. Further investigations on the crystal habits of the bulk systems were carried out by powder x-ray diffraction and SEM. A comparative analysis of the 31P chemical shift and chemical shift anisotropy (CSA) data estimated from the experimental NMR spectra of the polycrystalline bulk Cu(I) dialkyldithiophosphate complexes was used for assigning the 31P resonance lines in the NMR spectra of the collector treated Cu2S powder samples. The species formed on the synthetic Cu2S surfaces were assigned to polycrystalline phases of: Cu6L6 with L = Et2dtpû, Cu6L6 and Cu8L6(S) with L = i-Bu2dtpû, and Cu8L6(S) with L = i-Amyl2dtpû. A heterophase autocatalytic step process of both formation and growth of solid CuxLy (L = R2dtp, x = 6 or 8 and y = 6) complexes on the collector treated Cu2S surface is proposed. A possible role of the oxidised form of dithiophosphate collectors, bis[di-alkyl-thiophosphoryl]-disulfane (disulfide), is discussed in terms of a specific self-redox reaction. The second order quadrupolar lineshapes in 65Cu NMR spectra were simulated and the interaction parameters, CQ and hQ, for the bulk dialkyldithiophosphato-copper(I) complexes were obtained.

Jan 1, 2005

By J J. Cilliers, K Hadler

Froth structure and stability are known to play important roles in determining mineral flotation recovery and selectivity. However, measuring froth stability in a consistent manner remains a significant challenge, especially at an industrial scale. Following preliminary tests on a copper concentration plant, a quantitative dynamic stability measure is investigated in this study in order to extend the results over a wider range of conditions and on a different orebody. The technique is based on the Bikerman foam test and uses a non-overflowing froth column to quantify froth stability. Experiments were carried out using an automated version of the froth stability column under different operating conditions. Air flowrate was the key operating variable. Tests were reproduced on a single flotation cell of a Platinum Group Metals concentrator. The froth stability factor, , was measured for each operating condition, and compared with the air recovery in the cell, , which was measured using image analysis. The froth stability column results gave the same trends as image analysis. In particular the froth stability factor was found to be linearly related to the actual fraction of air overflowing the cell. The metallurgical results clearly indicated that changes in air flowrate result in variations in flotation performance that can be attributed to changes in froth stability. The results showed that high froth stability conditions occur at intermediate air flowrates, and result in improved flotation performance. It is found that the froth stability column is a simple, cost-effective and reliable method for quantifying froth stability, and for indicating changes in flotation performance.

Jan 1, 2005

Researchers from the National Institute for Occupational Safety and Health's Spokane Research Laboratory installed Split-Set rock bolts instrumented with strain gauges to document the mechanical load response of the bolts in weak ground. Short-term monitoring of the bolts immediately after installation showed that some of the gauges went into tension. It was felt that the force exerted on the bolts to drive them into the hole should have caused the gauges to show compression. The tension probably resulted from the holes having crooked sections. Long-term monitoring over the course of a year also showed that the bolts were bending at some locations and that loads as high as 98 kN (22,000 Ib) were recorded along sections of the bolts. Load cells were placed on the head end of the bolts to determine head loads. Head loads up to 14.7 kN (3,300 Ib) were generated during bolt installation. In addition, closure readings were taken across the drift to determine the convergence rate responsible for bolt loading. A Rock Mass Rating (RMR) was calculated at the site to compare with bolt response. The bolts were installed as part of the rebolting process in an area being repaired because the near-vertical beds in the walls were buckling and causing the wall to fail. The instrumented Split-Set rock bolts will provide data that will lead to greater understanding of the behavior of the rocklbolt support mechanism. It may also be possible to explain the overall performance of the bolts in situ in terms of their design effectiveness. This work showed that load at the head of a Split-Set rock bolt was less than load along the interior of the bolt.

Jan 1, 2005

By J. C. van Dyk

The objectives of this study were firstly to characterize and quantify the inorganic material in the Secunda gasification feedstock. Secondly, the effect of washing on coal properties and sulphur content was investigated. Coal from a single source and a coal blend from 6 different mines were tested. Composite samples were visually sorted by a geologist in the groups containing roof, floor, C-shale, pyrite, carbonates and siltstone material. Inorganic mineral types from the single source and coal blends were characterized separately. Characterization results indicate that the average mineral matter distribution (mass %) of the coal tested was as follows: carbonates (6%), carbon-shale (19%), pyrite (12%), roof (18%), floor (46%) and siltstone (22%). The roof, floor, pyrite, carbon-shale, carbonates and siltstone in the single source and coal blend have similar chemical properties and characteristics, except for the ash melting temperatures of pyrite and kaolinite in the siltstone. By implementing selective mining and increasing mining management practices, the percentage discard in the run of mine coal can be significantly reduced, by up to 45%, if the mining of roof and floor material can be avoided. No significant impact of mining practices on sulphur content is expected in this case due to the low concentrations of sulphur in the roof and floor material. In summary, selective mining practices will probably result in almost45% decrease in the discard content in the run of mine to gasification, an increase in the carbon content from 55.0% to 58% (air dry basis) and a decrease in sulphur content from 1.1% to 0.9% (air dry basis). It is clear from this study that the main source of sulphur is not in the high ash-content mineral types (e.g. floor and roof), but in situ in the coal structure. Keywords: inorganic material, effect of washing, roof, floor, pyrite, C-shale, carbonates and siltstone

Jan 1, 2005

By M. Wu, G. Plascencia, A. E. M. Warner, A. Vahed, T. A. Utigard

Nickel oxide granules formed by pyrohydrolysis of a chloride solution, were reduced in hydrogen. Below 400 °C, an incubation period was observed, followed by very slow reduction. In the temperature range from 400 to 600 °C, the rate of reduction increased with increasing temperature and increasing hydrogen pressure. Microscopic analysis showed that in this temperature range the reaction followed the shrinking core model. Above 600 °C, the reduction rate decreased noticeably before suddenly becoming very fast at and above 950 °C. Microscopy showed inner bands of metallization inside the outer metallic rim, indicating partial blockage of the interface between the reacted and un-reacted NiO core. At these temperatures, particle agglomeration and sintering were also found to take place. Surface segregation of sulphur may account for the slow down in reduction rate above 600 °C. From an industrial point of view, reduction should be carried out from 550 to 600 °C with as high a concentration of hydrogen as possible. If sintering and agglomeration are not of any concerns, reduction can be carried extremely fast at about 1000 °C.

Jan 1, 2005

By M Lovitt, T Hewitt

The extraction of drawbells in Lift #2 at Northparkes Mines E26 orebody was achieved by single shot blasting, enabled through the use of electronic detonators. This paper discusses the designs considered at the time of the feasibility study and the various changes made to these designs prior to and during the construction phase of the Lift #2 block cave. Operational issues encountered are highlighted, as are ways in which these were overcome. The amount of personnel utilised to mine the drawbells is also covered. Lists of design and operational considerations to be used for drawbell extractions have been included.

Jan 1, 2005