Search Documents

By Harrison Souder

In view of the proposed visit of the Institute to Cuba this winter, the following brief sketch of the principal mineral deposits near Santiago de Cuba has been prepared largely from notes taken in February, 1903, during a visit to the mines then in operation in the province of Santiago de Cuba. Westward from Cape Maysi, the most eastern point of the island, the coast is rocky and uninviting. The usual course of the steamers is well in toward the shore, and the lines of stratification of the rocks can be distinguished clearly, the presence of iron or other ores being indicated by frequent blotches of mineral stain. One is impressed with the general rugged character of the southeastern coast-line,—an almost unbroken barrier of coral-limestone bluff's, full of caves and hollows, into which the surf rushes with a roar and bursts into tall fountains of spray. Beyond rises abruptly the Sierra Maestra range, whose sharp, peaked crest-line betrays its eruptive or igneous origin. From a height of about 800 ft. near Cape Maysi, this range gradually rises to the westward, attaining its maximum elevation of more than 8,300 ft. in the Pico Turquino, beyond Santiago. A general resemblance to the mountain-ranges of southern New Mexico is noticeable. At Daiquiri, 20 miles east of Santiago harbor, the extensive

Jan 1, 1905

By H. O. Hoffman, C. D. Demond

There are two methods of determining the fusibility or refractoriness of fire-clays, the theoretical and the experimental. In the former, conclusions are drawn from the chemical composition; in the latter, from the changes which the clay undergoes when subjeoted to intense heat. It is well to use both methods, beginning with the actual heat-test and explaining the results obtained from this by the help of the chemical analysis. In discussing the subject, however, it is better to reverse this order. I. The Theoretical Method.* Leaving out the hygroscopic and combined waters and any organic matter, as not directly affecting the fire-resisting property, the refractory constituents of fire-clay are alumina and silica, and the fluxing constituents magnesia, lime, soda, potash and ferric oxide. According to Bischof,† alumina is the least fusible component, and silica follows close upon it. If, however, a mixture of the two be heated, it will be found that its melting-point is much lower than that of alumina, as a silicate will then have been formed. The way in which silica affects the refractoriness of alumina has been strikingly presented by Seger 1 in a diagram reproduced in Fig. 1. The abscissæ represent the melting-points of Seger cones Nos. 26 to 36 (see p. 55); the ordinates, the relative amounts of alumina and

Jan 1, 1895

By J. T. Norton

As cold working is an important feature in a great many of the fabricating processes now applied, this paper presents some ideas of the nature and results of the plastic deformation produced in this operation. The art of manufacturing metal for practical uses is very old and has undergone very great development. The science of metals has also developed very rapidly recently and the various processes to which ,metals are submitted are much better understood now than they were even a short time ago. All the knowledge that can be obtained on this subject is useful because it promotes efficiency in converting metal into finished articles. ATOMIC ARRANGEMENT IN CRYSTALS In the solid state all metals are crystalline. The atoms are arranged in, a definite symmetrical configuration, which is repeated at regular intervals, and thereby defines what we may term a lattice. Presumably . the atoms exist as positive ions. The dissociated electrons place themselves between groups of positive ions, and thus define a second lattice, an "electron lattice." From such a point of view, the crystalline forces which hold a metal together are the electrostatic attractions between positive ions and negative electrons. The particular type of lattice into which a metal crystallizes depends on the number of these lattice electrons given up by each atom, and is thus connected very closely with the chemical valence of the metal.

Jan 12, 1926

By Bradley Stoughton

As a part of the systematic study of the alloys of iron under the auspices of the Engineering Foundation, and preliminary to the commencement of comprehensive work on this larger subject, the authors have undertaken an investigation of the available literature dealing: with the alloys of iron and silicon. The purpose is to collect all the data in English and foreign languages and present them in two mono-graphs, one of a more scientific and the second of a more industrially useful nature. Of course, a great deal of information upon the constitution of the iron-silicon alloys was found specificially upon the changes of phase in the equilibrium diagram and the different phases present, such as solid solution, chemical compounds (iron silicides), etc. While no extended research was contemplated in the particular study undertaken, nevertheless the data collected proved to be so contradictory in many respects that a simple study of some of the outstanding problems involved in the constitution and equilibrium diagram was undertaken Because research was not a primary object of the work, and also because of the extreme industrial importance of the silicon alloys between 0.80 and 14 per cent. silicon, and finally because of the unsatisfactory state of knowledge existing as to these alloys, the experimental investigation was limited entirely to alloys with less than 10 per cent. silicon.

Jan 1, 1930

By L. W. McKeehan, W. C. Elmore

THE magnetic powder method, long used for roughly mapping magnetic fields, has recently been refined 1,2 for investigating the microscopic variations in the surface magnetization of ferromagnetic crystals. Bitter' first discovered regular powder patterns connected with the crystal structure of such specimens. Several other investigators3 have used Bitter's original technique, with slight modifications, to study the variation of the patterns with variations in the magnetizing field applied parallel to the surface, and their dependence upon the state of strain, of polish and of crystal cut. All of the explanations of these patterns on metallic ferromagnetics have been couched in general terms. In a preliminary report we have described an improvement in the powder technique which led us to the discovery of a new effect throwing considerable light on the magnetic secondary structure of alpha iron4 and of nickel' single crystals. We now report additional evidence confirming the existence and stability of a magnetic block secondary structure. SPECIMENS The following list describes the specimens used in the present investigation. DESIGNATION DESCRIPTION A1 Silicon ferrite furnished to us by Dr. W. E. Ruder, of the General Electric Co., for which he gave the following typical analysis: C, 0.05; P, 0.038; 5, 0.026; Mn, 0.15; Si, 3.24. Disk, 0.60 cm. diameter, about 0.05 cm. thick.

Jan 1, 1935

By Charles E. Lundin

Pressure-temperature-composition data were obtainedfor the Er-H system. Measurements werecar-ried out in the temperature range of 473° to 1223°K, the composition range of erbium to ErH,, and the pressure range of 10-5 to 760 Torr. Solubility relationships were established from these data throughout the system. Three solid-solution phases were delineated: metal solid solution, dihydride phase, and trihydride phase. The trihydride Phase decomposes at about 656°K and 1 atm pressure. The dihydride phase is stable to about 1023°K, but becomes more deficient in hydrogen above this temperature. The equilibrium decomposition pressure-temperature relationships in the two-phase regions, erbium solid solution plus dihydride and dihydride plus trihydride, were deter- The differential heats of reaction in these two regions are AH = - 52.6 * 0.3 and - 19.8 i 0.2 kcal per mole of Hz, respectively. The differential entropies of reaction are AS = - 35.2 * 0.3 and - 30.1 * 0.4 cal per mole HZ.deg, respectively. Relative partial molal and integral thermodynamic quuntities were calculated in the system to the dihydride phase. RARE earth metal-hydrogen systems have been the subject of general survey,1"4 and all have been found to form hydride phases. The heavy rare earths, of which erbium is a member, form dihydride and trihydride phases with different crystal structures, whereas the light rare earths form only a single-phase dihydride which expands without structure change, as hydrogen is added, to the trihydride composition. These materials are of interest primarily because of their theoretical properties, such as bonding, defect structure, and thermodynamic and electronic characteristics. Erbium has been studied in several previous investigations.5, 6 It was deemed desirable to more thoroughly and accurately define the system, both for the phase equilibria and the thermodynamic properties. I) EXPERIMENTAL PROCEDURE A Sieverts&apos; apparatus was employed to conduct the experimental measurements. Briefly, it consisted of a source of pure hydrogen, a precision gas-measuring buret, a heated reaction chamber, a mercury manometer, and two McLeod gages (a CVC, GM 100A and CVC, GM 110). Pure hydrogen was obtained by passing hydrogen through a heated Pd-Ag thimble. The hydrogen was analyzed and found to have only a trace of oxygen and nitrogen. A 100-ml precision gas buret graduated to 0.1-ml divisions was used to measure and admit hydrogen to the reaction chamber. The reaction unit consisted of a quartz tube surrounded by a nichrome-wound furnace. The furnace temperature was controlled by a recorder-controller to ±1°K. An independent measurement of the sample temperature in the quartz tube was made by means of a chromel-alumel thermocouple situated outside, but adjacent to, the quartz tube near the specimen. Pressure in the manometer range was measured to ±0.5 Torr and in the McLeod range (10-4 to 10 Torr) to ±3 pct. The hydrogen compositions in erbium were calculated in terms of hydrogen-to-erbium atomic ratio. These compositions were estimated to be ±0.01 H/Er. The erbium metal was obtained from the Lunex Co. in the form of sponge. The metal was nuclear grade with a purity of 99.9 pct +. The oxygen content was reported to be 340 ppm and the nitrogen not detectable. Metallographically the structure was almost free of second phase (<1 vol pct). A quantity of sponge was arc-melted for use as charge material. The solid material was compared with the sponge in the pressure-temperature-composition relationships. They were found to be identical. Therefore, sponge material was used henceforth, so that equilibrium could be attained more rapidly. The specimen size was about 0.2 grain for each loading of the reaction chamber. The procedure employed to obtain the pressure-temperature-composition data was to develop experimentally a family of isothermal curves of composition vs pressure. First, a specimen of erbium was wrapped in a tungsten foil capsule to prevent contact with the quartz tube. After loading the specimen, the system was evacuated to less than l0-6 Torr, flushed several times with high-purity hydrogen, and evacuated again ready for the start of the experiment. The furnace was then brought to the desired temperature. A measured amount of hydrogen was admitted into the chamber. Equilibrium was allowed to be attained, the pressure read, and the process then repeated many times until 1 atm of gas pressure was finally reached. Other isotherms were then developed in the same manner. The partial pressure plateaus were determined by another manner. In the solid solution-dihydride region a composition of approximately 1.0 H/Er was selected on the plateau. The temperature was varied throughout the range of interest. At each temperature level, equilibrium was achieved, the pressure read, and the next temperature attained. The temperature was cycled both up and down. In the dihydride-trihy-dride region, the plateaus were determined in the 473" to 651°K range only by heating to the desired temperature and not by both heating and cooling. The data were much more reproducible in this manner. Equilibrium required long periods of time. Specimens were initially hydrided to 2.8 H/Er, so that at the higher

Jan 1, 1969

By K. M. Myles

The vapor pressure of palladium over a series of Rlz-Pd alloys has been measured by the torsion-effusion method. The thermodynamic properties of the alloy system at 1575=K have been calculated from the vapor pressure data. The activities and the free energies of formation exhibit large positive deviations from ideal behavior. The enthalpies of formation are endother-mic. The entropies of formation are positive and larger than the ideal entropy of mixing. All of the thermodynamic properties suggest that a strong tendency toward phase separation exists in the solid solutions. The possible origin of the phase instability and the various factors that influence the thermodynamic properties are discussed. RECENT studies of the thermodynamic properties of alloys of palladium with nontransition elements have indicated that a significant contribution to the enthalpy of formation is related to the redistribution of the conduction electrons upon alloy formation.&apos;-&apos; The present work was undertaken to ascertain the importance of this contribution in Pd/transition-metal alloys. The Rh-Pd system was chosen for this investigation for several reasons: 1) The thermodynamics of the system were unknown. 2) Rhodium and palladium are completely soluble at high temperatures; below 1118OK the solid solution becomes immiscible.&apos;, 3) The difference in magnitude between the vapor pressures of rhodium and palladium permitted the use of an existing effusion apparatus. 4) Additional information was known about the alloy system that would facilitate the interpretation of the thermodynamic results. EXPERIMENTAL PROCEDURE The thermodynamic properties of the Rh-Pd alloy system were calculated from the vapor pressure of palladium over solid palladium and over several solid Rh-Pd alloys. The vapor pressure was measured by means of the torsion-effusion apparatus that has been described previously. In this method, an effusion cell is suspended from a tungsten filament inside a high-temperature furnace. Two orifices are located eccentrically such that the effusion of the vapor creates a rotational torque in the filament. The angle of rotation is directly related to the total vapor pressure within the cell. As the vapor pressures of rhodium and palladium are approximately five orders of magnitude apart," the total vapor pressure was considered to be effectively equal to the equilibrium vapor pressure of palladium. The effusion cells were made from high-purity alumina since auxiliary experiments indicated that essentially no reaction occurs between alumina and solid Rh-Pd alloys. Unfortunately, because the orifices were irregular, an accurate calculation of the Free- man-Searcy correction factors" could not be made. The constants were determined in an independent experiment where the vapor pressure of copper, as measured in the alumina cell, was compared with an accurate value of the vapor pressure, which had been determined previously.4 Depletion of palladium from the surfaces of the specimens was minimal as the deflection of the cell remained constant, for at least 15 minutes, at each of the experimental temperatures. Lattice parameter measurements of the postrun alloys also indicated that no changes in the composition of the surfaces had occurred. The alloys were prepared by arc melting the requisite amounts of the 99.99 pct pure elements. The four most palladium-rich alloys were remelted in a levita-tion furnace since complete melting of the components had not occurred in the arc furnace. All of the alloys were subsequently homogenized at elevated temperatures in sealed alumina thimbles. After heat treatment, the alloys were analyzed chemically and were in essential agreement with the nominal compositions. The thermal histories and nominal compositions of the alloys are given in Table I. Lattice parameters of the heat-treated alloys were computed, by means of the method described by Mueller et a1. ,I2 from X-ray diffraction powder patterns obtained with filtered copper radiation in a 114.6-mm-diam Straumanis-type Debye-Scherrer camera. The results, which are tabulated in Table I, exhibit a slightly greater negative deviation from Vegards&apos; law than the values reported by Raub et al.13 The diffraction lines were sharp and well-resolved and thus indicated that the alloys were homogenous. RESULTS The logarithms of the individual values of the vapor pressure of palladium were fit, by the least-squares method, as a linear function of the reciprocal of the absolute temperatures. The constants of the equations are given in Table I along with the temperature range over which the data was accumulated. The latent heat of vaporization at 298.15"K for pure palladium, calculated by the third-law method,14 showed no systematic temperature dependence. The average value of 88,920 * 20 cal per g-atom agrees favorably with the average of the results obtained in the most reliable previous investigations.15"19 The activities of palladium were computed from the vapor pressure data at 1525&apos;, 1575", and 1625OK. Consistent with the mass spectrometric study of the atomicity of palladium vapor,lg the vapor was assumed to be monoatomic. The activities of rhodium were determined by integrating the Gibbs-Duhem equation with the aid of the a function.20 In the calculations, the activities of the pure solid metals were assigned the value of unity. From the activities, the partial and integral free energies, entropies, and enthalpies of formation at 1575° K were computed; they are assembled in Table 11.

Jan 1, 1969

By C. E. Lesher

THIS paper reports a study of the reactivity of 950°F and 1650°F cokes as measured by relative rates of reduction of iron oxides at temperatures up to 2200°F. Previous work cited shows general acceptance of the theory that reduction by carbon is a gaseous reaction, and that kind and character of carbon as well as particle size have measurable effect on the velocity of reaction. As will be shown, the data obtained in this study confirm those conclusions. The work was not designed to examine iron oxide reduction equilibrium, but if reaction velocity be defined as the speed with which "a reaction tends to approach conditions of equilibrium," the data here presented may be considered as a study of reaction rates, and the relative degree of reduction to metallic iron as the measure of reactivity. Three standardized combinations of Lake Superior brown iron ore with carbon were tested by similar procedures. One combination was a mechanical mixture of carefully sized high-temperature coke (1650°F) with the ore. The second was a mechanical mixture of the ore with Disco* obtained by carbonizing the identical coal at 950 °F. The third was an agglomerate prepared by carbonizing the coal and ore at 950°F, premixed in proportions to give as nearly as possible the same relative amounts of carbon and ore as the mechanical mixtures. This agglomerate, obtained by heating the finely divided ore (through 30 mesh) with coking coal through the plastic temperature range so as to form solid aggregates, gives a product in which the oxide particles are impregnated with, and intimately bound together with low-temperature coke. The agglomerate-—ore-Disco—was most active in oxide reduction; the mechanical mixtures of Disco and ore next in order, with coke the least reactive. General Discussion: Carbon exists in many forms and it is well known that the form or nature of the carbon used in reduction of oxides is related to the critical temperature of reduction. Sugar carbon, charcoal, and lampblack are forms of carbon that will reduce oxides at lower temperatures than high-temperature coke, and coke will, in turn, give a lower critical reduction temperature than graphite. There have been many investigations of this characteristic of carbons. Johnson&apos; reported a difference of 130°F (70°C) in the critical reduction temperature of zinc oxide as between charcoal 1891 °F (1033°C) and Acheson graphite turnings 2021°F (1105°C) with zinc oxide. Bodenstein2 using charcoal and coke, found a difference of 138°F (77°C) comparing an experimental figure of 2066°F (1130°C) for coke and 1928°F (1053°C) for charcoal, in the reduction of zinc oxide. He concluded that this is very marked and observed that the "type of carbon merely raises or lowers the temperature at which rapid reaction takes place." Comparing the effectiveness of types of carbon in reduction of zinc oxide, it was found that a "brown coal coke" gave 97 pct zinc elimination at 1832°F (1000°C), as compared with 48 pct with "hard coal coke."&apos; A wide range of metallic oxides was studied by Tammann and Sworykin,4 who found that the temperature at which decomposition of oxides begins depends on the nature of the carbon used. Carbon in the form of graphite, lampblack, and sugar carbon was investigated. Sugar charcoal will reduce Fe2O3 to Fe3O4 at 842°F (450°C) as compared with 1112°F (600°C) for coke, according to Meyer." Direct reduction of iron oxides by charcoal begins at 1382°F (750°C), but "first becomes intense" at 1652°F (900°C), whereas with coke, direct reduction begins at 1742°F (950°C), and "first becomes appreciable" at 2012°F (1100°C).6 he total reduction of the sample under certain conditions when heated in a current of CO with charcoal was about 100 pct for limonite and about 77 pct for magnetite. Using coke under the same conditions, the respective percentages were 75 and 47. In a study of processes for sponge iron7 by the Bureau of Mines, the conclusion was reached that a low-temperature char from noncoking subbituminous coal is the most satisfactory solid reducing agent. In a critical study of zinc smelting from a theoretical viewpoint Maier8 concluded that the reduction is by CO, that the reaction between ZnO and CO is intrinsically more rapid than the subsequent reduction of CO2 by C, which is limited by diffusion rates, which in part effectively limits the smelting process. Maier said that the operation is improved with the activity of the reducing carbon. An active carbon, he said, is one maintaining a low CO, content in the retort. Reactivity of Carbon: One form of carbon is more potent in reducing oxides than another. A carbon that reacts faster than another at a given temperature is said to be more reactive. Reactivity is measured by several methods, using carbon dioxide, air, or steam as reactants.9 ebastian and Mayers" have developed a method for the determination of absolute reaction rates between coke and oxygen by a study of ignition points under certain conditions. These and other investigators have established the relative reactivity of types of carbon. Lignite, charcoal, bituminous coal, cokes in the ascending order

Jan 1, 1951

By R. L. Dietrich

Magnesium alloy sheet has less ability to accept bending at room temperature than most of the heavier metals. In work designed to improve the bend properties, the preferred orientation of the sheet is of major importance as it is in all studies of the properties of wrought magnesium products. When rolled into sheet, all of the common magnesium alloys form an orientation texture having the basal (002) planes approaching parallel to the surface of the sheet. This texture is only slightly affected by annealing. Magnesium single crystals are highly anisotropic, and, as might be expected, so are magnesium alloy wrought products in which a strong preferred orientation is developed. It is therefore not surprising that bend properties are affected by orientation. Ansel and Betterton1 reported that the orientation of AZ3lXt sheet varies from surface to center and that bend properties are improved by etching away the sharply oriented material at the surface of the sheet to reach the more broadly oriented structure below. This paper covers a study of that orientation, either during the rolling process or by treatment of the finished sheet, in an effort to improve the bend properties and toughness of sheet. Literature The orientation texture of magnesium and magnesium alloy sheet has been studied extensively. Early determinations2 showed that pure magnesium sheet has a preferred orientation in which the basal planes are parallel to the sheet surface within very narrow limits. J. C. hIcDonald3 and J. D. Hanawalt4 reported that sheet containing a small amount of calcium develops a "double" texture, that is, the majority of the basal planes are a few degrees from parallel to the surface and there is a noticeable vacancy at the parallel position. Bakarian5 made careful quantitative pole figures of both pure magnesium sheet and MI alloy SEPTEMBER 1949 sheet which show these features. In all of these studies, however, the orientation was determined by transmission methods in which the resulting pattern is an average through the thickness of the sheet. The tendency of wrought metal to exhibit a different orientation at the surface from that in the center has been reported by many investigators. G. von Vargha and G. Wasserman6 found that with copper, aluminum, iron, and brass the textures of rolled compared to drawn wires were the same at the center but differed markedly at the surface. It was also reported by investigators7 that the orientation of rolled aluminum varies from surface to center. Har-greaves8 found that the surface texture of AM503 (magnesium alloy similar to MI) sheet was different from the center texture. It is reported by Edmunds and Fuller9 that zinc alloy sheet sometimes had a thin layer at the surface with a strong orientation of the basal planes parallel to the surface, which, if present, impaired the bend properties of the sheet. Part1 Surface Orientation ofMag- nesium Alloy Sheet and the Effect on Properties Attempts to correlate the bend properties of magnesium alloy sheet with tension ductility over short gauge lengths proved unsuccessful and the subsequent investigation showed that nonuniformity in orientation is a con- tributing factor as the properties of the surface material have a much more important effect in bending than in tension. A program to study the relationship between surface orientation at the surface and bend properties was then undertaken. First, the effect of etching away the surface of sheet on the bend properties and the orientations at the various depths were studied. Sheet samples of M1, AZ31X, and AZ61X were etched in dilute nitric acid to remove the surface material for various depths to 0.015 in. As may be seen in Table 1, the minimum bend radius improved considerably as the surface layers were etched away but it was necessary to etch the sheet quite deeply, much more so than was found necessary by Edmunds and Fuller9 on zinc sheet. It is also apparent that the amount of etching required is a function of the sheet thickness. In all of this work, radii were measured as R/t, the radius divided by the sheet thickness, in order to eliminate the effect of the reduction in sheet thickness produced by the etching. To determine the orientation texture of the sheet, X ray reflection patterns were taken using copper radiation with the bearn striking the specimen at an angle of 17&apos; to the surface, which is the Bragg angle for the (002) planes of magnesium. Two exposures were made of each specimen, one with the beam perpendicular to the rolling direction and the other with the beam parallel to the rolling direction. The symmetry of the preferred orientation in magnesium sheet is such that these two photographs gave an approximation of the pole figure sufficiently accurate for qualitative work and it was not thought worthwhile to make complete pole figures. These X ray patterns show that the orientation has a much narrower spread at the original surface of the sheet than below the surface. The narrow spread is found in sheet having the majority of the basal planes (002) parallel to the surface, and since this is an unfavorable position for slip, it is

Jan 1, 1950

By C. E. Lesher

THIS paper reports a study of the reactivity of 950°F and 1650°F cokes as measured by relative rates of reduction of iron oxides at temperatures up to 2200°F. Previous work cited shows general acceptance of the theory that reduction by carbon is a gaseous reaction, and that kind and character of carbon as well as particle size have measurable effect on the velocity of reaction. As will be shown, the data obtained in this study confirm those conclusions. The work was not designed to examine iron oxide reduction equilibrium, but if reaction velocity be defined as the speed with which "a reaction tends to approach conditions of equilibrium," the data here presented may be considered as a study of reaction rates, and the relative degree of reduction to metallic iron as the measure of reactivity. Three standardized combinations of Lake Superior brown iron ore with carbon were tested by similar procedures. One combination was a mechanical mixture of carefully sized high-temperature coke (1650°F) with the ore. The second was a mechanical mixture of the ore with Disco* obtained by carbonizing the identical coal at 950 °F. The third was an agglomerate prepared by carbonizing the coal and ore at 950°F, premixed in proportions to give as nearly as possible the same relative amounts of carbon and ore as the mechanical mixtures. This agglomerate, obtained by heating the finely divided ore (through 30 mesh) with coking coal through the plastic temperature range so as to form solid aggregates, gives a product in which the oxide particles are impregnated with, and intimately bound together with low-temperature coke. The agglomerate-—ore-Disco—was most active in oxide reduction; the mechanical mixtures of Disco and ore next in order, with coke the least reactive. General Discussion: Carbon exists in many forms and it is well known that the form or nature of the carbon used in reduction of oxides is related to the critical temperature of reduction. Sugar carbon, charcoal, and lampblack are forms of carbon that will reduce oxides at lower temperatures than high-temperature coke, and coke will, in turn, give a lower critical reduction temperature than graphite. There have been many investigations of this characteristic of carbons. Johnson&apos; reported a difference of 130°F (70°C) in the critical reduction temperature of zinc oxide as between charcoal 1891 °F (1033°C) and Acheson graphite turnings 2021°F (1105°C) with zinc oxide. Bodenstein2 using charcoal and coke, found a difference of 138°F (77°C) comparing an experimental figure of 2066°F (1130°C) for coke and 1928°F (1053°C) for charcoal, in the reduction of zinc oxide. He concluded that this is very marked and observed that the "type of carbon merely raises or lowers the temperature at which rapid reaction takes place." Comparing the effectiveness of types of carbon in reduction of zinc oxide, it was found that a "brown coal coke" gave 97 pct zinc elimination at 1832°F (1000°C), as compared with 48 pct with "hard coal coke."&apos; A wide range of metallic oxides was studied by Tammann and Sworykin,4 who found that the temperature at which decomposition of oxides begins depends on the nature of the carbon used. Carbon in the form of graphite, lampblack, and sugar carbon was investigated. Sugar charcoal will reduce Fe2O3 to Fe3O4 at 842°F (450°C) as compared with 1112°F (600°C) for coke, according to Meyer." Direct reduction of iron oxides by charcoal begins at 1382°F (750°C), but "first becomes intense" at 1652°F (900°C), whereas with coke, direct reduction begins at 1742°F (950°C), and "first becomes appreciable" at 2012°F (1100°C).6 he total reduction of the sample under certain conditions when heated in a current of CO with charcoal was about 100 pct for limonite and about 77 pct for magnetite. Using coke under the same conditions, the respective percentages were 75 and 47. In a study of processes for sponge iron7 by the Bureau of Mines, the conclusion was reached that a low-temperature char from noncoking subbituminous coal is the most satisfactory solid reducing agent. In a critical study of zinc smelting from a theoretical viewpoint Maier8 concluded that the reduction is by CO, that the reaction between ZnO and CO is intrinsically more rapid than the subsequent reduction of CO2 by C, which is limited by diffusion rates, which in part effectively limits the smelting process. Maier said that the operation is improved with the activity of the reducing carbon. An active carbon, he said, is one maintaining a low CO, content in the retort. Reactivity of Carbon: One form of carbon is more potent in reducing oxides than another. A carbon that reacts faster than another at a given temperature is said to be more reactive. Reactivity is measured by several methods, using carbon dioxide, air, or steam as reactants.9 ebastian and Mayers" have developed a method for the determination of absolute reaction rates between coke and oxygen by a study of ignition points under certain conditions. These and other investigators have established the relative reactivity of types of carbon. Lignite, charcoal, bituminous coal, cokes in the ascending order

Jan 1, 1951

By W. N. Poundstone, P. C. Thakur

Introduction Horizontal drilling in coal mines is a relatively new technology. The earliest recorded drilling in the United States was done in 1958 at the Humphrey mine of Consolidation Coal Co. for degasification of coal seams. Spindler and Poundstone experimented with vertical and horizontal holes for several years. They concluded in 1960 that horizontal drilling in advance of underground mining appeared to offer the most promising prospect (for degasification) but effective and extensive application would be dependent upon the ability to drill long holes, possibly 300 to 600 m, with reasonably precise directional control and within practical cost limits (Spindler and Poundstone, 1960). Mining Research Division of Conoco Inc., the parent company of Consolidation Coal Co., began a research program in the early 1970s to achieve the above objective. The technology needed to drill nearly 300 m in advance of working faces was developed by 1975 and experiments on advance degasification with such deep holes began in 1976. Preliminary results of this research have already been published (Thakur and Davis, 1977). To date nearly 4.5 km of horizontal holes have been drilled for advance degasification and earlier results were reconfirmed. In summary, these are: • The greatest impact of these boreholes was felt in the face area where methane concentrations were reduced to nearly 0.3% in course of two to three months from original values of nearly 0.95%. • The methane concentration in the section return reduced to 50% of its original value immediately after the boreholes were completed, indicating a capture ratio of 50%. • The total methane emission in the section (rib and face emission plus the borehole production) did not increase but rather gradually declined with time. • Initial production from 300 m deep boreholes in the Pittsburgh seam varied from 3 m3/min to 6 m3/min but then slowly declined as workings advanced inby of the drill site (well head) exposing a larger surface area parallel to the borehole. Encouraged by these results, it was decided to design a horizontal drilling system that would be mobile and compatible with other face equipment. A mobile horizontal drill can be divided into three subsystems: the drill rig, the drill bit guidance system, and borehole surveying instruments. The drill rig provides the thrust and torque necessary to drill 75- to 100-mm diam holes up to 600 m deep and contains the mud circulation and gas cuttings separation systems. The drill bit guidance system guides the bit up, down, left, or right as desired. Borehole surveying instruments measure the pitch, roll, and azimuth of the borehole assembly. Additionally, it also indicates the thickness of coal between the borehole and the roof or floor of the coal seam. Thus, it becomes a powerful tool for locating the presence of faults, clay veins, sand channels, and the thickness of coal seam in advance of mining. In recent years, many other potential uses of horizontal boreholes have come to light, such as in situ gasification, longwall blasting, improved auger mining, and oil and gas production from shallow deposits. The purpose of this paper is to describe the hardware and procedure for drilling deep horizontal holes. The Drilling Rig [Figures 1 and 2] show the two components of the mobile drilling rig: the drill unit and the auxiliary unit. The equipment (except for the chassis) was designed by Conoco Inc. and fabricated by J. H. Fletcher and Co. of Huntington, WV. The drill unit. It is mounted on a four-wheel drive chassis driven by two Staffa hydraulic motors with chains. The tires are 369 X 457 mm in size and provide a ground clearance of 305 mm. The prime mover is a 30-kw explosion-proof electric motor which is used only for tramming. Once the unit is Crammed to the drill site, electric power is disconnected and hydraulic power from the auxiliary unit is turned on. Four floor jacks are used to level the machine and raise the drill head to the desired level. Two 5-t telescopic hydraulic props, one on each side, anchor the drill unit to the roof. The drill unit houses the feed carriage, the drilling console, 300 m of 3-m-long NQ, drill rods, and the electric cable reel for instruments. The feed carriage is mounted more or less centrally, has a feed of 3.3 m, and can swing laterally by ± 17°. It can also sump forward by 1.2 m. The drill head has a "through" chuck such that drill pipes can be fed from the side or back end. General specifications of the feed carriage are: [ ] The auxiliary unit. The chassis for the auxiliary unit is identical to the drill unit but the prime movers are two 30-kW explosion proof electric motors. It is equipped with a methane detector- activated switch so that power will be cut off at a preset methane concentration in the air. No anchoring props are needed for this unit. The auxiliary unit houses the hydraulic power pack, the water (mud) circulating pump, control boxes for electric motors, a trailing cable spool, and a steel tank which serves for water storage and closed-loop separation of drill cuttings and gas.

Jan 1, 1981

By A. Y. Bethune, W. G. Woolf

THE hydrometallurgy of special high-grade zinc as practiced by the Sullivan Mining Co. at its electrolytic zinc plant, Kellogg, Idaho, involves an important filtration step immediately following the leaching process. By means of the filtration the heavy zinc sulphate solution is separated from the residual products which remain after the zinc calcine has been dissolved in the sulphuric acid electrolyte. Because this plant uses the so-called high-acid, high-density process&apos; for the production of First, the strength of the electrolyte (270g H,SO, per liter) results in a saturated zinc sulphate solution, having a specific gravity of 1.510 to 1.540, which must be kept warm during filtration because of its property of "seeding out" small crystals if allowed to drop much below 60°C. Second, the action of the "high" acid on zinc calcine under the temperature conditions of the leach (80" to 102 "C), although favorable to good zinc extraction, causes a considerable quantity of iron to be dissolved (8 to 18. g per liter) along with variable quantities of alumina and silica, depending on the grade and type of original zinc concentrates roasted. These three, iron, alumina, and silica, are almost completely precipitated during the neutralization of the leach (only a few. milligrams per liter of each remain in solution), so that the resulting pulp, instead of being a granular, sand-like product having a particle-size distribution dependent on the fineness of the zinc calcines leached, is in reality a slimy, chemical precipitate whose filtration characteristics constantly change depending on the amounts of iron silica, and other impurities, which are dissolved and reprecipi-tated. Third, the combination of supersaturated solution of high specific gravity plus a dense, semi-gelatinous residue creates a difficult washing problem requiring a positive displacement wash to liberate the zinc sulphate entrapped in the pulp. In a closed-cycle hydrometallurgical operation, such as practiced in this plant, the extent of washing is determined by the volum,e limitations imposed on the intermediate wash waters by the amount of "fresh" (or process) water which may be added. The volume of fresh water used for makeup purposes is limited to the amount which is lost during the closed cycle by evaporation in the leach, sulphate content of the calcines leached, moisture content of the residue, and spillage. The Burt filter as modified and improved by the Sullivan Mining Co. has successfully met and overcome these difficulties under a variety of zinc plant operating conditions since 1928. It might have many interesting applications to metallurgical fields other than that of electrolytic zinc, and its possible usefulness to hydrometallurgists in general warrants its description and discussion. The Burt filter is so named from its inventor who originated it in Mexico for pulp filtration in the cyanide process for gold and silver ores. While retaining the basic principle of Burt&apos;s earlier revolving pressure-type filter with internal filtration media, a number of modifications and improvements have been made in Sullivan Mining Co.&apos;s installation. The Burt filter may be classified as a batch-type pressure filter in contradistinction to either the conventional vacuum-type filter, which depends on atmospheric pressure to force solution through a cloth medium, or to the filter-press, which employs whatever pressure is imparted by the pump delivering the liquid being filtered. The Burt consists essentially of a hollow steel cylinder about 40 ft long, 5 ft in diameter, resting horizontally, and capable of rotation about its long axis. It is supported on one end by a hollow trunnion and near the other end by a riding-ring and roller combination. The cylinder is lined with filter units each fastened against the inside of the shell and parallel to the long axis so as to form a hollow cavity into which pulp may be charged. A specific amount of pulp is admitted to the filter and a unique valving arrangement prevents the loss of pulp while air pressure forces the solution through a canvas medium to the discharge port of each filter unit. The residue is left on the surface of the canvas inside the cavity. The remainder of the filter cycle is concerned with washing the residue free of zinc sulphate, discharging it from the Burt, and preparing the filter for the next charge. A more detailed description of Burt filter construction, a typical filter cycle, and its operating characteristics when employed on material encountered in this plant will be given in that order. Description of the Filter: Fig. 1 shows a side elevation view of a filter with riveted shell construction. Since this drawing was made shells have been fabricated by welding, instead of riveting, with complete success. Shells are lagged on the outside to retain heat. Fig. 1 shows a side elevation and plan view of a Burt filter in operating position. The 1/2-in. steel shells are lined with 3/16-in. copper sheet as protection against the corrosive action of the solution (containing about 500 mg Cu per liter) on iron, and the copper is given a thin protective coating of plastic-base paint. Fig. 2 is a view from the discharge end of the filter, with head removed, before filter units are fastened to the periphery. It shows

Jan 1, 1951

By W. G. Woolf, A. Y. Bethune

THE hydrometallurgy of special high-grade zinc as practiced by the Sullivan Mining Co. at its electrolytic zinc plant, Kellogg, Idaho, involves an important filtration step immediately following the leaching process. By means of the filtration the heavy zinc sulphate solution is separated from the residual products which remain after the zinc calcine has been dissolved in the sulphuric acid electrolyte. Because this plant uses the so-called high-acid, high-density process&apos; for the production of First, the strength of the electrolyte (270g H,SO, per liter) results in a saturated zinc sulphate solution, having a specific gravity of 1.510 to 1.540, which must be kept warm during filtration because of its property of "seeding out" small crystals if allowed to drop much below 60°C. Second, the action of the "high" acid on zinc calcine under the temperature conditions of the leach (80" to 102 "C), although favorable to good zinc extraction, causes a considerable quantity of iron to be dissolved (8 to 18. g per liter) along with variable quantities of alumina and silica, depending on the grade and type of original zinc concentrates roasted. These three, iron, alumina, and silica, are almost completely precipitated during the neutralization of the leach (only a few. milligrams per liter of each remain in solution), so that the resulting pulp, instead of being a granular, sand-like product having a particle-size distribution dependent on the fineness of the zinc calcines leached, is in reality a slimy, chemical precipitate whose filtration characteristics constantly change depending on the amounts of iron silica, and other impurities, which are dissolved and reprecipi-tated. Third, the combination of supersaturated solution of high specific gravity plus a dense, semi-gelatinous residue creates a difficult washing problem requiring a positive displacement wash to liberate the zinc sulphate entrapped in the pulp. In a closed-cycle hydrometallurgical operation, such as practiced in this plant, the extent of washing is determined by the volum,e limitations imposed on the intermediate wash waters by the amount of "fresh" (or process) water which may be added. The volume of fresh water used for makeup purposes is limited to the amount which is lost during the closed cycle by evaporation in the leach, sulphate content of the calcines leached, moisture content of the residue, and spillage. The Burt filter as modified and improved by the Sullivan Mining Co. has successfully met and overcome these difficulties under a variety of zinc plant operating conditions since 1928. It might have many interesting applications to metallurgical fields other than that of electrolytic zinc, and its possible usefulness to hydrometallurgists in general warrants its description and discussion. The Burt filter is so named from its inventor who originated it in Mexico for pulp filtration in the cyanide process for gold and silver ores. While retaining the basic principle of Burt&apos;s earlier revolving pressure-type filter with internal filtration media, a number of modifications and improvements have been made in Sullivan Mining Co.&apos;s installation. The Burt filter may be classified as a batch-type pressure filter in contradistinction to either the conventional vacuum-type filter, which depends on atmospheric pressure to force solution through a cloth medium, or to the filter-press, which employs whatever pressure is imparted by the pump delivering the liquid being filtered. The Burt consists essentially of a hollow steel cylinder about 40 ft long, 5 ft in diameter, resting horizontally, and capable of rotation about its long axis. It is supported on one end by a hollow trunnion and near the other end by a riding-ring and roller combination. The cylinder is lined with filter units each fastened against the inside of the shell and parallel to the long axis so as to form a hollow cavity into which pulp may be charged. A specific amount of pulp is admitted to the filter and a unique valving arrangement prevents the loss of pulp while air pressure forces the solution through a canvas medium to the discharge port of each filter unit. The residue is left on the surface of the canvas inside the cavity. The remainder of the filter cycle is concerned with washing the residue free of zinc sulphate, discharging it from the Burt, and preparing the filter for the next charge. A more detailed description of Burt filter construction, a typical filter cycle, and its operating characteristics when employed on material encountered in this plant will be given in that order. Description of the Filter: Fig. 1 shows a side elevation view of a filter with riveted shell construction. Since this drawing was made shells have been fabricated by welding, instead of riveting, with complete success. Shells are lagged on the outside to retain heat. Fig. 1 shows a side elevation and plan view of a Burt filter in operating position. The 1/2-in. steel shells are lined with 3/16-in. copper sheet as protection against the corrosive action of the solution (containing about 500 mg Cu per liter) on iron, and the copper is given a thin protective coating of plastic-base paint. Fig. 2 is a view from the discharge end of the filter, with head removed, before filter units are fastened to the periphery. It shows

Jan 1, 1951

By E. A. Gulbransen, K. F. Andrew

The gas-metal reactions of zirconium are very interesting. The metal is extremely stable at room temperature to reactions with the several gases present in air and the metal will stay bright indefinitely. However, at temperatures of several hundred degrees higher the metal reacts readily with oxygen, nitrogen and hydrogen. This behavior, in addition to the fact that zirconium is one of the higher melting point metals which might have high temperature applications under the proper conditions, resulted in the work reported in this communication. There are several factors which indicate that zirconium might have good oxidation resistance at elevated temperatures. These are: (1) the high melting point of approximately 1860°C, (2) the high melting point of the oxide of approximately 2675°C, (3) the high degree of thermodynamic stability of the oxide to chemical reaction and the low decomposition pressure of the oxide and (4) the possible formation of a continuous oxide film since the volume ratio of oxide to metal is greater than unity. The unfavorable factors are: (1) the metal reacts to form nitrides, hydrides and carbides, (2) the oxide is soluble at elevated temperatures in the metal and (3) the oxide ZrO2 undergoes crystal structure transformations at high temperature. The oxidation resistance of this metal is not only a question of the rate of film formation but is complicated by the fact that the oxide and other reaction products dissolve in the metal which in turn will affect the physical and mechanical properties of the metal. The protection of the metal to nitride formation must be considered separately from the oxide problem. One unfavorable factor is that the volume ratio of the nitride to the metal is about unity. This indicates that a discontinuous film might be formed. This paper will present measurements on the rates of reaction of the metal with O2, H2 and N2 over a wide temperature and pressure range. The reaction in high vacuum and the stability of the several compounds formed will be presented. The results are correlated with fundamental rate theory and with the physical and chemical structure of the metal and film. Literature Although many papers have been published on the chemical reactions of zirconium with various gases, comparatively few are concerned with the protective nature of the metal and its reactions at normal pressures. The studies in the pressure range below 0.01 mm of Hg gas pressure are largely of interest in the nature of the adsorption of gases by hot filaments in high vacuum apparatus. The reactions of zirconium in this pressure range have been reviewed by Fast8 and by RaynOr.27 In spite of certain differences of opinion as to the maximum adsorption temperatures for various gases, the low pressure range is qualitatively understood. Some of these papers will be mentioned briefly here. 1. LOW PRESSURE Ehrke and Slack&apos; find that oxygen reacts above 885°C and hydrogen above 760°C. Nitrogen does not react up to a temperature of 1527°C. Fast9 on the other hand observes that oxygen is absorbed above 700°C and nitrogen at temperatures exceeding 1000°C. Hydrogen is absorbed from 300" to 400°C and liberated between 500" and 800°C. It is readsorbed at 862°C and released above 862°C. Hukagawa and Nambo22 find a rather complicated picture for the absorption of oxygen. A rapid initial absorption is found between 180" to 230°C. Further oxygen is not taken up until a temperature of 450°C is reached. The optimum temperature for complete absorption is 650" to 700°C. Nitrogen is found to be completely adsorbed at 600°C. However some of the gas is evolved at higher temperatures. Their data on the absorption of hydrogen indicate some of the gas is removed at 550°C. Guldner and Wooten17 in a study of the low pressure reactions of zirconium with various gases observed that the reaction with oxygen occurs at temperatures above 400°C and that the oxide is formed. The reactions with carbon monoxide and carbon dioxide occur rapidly at temperatures of about 800°C with the oxide and carbide being formed. Zirconium reacts at temperatures of 400°C slowly and at 800°C rapidly to form the nitride and with hydrogen and water at 300°C to form the hydride and a mixture of the oxide and hydride respectively. 2. NORMAL PRESSURE DeBoer and Fast3 in a study of the electrolysis of oxygen in zirconium find that the metal absorbs up to 40 at. pct of oxygen without forming a new phase. The solubility of nitrogen in the lattice has been studied by de Boer and Fast4 and Fast10 and is found to be considerable. At higher temperatures the oxide dissolves in the lattice at an appreciable rate according to Fast10 and the zirconium surface becomes active. De Boer and Fast4 and Hägg18 have studied the solubility of hydrogen and find that at room temperature the solubility corresponds to ZrH1.95 Desorption occurs on lowering the pressure. Hydrogen is stated to be more soluble in the ß-form and the

Jan 1, 1950

By John W. Burd

A system is described for the simultaneous deposition of epitaxial layers on as many as eight substrates. A high degree of uniformity of both physical and electrical characteristics is achieved in the films. Variation of film thicknesses is consistently less than ±10pct within a wafer and from wafer to wafer within a run with the variation typically on the order of 55 pct. Composition variation of GaAs1-x PX layers within a wafer and from wafer to wafer within a run is consistently less than 51 pct. Electrical evaluation of the films by several techniques indicates excellent doping uniformity within a wafer and from wafer to wafer within a run. Mobilities for lightly doped GaAs films at 300°K are consistently >6000 cm2 v-1 sec-1 and mobilities > 7000 cm2 v- 1 sec-1 are regularly attainable. Techniques for the preparation of material with carrier concentrations from 1 x 1015cm-3 to 1 x 1019 cm-3 n-type and 5 x 1016 to 5 x 1018 cm-3 p-type are discussed. METHODS for the preparation of 111-V compounds by vapor phase reactions have been extensively reported in the literature.1-6 Almost all of the apparatus described for these various methods are suitable for processing one or at the most a very limited number of wafers simultaneously. With the recent rapid advances in the use of vapor grown GaAs for microwave oscillators and GaAs1-xPx as visible light emitters the requirements for these materials are steadily increasing. In order to satisfy these requirements it is necessary to move from a laboratory scale apparatus to one which is capable of processing a large number of wafers simultaneously. Desirable features would be a high degree of uniformity among the wafers and good reproducibility from run to run. The apparatus to be described fulfills these requirements very well. DISCUSSION The various methods reported in the literature can be classified under three headings: 1) closed tube, 2) open tube, and 3) the close-spaced method. Of these three the open-tube method is the most amenable for scale-up to a manufacturing process. It is the most versatile and the various operating conditions can be more precisely controlled than with the other two methods. A number of chemical reactions may be used to achieve vapor-phase growth of 111-V compounds. Sev-era1 of the more generally used reactions are shown in Fig. 1. All of these reactions have the following points in common: 1) generation of a volatile group III(Ga) species by the reaction of the transport agent (halide or HC1) with either Ga or GaAs, 2) introduction of the Group V(As and/or PI component, 3) a method of adding dopant, if desired, and 4) a region in which deposition from the vapor will occur and form as a single crystal epitaxial film on the substrates. The laboratory scale reactors permit the hot re-actant gases to flow into the relatively cooler deposition zone and pass successively over the several substrates which are arrayed along the long axis of the tube parallel to the gas flow. With this arrangement the composition of the reactant stream is continually changing as solid material is deposited on each successive substrate. As a result of this changing gas composition the reaction driving force also changes from substrate to substrate and the degree of uniformity of layer thickness, doping level, and so forth, is poor. This effect can be partially overcome by imposing a controlled temperature gradient along the deposition region to compensate for change in gas composition. However, even when this is done variations in layer thickness on the order of 30 to 40 pct are common and as high as 50 pct are frequently experienced between adjacent wafers in the tube. To expand this arrangement to a large number of wafers would only increase the nonuniformity from the first to last wafer in the line. From the above discussion the two undesirable features of changing gas composition and temperature gradient become evident. A reactor system which eliminates or minimizes these undesirable features is one in which the apparatus is mounted vertically as shown schematically in Fig. 2. The vertical mounting permits the disposition of a number of substrates on a suitable support so that all wafers are at the same vertical height in the furnace and hence at essentially the same temperature. By using only a single row of wafers the reactant gas mixture passes over only one substrate in its path through the reactor. Thus the two undesirable features of changing gas composition and temperature gradient are minimized. An additional design feature which further minimizes temperature variations is rotation of the substrate holder. Rotation serves to integrate any radial temperature gradient existing around the resistance heated furnace. A photograph of a reactor assembly at the completion of a run is shown in Fig. 3. MATERIAL PREPARATION Apparatus. Although any of the several chemical systems shown in Fig. 1 are adaptable for use in this apparatus the one generally used is System 2, the hydride synthesis system. This system has been de-

Jan 1, 1970

By R. K. Iyengar, G. C. Duderstadt

An investigation was carried out to determine the effect of Ca-Si additions on the dissolved oxygen content of liquid steel. An apparent equilibrium was reached after holding the melt for some time when the total oxygen content of the melt was identical with the dissolved oxygen. Results of the investigation show that for deoxidation with silicon and manganese the apparent equilibrium is reached after 8 to 12 min and the oxygen content of the melt is in good agreement with values reported in the literature for similar steel compositions. Ca-Si additions decrease the dissolved oxygen content appreciably below that obtained with Si-Mn deoxidation. It is postulated that some calcium dissolved in liquid steel at the time of its vaporization combines with dissolved oxygen to form CaO which then fluxes the manganese silicate, thereby lowering the activity of the deoxidation products. Slow flotation of calcium silicate inclusions is attributed to their slower growth rate. An addition of aluminum (to yield <0.005 pct Alsol) prior to introduction of Ca-Si improves the kinetics of removal of resulting deoxidation products. WITH the introduction of continuous casting of billets and blooms, application of calcium-containing alloys for deoxidation purposes has gained new interest. More so than in conventional ingot casting, the degree of control of the dissolved and total oxygen contents in steel for continuous casting can determine the success or failure of the operation because these affect both surface (pinholes) and internal quality of the billets. Of the available deoxidizers, only silicon has so far found wide application. However, in the typical range of application (0.20/0.30 pct Si), it is too weak a deoxidizer to suppress pinhole frequency to the level desirable for all but the least demanding appli-cations (approximately 10/50 pinholes per sq ft, de-pending on degree of subsequent reduction). On the other hand, Vincent&apos; has shown that it requires ap-proximately 0.007/0.008 pct A1 soluble in the steel to suppress pinhole formation to <10 pinholes per sq ft. In view of the difficulty of consistently maintaining this aluminum level and the associated problem of tundish nozzle constriction2 when aluminum is added to the ladle, steelmakers have searched for other de-oxidation alloys to circumvent the problem. Calcium-containing alloys offer such a possibility. When employed as a partial substitute for silicon, CaSi (30 pct Ca/60 pct Si) additions are reported to yield adequate pinhole contro1.3 Its use simultaneously preserves the "fluidity" of the steel and ensures good castability.4 Oxygen contents as low as 0.007 to 0.014 pct have been obtained with CaSi additions varying between 3 to 8 lb per ton.5-7 Due to the high degree of vaporization of calcium at the temperature of molten steel and the different methods used to introduce it into the liquid, the reported results show considerable scatter and lack of consistency. According to several investiga- deoxidation tors, the flotation characteristics of CaSi products are not as favorable as those found for alumi-num but are similar to those established for silicates with low alumina content.678 Thus, cleanliness ratings were improved when CaSi was replaced by a com-bination of Si + A1 followed by CaMnSi additions.5,9 In view of the lack of a comprehensive description of the deoxidation potential of CaSi alloys, a study was undertaken of the effect of CaSi additions on oxygen content in comparison to Si + Mn and Si + Mn + Al. The alloy chosen for this study contained 63 pct Si, 32 pct Ca, <3 pct Al, and 2.5 pct Fe. EXPERIMENTAL PROCEDURE The experiments were divided in three groups as shown in Table I. In each group, the CaSi addition was increased successively while maintaining the melt composition constant. The experiments in the third group were designed to determine the effect of prede-oxidation with small amounts of aluminum. Ingot iron, containing 0.02 to 0.03 pct C and 0.03 to 0.05 pct Mn, was melted in a 100-lb magnesia crucible. Pig iron was added to the melt under air in an induction furnace to attain the desired carbon content of 0.05 to 0.15 pct and thereby control the initial oxygen content of the melt between 0.04 and 0.015 pct. After removal of the slag, the furnace was sealed and argon was introduced through an opening in the graphite cover, Fig. 1. When the desired temperature was reached, electrolytic manganese was added to the melt and pin samples were taken (7 mm silica tubing) to establish initial oxygen content. To obtain maximum efficiency, CaSi and metallic silicon were introduced in a sealed steel pipe into the bath. This procedure assured minimum loss of calcium through vaporization as the deoxidants were always released at the bottom of the melt. Samples were taken at regular intervals and quenched in water. Temperature of the bath was measured with a Pt/Pt-10 pct Rh thermocouple. Portions of the pin sample were used for oxygen analysis; five determinations per sample were made to obtain average oxygen content. Oxygen analyses were made by the inert carrier gas fusion method with frequent cross checks with the vacuum fusion method.

Jan 1, 1970

By H. G. Doll

A new electrical logging method. called MicroLaterology is described. whereby the resistivity R of the invaded zone close to the wall of the bore hole is measured. This method essentially utilizes a system of concentric circular electrodes iml,edded in an insulating support which is applied to the wall of the hole. A beam of current of very small diameter is focused horizontally into the formations by means of an automatic control device. and then opens widely at short distance from the wall. with this method, R most often can be recorded directly. except when the mud cake is very thick. in which case a correction is easily provided. The basic role of factor R in the quantitative analysis of electrical logs in terms of fluid saturation and of porosity is explained. The paper is illustrated with field examples. INTRODUCTION In electrical logging. the resistivity of that part of the penneable and porous formations which is invaded by mud filtrate is an important factor in the interpretation. Measurements made with the conventional devices — normal. lateral — and also with improved systems as the Laterolog and induction logging&apos; — are very often more or less affected by the presence of the invaded zone. and the knowledge of the resistivity of this zone is useful in the evaluation of the true resistivity of the beds. which itself is a basic element for the determination of fluid saturation. Moreover. the comparison of the resistivity of the invaded zone with the resistivity of the mud filtrate gives valuable indications on the magnitude of the formation resistivity factor — which in turn is necessary for the quantitative interpretation of the logs. both in terms of fluid saturation and of porosity. On the other hand. it is generally admitted that the invaded zone is not a homogeneous medium separated from the uncon-tamirlated part of the bed hy a well defined cylindrical boundary. but that the fluid distribution—filtrate. connate water. hydrocarbon — and hence. the resistivity. in the invaded zone varies progressively with the distance from the wall of the hole. The term "resistivity of the invaded zone" therefore corre-sponds to an average value which is a function of the distribution of the fluids Inasmuch as the law of this distribution is not exactly known, the resistivity of the invaded zone is not a well defined factor. A much better definition is obtained if the medium under consideration is limited to that part of the formation which is within a short distance from the wall of the hole. It seems likely a within a distance of at least two or three in., most of the fluids in in the pores of tile formation have been displaced by the mud filtrate. The connate water has almost certainly been flushed out. and the oil. if any has generally been reduced to a comparatively small amount. The resistivity witliir~ the radial limit of two to three in. is. therefore. prac.tically constant at an). given level: its value. at least when the proportion of conductive solids in the formation is negligible. is chiefly dependent on the resistivity of the filtrate and on the porosity of the formation, and is affected only to a relatively small degree by the presence of the small amount of residual oil. This part of the formation close to the wall of the hole will he designated in the following as the "flushed zone." a-distinguished from the more general term of "invaded zone&apos;. which relates to the part of the formation extending from the wall out to the distance where the formation is completely uncontaminated. The symbol R,, will he used for the resistivity of the flushed zone. (The notation R is related to the radial distance from the hole. If x designates this distance. xo is the initial value of x, i.e., the value corresponding to the region very close to the wall.) The determination of R is difficult, if not impossible. from logs made with the conventional devices. The long normal and the long lateral are. of course. not suited for this purpose because their radii of investigation are by far too large. The short normal. and the limestone sonde—-after correction for the effect of the hole hole — give resistivity values which corre. spond to materials situated within a comparatively short distance from the hole, but this distance is still several time. as great as the thickness of tire flushed zone. The only value which can be obtained with these devices corresponds to an average resistivity of the invaded zone- — and this only provided the invasion is deep enough, since otherwise the meas "red values would also be affected by the uncontaminated region beyond the invaded zone. It should nevertheless be recalled that despite these limitations. the measurements given by the short normal and or the limestone sonde are always very useful for qualitative interpretation. and also in favorable cases for the qantitative analysis of the logs in terms of saturation and porosity. The MicroLog. which was primarily developed for the detection of permeable beds and for an accurate determination of their boundaries. provides a good approach towards the evaluation of R. In the case of hard formation.. however. The

Jan 1, 1953

By R. T. DeHoff

In any structural transfortnation which is driven by surface tension, the geometric variable of fimdamental importance is the local value of the mean surface curvatuve. Acting through the suvface free energy, this quantity determines the magtnitude of both the pressure and the chemical potential that develops in the neighborhood of an arbitrarily curved surface. A metallographic method which would permit the quaniitatiue estinzation of this propevty is of fundarnerztal irztevest to studies of such processes. In the present paper, it is shoun that the average value of the mean surface curvature in a structuve can be estimated from two simple counting measuretnents made upon a vepresentative metallograpIzic section. No simplifyirlg geonzetric assurmptions are necessary to this deviuation. It is further shoum that the result may be applied to parts of interfaces, e.g., interparticle welds in sintering, or the edge of growing platelets in a phase transformation, without loss of validity. In virtually every metallurgical process in which an interface is important, the local value of the mean surface curvature is the key structural property. This is true because the mean curvature determines the chemical potential of material adjacent to the surface, as well as the state of stress of that material. The theoretical description of such broadly different processes as sintering,1,2 grain growth,3 particle redistrib~tion4,5 and growth of Widmanstatten platelets8 all have as a central geometric variable the "local value of the mean surface curvature". The tools of quantitative metallography currently available permit the statistically precise estimation of the total or extensive geometric properties of a structure: the volume fraction of any distinguishable part:-&apos; the total extent of any observable interface,10,11 and the total length of some three-dimensional lineal feature:&apos; and, if some simplifying assumptions about particle shape are allowed, the total number of particles.&apos;2"3 The size of particles in a structure, specified by a distribution or a mean value, can only be estimated if the particles are all the same shape, and if this shape is relatively simple.14-16 The relationships involved in converting measurements made upon a metallographic section to properties of the three dimensional structure of which the section is a sample are now well-established, and their utility amply demonstrated. In the present paper, another fundamental relationship is added to the tools of quantitative metallography. This relationship is fundamental in the sense that its validity depends only upon the observation of an appropriately representative sample of the structure, and not upon the geometric nature of the structure itself. It involves a new sampling procedure, devised by Rhines, called the "area tangent count". It will first be shown that the "area tangent count" is simply related to the average value of the curvature of particle outline in the two-dimensional section upon which the count is performed. The average curvature of such a section will then be shown to be proportional to the average value of the Mean surface curVature of the structure of which the section is a sample. The final result of the development is thus a relationship which permits the evaluation of the average value of the mean surface curvature from relatively simple counting measurements made upon a representative metallographic section. The result is quite independent of the geometric or even topological nature of the interface being studied. QUANTITATNE EVALUATION OF AVERAGE CURVATURE IN TWO DIMENSIONS The Area Tangent Count. Consider a two-dimen-sional structure composed of two different kinds of distinguishable areas (phases), Fig. l(a). If the system is composed of more than two "phases", it is possible to focus attention upon one phase, and consider the remaining structure as the other phase. The reference phase is separated from the rest of the structure by a set of linear boundaries, of arbitrary shapes and sizes. These boundaries may be totally smooth and continuous, or piecewise smooth and continuous. An element of such a boundary, dA, is shown in Fig. l(b). One may define the "angle subtended" by this arbitrarily curved element of arc, dO, as the angle between the normals erected at its ends, Fig. l(c). Now consider the following experiment. Let a line be swept across this two-dimensional structure, and let the number of tangents that this line forms with elements of arc in the structure be counted. This procedure constitutes the Rhines Area Tangent Count. Suppose that this experiment were repeated a large number of times, with the direction of traverse of the sweeping lines distributed uniformly over the semicircle of orientation.&apos; Those test lines which ap- proach from orientations which lie in the range O to O + dO form a tangent with dA; those outside this range do not, see Fig. l(c). Since the lines are presumed to be uniformly distributed in direction of traverse, the fraction of test lines which form a tangent with dA is the fraction of the circumference of a semicircle which is contained in the orientation range, dO; i.e., vdO/nr or dB/n. If the number of test lines is N, the number forming tangents with dA is N(d0/n). Since each test line sweeps the entire area of the sample, the total area traversed by all N test lines is NL2. The number of tangents formed with dA, per unit area of structure sampled, is therefore

Jan 1, 1968

By B. A. Wilcox, A. H. Clauer

The steady-state creep of TD Nickel NL + 2 001 pct TltOz) has been studied orer the telirperatve range 325&apos; to 1100O and the stress range 15,000 to 36,000 psi. At high temperatures (aboue 0.5 T& gran-boundary slzding is the )nost znportant )node of creep deformation, and the steady-state creep rate, is, can be related to stress and temperature by: where Q = 190 kcal pev mole and n has an unusually high value of 40. A creep mechanism based on cross slip of dislocations around The O2 particles can satisfactovily explain the low-temperature (T < 0.5 T,) cveep behavior, and the follo wing relation is applicable: Q, (a) is found to decrease from 57 to 46 kcal per mole as the stress is increased from 32,000 to 36,000 psi. THERE have been a variety of theories proposed to explain the influence of dispersed second-phase particles on the yield strength and flow stress of metals, and these have been reviewed recently by Kelly and icholson.&apos; However, only several attempts2"4 have been made to develop mechanistic treatments which characterize the creep behavior of dispersion-strengthened metals, and to date these have not been fully evaluated experimentally. weertman2 and Ansell and weertman3 proposed a quantitative creep theory for coarse-grairzed dispersion-strengthened metals, based on the concept that the rate-controlling process for steady-state creep was the climb of dislocations over second-phase particles, as suggested by choeck. The theory predicted that the steady-state creep rate, <,, was proportional to the applied stress, a, for low stresses and that is a4 o for high stresses. The activation energy for creep, Q,, was equivalent to that for self-diffusion, Qs.d., in the matrix. Some limited experimental evidence in support of this theory was obtained on a recrystallized Al-Alz03 S.A.P.-type alloy by Ansell and Lenel.6 Ansell and weertman3 also developed a semiquanti-tative theory for high-temperature creep of lineg-rained dispersion-strengthened metals in order to explain their results on an extruded S:A.P.-type alloy, which had a fine-grained fibrous structure. They suggested that the rate of dislocation generation from grain boundaries was the rate-controlling process, and fitted their results to the equation: where Q, was found to be 150 kcal per mole, i.e., QC- 4Q,.d. in aluminum. Similar high activation energies for creep7-&apos;&apos; and tensile deformation" of dispersion-strengthened alloys have been observed by other investigators for S.A.P.,&apos;" indium-glass bead omosites, and Ni + A1203 alls.&apos; There is no general agreement regarding the mechanisms involved in the creep of dispersion-strengthened metals, and this is due in part to the lack of detailed studies relating the structures of crept specimens to the mechanical behavior. The present investigation on thoriated nickel was undertaken with the aim of studying the structural changes which occur during creep of a dispersion-strengthened alloy and rationalizing the observed mechanical behavior in terms of the creep structures. EXPERIMENTAL METHODS The material used in this investigation was 1/2-in.-diam TD Nickel bar, which contained 2.3 vol pct Tho,. Obtained from E. I. duPont de Nemours & Co., Inc. The final fabrication treatment by DuPont consisted of -95 pct reduction by swaging followed by a 1-hr anneal at 1000°C. Transmission and replica electron microscopy revealed that the material had a fine-grained fibered structure with an average transverse grain size of -1 p and a longitudinal grain size of 10 to 15 p. Selected-area diffraction indicated that the fiber axis was parallel to (OOl), in agreement with the results of Inman eta1." All creep specimens were vacuum-annealed at 1300°C for 3 hr prior to testing. Transmission electron microscopy showed that the only structural change due to annealing was a slight decrease in dislocation density, confirming the reported high degree of structural stability.13 Furthermore, recrys-tallization or grain growth during creep was never observed. The structure typical of uncrept material (after the 1300 C, 3-hr anneal) is shown in Fig. 1. The grain boundaries are predominantly high angle and. although some areas show a tangled cell structure, the grain interiors are relatively dislocation-free. Individual dislocations are strongly pinned by the Tho2 particles; i.e., very rarely did dislocations move within a thin foil. The grey "halos" around some of the larger particles which protrude out of the foil surface arise from contamination in the electron microscoge. The Tho, particle size ranged from -100 to IOOOA, and the distribution is shown in Fig. 2. The technique used to obtain the data in Fig. 2 consisted of dissolving the nickel matrix in acid, collecting the Tho2 particles on cellulose acetate, and measuring about 1000 particle diameters in the electron microscope. Similar results were obtained by measuring about 600 particles in thin foils, an; the average particle size was found to be 2r, = 370A. Using the data in Fig. 2 (annealed structure), the mean planar center-to-center particle

Jan 1, 1967

By Paul C. Merritt

The story now unfolding on the Mesabi Range is more than just another chapter in the continuing history of iron mining. It is an epic of foresight, research and pioneering instinct just now culminating in the rapid growth of a new industry hardly more than ten years old. And that growth has been impressive. In the decade that has passed since Reserve Mining Co. blazed a trail as the first successful large- scale commercial taconite operation, the number of plants now existing or soon to be operating has grown to six. From Reserve&apos;s initial capacity of 3 million tons of pellets per year, total production capacity on the Range has surged to 31.5 million tons while capital investment has leaped from $300 million in 1955 to almost $1 billion today. During the past year alone, more than $500 million has been committed to these projects, an amount probably greater than that going into any other single mining area in the world. There is more yet to come.

Jan 10, 1965