Search Documents

By Subhas G. Malghan

Feldspathic deposits occur widely throughout the United States, but North Carolina, California, Connecticut and South Carolina accounted for over 80% of the total domestic feldspar output for the year 1973.1 Pegmatites and granites constitute the major feldspar reserves of the United States,2 and in addition, feldspar is produced as a by-product by firms whose major products are spodumene and mica.3 Feldspar is concentrated by hand-cobbing and flotation; the latter forms the major method of separating and concentrating feldspar. Feldspar flotation is practiced in the United States, Mexico, Finland, Norway, West Germany, Japan and the USSR. According to the U. S. Bureau of Mines estimates, the production of feldspar in the United States and rest of the world were 704,000 tons and 2,514,000 tons respectively. Feldspar is principally used as a flux in making glass, pottery, porcelain, enamel,-tile and other ceramic products. In recent years, the domestic feldspar industry is faced with a number of problems. As a result of increased cost of energy and the introduction in 1972 of new legislative programs relating to air, water, and noise pollution, land-use restrictions, and mined-land rehabilitation, the production costs have increased. Apart from the increased cost of operation, an operational problem exists with the feldspar producers in North Carolina, especially those in the Spruce Pine area. This problem is concerned with the use of hydrofluoric acid in the feldspar flotation. Feldspar producers in Spruce Pine, North Carolina have been discharging process waste water into the North Toe River. The mill waste water contains active fluoride ions. Fluoride in excessive concentrations is undesirable in waters used for drinking. It is stated that water

Jan 1, 1976

By D. L. Paulson

The Bureau of Mines is investigating pyrometallurgical and chemical methods for extracting copper from sulfide ores under conditions that provide for control of gaseous and solid emissions. Under this program, a new electrothermic reduction process was developed to produce blister copper after collecting essentially all of the sulfur by a single-unit operation. The process feasibility was indicated by a laboratory-scale investigation that demonstrated chalcopyrite concentrate can be roasted to less than 1 percent sulfur and that the resulting calcine can be reduced with carbon to blister copper by a cyclic process in a single arc-smelting furnace. Pilot-scale tests in an 800-kV-A electric-arc furnace demonstrated that 98.4 pct of the contained copper can be continuously recovered as metal by operating at bath temperatures between 1,350° and 1,375° C. Smelting rates of approximately 225 lb of blend ft2 of bath surface/hr resulted in power consumptions of approximately 520 kW-hr/ton of blend. The blister copper that was produced contained less than 0.1 pct iron while the precious metals reporting to the copper product and gangue material elimination were similar to those in a conventional smelting operation.

Jan 1, 1976

By Ivor E. Campbell

The Smelter Control Research Association, Inc. (SCRA) was established in 1971 by domestic primary copper producers to investigate processes for removal of sulfur oxides and particulates from copper reverberatory furnace stack gases. The Association maintains a continuing review of developments related to sulfur oxide and particulate control technology, and conducts pilot-plant-investigations of scrubbing processes with feed streams of copper reverberatory furnace off-gases. In its first year of operation, SCRA reviewed over 100 processes proposed for sulfur dioxide removal. As could be anticipated, the frequency of receipt of proposals relating to improvements in sulfur, dioxide control technology has now declined. However, the number of such proposals still being received indicates continuing research on both wet and dry scrubbing systems, and indicates a widespread awareness, of shortcomings of proposed control. Despite the fact that an almost unbelievable number of processes has been proposed for sulfur dioxide control, few have progressed beyond the conceptual stage, and only a limited few have been subjected to thorough pilot-scale evaluation. The most extensive pilot-scale and demonstration-scale investigations have been. devoted to the so-called throwaway processes employing limestone or lime slurry scrubbing. This work has, in turn, for the most part been on utility plant stack gases, containing from 500 to 3,000 ppm sulfur dioxide.

Jan 1, 1976

By Robert G. Lundguist

REAM is a unique and promising method of rock breaking using high energy, inert projectiles to impart mechanical energy to the rock. This paper describes a demonstration of the application of this new technology to two specific problems in open pit mining: secondary breakage and the scaling of loose material from pit walls. Under previous government contracts, Physics International Company developed the projectile impact method for a large variety of commercial and military rock excavation tasks. A 4 meter (13 foot) diameter by 16.8 meters (55 foot) long tunnel was driven at the Hope Valley Mine in the Sierra Nevada mountains of California in 1972 and 1973. An average of 1100 kg (1 ¼ tons) of a 172 MN/m2 (25,000-psi) granodiorite formation was broken by each of 590 shots used to drive the tunnel.l Based on these results it is estimated that REAM can drive over 60 meters (200 feet) of tunnel per day at about 88 percent of the cost of drilling and blasting. In addition, repeated axial impact by high energy projectiles was used to drill a 0.4 meter (16 inch) diameter horizontal hole in the same granodiorite formation. Each shot advanced the hole an average of 0.2 meter (8 inches).

Jan 1, 1976

By Allan Gebhard

The purpose of this paper is to summarize the role of water resource monitoring in mining activities and to discuss the considerations that go into designing and implementing a monitoring program. The design of a monitoring program is invariably based on sound engineering and scientific judgement since no design formulas exist that can be universlly applied to the monitoring of all activities. As discussed in this paper, however, a methodology of designing a water resource monitoring program does exist. In order to cost-effectively monitor the water resource impacts of mining activities, the following three monitoring related items should be understood: 1. the role of water resource monitoring in the planning, construction, and operational stages of mine development, 2. the available water resources monitoring methods and the proper role of each method in the various scages of mine development, and 3. the strategies that should be followed in designing and implementing a water resource monitoring program.

Jan 1, 1976

By D. Laguitton

The basic chemistry of a1•senic related to its dissolution and subsequent precipitation in gold-mine waste waters is discussed. The lime addition methods provides the most economic treatment of arsenical slurries, but requires a careful control of the oxidation of Asm into Asv, of the pH (>12) and the filtration of the precipitate. If arsenic levels below 0.5 mg/ l are required, a modification of the method by phosphate addition must be considered.

Jan 1, 1976

By M. J. Ferrante

The standard enthalpy of formation, low-temperature heat capacities, and enthalpy increments above 298 K were determined by the Federal Bureau of Mines for synthetic dawsonite [NaA1C03(OH)21. The enthalpy of formation was determined by hydrochloric acid solution calorimetry, with the result ?Hf°298 = -469.4±0.7 kcal/mole. The low-temperature heat capacities were determined from 6 to 307 K by adiabatic calorimetry. Tabulated are low-temperature values of Cp°, S°, and H.-Ho° from 3 to 298 K. The derived entropy at 298 K is S298 = 31.55±0.3 cal/deg mole. Enthalpy increments above 298 K were obtained by copper-block drop calorimetry. Tabular data of Cp°, S°, H°-H°298, -(G°-H°298)/T, ?Hf°, ?Gf°, and log Kf are given from 298 to 477 K. Enthalpies and Gibbs energies of decomposition are also reported.

Jan 1, 1976

By William C. Grady

The environmental and economic problem created by pyrite in coal are well documented. The removal of pyritic sulfur prior to, or during, utilization has been the object of considerable research, however, much of this research has proceeded without a proper knowledge of the microscopic occurrences of pyrite in coal. This paper investigates the forms, occurrences, and variations in the distribution of pyrite in major West Virginia coal scan. Twenty-nine samples from twenty-two major west Virginia coal scans were selected for this study (see Table I). The samples were selected so as to be representative of the major coal producing areas of the state. All samples, except five, were collected at active surface mines, as indicated in Table I, and all except one were channel samples. The time interval between sampling and preparation of polished microblocks varied from two months to two years, though most were prepared within three months of collection. Grinding, screen¬ing, and riffling of samples to obtain 250 grams of -20 mesh coal for microscopic analysis strictly followed ASTM procedure D2013-72.

Jan 1, 1976

[This Report represents the culmination of work perfomed under Contract No. .,JG1551A8 for the U.S. Bureau of Mine.The &apos;.:o-< embeded a site evaluation, engineering E:-y- ,, esign, and preparation of specifications for construction of a Transport Research 7 :4 (HTRF)The HTRF is designed as a research facility J evaluate the hydraulic transport of large lump coal at a prototype ;e scale. The HTRF is to be constructed and operated by the Pittsburgh and Safety Research Center of ;. re U.-AN a*, their Bruceton, Pennsylvania test center. In terms of technical capability, the HTRF will have transport pipeline:: of -, twelve-, and eighteen-inch diameter _&apos; with supporting coal handling n , water forage a.^ &apos;d conveyance, mixing, pumping, and dewatering equipment, plus instrumentation and controls. Maximum design velocity 13 20 ft/sec.; solids concentration, by, volume, will; 1 be a maximum-- of sixty, percent. Each test loop is designed to accommodate solids of up to one-third the diameter e - of the pine. The Final Report Pr.-&apos;I-rents information of t HTHF,. including the site evaluation, design criteria, a description of the a description of the procedure to be used for operation of the facility, an estimate of the cost to construct the f^Cilit:r, 1 p el_~lli.&apos;iU construe`, icn Schedule, and a construction suicJ_iicaT.l_ccn&apos;. T e c011SLr?Jc&apos;.ion soecl_ i.on _ccnta_i:s technic.&apos;..i re7,uir: (-n`,s for !&apos;urr1S~ &apos;~latcr..al. and ec-uipr,ent for :":C1 C_`:_C ti on of ti,_ H ice&apos; u:&apos;.:i ._II u s(-.6 for ~.Iir: .3!7 soliciting bids. `.l_o included n cc&apos;;,art_- c?r~.air sV:et..: :s ^nd rr^.?]

Jan 1, 1976

One of the responsibilities of the Melbourne and Metropolitan Board of Works is to provide a sewerage system for the metropolis of Melbourne which now contains over 2.5 million people. In providing this sewerage system it was necessary for the Board to embark on a large tunnelling programme some 20 years ago. As a result of this extensive tunnel construction programme, tunnel boring machines and shaft sinking methods have been developed to cope with the soft ground and soft to medium rock found in the southern and eastern areas of Melbourne where the majority of the recent tunnelling has been carried out. While in the last few years radical changes in construction methods have not been made, development has continued and improvements have been made, which have enabled the Board to extend the limits of the ground conditions in which it can efficiently construct shafts and also tunnels with boring Machines.

Jan 1, 1976

By John J. Dran

The elaborate analytical techniques for risk analysis used by the large mining companies in conjunction with the valuation of mineral reserve sites are totally inappropriate for the small miner. The small miner does not possess the financial and technical resources which are available to the large companies for such risk analysis. Even if these resources were available to him, the relatively small size of his investment would not justify a huge expenditure for risk analysis. What is required by the small miner is an improvement over the single point estimates provided by the valuation techniques that he currently uses. Such improvement should provide an indication of the extent to which the true value (known only after the fact) might differ from his estimated value of the mineral reserve site. In addition, a rough indication of the chance of occurrence of various differences between the true and estimated values would be helpful to him. These improvements must be obtained at low cost to be useful to the small miner. Such improvements would have to be based on a simple system requiring very few additional estimates by the miner. The small miner is not accustomed to dealing with sophisticated risk analysis techniques. Hence, any complex, time-consuming approach would be doomed to disuse or possible misuse. A simple, uncomplicated approach requiring a minimum of additional estimates by the miner can be based on a system devised by Frederick S. Hillier Although Hillier&apos;s method can be applied to various mineral reserve valuation methods used by the small miner, this note is specifically oriented to the discounted cash flow model. The basic discounted cash flow (DCF) approach provides a single point estimate of value and introduces the concept of risk (i.e. the possibility that the annual cash flows may differ from their estimated values and thus lead to an incorrect investment value) through the use of a risk-adjusted discount rate. This approach simply lowers the present value estimate with increases in the discount rate (i.e. increases in the risk assessment). The single point estimate still remains. Although the lower value estimate makes it less likely that the risky investment will be deemed profitable and undertaken, it provides no indication of risk that is suitable for examination and analysis. In addition to the "best guess" estimate of annual net cash flows required in the DCF model, application of the Hillier risk analysis model requires that the miner

Jan 1, 1976

Generate less respirable dust during mining by reducing the clogging and downtime of the water sprays on mining machines, especially on continuous miners. Approach An improved filtering system, having commercially available components, has been designed and tested. How It Works The improved filtering system shown opposite is mounted on the mining machine, where It traps particles of coal and pipe scale which cause most clogging of the water sprays. Water entering the system first flows through a ?Y" strainer, which screens out particles larger than 1/8 inch diameter. Next, the water whirls through a small hydrocyclone. Most of the remaining smaller particles are removed and pass Into the accumulator compartment built into the hydrocyclone. The water also flows through a final filter. This filter catches particles that might pass the hydrocyclone, especially during water spray start-up and shut-down, when the speed of the water flow is not sufficient for

Jan 1, 1976

By James A. Powell

A seismic system which utilizes in-mine geophones to detect trapped miners has been developed. Tests at the Bureau of Mines Safety Research Mine at Bruceton, Pa., and at two operating mines indicate such a system has a maximum detection range in excess of 1,000 feet. The system is fieldworthy and portable and requires less than 30 minutes to set up and check. Real-time detection is possible.

Jan 1, 1976

By Willard J. Tesch

The borehole surveying system described is used to measure ground movement over and near operating mines. The magnitude of any movement is con-trolled by the ground conditions, the mining method, and the mine progress. By correlating these factors with the measured movement, equations can be determined for predicting the effect of mine progress on the surrounding ground. These equations can also be used to predict the effect of mining a similar deposit with similar ground conditions. The borehole surveying system is used in cased boreholes to measure the inclination of the hole in two perpendicular planes. Grooved casing with an inside diameter of 3 inches is grouted in the hole. Two probes are used to obtain the data necessary to calculate the hole position versus depth. One of the probes contains a gyroscope, and the other contains a biaxial force-balance [s]ervoaccelerometer. Readings from the transducers in the probe are punched on paper tape by an automatic data acquisition system as the probe is pulled up the hole at 30 feet per minute by an electric winch. Readings from the inclinometer probe containing the accelerometer are used as input data to an on-line programmable calculator as they are punched on tape. The calculator computes preliminary results of the survey being made. The paper tapes obtained during the survey runs are later used as input to a computer that computes the offsets of the drill hole versus depth in true north-south and east-west planes. These offsets are printed for each foot of depth. Changes in these offsets between the first survey and subsequent surveys are a measure of the horizontal ground movement between the surveys.

Jan 1, 1976

By K. Fallenius

Since 1970 a new series of pneumo-mechanical flotation machines has been developed by Outokumpu Oy. The cells have a completely new type of mechanism based on a recently-developed theory of conditions necessary for dispersion of large amounts of air. The mechanism was developed in 3 cu m cells and scaled to 16 cu m cells. Rotor and stator description, scale-up theory, and practical experience with the 16 cu m cell are presented.

Jan 1, 1976

Coal mining in the Illawarra commenced in 1848. By the early twentieth century mining operations were spread over quite a distance along the coast centred on Wollongong. By this time there were already numerous tunnel mines and one shaft mine. Coal was first reported in Illawarra by Lieutenant Flinders on a voyage of exploration, southerly along the coast from Sydney in 1796. Because of the topography, particularly the escarpment and the narrowness of the coastal plain, access from Sydney was not easy by land and the normal access was by sea. It was not until some coastal areas had been developed for agricultural purposes that the mining of the seams on the South Coast commenced for the supp- ly of fuel. The most important mines in the early nineteenth century were Bulli and Osborne Wallsend. In general, coal was won from the tunnel mines and was transported directly, usually by tramway, to the nearest shipping point. Considerable hardship attended the earliest attempts at mining coal in regard to materials for mining and the way of life of the miners in the vicinity of the mines. With the growth of production and the installation of coke ovens at some mines the area, hitherto virgin bush- land, began to take on a more industrialised appearance. The mines were necessarily small,

Jan 1, 1976

By Maria I. De Rosa

High temperatures encountered by mine rescue teams during emergency situations may cause severe physiological strain, hindering the men from carrying out rescue and recovery missions. A prototype ice-cooling garment (ICG) was developed by the Bureau of Mines to alleviate physiological strain due to heat stress. The effectiveness of the garment was tested with acclimatized and unacclimatized subjects at a typical work rate (1,200 Btu/hr) expected during rescue operations and at various hot environments (97° to 113° F dry bulb and 80° to 89° F wet bulb). During exposures with the ice cooling garment, the subjects were able to maintain a safe deep body temperature of 100.4° F or below Without the garment, the deep body temperature rose beyond values of 100.4° F, a condition considered unsafe for continuous work in hot conditions. Both heart rate and skin temperature values were lower while wearing the ICG. Subjective observation also indicated a marked benefit by wearing the ICG.

Jan 1, 1976

By Ichiro Ito

At present, in Japan, the application of in-place leaching technique to the mined-out stopes has been carried out at two copper mines in a comparatively large scale. These mines are the Kosaka mine and the Tsuchihata mine, both are situated in the north-east district of Japan. At first, the author would like to tell about the in-place leaching operations and their results at these two mines. Then, the problems involved in the application of in-place leaching technique to the Japanese metal mines and the possibility of the future development of this technique in Japan are referred, too. Next, as to the research works, the author would like to explain briefly about some of the important results obtained in the recent studies on in-place leaching as well as on bacterial leaching in Japan.

Jan 1, 1976

By P. S. Capper

"Generally speaking, the most intensive efforts at dust control in the mining industry have, in the past, been concerned with underground operations and where uranium ore or high silica material is processed. In the past several years, Stoop Rock has made Intensive efforts to reduce dust levels in it's Iron ore pelletizing complex. There have been no great engineering break-throughs with regard to dust control in such plants, and certainly no new engineering techniques have had to be applied at Steep Rock. This paper deals with how significant improvements in dust levels have been achieved through minor modification to dust collectors and ventilation units, improvements in operating practices, and education of supervisors and hourly personnel.PROCESS DESCRIPTIONSteep Rock Iron Mines is located 120 miles west of Thunder Bay near Atikokan. (fig. 1) Run-of-mine ore is pelletized along with some -1"" concentrate that has been processed in the concentrator (a summer operation only), which utilizes gravity separation to upgrade a mechanical mixture of ore and waste."

Jan 1, 1976

By Y. Ueda, F. Noguchi, T. Yanagase

The rate of CaO dissolution into slag melts is of great importance in the field of pyrometallurgy. In this study the mechanism of CaO dissolution has been investigated by observing the melt heated on Pt-filament directly through microscope together with a help of X-ray micro analyser to find out a distribution of each element around CaO crystal. The direct observation reveals that the CaO dissolution tends to proceed by the action of molten slag entering between CaO crystal and newly formed 2Ca0. Si02 layer through cracks. The effect of slag composition on the formation of 2CaO- SiO2 layer will be shown as well as the effect of halogenides addition on the destruction of this compound layer.

Jan 1, 1976