Search Documents

By A. U. Seybolt

A. U. Seybolt (General Electric Research Laboratory)— As pointed out in an earlier paper,41 it appears to be very difficult to nucleate Si3N4 in Si-Fe of silicon content up to around 5 pet. Therefore, one observes, as did Pearce, that equilibrations with nitrogen gas yield only nitrogen in solid solution at temperatures above about 700°C, or, as Pearce found, 770°C. Evidently, the free energy of formation of Si3N4 only becomes high enough at -770°C to overcome the reluctance of Si3N4 to nucleate. However, as mentioned in Ref. 41, if some Si3N4 is first formed by a mixture of ammonia and hydrogen, one can then replace this gas mixture by nitrogen gas, and either increase or decrease the amount of Si3N4 present at any temperature by suitable adjustment of nitrogen pressure: that is, to equilibrate with Si3N4. In the equilibration experiments cited in Ref. 41, equilibrium was approached from both sides, and it was found that samples up to 944oC, at least, were in equilibrium with Si3N4. Higher temperatures were not employed, as this would have necessitated a redesign of the apparatus for using nitrogen pressures in excess of 1 atm. To summarize, the results of Pearce's experiments and those of Ref. 41 cannot be directly compared because two quite different equilibria were studied. Therefore, the statement by Pearce on p. 1398 indicating apparent error in Ref. 41 is unjustified. M. L. Pearce (author's reply)— There was limited evidence obtained in the current investigation which would indicate that excessive "supercooling" did not occur. A small piece of the same resulting from heat treatment No. 5 in Table III was subsequently held at 800°C for 16 hr in 95 pet N-5 pet H. Isotope-

Jan 1, 1964

By W. V. Green

Creep of tantalum was measured at temperatures from 0.6 to 0.89 of the absolute melting temperature. The creep curves include first, second, and third stages. Steady-state creep rate depends on the fourth power of stress. The activation energy for creep throughout this temperature range is approximately 114 kcal per mole, measured by the aT technique. Subgrain formation occurs as a result of creep strain, and pile-up dislocation arrays are observed in etch-pit patterns. BECAUSE of its high melting point-which is exceeded only by those of rhenium and tungsten—and its high room-temperature ductility compared to most of the other high-melting-point metals, tantalum will undoubtedly be utilized in an increasing number of high-temperature applications. Alloying studies directed toward increased high-temperature strength must use data on tantalum itself as a base line in order to evaluate the effectiveness of the alloying additions. However, to date, no systematic study of creep of tantalum at temperatures above one-half of its melting point has been reported in the literature. Conway, Salyards, McCullough, and Flagella1 have measured linear creep rate of tantalum sheet as a function of stress, but at only one temperature, 2600°C. This paper describes a relatively thorough study of the high-temperature creep of tantalum. METHOD Material Tested. The commercially supplied, l/2-innch-diameter tantalum rod used for this work was electron-beam-melted, cold-forged, rolled, swaged, cleaned chemically, and vacuum-annealed for 1 hr at 1000°C, all by its manufacturer. The vendor's analysis included 60 to 170 ppm C, 3.4 to 4.2 ppm H, 60 to 80 ppm 0, 15 ppm N, and a hardness ranging from 66 to 81 Bhn and averaging 76 Bhn. Creep eimens Used. Two creep-tested specimens are shown in Fig. 1. The 1/4 in.-diameter gage section was 3/4 to 1 in. long, and terminated either at shoulders 5 mils high or at 20-mil-diameter tantalum wires spot-welded to the circumference of the gage section. Both kinds of shoulders served equally well as fiducial marks for optical strain measurements. The spot welding did not alter the creep behavior in any detectable way; the 5-mil- high sharp shoulders did not result in any detectable localized effect on the strain. Before testing, each tensile bar was first mechanically polished -id then electrochemically polished according to the method referred to by Forgeng2 as the "Thompson Ramo Woolridge" method, which was suitable for tantalum after small adjustments of technique were made. Two tensile bars tested at low stresses had 1/8-in.-diameter gage sections and utilized only the weight of the bottom grip for the applied load. Although these diameters were smaller than were desired for other reasons, applied loads were known with high precision in the tests in which they were used. Testing Procedure. Two different constant-load creep-testing machines were employed, one of which has been described by Smith, Olson, and Brown.3 In both, the tensile bar is held vertically on the axis of a cylindrical tungsten tube or screen heater by threaded tungsten grips. The tensile bars and associated grips are heated by radiation from the incandescent heaters, which are heated by their own electrical resistance. Both testing machines use pins to hold the bottom grips in place. The load is applied to a tensile bar through hanging weights, a constant force-multiplication lever, a pull rod sealed to the chamber lid, and a top grip threaded to the pull rod at one end and to the tensile bar at the other. In one machine, the vacuum seal is a bellows with a low spring constant; in the other, the seal involves a rotating "0 ring". With the latter, rotation is converted to translation with a crank shaft, so that elongation of the tensile bar is accommodated with no change of tensile load. The incandescent tensile bar is viewed by an external optical system through slots in the radiation shields and heater, and an enlarged image is projected on a ground-glass screen. Gage-length measurements are made on this image with cathetometers on traveling microscopes. With regard to creep-test results, the two machines were identical. Thorium oxide coatings were applied to the threaded ends of the tensile bars, to prevent diffusion welding of the tensile bars to the grips during testing. Specimen temperatures were measured with an L. & N. optical pyrometer which had been calibrated against a standard carbon arc, and were corrected fir window absorption by calculation from the measured spectral transmittance of the quartz observation windows. Longitudinal temperature gradients in the tensile-bar gage length and temperature drifts during testing were detectable but small, and were estimated to be 10°C or less. Accuracy of temperature measurement was confirmed by comparing the temperature measured on the surface of a special

Jan 1, 1965

By E. E. Brownson

THIS paper will be confined to the treatment of methods as applied in the laboratory of the Boston and Montana Reduction Department of the Anaconda Copper Mining Co. at Great Falls, Mont. As the electrolytic plant of this company operates at a current density of approximately 35 to 40 amperes per square foot when running up to capacity, the arsenic and antimony content of the anodes delivered to the, plant is of considerable importance as bearing on the purity of the refined cathodes turned out. Owing to the rather high relative percentage of antimony, it has always been the custom to determine antimony as well as arsenic in all forms of copper. Thus, anodes have been analyzed in which the antimony was about equal to the arsenic although the average shows about 2 parts of arsenic to 1 of antimony. In the refined copper the relative proportions of the two impurities vary considerably, but probably in the average are about equal. In this latter case, the percentage of the two is so small that ordinarily no attempt is made to separate them, the report of analysis showing percentage of As and Sb combined. Although rapid and exceedingly accurate determinations of arsenic may be made by means of various distillation schemes, the determination of antimony, either by itself or together with arsenic, has always been more or less cumbersome and has required a considerable amount of time. By the methods, details of which follow, the determination of arsenic and antimony, either separated as in the case of anodes or together in case of refined copper, is accomplished in 24 hr. from the time the sample is received by the chemist.

Jan 8, 1913

By H. M. Chance

The Choctaw coal-field is a direct westward extension of the Arkansas coal-field, but its coals are not like Arkansas coals, except in the country immediately adjoining the Arkansas line. From the base of the coal-bearing rocks up to the top of the coalmeasures, I find a total thickness of at least 8500 feet. This great mass of coal-bearing rocks consists of an alternation of slates, shales, sandstones and coal-beds, with their accompanying under-beds of fire-clay. Only one small bed of limestone was observed. This occurs near the middle of the series; it is about eighteen inches thick, and quite arenaceous. The formation is naturally subdivided by seven or eight thick beds of sandstone, varying from 50 to 200 feet in thickness, the outcropping edges of which form a series of more or less bold " hogback " ridges, the interbedded shales and slate forming the intervening valleys. The base of the coal-series is a massive sandstone, ranging from 100 to 200 feet or more in thickness, lying immediately beneath the Grady coal-bed, which is the lowest known coal. In the district embraced between. the Missouri, Kansas and Texas railroad and the Arkansas State line, this sand-rock usually forms a bold semi-mountainous ridge. This is the ridge through which the St. Louis and San Francisco railroad passes at Bryan station, where the Grady coal-bed is opened and worked, from which point it can be traced westward without difficulty, passing about three miles north of Le Flor on the same railroad, thence west to the " Little Narrows " (which is merely a gap in the ridge), 'and beyond to a point two miles west of the Thompson-McKinney place, where it swings abruptly north for a mile or more, only to resume immediately its westward course, forming for some miles the northern boundary of the valley known as the " Boiling-Springs Prairie," beyond which it trends somewhat

Jan 1, 1890

By D. W. Lillie

It has been demonstrated that considerable bend ductility exists in bulk specimens of polycrystalline high-purity silicon. The possibility of hot-forming at 1200°C is suggested. EXCELLENT corrosion resistance in many media and low cross section for absorption of thermal neutrons (0.13 barn) would make silicon of interest to nuclear engineers were it not for extreme brittle-ness and the difficulty of fabrication by any reasonable means. The use of silicon for structural purposes also has been considered in view of its light weight and oxidation resistance. Johnson and Han-sen' have investigated the properties of silicon-base alloys and concluded that there was no way of making pure silicon or silicon-rich alloys ductile at room temperature. In view of reports of appreciable ductility in germanium single crystals above 550°C'." and some plastic deformation in single-crystal silicon above 900oC,' the present investigation was undertaken to define more precisely the limits of high-temperature ductility in pure silicon. After this investigation was begun torsion ductility in both germanium and silicon was reported by Greiner." Through the courtesy of F. H. Horn, a small bar of cast extra high-purity silicon was obtained and small bend specimens were made from it by careful machining and grinding. All of the reported tests results were obtained from samples from this bar (bar No. 1) and one other of similar source (bar No. 2). No complete analysis was obtained but, based on analysis of similar semi-conductor grade material, metallic impurities were under 0.01 pct total. Vacuum-fusion analysis for oxygen showed a value of 0.0018 2 0.0003 pct for the first bar tested and metallographic analysis showed no evidence of a second phase. Bend tests were carried out on an Instron tensile machine using a bend fixture with a 1 -in. span loaded at the center. Supporting and loading bars were 0.250 in. round and the load was applied by downward motion of the pulling crosshead of the machine. Specimen thickness and width were approximately 0.10 in. and % in. respectively. Loading rate was controlled by holding crosshead motion constant at 0.02 ipm. In some cases a smaller specimen was used on a 5/8-in. span with a 0.129-in.-diam loading bar. The entire bend fixture was surrounded by a hinged furnace and all heating was done in air atmosphere. Temperature measurement was made with thermocouples fastened directly to the bend fixture within less than 1 in. from the specimen. Autographic stress-strain curves were recorded during each test, and breaking load, total deflection, and plastic strain could be obtained from these curves. Stress was calculated from the beam formula S = 3PL/2bh2, where P is the load in pounds, L the span in inches, b the specimen width in inches, and h the specimen thickness in inches. This formula is strictly correct only in the elastic range but has been used to calculate a nominal stress for convenience in the plastic range. The stress given is the maximum stress in the specimen. Results The results of the complete series of tests are shown in Table I. The first group of tests (specimens Nos. 1-6) showed the beginning of plastic flow at a test temperature of 900°C, so two additional tests (Nos. 8 and 9) were made at 950°C on small-size specimens from bar No. 2. Specimen No. 8 was tested in the as-machined condition, and No. 9 was heat-treated in hydrogen at 1300°C for 2 hr, cooled to 1200°C and held 1 hr, cooled to 1000°C and held 1 hr, cooled to 900°C and held 1 hr, and finally cooled to a low temperature before removal from the hydrogen. It is apparent that the heat-treatment had a significant effect on yield strength and ductility. In addition, the magnitude of the yield point was conslderably reduced in the heat-treated specimen as is shown m Fig. 1 by tracings of the stress-strain curves. After obtaining a furnace capable of reaching higher temperatures specimens Nos. 10 to 13 were tested at 1100 and 1200°C. Strain rate was increased by up to a factor of 10 to see whether the ductility observed was excessively strain sensitive. Specimen NO. 10, strained at 0.02 ipm and 1100oC, was still bending at a deflection of 0.322 in. when the load rate was increased to 0.2 ipm, resulting in immediate

Jan 1, 1959

By Richard H. Siller, Rex B. McLellan

A model for interstitial solid solutions has been considered in which a repulsive Potential exists between interstitial atoms in the solvent lattice. It has been shown that this model is consistent with the thermodynamic Properties of certain interstitial solid solutions. The model is then applied to the calculation of the variation of the diffusivity of carbon in au-tenite with composition. Although the energy levels at the saddle point, and thus the absolute values of dif-fusivity, cannot be calculated, it is shown that by taking the repulsive interactions between the diffusing atoms into account the functional form of the dependence of diffusivity on solute concentration can be derived. ThE composition dependence of the diffusivity, D, of carbon in austenite at a given temperature is well-known.'-3 smith3 tried to reconcile the observed composition dependence of D at 1000°C with the previously observed4 composition dependence of carbon activity using equations for D derived by arken5 and Fisher, Hollomon, and Turnbull,6 but was unsuccessful. In this paper we shall modify the approach of Fisher et al. by considering the "blocking" model7 for interstitial solid solutions, based on concept due to Speiser and Spretnak,' in which a repulsive potential exists between interstitial solute atoms in the solvent lattice, causing a certain number of interstitial sites to be "blocked" from occupancy by further solute atoms. We shall thus be able to describe the intimate relationship between the composition dependence of carbon diffusivity, a kinetic phenomenon, and the composition dependence of carbon activity in austenite. THEORY Consider for convenience one-dimensional interstitial diffusion in an fcc lattice in the [loo] direction. Fig. 1. Assume that solute atoms occupy octahedral sites only.7,9'10 These octahedral sites are located on {lOO} planes a/2Å apart. A solute atom, A, occupying an octahedral site on a {100 } plane denoted by 2, has twelve nearest-neighbor octahedral sites: four on plane 1, four on plane 2, and four on plane 3. Diffusion occurs when there is a net flux of solute atoms, through an imaginary plane shown with dashed lines, from plane 2 to plane 3. Fisher et al6. use the concept of activated complexes, as given in the theory of absolute reaction rates." They show that the number of solute atoms per cubic centimeter per second which pc — Fig. 1-Diagram showing the arrangement of octahedral sites (x) in the fcc lattice. pass in the direction of diffusion from activated to new interstitial position is: ?where C is the concentration of the solute in atoms per cubic centimeter, l/m + is the fraction of new interstitial positions corresponding to motion in the forward diffusion direction (transmission coefficient), ?F* is the free-energy difference between the activated complex and the reactants when each is in its standard state at the temperature of the reaction (independent of temperature and composition in the case of carbon in austenite), y is the activity coefficient of the solute species, and, finally, ym is the activity coefficient of the activated complex (assumed constant). The flux of atoms moving in the forward direction through an area of 1 sq cm perpendicular to the direction of diffusion is therefore: m+ Ym l ' atoms per second where is the distance between planes. The blocking model states that a nearest-neighbor octahedral site of a given solute atom has a probability, f, of being inaccessible to other solute atoms. The number of available sites for diffusion on a given plane will, therefore, depend on f, which is constant, and Nu, the number of solute atoms on that plane. The effect is to have more available sites in the diffusion direction, thereby increasing the net flux of solute atoms. This is reflected in the transmission coefficient, l/m. To calculate the transmission coefficient for solute

Jan 1, 1970

By M. P. Tixier, A. Poupon, M. E. Loy

Simple qualitative methods are explained for identifying those shaly sands in a well that are most likely to contain oil. A need for more precise measurement of the variables that enter shaly sand analysis is indicated. Field examples are given to illustrate the methods. A theoretical discussion of the quantitative interpretation of shaly sands is given as a basis for discussion and as a guide for the future. While not generally capable of practical application at the present time because of the lack of sufficient accuracy of the electric log data, these methods may become more feasible in the future as the result of the improved logging methods now being introduced. INTRODUCTION Experience has shown that for porous formations containing only a negligible amount of clayey material, reliable information on the fluid saturation and porosity of the reservoir rocks can usually be derived from the electrical logs. The interpretation is based on empirical formulae relating the true resistivity of a porous formation to its lithologic character, to the resistivity of the interstitial water, and to the proportions of water and hydrocarbons in the pores.' If the resistivity of the interstitial water is not known, its approximate value can be derived from the SP curve.2,3 The porosity can usually be determined to a good approximation from a MicroLog, or a MicroLaterolog.4,5 When the reservoir rocks contain an appreciable percentage of clayey material, an additional factor is introduced into the analysis. In a clean formation, the matrix is an electrical insulator, so that the ability of the formation to conduct current is due only to the conductivity of the electrolytes in the pores; in a shaly formation, the shale constitutes a part of the rock matrix able to conduct current, and influences the resistivity of the formation. On the other hand, the spontaneous emf's and the circulation of the SP currents are also responsive to the presence of the shaly material. All other factors being the same, the deflection of the SP curve opposite a shaly permeable formation is smaller than the deflection which would be observed if the formation were clean. The effects of the presence of shale on the resistivity and on the SP curves in a shaly formation are functions of the amount, of the specific resistivity, and of the geometrical distribution of the shaly material within the formation. The presence of shale therefore constitutes an important complication in electrical log interpretation. It is easy to realize, for example, that the presence of a large amount of clayey material in a sand may have such a predominant effect that the resistivity of the sand will not change very much, whether the pores are entirely filled with connate water, or contain a high saturation of hydrocarbons. Important research projects have been undertaken to investigate the influence of shales and to find a way to allow for this influence in the interpretation of a log. The problem of the SP in shaly sands was analyzed mathematically by H. G. Doll"' for the case of sands with shale laminations. Formulae expressing the resistivity of shaly formations were proposed by Patnode and Wyllie8 and de Witte.9 Other quite interesting theoretical and experimental results have been published by various authors.l0,ll,12,l3,14 The purpose of the present paper is to discuss an approach to electrical log interpretation in shaly sands. This approach is based partly on some of the theoretical and experimental data available in the literature and partly on observations made on actual field logs. Comparatively simple methods for qualitative and semi-quantitative analysis are described. These methods depend principally upon information provided by the electrical logs.

Jan 1, 1955

By John F. Elliott, John R. Rawling

The rate of reduction of silica to silicon by carbon at 1550° to 1700°C in iron blast-furnace type slag-metal systems has been investigated. In the tower portion of the temperature range oxygen transport in the metal boundary layer at the slag-tal interface is probably rate limiting. A second step, which apparently involves a chemical process in the slag at the slag-metal interface, appears to be rate limiting when the oxygen-transport limitation is avoided. Above 1650°C rate control of the reduction by carbon probably is mixed between the two steps. INVESTIGATIONS1.2 into the equilibrium distribution of silicon between graphite-saturated slags and metals typical of iron blast-furnace practice show that, under the experimental conditions specified, the reduction of silica to silicon is relatively slow compared with the rates of other slag-metal reactions under similar conditions. For this reason, the reduction of silica in blast-furnace slag-metal systems was considered to be an interesting subject for further study. Investigations of the kinetics of the reaction3-5 suggest that several possible steps may be rate controlling, and that the rate-controlling step depends not only on the physical state of the systems but also on the configuration of the apparatus. The main objects of the investigation reported here were to sug- gest plausible reaction paths for the reduction of silica under the experimental conditions chosen and to determine the step or steps which control the rate of reduction of silica. EXPERIMENTAL Two types of experiments involving the reduction of silica from the slag were carried out. In the first, the only reducing agent present was carbon (graphite), for which the over-all reaction is (SiO2) +2C(gr) —Si + 2Co(g) [l] The second type was a graphite-saturated ferro-silicon-iron concentration cell. In it silica in the slag could be reduced either by carbon according to Eq. [I], or by a reaction of electrochemical nature in which silicon was oxidized at the ferrosilicon-slag interface and silica was reduced at the slag-iron interface without the formation of CO. The two types of experiment are described below. Reduction of Silica with Carbon as the Only Available Reducing Agent. The reduction of silica was accomplished by allowing a liquid lime-alumina-silica slag and graphite-saturated iron to react in an induction-heated graphite crucible. The crucible was 2.25 in. diameter and 5 in. deep; it was fitted with a graphite stirrer which penetrated through the slag and into the metal, Fig. 1. The slag and metal charges weighed 350 g each. Pure carbon monoxide at a pressure of 1 atm was maintained above the melt by passing the purified gas through the crucible at a rate of 0.5 liter per min. The gas did not stir either the slag or metal. Temperature measurements were made by sighting an optical pyrometer down the hollow stirrer rod into a 1/4-in. hole drilled in the stirrer blade. The crucible temperature was maintained within *15"C of the required value by manual control of the power supply to the

Jan 1, 1965

By C. R. Dodson, D. Goodwill, E. H. Mayer

The paper summarizes the historical background of the pressure-volume-temperature analyses of reservoir fluids, the errors involved in both the sampling and testing of reservoir fluids, the type of information required of a PVT determination, and the field conditions that limit the application of any one analysis. Particular emphasis is placed on the necessity for approximating as closely as possible the liberation sequence occurring in the producing formation, flow string, and surface separators. A combined differential and flash or "composite" liberation is suggested as the best means of approximating this liberation sequence. HISTORICAL BACKGROUND Petroleum reservoir engineering commonly is considered to be one of the newest fields of petroleum science, yet much work of a theoretical and intuitive nature was done many years before the modern techniques of reservoir analyses were developed. The period 1910-1924 saw considerable work in the field of reservoir behavior done by the U. S. Bureau of Mines. This work:.' although entirely theoretical, pointed out the importance of gas in the recovery of oil from the reservoir. The statement by J. 0. Lewis that 20 per cent or less of the oil originally in place in a pool was recovered from the ground under uncurtailed production conditions caused some operators to re-examine and modify their production methods. However, though these works showed methods of production that have subsequently resulted in greater oil recoveries, they in general went unnoticed, even though there was a fear that the nation's petroleum resources were being exhausted. The period 1924-1933 saw the industry take considerably more interest in reservoir behavior because of an unfounded fear of its inability to replace oil reserves, the possibility of government regulation, and the energy of one man, Henry L. Doherty. Doherty aroused heated discussions in the industry concerning conservation. To prove or disprove his theories the first experimental work on the reservoir behavior of petroleum was undertaken. The papers of Dow and Calkin,' Beecher and Parkhurst," and Mills and Heitheckere are classics although their experimental procedures were crude. These papers proved that the properties of petroleum in the reservoir are quite dissimilar to the properties measured at the well head. Gas dissolved in the oil phase was recognized as having considerable importance as had been predicted by the earlier theorists. Slightly later Miller and his co-workers assembled the first text correlating all the known data on the reservoir behavior of petroleum and used, these data to show the economic value of conservation. Quantitative application of pressure-volume-temperature analyses of reservoir fluids was given in the paper of Coleman, Wilde, and Moore"; this work showed that with sufficient laboratory and production data prediction of reservoir behavior was possible. The refined sampling and labora-

Jan 1, 1953

By J. B. Bassett, E. S. Rowland

The experimental work reported herein firas inspired by the publication of a paper by Grange and stewart, in which it was suggested that at low chromium contents the effect of this element on the Ma point was greater than at higher chromium contents, It was argued that, if a small increase of chromium in solution in austenite caused a sharp lowering of the M, point, it might lead to an explanation of occasional unsolved stress cracking of SAE 52100 during heat treatment. Commercial hardening is carried out at temperatures of incomplete solution, leaving carbides available to enrich the austenite during any inadvertent increase in temperature, such enrichment of the austenite in chromium content would lower the M, point nearer room temperature where cracking is more likely to occur. According, it was decided to investigate the effect of chromium, in quantities between o and 2 pet, on the M, point of commercial steels. Fig I summarizes the data available on chromium steels. For purposes of comparison, the M, temperature values were corrected by means of the Grange and Stewart formulas to (I) Hypoeutectoid compositions: 0.50 pct carbon and 0.80 pct manganese (z) Hsereutectoid compos-sition': 1." pet carbon and O.35 pct manganese. Only the steels having compositions reasonably close to these corrected values were included, because large adjustments inevitably introduce increased error such as are experienced in using the formula. The straight lines of Fig I were drawn by the authors. These data obviously do not settle the question Of the effect Of chromium On the Md Oint, particularly at low chromium contents. While it is fairly well established that chromium causes the M, to be lowered when present in quantities of I pet Or more, Grange and Stewart1 have suggested that in small amounts (less than 1 pet) it is more effective in lowering the Ma point, while Klier and Troiano2 have suggested that in small amounts it is less effective in lowering the Ma point. Payson and Savage3 concur with Klier and Troiano and further suggest that the effect is not linear at these concentrations. Rose and Fischer4 report that small amounts of chromium actually raise the Ma point of a 0.20 carbon steel. Material Two series of 35 Ib induction heats were melted for this work, the analyses of which are given in Table I. One series was aimed at 0.50 pct carbon and 0.80 pct manganese with chromium additions in 0,25 pet increments from o to 1.5 pct with a single heat at 2.0 pct Cr. This series was considered necessary because the commercial heat treatment of SAE 52100 does not generally introduce more than about 0.60 pct carbon in solution in the austenite. The high

Jan 1, 1949

By Walter W. R. May

FOR more than 25 years a few business men who represent virile private enterprise in the Pacific Northwest have been trying to awaken the community to the potential benefits of an open Columbia River. No threat of government com- petition then hung over the industry, which was adjusted to state regulation. Numerous sites were engineered and the findings were laid before the operators of heavy industry in the East, Middle West, and South -even of Europe. These engineering data became, if not the basis, the inspiration upon which the U. S. Army Engineers eventually were to "build the Columbia River Bible" - their great document known as House Document 103, the report on the Columbia River and minor tributaries.

Jan 1, 1940

By W. W. Vaughn, R. H. Barnett, E. E. Wilson

Soon after the search for uranium ores on the Colorado Plateau began in earnest, thousands of feet of drill core ranging from 1 1/8 to 2 1/8 in. diam became available for study. Although significant advances had been made in the technique of quantitative gamma-ray borehole logging, instrumentation was in the development stage, and complete reliance could not be placed on gamma-ray logs alone to interpret quantitatively the meaning of radioactivity in a drillhole. A method that would be faster than chemical analysis and still give reproducible and reliable results for various drill core sizes was desirable to provide additional information on the enormous footage of drill core being accumulated. A solid phosphor scintillation drill core scanner was designed and constructed. Basically the instrument was developed to measure radiation from a drill core which would not be clearly recorded by a gamma-ray logger using a Geiger tube as the sensitive element. Such data would be beneficial in constructing isorad maps to delineate ore-bearing zones. A calibration in the range 0.01 to 0.1 pct eU.,O, was provided; above 0.1 pct eU3O8 gamma-ray logs were available and were being used to calculate grade and tonnage of ore reserves. The core scanner, however, has been used to estimate equivalent uranium content of ore-grade materials containing as much as 2.2 pct eU3O8 with an accuracy of ± 10 pct, the sample being in the form of a BX drill core. Actually, an apparent calibration of eU3O8 vs counts per unit time is a straight line with a slope that is a function of the sensitive element and the geometry of the counting assembly. A true calibration that will show the expected departure from a straight line is due principally to the random nature of the pulse from a radiation source and the nonlinearity of the electron circuitry. Design and Construction: Three methods of detecting radioactivity were considered and applied in developing the core scanner now in use: 1) the Geiger tube, 2) liquid scintillation phosphors, and 3) solid scintillation phosphors. The desired sensitivity and long-term drift characteristics needed for this operation could be attained only by using solid scintillation phosphors. All three methods are discussed. Before scintillation counters were common, nine beta-gamma sensitive Geiger tubes 7/8 in. diam by 12 in. long were used, arranged to surround the drill core with tube axes parallel to the axis of the core. This arrangement of Geiger tubes was en- closed in a lead shield 1 in. thick, and provision was made to slide a 6-ft length of drill core manually into the counting chamber, one foot at a time. A count for each segment was taken with a scaler while the core remained stationary. The equivalent uranium content of the different sections of drill core could then be estimated with the aid of a calibration curve of counts per unit time vs percent equivalent uranium (eU). In rare cases the effects of the radioactivity concentrated in small areas within the core introduced errors in the readings made with the Geiger tube arrangement owing to the geometry of the measurement. The variability of counting rate due to a localized concentration of radioactivity in a spot in the wall of a drill core is illustrated in Fig. 1. This effect and the inherent low efficiency of the Geiger tube were considered major disadvantages of this counting arrangement. When liquid scintillation phosphors became available the core scanner in Fig. 2 was constructed to make a more accurate measurement of the equivalent uranium content of a sample. This instrument contains about 4 liters of liquid phosphor in a stainless steel coaxial cylinder 1 ft long, with inner and outer walls 0.060 in. and 0.125 in. thick, respectively. Four end-window type photomulti-plier tube with cathodes of 2 in. diam, immersed in the solution at right angles to the axis of the core, were used to observe light flashes in the phosphor. The liquid phosphor offered equal sensitivity to radiation originating at any point in the enclosure and represented geometrically the optimum in design. However, providing a semi-permanent leak-proof seal between the glass envelope of the phototube and the metal walls of the container proved to be a serious problem in constructing the equipment. The most effective seals were especially machined O-rings from sections of large tygon tubing. The tygon took a permanent set owing to cold flow characteristics and in most cases sealed completely. The light absorption characteristics of the liquid phosphor changed gradually with time, and after one month the counting rate had decreased to half the original value. The most sensitive liquid phosphor tested proved to be a solution containing 4 g of 2.5-diphenyloxazole and 0.01 g of 2-(1-naphthy1)-5-phenyloxazole per liter of toluene. With fresh solution in the chamber and with all photomultiplier tubes operating in parallel, the counting rate contributed by any one of the four photomultiplier tubes was about 85 pct of the counting rate from a single tube operated individually. From these observations it was concluded that owing to coincident loss and light attenuation within the liquid phosphor, the apparent sensitivity could not have been materially increased by additional phototubes. However, this approach to core

Jan 1, 1960

By P. H. Brace, N. A. Ziegler

THE study of the relations between gases and metals is one of perennial interest to all who are connected with the production of high-grade metallurgical products. The data reported here are the outcome of work of which the object is to determine the effects of dissolved gases upon the properties of metals and to gain a more detailed knowledge of the reactions between gases and molten metals, particularly iron, under definitely controlled conditions. We have attempted to reduce our margin of error by dealing with relatively large quantities of metal, from 4 to 13 lb. (2 to 6 kg.), and keeping the ratio of refractories to metal as small as practicable. The ingots produced are large enough to provide adequate material for making determinations of magnetic and other physical properties. In choosing the bell-jar type of furnace we were influenced by the results of considerable experimentation along the same general line which indicated that, for the scale on which we were to work, it was important to have the furnace structure independent of the vacuum enclosure. The use of a bell-jar surrounding the entire furnace accomplishes this and also gives great freedom of observation during operation and ready accessibility for the replacements which are necessary after each run. Our choice of analytical method was made in the light of the results secured by H. M. Ryder, who used a method similar in principle for the analysis of very small quantities of gas extracted from strips of metal heated electrically in high vacuum. We have presented some selected preliminary experimental data as being illustrative of the quantity and nature of the gases which occur in iron of different origins, but do not urge any hypothesis at this time. THE FURNACE Our furnace may be described as "a high-frequency induction furnace of the bell-jar type." It is similar in a general way to that described by Cain and Peterson' though we have introduced certain refinements of

Jan 1, 1928

By Juptner von Jonstorff

A discussion of the paper by Messrs. Jüptner von Jonstorff, Blair, Dillner and Stead, read by title at the Lake Superior meeting, but presented first at the New York meeting of the Iron and Steel Institute (October, 1904), and here published under a mutual agreement between the two Institutes. Correspondence. MR. R. HAMILTON (Glengarnock) wrote to say that it was known for many years, that unless certain precautions were taken in dissolving the sample, there was a liability to obtain a solution from which the ammonium-molybdate solution would not precipitate the whole of the phosphorus. In 1877 Blair and Finkiner independently attributed this interference to the presence of carbonaceous matter in the solution, derived from the action of acids on the combined carbon of the metal, and they directed that the solution should be prepared in such a manner as to destroy these carbonaceous compounds. This was practically effected by evaporating the acid solution to dryness and roasting the residue. Adolf Tamm, in 1884, accentuated the same view. There are methods founded on the above-mentioned observations which leave nothing to be desired in point of accuracy, but the evaporation to dryness with subsequent roasting and re-solution consumes much time, besides the minor inconvenience caused by large amounts of acid fumes. In 1888 P. W. Shinier suggested that the incomplete precipitation of phosphorus was due to incomplete oxidation of -.the phosphorus, and proposed to render all the phosphorus precipitable by oxidizing the solution with potassium permanganate, etc. Experiments were made to test the accuracy of this view (details will be found in the Journal of the Society of Chemical Industry, vol. x., p. 904), and the results obtained seem to-prove that it is the correct one. It was first proved that carbonaceous matter in solution did not prevent the precipitation of properly oxidized phosphorus

Mar 1, 1905

By Robert L. Grayson, Y. J. Wang, R. Mike Mishra

Prediction of ventilation needs in long range mining projections requires serious consideration when formulating those projections. Predicting the behavior of the ventilation system of an old, complex mine poses an especially provocative problem. Air-flow around and through mined-out areas via bleeder systems, leakage flows through stoppings or other air control devices, and the use of multiple fans all add to the basic complexity of a ventilation system and make predictions of ventilation changes very difficult. Fortunately, the task of making ventilation decisions can be greatly assisted by ventilation surveying and computer simulation. The Nemacolin Mine of Jones and Laughlin Steel Corporation, located in Southwestern Pennsylvania, is one such old mine which used the computerized approach successfully. A mine-wide pressure-quantity survey was used to obtain realistic values for airway resistance factors. These values, together with network topology, formed the basic input for computer simulation. Results from this simulation indicated that air quantities generated at critical airways by the model were generally within a couple of percent of those measured in the actual survey. It was then concluded that the model was acceptable for practical application, and it was used immediately for studying the effects on the ventilation system of changing the blade settings of fans. Additionally, the model was modified to incorporate projected mine development and used to predict future ventilation.

Jan 1, 1982

By Sidney H. Haughton

WHEN the white pioneers of the eighteenth and nineteenth centuries advanced from the coastal settlements of southern Africa into the interior of the subcontinent, they found it inhabited, more or less sparsely, by brown or black peoples mainly of pastoral habits but equipped with a fighting spirit and certain fighting weapons. Some of the tribes were smiths, others were miners and metallurgists; all used fuel, either industrially or domestically. Some of that fuel was wood, some cattle dung, and in some places the natives mined outcrop coal. Coal was first discovered by Europeans in Natal about 1840. After proper deliberation and after allowing due time for a consideration of all the implications, the Natal Government decided in 1881 (40 years after) to import an English expert to investigate and report on the discovery. Things then moved rapidly, and in what to a geologist is the remarkably short space of eight years, Natal collieries were producing at the rate of nearly 30,000 long tons per annum or 100 long tons per working day!

Jan 1, 1945

By AIME AIME

THE accompanying photograph: submitted by C. L. Bransford, assistant district manager of the Republic Steel Corp., in Birmingham. Ala., shows the remains of the old Tannehill blast furnaces, one of the first furnace plants in the South. They were built by Moses Stroup and operated during the Civil War period, when cannon balls were cast there. The record day's run of this furnace plant was said to be 30 tons of iron. The furnaces were fed by a water-wheel-operated bellows and used charcoal, a product of the neighboring forest. They were first owned and operated by the Pioneer Mining & Manufacturing Co., that later became the Republic Iron & Steel Cu., and subsequently the Republic Steel Corp. in that district.

Jan 1, 1936

By R. A. L. Black, J. E. Jennings

The problems of slope stability in open cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the orebody. This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ. A company embarking on open cast mining is faced with two basic questions: 1) will the venture be profitable and 2) can it be carried out with safety? The two questions are obviously interrelated because both depend upon the slope angles adopted for the pit. The cost of open cast mining depends largely upon the stripping ratio, defined as the volume of overburden that must be removed to the volume of ore recovered. The steeper the slope angles, the more favorable the stripping ratio, but the stability of the slopes, and therefore the safety of men and materials in the pit, require that the angles be made relatively flat. Consequently, the design depends upon a compromise: the slopes must be steep enough to result in economical mining and flat enough to ensure safety. Today there is a world trend towards deeper mining by open cast methods. This is mainly due to the higher cost of underground mining and the lower cost of open excavation resulting from the introduction of large modern earth and rock-moving machinery. Deeper open cast mining has led to a very great increase in the volumes of wasted overburden, and much thought is being given to the considerable economic benefits which would result if pit slopes could be made steeper by even one or two degrees. The result has been an increasing interest in research into slope stability problems in the expectation that the application of scientific principles will provide solutions leading both to economies and to more predictable operation of the mines. In at least four places, the U.S., Australia, Western Germany and Southern Africa, comprehensive investigations are at present in progress, and it is the object of this paper to review some of the more important aspects of these programs. RELATION BETWEEN ECONOMY OF OPERATION AND SLOPE ANGLES The main object of any industrial enterprise in a free economy is to make a profit. In mining, where profits must be made from a wasting capital asset, a further definition of the profit motive is imposed, namely that the economic aim should be to maximize the total possible profit. But since profits deferred for a number of years are not as valuable as profits that are immediately available, it is usual to discount deferred profits at some rate of interest which reflects their current or present value in the hands of the investor. Thus, in mining the logical aim can be defined more closely still: to maximize the present value of the total future profits. In commercial terms the present value represents the market value of the operation as a going concern. Many factors enter into the forecast of current and future profits. They include the volume of production, the price of the salable product and the cost of production. Current profits can be estimated with reasonable accuracy by the operating engineers; but it is the task of economists and management to assess future trends in the mineral markets and in the economy as a whole, and together with the engineers, they can then estimate the future cost and profitability of the mining operations. In open cast mining, the rate of ore production once decided on remains a virtually constant factor unless a major change in the capital structure of the mine is made. But one factor over which the operator has a considerable measure of control is the ratio of the volume of ore mined to the volume of waste over-

Jan 1, 1963

By R. E. Somers

Discussion of the paper of R. E. SOMERS, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 101, May, 1915, pp. 957 to 996. A. C. LAWSON, Berkeley, Cal.-One point to which Mr. Graton (in summarizing the paper for us) called attention is that the author had not explained why some copper was fixed in the zone of oxidation. I recollect very well puzzling over that question at Ely, Nev., some years ago. Mr. Sales, in his paper on Butte,1 suggests the explanation. It is clue according to him to the paucity of pyrite in the primary ore. Where there is abundant pyrite sufficient sulphuric acid is formed by oxidation to take all the copper into solution and carry it to lower levels; but where the pyrite is scant so that insufficient sulphuric acid is formed, some of the copper is carbonated and so fixed in the gossan. The hypothesis, or some modification of it, as for example the combination of the sulphuric acid with lime, would appear to explain satisfactorily the fixation of the copper in the gossan as carbonate. I have, however, had no occasion in recent years to study the phenomenon. L. C. GRATON, Cambridge, Mass.-As I remember, the rocks in which the chrysocolla occurs in the Burro Mountains are both silicified and kaolinized. It seems probable that in surroundings deficient in carbon dioxide, complete oxidation of chalcocite may yield chrysocolla up to a maximum of half the copper in the chalcocite; while in rocks, like garnet contact zones and certain easily decomposable porphyries, surface decomposition appears often to yield silica in the necessary form to convert the copper of primary sulphides into chrysocolla immediately and directly upon oxidation.

Jan 12, 1915

By Eckley B. Coxe

The subject of this paper will be treated as briefly as possible under the following heads : I. The latest designs of some of the machinery used at these collieries in the preparation of coal. 11. The means employed for elevating, conveying and transporting the coal and slate in and about the breaker. 111. The means employed for raising the coal from the mines to the top of the breaker. IV. The iron breaker as a structure. V. The preparation of the coal as effected in the iron breaker. A key to the plates and the letters and numbers designating different parts, will be found at the end of the paper. I. Preparing Coal. Anthracite coal as it comes from the mines is not marketable. The "run of mine" cannot, as in the case of bituminous coal, be sold. Anthracite, being very compact and practically free from volatile combustible matter, burns only at the surface, and it is, therefore, deemed important to have the lumps as nearly of a uniform size as possible, so that between them a large amount of surface will remain exposed to the action of the air without checking the draught too much, or allowing enough air to pass to cool the coal below the ignition-point, In other words, if the pieces of coal of the size of a chestnut and smaller are mixed with lumps of the size of an egg they fill the air-passages and prevent a free draught. It has long been recognized, therefore, that one of the most important points in preparation is to have a uniform sizing, and also to make as large a number of different sizes as can be produced without too

Jan 1, 1891