Search Documents

By E. B. Snyder, H. M. Kraner

This paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, partitularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercia1 blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. Factors Affecting Choice of ._ Refractories If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing tempera- . ture, which he in turn internrets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and re-. sistance to the action of slag. In most refractory applications . several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient Stages and the Progress is determined by measuring slight changes in porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures at which they are to be used, although in many cases it would be desirable from the user's point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. Both may occur in the same refractory containing two such clays.

Jan 1, 1944

By H. M. Kraner, E. B. Snyder

This paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, partitularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercia1 blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. Factors Affecting Choice of ._ Refractories If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing tempera- . ture, which he in turn internrets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and re-. sistance to the action of slag. In most refractory applications . several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient Stages and the Progress is determined by measuring slight changes in porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures at which they are to be used, although in many cases it would be desirable from the user's point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. Both may occur in the same refractory containing two such clays.

Jan 1, 1944

By R. E. Anderson, R. S. Busk

The mechanical properties of many nonferrous alloys can be modified by heat-treatment. This is almost always effected by controlling the amount of alloy in solid solution and the amount and distribution of second-phase material. The latter often is accomplished through precipitation or age-hardening treatments. The procedure is to solution-heat-treat the metal to provide a supersaturated solid solution and then cause precipitation of the dissolved material at some temperature below the solvus for the alloy. The generally used magnesium sand-casting alloys arc based on the ternary alloy system Mg-Al-Zn. Solid diffusion reactions in the system are slow enough so that a substantially completely supersaturated solulion is maintained even though the metal is relatively slowly cooled from heat-treating temperatures. Consequently, it is general practice to air-cool magnesium-alloy castings from the heat-treatment temperature prior to aging at an elevated temperature. Since it is necessary with many other alloys to cool quite rapidly before aging if optimum benefit from the aging is to be obtained, this study was undertaken to determine the effects of quenching on magnesium alloys. The] alloys used are shown in Table I, being selected as typical of the presently used magnesium alloys. Cooling Rates Since quenching is a means of rapidly extracting heat, there are two factors of interest in its study: (I) the rates of cooling that can be obtained and (2) the effect of various rates on the as-cooled as well as subsequently aged metal. The cooling rates were measured by drilling a hole 1/16- in diameter longitudi~lally in the center of a cylinder % in. in diameter and 3 in. long. The drilling was stopped to place the end of the hole at the center of the long axis of the cylinder. An iron-constantan thermocouple was inserted in this hole and wedged in place. The temperature drop during rapid quenching was recorded by a special1y built General Electric potentiometer recorder capab1e of measuring ' 500°F. temperature drop in 1/10 sec. For the slower cooling rates in air or oil, the temperature drop was measured by a Leeds and Northrup potentiometer recorder with the chart speed increased to One inch per minute' The cylinder was heated to the desired temperature, quenched as desired, and the temperature-time curve recorded. The cooling rates in still air, in oil at 350°F., in water at 180°F. and in a cold, high-pressure water spray were determined in this manner. The results of this study are presented in Fig. I. There is a great difference between water quenching and either air or oil quenching. There is little difference between the hot water quench and the cold water spray. Cooling rates were also

Jan 1, 1945

By Avnulf Muan, Egil Aukrust

The activity-composition curve for cobalt oxide in (Co,Fe)304 solid solutions with spinel-type stmcture has been determined experimentally by studying the equilibrium between the spinel phase and a coexisting cobaltowüstite phase, "(Co,Fe)O", at 1200°C. A large negative deviation from ideal behavior prevails in the spinel at low cobalt oxide concentrations and a positive deviation at high cobalt oxide concentrations. The activity-composition curve for iron oxide in the solid solution is determined from the above curve by integvation of the Gibbs-Duhem equation along the join Co3O4,-Fe3O4. The standard free energy of formation of cobalt ferrite, CoFe2O4, from the oxide components CoO and Fe2O3 is calculated to be -8.2 kcal. ThERMODYNAMIC properties of (CO,Mn)3O4 solid solutions with spinel-type structure have been presented recently.' The present paper deals with similar relations in another spinel solid-solution phase, that represented by the system Co3O4-Fe3O4. The principles involved in measurements and calculations of thermodynamic properties for the system Co3O4-Fe3O4 are analogous to those used and discussed in detail in the work on (CO,Mn)3O4. A (CO,Fe)3O4 solid solution coexists in equilibrium with a (Co.Fe)Ot solid solution over a considerable Here acOo1.33 and aao are the activities of cobalt oxide in the spinel and the oxide solid solutions, respectively, pO2, is the oxygen pressure of equilibration, and pb, is the oxygen pressure at which CoO and CosO4 coexist in equilibrium in the binary system Co-O at the same temperature. The activity-com position curve for cobalt oxide in the (Co,Fe)O solid solution in contact with metal has been determined in a previous investigation by the present authors.' The system shows a small positive deviation from linear behavior. Because of the large defect concentration in wiistite and in (Co,Fe)O solid solutions, one cannot assume that the activity-composition relations in the oxide phase coexisting with a spinel phase at relatively high oxygen pressures are the same as those prevailing in the oxide solid solution coexisting with metal. However, a Gibbs-Duhem integration over the ternary Co-Fe-0 solution can be used to determine activities of cobalt and iron, and hence of CoO and FeO, from a knowledge of the oxygen potentials. Several papers have dealt with the subject of application of the Gibbs-Duhem equation to multi-component systems. 3-6 In the present case, it was

Jan 1, 1964

By Hobart M. Kraner, E. B. Snyder

THIS paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, particularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercial blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. FACTORS AFFECTING CHOICE OF REFRACTORIES If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing temperature, which he in turn interprets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and resistance to the action of slag. In most refractory applications several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient stages and the progress is determined by measuring slight changes in. porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures . at which they are to be used, although in many cases it would be desirable from the user's point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. -Both may occur in the same refractory containing two such clays.

Jan 1, 1944

By Nathaniel Hen

IN the United States, in the 2 1/2 years since the rescinding of the wartime order closing gold mines, conditions have not yet returned to normal. Shortages of man power have prevented some mines from operating at all, and most of those in operation are still at reduced capacity. This fact, combined with shortages of materials, the high cost of supplies and labor, high tax rates, and a fixed price for the product have made the past years rather rough ones for gold producers. In foreign countries conditions are rather similar. In Canada several new mines are coming into production and some others are enlarging. Costs have not increased as much as in the United States and gold production is being encouraged. Recently a bonus of 20 per cent on increased production has been proposed. In South Africa, where gold mining is of major importance in the national economy the industry is also in a favored position with government; new discoveries of major importance there will markedly increase the gold output. Demand for labor is rap-

Jan 1, 1948

By Lawrence Adler

A lag apparent in the mining engineering field. While mining will continue as an essential industry, a revitalized profession will be required for national well-being. Specific problems facing the profession include: - a conflict between its design, production and management components, which affect the engineers on a daily basis; - a credibility gap in public matters that is so extreme, government action approaches punitive in degree, and - historical decreases in the number of degree-offering departments in the face of an increasing demand for graduates. A turnaround in these areas could result in attracting into the industry, highly creative, capable, and socially concerned engineers. By improving the quality of undergraduate education, the effectiveness of each entering engineer would be multiplied. This is another way to combat the chronic shortage of trained mining engineers. At the same time, it would set a significant example for other professions in the throes of overspecialization. A revival of the mining profession can be accomplished only during the formative training years of its future practitioners. An educator's role would be pivotal in this effort.

Jan 3, 1975

In connection with the presentation of his paper in oral abstract, Mr. Hansell exhibited samples of briquettes, showing their porosity, and the change of surface produced by burning. Alfred H. Cowles, Sewaren, N. J.—I am familiar with this furnace, and I wish to point out that the larger it is, the greater is its efficiency, and the longer its life. In Europe, experiments have been made with small, short furnaces of this character, accommodating narrow cars; whereas Mr. Hansell says that there is in this country a furnace 180 ft. long .and 10 ft wide. The American furnaces, moreover, differ in design from those used in Europe; and we may expect from these larger furnaces not only greater efficiency, but also greater durability —the latter advantage being due to the fact that, in these large furnaces, projecting brick walls of greater thickness can be provided, to prevent the heat from attacking the sides of the cars, by means of bricks which, over-reaching these iron surfaces, furnish a protective cover to them. In other words, in these

Jan 1, 1913

By Howard N. Hall

The compressibility of reservoir rock is a factor which is generally neglected in reservoir engineering calculations. This is due in part to the fact that there is little published information on rock compressibility values for limestones and sandstones. Omission of rock compressibility is undoubtedly justified in calculations for saturated reservoirs; however, in under-saturated reservoirs,* expansion of the rock accompanying decline in the reservoir pressure may be of such magnitude as to affect materially the prediction of reservoir performance. The effect of rock compressibility will be of most importance in: (1) calculation of oil in place by pressure decline data in undersaturated volumetric reservoirs when the limits of the field are unknown or indefinite, and (2) studies of natural water drive performance. To estimate its importance in such cases, a series of laboratory tests were made to obtain usable values for reservoir rock compressibility. The total, or effective, compressibility of any reservoir rock is a result of two separate factors, namely, expansion of the individual rock grains, as the surrounding fluid pressure de-

Jan 1, 1953

Zinc is just now a very important metal. Its use in cartridges and shrapnel brass are in the public eye. But its uses after the war are no less important. Brass as an engineering material for electrical machin-ery, journal bearings, and plumbing fixtures takes fully 50 per cent. of the production, and its use in these lines would have been increased in the last few years but for the price. Its use for barbed wire is probably more in war time than in peace. In the composition of paints, it is becoming more and more necessary. One of the forms of pigment, litho- pone, is the base of nearly all interior wall paints; of all the sanitary enamels for bath-rooms and bath-tubs, and is now in great demand. Zinc oxide is also increasing in use for paint, and for manufacture of linoleum. When we realize that this district-Missouri, Oklahoma, Kansas and Arkansas-produces now over one-third of the zinc ore of the world, it is at once seen that a meeting where the geology, mining, concentration

Jan 6, 1917

By R. D. MacDonald

The search for metalliferrous deposits in the Labrador-Ungava Trough of Canada dates from 1929 when non-ferrous minerals were the main quest of prospectors in this area. Many gossans, resulting from the oxidation of sulfides, were located and examined but none of these led to any orebodies of commercial value. However, such investigations did much to arouse interest in this area and fostered further mapping and prospecting. Since this early period in the history of prospecting in the Trough, the presence of iron ore deposits and potential iron producing sites has commanded the center of attention of exploration personnel. The iron-bearing rocks of southwestern Labrador have in recent years come into prominence as possible sources of iron ore of the beneficiation type. Exploration and development work has been carried on in concession areas granted by the Newfoundland Government to the Labrador Mining and Exploration Co. Ltd. and to the Newfoundland and Labrador Corp. In the course of evaluating its holdings in the Wabush Lake area (Fig. l), Labrador Mining and Exploration Co. has conducted geological, geophysical and diamond drilling programs.

Jan 10, 1960

By R. Costantini

Long-distance transportation of solids by hydraulic pipelines holds promise of great economic benefits. In most mineral processing plants today, moving of solids in slurry-form by pipeline is commonplace. Yet in spite of this, the method is slow in being adopted on a broad scale for moving solids over distances of many miles. This is especially surprising in view of the successful realization of two daring ventures in long-distance solids pipelines in this nation within the last five years. One is the 72-mile long, 6-in. diam. pipeline of the American Gilsonite Co. which has been satisfactorily transporting 700 tpd of gilsonite from the mine at Bonanza, Utah, to the processing plant at Grand Junction, Colo., since April 1957. The other is the 108-mile long, 10-in. pipeline of the Pittsburgh Consolidation Coal Co., which has been transporting about 4000 tpd of finely crushed coal from the mine at Cadiz, Ohio, to the Eastlake Power Plant of the Cleveland Electric Illuminating Co. since January 1958.

Jan 8, 1961

By V. S. Rood

Typical System of Workings THE general system of workings at the Utah-Apex is similar to that found in many of the western metalliferous mines. There is a vertical three-compartment shaft extending to the surface, from which the various levels have been driven to the orebodies. The 1000-ft. (305-m.) level, about ¾ mile long, was driven as a haulage and drain adit. Geology The formation is a flat north-dipping series of alternating limestone and quartzite beds. Extensive north-south faulting and-fissuring have taken place, resulting in the formation of large replacement orebodies in the crushed zones in the limestone. The orebodies are irregular in shape and size, but follow closely the trend of the mineralizing fissures. The ore consists of galena, pyrite, sphalerite and small values in silver and gold. Large masses of non-commercial pyrite are frequently found in or adjacent' to the orebodies, and more or less pyrite is found for some distance in the walls of the orebodies. Lenticular bodies of a black pyritic shale also occur in the zones where extensive faulting has taken place.

Jan 6, 1918

By D. F. Stoneburner, G. Derge, Ling Yang

PREVIOUS investigations in this laboratory have shown the existence of electronic conduction in several molten metal sulfides and the specific conductance of a number of these has been measured as a function of temperature.' In order to better understand the electronic nature of these melts, the thermoelectric power of a molten FeS-solid tungsten thermocouple was measured and a value of approximately 55 µv per "C was obtained in the temperature range from 1200" to 1400c2 These studies have been continued and the thermoelectric power of several other molten metal sulfide-solid tungsten thermocouples have been obtained. The experimental arrangement is shown in Fig. 1. A Kanthal furnace was used, doubly wound to prevent any undesirable effects of an external field. A 1/2-in. McDanel tube was fitted with two vertical 5/8-in. McDanel tubes as shown. These tubes were about 2 in. apart. A graphite boat was used to hold a re-crystallized alumina boat in which the prefused sulfide was placed. Two probes were made using

Jan 1, 1960

By Susanne Pignolet, Richard D. Hagni

Ore microscopy has been applied to the complex cobalt-nickel- copper-lead-zinc ores from the Madison Mine in the Fredericktown subdistrict of the Southeast Missouri Lead District to predict potential beneficiation problems. It has been found that in some portions of the ore deposit, textures are present which may result in metal losses. In ores from the Bonneterre Transition Zone the intimate association of siegenite with chalcopyrite may result in cobalt and nickel losses to the copper concentrate and nickel contamination of the copper matte at the smelter. In ores from high stratigraphic horizons, this association is relatively uncommon, and siegenite is commonly associated with bravoite. This latter association will increase the the recovery of cobalt and nickel in the siegenite concentrate. However some cobalt and nickel will be lost to the tails as bravoite-pyrite particles due to the intimate intergrowth of these minerals. Other textures which may result in beneficiation problems include the intimate intergrowth of chalcopyrite and galena and the occurrence of sphalerite as inclusions in galena.

Jan 1, 1984

By C. W. Vaupell

THE Huitzuco mines lie in north central Guerrero, Mexico; production has been about 90,000 flasks of quicksilver since 1873. Near-surface ores fill extinct mud geysers and the deep deposits are chambered veins, stock-works in brecciated blocks, and replacements in limestone. The epigenetic minerals livingstonite, stibnite and sulphur occur in limestone, gypsum and dolomite through a developed vertical range of 260 meters. The deepest workings expose an increased amount of stibnite, which probably indicates that the lower limit of mercury mineralization is being approached. A resur-gence of heat and water formed geysers over an extended area after the period of mercury mineralization. Mud geysers, which are situated, in the outcrops, contain the secondary mercury minerals, cinnabar and barcenite in the gravel and mud filling the vents. A 150-ton flotation plant is in operation concentrating stope fills that assay 3.0 kg. of mercury per ton. In one open stope, which is more than one hectare in area and 60 m. high, 150,000 tons are available.

Jan 1, 1937

By Charles Morgan

AN increased demand for brown iron ore in the Birmingham district during the past 18 months has caused renewed activity both in prospecting and mining these ores. In recent years the production in Alabama has ranged from 41,559 tons in 1932 to 639,351 tons in 1928. During the last 9 years about 83 per cent of the total brown ore produced in the United States has come from Alabama (Tables 1 and 2). PROSPECTING Two methods of prospecting are used in this district: (1) test pits, (2) churn-drilling. Usually there is certain quite definite information on an area to be prospected; some of the indications are float ore such as small gravel or small and large boulders known as "dornicks" scattered over the surface, and ore exposed by erosion in gulleys and ravines, which have cut or eroded through the overburden. Often these natural erosions furnish an indication of the thickness of the ore and to some extent of the area of the ore body.

Jan 1, 1937

By J. W. Onuscheck

The oxygen-fuel oil burner lance is a very useful tool at the Monessen B.O.F. It increases the overall flexibility of the operation. An additional 15,000 to 20,000 ingot tons can be produced at a given hot metal supply. It helps overcome sporadic drops in hot metal thermal values and/or supply. It results in increased yield, in particular, on high carbon heats where much yield was lost on reblow triggered slag reactions. The burner has also been adopted as a standard tool to aid burning in new vessel linings. Overall, steelmaking performance has improved with the use of standard preheat practice. Scrap charges up to 50 percent have been used routinely in times of extreme hot metal shortages, but the performance is weak in some categories. Development of a single step oxy-oil process is in progress. In this process, scrap and hot metal are charged as in the normal B.O.F. practice, but fuel oil is fired with the refining oxygen.

Jan 1, 1972

The greatest mining center in the state of Utah is the incorporated town of Bingham about twenty-five miles southwest of Salt Lake City. The principal industry of this vicinity, prior to the early fall of 1863, was lumbering and the first saw-mill in the state was built near the mouth of Bingham Canyon. Early in the fall of that year. George B. Ogilvie discovered gold and shortly afterward the first mining district in the state was organized. Some writers place the discovery of gold in the canyon in the late fifties. If this be so, however, the matter was kept extremely quiet because no mining was engaged in until after Ogilvie's discovery. Bingham was a placer mining camp, producing about one million dollars' worth of dust and nuggets from placers up and down the canyon and in Bear Gulch until early in the seventies, or about ten years after the discovery of gold, when a large body of argentiferous lead ore was discovered and soon after heavy shipments were made from a half dozen or more properties.

Jan 1, 1925

By W. C. Hellyer, R. A. Campbell

In single-stage autogenous grinding, the buildup of a critical size fraction in the media can be corrected by removing this material through pebble ports, crushing it below the critical size range, and recycling the crusher product back to the mill. The rate at which the critical sire fraction is crushed affects the size distribution of the grinding media and this in turn affects the sire distribution of the grate discharge. This provides a means for controlling the grind produced by a single-stage autogenous grinding unit. The pilot-plant investigations on a very hard copper ore were carried out at the facilities of the Institute of Mineral Research, Michigan Technological University. In an autogenous grinding circuit in which feed at approximately 9 in. top size is reduced to a size suitable for subsequent processing, the build-up of a "critical size" fraction in the media causes problems. A "critical size" fraction has been defined as, "media too small to effect reduction by impact grinding of ore coarser than a quarter of an inch and too large to be broken by the largest size of media in the charge."' The buildup of a critical size fraction reduces the capacity of the mill, increases the grinding power requirements per ton of finished product, and generally produces a finer grind than is desired. It is general practice to overcome this problem by the addition of large-diameter steel balls to the grinding charge. This has certain disadvantages, such as 1) an increase in mill liner wear, 2) wear on the steel balls, and 3) some loss in flexibility in grinding circuit opera-tions resulting from difficulties in removing the steel balls by means other than by grinding out. A number of investigators' have suggested the use of a small crusher as an alternative to the use of large steel balls for control of a critical size fraction. With this technique the critical size fraction is removed from the mill continuously through suitable-sized pebble ports, crushed below the critical size range, and returned to the mill. An external crusher would cause no increase in mill liner wear, the wear on the crusher would be less expensive than the wear on the steel balls, and the flexibility of the grinding circuit operations would be enhanced since the crusher can be cut into and out of the circuit at will. This paper describes an autogenous grinding pilot plant investigation on a very hard copper ore, which led to the selection of an autogenous grinding flowsheet incorporating a crusher in the circuit as the preferred method for grinding this ore. Further development of the technique demonstrated that the crusher could be employed to control the product produced by an autogenous grinding unit. Description of Pilot Plant These investigations were carried out at the pilot-plant facilities of the Institute of Mineral Research, Michigan Technological University, Houghton, Mich. The autogenous grinding unit was a 6-ft-diam by 2-ft-long Hardinge Cascade mill with %-in. slotted steel grates. Pebble ports cut into the grates allowed passage of pebbles having a top size of approximately 21/2 in. The grate and pebble-port discharge material passed over a 3/16-in, trommel screen with the trommel under -size being pumped to the classification device. DSM screens were employed for classification in the early investigations, but were replaced later by a small Dorr rake classifier. The trommel oversize material returned to the mill via scissor conveyors. When the crusher was incorporated into the circuit, the trommel oversize material passed to a double-deck vibrating screen fitted with 2-in. and 3/4-in. square mesh screen cloths. The $ 2-in. and the —2 +3/4-in. size fractions were combined and crushed to a nominal 1 in. in a 4 x 6-in. jaw crusher. The crusher discharge and the —3/4-in. screen undersize returned to the mill. In the final investigation, a flap gate fitted to the top deck of the screen directed the — 21/2 +2-in. size fraction to the crusher or back to the grinding mill. The flap gate operated manually on a 15-min cycle, with this material being crushed for so many minutes out of each cycle. This was found to be a more reliable method of controlling the amount of — 21/2 +2-in. material crushed than attempting to make a split of a small weight of material on a continuous basis. Operational Techniques: Each sample was sized into three fractions and the Cascade mill feed was reconstituted from these size fractions in the proportions existing in the original sample. Sufficient feed for 15 min operation was weighed out and fed by hand over a 15-min period. The gross mill power draft was recorded every 15 min, corrected for tare power and drive efficiency, and reported as net kilowatt-hours per ton. A recording kilo-watt-hour meter provided a continuous visual record of the power drawn by the mill. Pulp densities of the trommel undersize and the classifier overflow (or DSM undersize) were taken every 15 min. The classifier overflow was sampled automatically. Timed samples of the classifier sands were taken every 15 or 30 min, weighed, and returned to the circuit. After correcting for moisture content, the weights were converted into percent circulating load. Timed samples of the +2 in., the —2 + 3/4-in., —3/4-in. screen fractions, and the crusher discharge, were

Jan 1, 1971