Search Documents

By Claude Bodeving

The present steel economy drastically increases the financial strain on blast furnace operators. As a consequence, the importance of reliable cast floor operations is increasing drastically, which has a direct influence on the required clay mass and tapping equipment performances. When using modern high performance clay masses, pneumatic taphole drilling machines quickly reach their performance limits, which has made fully hydraulic drill hammers a standard in modern cast house operation. Besides the well-established hydraulic TMT hammers with high impact energy, an alternative version with lower impact energy, but high impact frequency was developed by TMT in the past, in order to achieve improved taphole protection. TMT’s recent research has shown that the drilling requirements inflicted by the taphole condition change over the taphole length, which has triggered the development of a new hammer, capable of switching between a high impact frequency mode and a high impact energy mode.

Aug 17, 2017

By Jefferson Lisboa Lelis, Marcos Roberto Soares da Silva, Maiara Rodrigues Gouveia

Nowadays, due the development of new hot rolled strips at USIMINAS, established the necessity of realizing studies to define new parameters for the welding machine of new pickling line, in order to improve mechanical and metallurgical properties of these materials. The aim of this study was to evaluate the weldability of high strength low-alloy steel with low boron content with tensile strength above 600MPa.The influence of energy input and preheating temperature on the mechanical properties of hot rolled strips were analyzed at three distinct thickness (2, 4 and 6 mm). To perform these evaluations were used tensile test, micro-hardness, metallography (micro and macro examination) and scanning electron microscopy analysis. In resume, a good welding performance was achieved, increasing preheating temperature and the welding energy higher than 60%.

Oct 13, 2019

By Michael Windhager, Karl H. Ziehenberger

ULTIMA® are high performance, centrifugal cast, double poured (CC duplex) work rolls. This paper describes the principle of the ULTIMA® roll concept and its wide range of usability. The ULTIMA® concept provides a solution for rod and bar mills to increase performance and output, even under harsh rolling conditions. The main focus is on highly loaded mill stands that require both high wear resistance and resistance against thermal fatigue, like pre-dog bone, dog bone, slitter. Specific case studies of quite different mill configurations and rolled product mix prove the positive impact on production yield, mill and roll shop operations, and profitability in terms of TCO (total cost of ownership).

Oct 1, 2019

By Ian James McDonald

Each year, approximately 400 million tons of blast furnace slag is produced worldwide with a tapping temperature of around 1,500°C. It is normally used as a substitute for cement clinker or as an aggregate material in road construction. Currently, the slag is granulated in wet-granulation plants using large volumes of water and to date, it has not been possible to utilise the remnant heat energy of the molten slag, which amounts to approximately 1.8 GJ of energy per ton. However, in an R&D project currently underway led by Primetals Technolgies and industrial partners, a new dry atomising technology is being investigated to use air to cool molten slag and recover the lost heat energy. The resultant pelletised slag fulfils the same criteria as wet-granulated slag for use in the cement industry. Phase 1 of the project has now been completed where a technical plant was set up at the University of Leoben in 2012. A series of dry-slag granulation campaigns were carried out using remelted blast furnace slag. The elevated offgas temperatures and the quality of the slag product as verified by the FEhS Building Material Institute have shown the process suitability as an industrial application and the decision was taken to escalate the project from large laboratory scale to a full size pilot plant. The phase 2 development of this plant is now underway and is scheduled for installation at the site of an industrial partner in early 2016 where full slag flow will be fed directly to the plant from Blast Furnace ‘slag runners. This paper will show the development path taken to date and the planned route to our goal in 2016 of being the first to industrialise the ‘game changing’ process of dry Slag Granulation with Heat Recovery from the slag.

Aug 16, 2017

By Renan Oss Giacomelli

The adhesion of multifunctional coatings on soft substrates is of paramount importance in the tribological behavior of this important class of surface treatment. In particular, scratch and indentation tests have been extensively used in order to assess this property. In this paper, the adhesion of a-C:H diamond-like carbon films deposited on nitrided low carbon steel was evaluated by indentation and scratch tests. The coatings were produced by PECVD onto 1020 steel substrates with two different surface finishing: ground (Sq = 0.184 µm) and polished (Sq = 0.002 µm). Indentation tests using a Rockwell diamond indenter were conducted and the adhesion evaluated by measuring the spalling region on images obtained by using optical microscopy. The analysis of the spalling regions produced semi-quantitative results, eliminating the subjective qualitative analysis proposed by the standard method VDI 3198. In addition, scratch tests were performed using the same indenter and a comparison between the two techniques was established.

Jul 31, 2018

By Sunil Katharia

In February 2016, the upgraded Blast Furnace 1 of JSW Steel Limited (JSW) at its Vijayanagar Steel Plant was blown in after a 6 months shutdown in which the whole furnace was rebuilt on the existing foundation and within the existing tower structure. Despite several plant constraints it was possible to increase the furnace inner volume by 85% - reaching 2307 m3 from existing 1250m3. The upgradation project covered the stockhouse and its dedusting system, top charging system, furnace profile, furnace cooling system, casthouse and its dedusting system, slag granulation plant, pulverized coal injection plant, hot blast system and gas cleaning plant – with major interventions in order to cope up with the changed operating conditions. The total scope of the project was split by JSW into several packages, all based on design data provided by Paul Wurth. JSW was responsible for coordinating the local subcontractors along with Paul Wurth which has been appointed as main technology supplier in charge of complete basic and selected detail engineering in the key areas and of the supply of core equipment such as the Bell-less Top®, copper staves, GCP key items and TMT casthouse machines. The main design concept and the key points of the project such as optimization of project ROI, advanced erection concepts as well as a summary of the operating results are presented confirming JSW “BF1” upgradation as one latest examples of the current state of the art in the revamping projects.

Aug 17, 2017

By Anderson José Beber

O trabalho apresenta os resultados da aplicação de um novo oxidante moderado em uma grande torre de resfriamento utilizada em sistema de geração de energia de uma grande usina no sul do Brasil. Esta torre de refrigeração utiliza água de efluente tratado (tratamento terciário Esgoto doméstico) como fonte de reposição. Com aplicação desta nova tecnologia, houve uma melhoria tanto no controle microbiológico como na taxa de corrosão. Além disso, a planta foi capaz de aumentar o ciclo de concentração, resultando em economia de água, produtos químicos e menor geração de efluente, possibilitando economia superior a R$ 500.000/Ano, aplicando conceito de reuso.

Oct 30, 2017

By Andrea Pezza

The paper describes the recent new installation and start-up of the second RH (Recirculation Degasser) in Rio de Janeiro plant of thyssenkrupp CSA Siderúrgica do Atlântico. The new plant is installed as part of the existing RH, the twin solution increases the overall melt shop production in the area of quality plates especially for deep drawing grades. With this new equipment, CSA is able to increase degassed grades production with a state of art asset that has the ultimate technology in operation, safety and automation. The description of the main components parts and the operational concept gives an overview of the latest experience in RH plant engineering combined with best operational practice of world class steel producer.

Oct 30, 2017

By Davide Onesti

Electrode regulation is the technology at the heart of the AC and DC Electric Arc Furnace. As such, in the last decade it underwent continuous improvement to maximize the EAF performances, in terms of process efficiency, machine utilization and operator safety. Given this background, Danieli Automation’s efforts in the field of electrode regulation have been focused on fast response to scrap cave-in, compensation of supply variations, automatic resonance detection, transformer protection, dynamic regulation of the electrical and chemical set-points, coordination and control of slagging and foaming agents, arc irradiance supervision. An extensive analysis of operator utilization and feedback was also carried out to develop an innovative system HMI. In this field, the choice of the variables shown to the user is the key aspect to allow a prompt process evaluation by the operator, who can refer to a condensed set of useful data. This paper will describe the innovative features and embedded models of the electrode regulation module (Q-REG+) and the supervision HMI, together with the effects of their application on EAF process efficiency and system usability.

Oct 30, 2017

By Filippo Verlezza

Conventional wire rod blocks have some limitations. They can only roll with fixed reduction ratios which always require the same rolling diameters within the block. With MEERdrive® SMS, as a pioneer, has introduced an innovative drive concept for wire rod blocks that can overcome the limitations of conventional solutions. The clue: the concept is based on individual drives for each stand position. The exigent wire rod market demand and the available technology melt in a new variant of MEERdrive®, the MEERdrive®PLUS, which represents a sizing block solution for finished size rolling and allows conventional as well as thermomechanical rolling. Further “one family rolling” is also possible, since all roll / size changes will occur in this block.

Oct 30, 2017

By Jose M. Rodriguez-Ibabe, Beatriz Pereda, Beatriz Lopez, Felipe Bastos

The modeling of austenite evolution during the hot rolling of steels is covered in the literature for a wide range of chemical compositions, although mainly for carbon contents below 0.20%. In addition, most research on this topic is oriented for processes that are characteristic of flat products. Compared to those processes, the hot rolling of bars for structural applications presents considerable particularities concerning mainly deformation, rolling speed and rolling temperature profile. Those particularities result in considerable changes on process parameters that affect the austenite microstructure evolution, both in the softening and hardening mechanisms if microalloying elements such as Nb is present. The aim of this work was to develop a model to predict the evolution of austenite microstructure that is suitable for the hot rolling of structural reinforcing bars. Different torsion tests simulating industrial schedules particular from those type of processes were performed. The tests showed the need to investigate Nb strain-induced precipitation interaction with softening mechanisms that can occur during the deformation schedule. At the end, the new proposed kinetics and routines were introduced to a program, MicroSim-Bars®, that is able to model austenite evolution under structural bar hot rolling conditions.

Oct 1, 2019

By Mingyu Ma, Lingling Liu, Liqing Chen, Houlong Liu

In this article, a 444-type heat-resistant ferritic stainless steel containing 0.05wt% Ce and 2wt% (Mo+W) was used as an experimental material and a study was carried out on the effect of rolling processes on the microstructures and texture evolution as well as on the mechanical properties and formability. The rolling processes contain hot rolling at different hot rolling finish temperatures, annealing after hot rolling, cold rolling and subsequent annealing. As for the hot rolling process, two hot rolling finish temperatures, 860 C and 770 C, were adopted, and their influence on the microstructures and mechanical properties was comparatively studied. The results showed that the microstructures after hot rolling and subsequent annealing could be refined by lowering the hot rolling finish temperature. The resultant microstructures after cold rolling and annealing were hereditarily refined. Lowering the hot rolling finish temperature can weaken the -fiber texture in hot rolled or cold rolled ferritic stainless steel strip. However, the -fiber texture was homogeneously strengthened by annealing the cold rolled ferritic stainless steel strip. Enhanced mechanical property and formability in terms of strength and average plastic strain ratio could be obtained by lowering the hot rolling finish temperature of ferritic stainless steel.

Oct 1, 2019

By Nishit Patel

Development work on the use of plasma torches in blast furnace ironmaking was completed in the 1980s. The technology developers planned to reduce blast furnace coke consumption using electrical energy and large scale coal injection through the tuyeres. Since this time, Westinghouse Plasma Corporation has improved torch reliability with industrial experience in solid-waste-to-energy facilities, as well as metallurgical applications. As coke makes up one-third of the hot metal cost, savings efforts frequently seek to lower coke consumption by increasing process efficiency or replacing coke with cheaper fuels. Alter NRG and Hatch assessed the merits of using plasma torch technology to superheat the hot blast. Coke rate savings, electrical purchase requirements, and a financial analysis to implement the torches are presented.

Aug 17, 2017

By Antonio Esposito

Saving energy and reducing resource’s consumption by minimizing emissions are today great challenges in the coking industry worldwide. In order to achieve satisfying results, equipment as well as technology should be continuously improved and designed to minimize the energy requirements and to maximize the recovery of materials and energy. The sensible heat in coke pushed out of oven chamber takes up 35 ÷ 40 % of energy consumption of coke oven. Usually the coke thermal energy is lost during traditional coke wet quenching, necessary to reduce the coke temperature for the storage and the following use in steelmaking processes. BPSL CDQ project is a sample how Paul Wurth’s technology allows to reach the energy saving goal and offers an alternative to traditional quenching. With the adoption of Coke Dry Quenching process, a considerable amount of this sensible heat in the coke can be recovered by producing steam; its production depends on various parameters, some of them battery related (Volatile Matters in red hot coke) and others CDQ system related (coke burning losses, superheated steam characteristics (i.e. P,T)), greatly depending also on boiler efficiency (heat exchange efficiency, insulation of the boiler itself, air leakage, etc.). The adoption of CDQ process reduces also the water consumptions in comparison with traditional quenching.

Aug 16, 2017

By Simon Chiartano

A global reflection on the design of blast furnace main runner was investigated in this paper. TRB Company used its skills and expertise to understand what the best option for this sensitive component is, including some innovative tools: intelligent block design for safety lining, thermal & thermomechanical numerical simulation, immersive measurement by thermocouples, IR thermal camera, 3D laser scanner.

Oct 1, 2019

By Ricardo Rodrigues Grizotti, Laudelino Cota Fonseca Junior, Marcio Basilio Xaviere

O projeto tem por objetivo desenvolver a padronização e implantação de um Modelo de Governança de Planejamento e Gestão de Estoques de MRO (Manutenção, Reparo e Operação) bem como um Modelo de Reposição baseado em políticas e modelos quantitativos, estatístico suportado de ferramental sistêmico desenvolvido no ERP SAP da companhia que incorpora Práticas de Planejamento e Gerenciamento, para melhor determinação dos Estoques e Nível de Serviços dos Materiais de Natureza MRO visando a otimização e balanceamento dos níveis de estoque com aumento do nível de serviço; redução do stockout; oportunizar a otimização dos tamanho dos lotes de compras para cada SKU; otimização das políticas de reabastecimento para cada classe de SKU e desenvolver indicadores e desempenho para monitoramento e controle do processo de planejamento e gestão dos estoques de MRO. O desenvolvimento, construção e implantação do projeto foi pautado e realizado através do uso da Metodologia Lean Six Sigma e suas ferramentas advindas do DMAIC - (“Define”, “Measure”, “Analyse”, “Improve” e “Control”), como uma estratégia gerencial planejada, com foco nos resultados de qualidade e financeiros, com o objetivo de promover mudanças significativas na empresa, buscando sempre melhorias nos processos, produtos e serviços oferecidos aos clientes.

Oct 1, 2019

By Alberto Pesamosca

The paper presents the results obtained by the AC EAF supplied by Danieli at Kroman Çelik (Gebze-Turkey) after the planned upgrade to 150 ton. The EAF – 7,4 m diameter, based on the full platform standard design - is able to handle a maximum power of 114 MW and is equipped with the most advanced and reliable technology, including module injection system and the Hireg electrodes regulation system. Excellent results were already obtained with 120 heat size in terms of fast start-up and excellent performance figures. After the upgrade, productivity was increased up to 212 t/h, maintaining high process efficiency (365 kWh/t with 32,1 Nm3/t O2).

Jul 30, 2018

By Luis Acainas Caballero, Karl Hoen, Stephan Krämer, Christoph Klein

The situation of the steel industry is still challenging. Worldwide overcapacities have an impact on profitability. More than ever, the point at SMS group is to provide the steel industry with flexible and profitable technologies and systems over the whole process chain. One example for that is the thin slab casting and rolling technology and, in particular the CSP® technology (Compact Strip Production), being well established for hot coil production. From its introduction in 1989, CSP® technology has been continuously further developed. Today, on a CSP® plant, the full range of high-quality steel grades can be produced with tightest geometrical and metallurgical tolerances under optimal economic conditions. With the introduction of semi-endless rolling and, as a further step, the endless rolling process, the product range for thin and ultra-thin products has been further enlarged, allowing for the production of hot rolled coils with a thickness of 0.8 mm for low carbon steel grades. Also high-strength steel grades may be produced with gauges below the minimum product thickness that can be achieved in a conventional-type hot rolling mill. Another step in the further development of CSP® technology is digitalization. In December 2016, the CSP® plant of Big River Steel (BRS), located in Arkansas, USA was put into operation. It is the first learning steel mill in the world. The CSP® plant of BRS comes with innovative technologies, providing impressive operational results right from the beginning.

Oct 1, 2019

By Francisco Morganti

The market requirements which strip processing lines have to deal with have altered significantly within the last decades. Particularly, the production has to be economical and ecological efficient and processing lines have to cover a broad product portfolio. Already existing plants either directly or indirectly are competing with new plants, which are equipped with the latest technologies. The “Special Strip Processing Equipment” is designed to be integrated easily and within small downtime phases in existing lines. All single machines can be delivered in short time “ready-to-perform” with a tested and proved automation system. Thus, the competitiveness of existing lines can be increased immediately with less effort. To find out which machines can be reasonably implemented SMS group offers an “Efficiency Check”. A special proceeding is used by experts to find out quickly which machines will have the largest effect on the efficiency of the line while demanding at the same time the smallest expense.

Aug 17, 2017

By Nigel Marx

In order to understand (and ultimately to predict) the friction reduction resulting from the use of polymer solutions, the rheological properties of model polymer solutions have been measured over a wide range of shear rates. Both temporary and permanent shear thinning have been observed. By using base fluids of different viscosities it has been shown that permanent shear thinning depends more closely on the shear stress experienced by the fluid than on the strain rate. Hydrodynamic measurements have been made on the polymer solutions using a compliant ball on flat lubricated contact that operates in isoviscous-elastic conditions. The measured friction values can only be predicted with reasonable accuracy if the measured shear thinning properties of the lubricant are taken into account in the hydrodynamic model.

Jul 31, 2018