Search Documents

By D. Turnbull, H. N. Treaftis

Precipitation of tin from Pb-Sn alloys (lead-rich) occurs by the nucleation and growth of hemispherical cells which consist of tin lomelloe interspersed in the depleted solid solution. Nucleation and growth of these cells and the tin interlamellar spacing at various compositions and temperatures have been investigated. The interlamellar spacing increases approximately as the reciprocal of the logarithm of the supersaturation ratio. For constant initial tin concentration the concentration of cell nuclei increases with decreasing temperature to a limiting temperature-independent value. The kinetic results support the view that the cell growth rote is governed by the diffusion of tin along the cell boundary. In the main, the results confirm the authors' earlier deductions, drawn from resistometric and calorimetric data, about the precipitation mechonism. IT has been shown1, 2 that tin (ß) precipitates from lead-rich (a) PbSn solutions by the nucleation and growth of cells (cellular or discontinuous precipitation). These cells consist of tin lamellae, with a spacing 1, interspersed in a depleted a solution. Reorientation of a also accompanies cell growth. The kinetics of cellular precipitation of tin from lead have been measured by resistometric2, 3 and ca1orimetric1, 3 techniques. The time-transformation isotherms (t equals time; x, volume fraction of specimen transformed) of the initial rapid precipitation, which drains about 60 pet of the tin from solution, have been described by a kinetic law having the form x = 1 —exp (—bt n) [I] where n usually has the value 3.0. It was shown" that this law and the other kinetic facts can be explained satisfactorily if it is assumed that the cells grow at a constant rate and that all the cells nucleate in a time negligible in comparison with the period of cell growth before impingement. Thus, for hemispherical cells b = (2/3)pNG3 [21 where G is the rate of cell growth in cm per sec, and N is the number of cell nuclei per unit volume. The rapid rate of cell growth at low temperatures can be accounted for"' if it is assumed that the dissolved tin drains to the lamellae edges by diffusion along the sweeping cell boundary rather than by diffusion through the a crystal (volume diffusion). For cell growth governed by cell boundary diffusion it was shown, approximately G=2(X° - X° / X° ) DBA / l2 where A equals the thickness of the cell boundary; D R, the coefficient of diffusion of tin atoms within the boundary; and X° and X, are the atom fractions of tin in the supersaturated and saturated solutions, respectively. Zener8 had already shown that, where

Jan 1, 1959

By G. D. Rieck, M. M. P. Janssen

Chemical diffusion coefficients and heats of activation for diffusion in the NizAh fy), NiAl (6), and Ni3A1 (E) intermetallic phases and the solid solution of aluminum in nickel (( phase) were calculated from layer growth experiments. No finite diffusion coefficient for the NiAl3 ((3) inter metallic phase could be calculated. The values of the diffusion coefficients are dependent both on the method of calculation and the type of diffusion couple. The heat of activation for diffusion in the y phase was found to be 47 kcal per mole in the temperature range oj 428" to 610°C. Heats of activation of 41, 12, and 48 kcal per mole were found for diffusion in the 6, E, and ( phases, respectively , in the temperature range of 655" to 1000°C. Experiments with markers in the diffusion zone demonstrate a very pronounced Kirkendall effect. It appears that only aluminum atoms take an active part in the diffusion process during the formation of the 0 and y phases at temperatures of about 600°C. During the formation of the 6, E, and < phases at higher temperatures only nickel atoms are moving. It is suggested that the great stability of the intermetallic compounds in the Ni-A1 system governs the Kirkendall effect. SOME factors controlling layer growth during inter-diffusion in the Ni-A1 system (phase diagram, see Fig. 1) were studied by Castleman and Seig1e.l&apos;~ They found the NiA1, ((3) and NiAl3 (y) intermetallic compounds to appear in the diffusion zone of Ni-A1 couples at annealing temperatures of 400" to 625°C; the NiAl (6) and Ni3A1 (E) intermetallic compounds appeared in y-Ni couples at annealing temperatures of 800" to 1050°C. These authors carefully examined metallographically Ni-A1 couples after 340 hr annealing at 600°C. Besides the (3 and y phases they found very thin layers of the 6 and E phases. ~n~erman~ and Castleman and Froot4 observed a much more rapid growth of the 5 and E phases at 600°C in Ni-A1 couples in case a crack was present at the /3-A1 interface. Numerous layer thickness measurements carried out by Castleman and Seigle on the y phase prove that the layer growth of this phase obeys the parabolic law after a certain transient period. From this they concluded that the layer growth of the y phase is controlled by volume diffusion. The growth of the 13, 6, and E phases appeared to be volume-diffusion-controlled also. The authors estimated that at 600°C and at atmospheric pressure Dp was 1.8 x lo-"ll sq cm per sec, D, 9.1 x 10" ™ sq cm per sec, Qp 27 kcal per mole, and Qy 31 kcal per mole. The present work was carried out to obtain more quantitative data about the kinetics of growth of the phases of the Ni-A1 system and the reactions that occur during the formation of these phases. Because in this system the diffusion process results in the formation of several distinct intermetallic compounds, the current term reaction diffusion is used in the title of this paper. In order to obtain layers of the fl phase compound of uniform thickness, a new technique for preparing diffusion couples was developed. The kinetics of growth of the y phase in 6-Al, E-Al, and Ni-A1 diffusion couples was studied at different temperatures. The kinetics of growth of the 6, c, and ( phases in Ni-y, Ni-6, and Ni-c diffusion couples was also studied at different temperatures. The calculation of the diffusion coefficients Dp and Dy by Castleman and Seigle are critically considered in this paper; by means of a revised method of calculation more reliable val-ues of , and Dg were found. These values are in good agreement with the values of the diffusion coefficients obtained by the method of Boltzmann-Matano. From the temperature dependence of the diffusion coefficients the heats of activation for diffusion were calculated by means of an Arrhenius-type equation. The investigation of the Kirkendall effect has been used to obtain information about the ratio of the intrinsic diffusion coefficients of the separate atoms5 and the mechanism of diffusion. Moreover porosity as a result of a distinct Kirkendall effect would be of practical importance in connection with the bonding of diffusion coatings. The analyses of the diffusion couples were carried out by metallographic methods. The values of the concentrations at the phase boundaries and the concentration profile in each of the phases, which are needed for the calculation of diffusion coefficients, were obtained by electron-pro be X-ray microanalysis. EXPERIMENTAL PROCEDURE A) Materials for Diffusion Couples. The intermetallic compounds 6 (50 at. pct Ni) and E (74 at. pct Ni) were prepared from the pure metals by high-frequency induction melting in argon atmosphere. Use was made of aluminum wire (99.99 wt pct Al) and nickel sheet (99.95 wt pct Ni). The 6 and E phase melts and the nickel shiet (thickness 0.1 and 0.5 mm) used for preparing diffusion couples were annealed for 64 hr at 1200°~ for homogenization and grain coarsening (final crystal size 1 to 3 mm). composition and homogeneity of the intermetallic compounds were checked by mi-crohardness measurements and X-ray diffraction. From the 6 and E phase melts discs of 0.5 mm thickness were prepared by means of a water-cooled rotat-

Jan 1, 1968

By O. W. Simmons, L. W. Eastwood, C. M. Craighead

Binary alloys of titanium with silver, lead, tin, nickel, copper, beryllium, boron, silicon, chromium, molybdenum, manganese, vanadium, iron, and cobalt were studied. One-half-pound ingots of the alloys were prepared in an arc furnace, employing a water-cooled copper crucible, an argon atmosphere, and a water-cooled tungsten electrode. The half-pound ingots were fabricated by forging at 1700°F in air to 1/4-in. slab, followed by hot rolling at 1450°F to 0.060-in. sheet. Tensile properties, minimum bend radii, hardnesses, response to heat treatment and aging treatment, and phase relationships were determined for these alloys. EARLY in 1947, as one phase of the evaluation of materials for Air Force Project RAND, Battelle successfully arc melted Bureau of Mines titanium and obtained a few basic properties of unalloyed titanium and several titanium-base alloys. The low density, excellent resistance to corrosion, and high tensile properties of these materials stimulated a great deal of interest among metallurgists and designers seeking better materials of construction. As a result of this early work, Battelle, under contract with the Air Materiel Command, Wright-Patterson Air Force Base, has continued extensive studies of titanium alloys. The result of the first year&apos;s work is described in three papers. The present one deals with binary alloys, the second with ternary alloys, and the third paper with quaternary alloys. Melting Method The arc furnace for melting titanium and other refractory metals was developed at Battelle Institute under Air Force Project RAND. During the present work, considerable improvement has been made in the design and operation of this furnace for making small ingots of titanium and titanium alloys. The improved furnace design is illustrated by fig. 1, which shows a cross-sectional view with the dimensions of various parts and their relationship to one another. The essential features of the furnace are the inert argon atmosphere, the water-cooled copper crucible, and the water-cooled tungsten elec- trode. The melting crucible is formed by spinning 0.064-in. annealed copper sheet. A groove for an O-ring seal is spun into the flange of the crucible. A fiber gasket between the crucible flange and the water-cooled brass cover provides electrical insulation. The brass cover is fitted with a sight glass, an opening for the water-cooled electrode, and a tube through which the material is charged. Direct current is used for melting, with the positive electrical terminal connected to the water jacket and the negative terminal to the electrode. A typical heat is made in the new furnace as follows: Approximately, 0.20 lb of titanium under 2 mesh per in. and the alloy addition, if any is to be used, are placed in the bottom of the crucible. The cover is clamped on the crucible so that the O-rings make a tight seal. The remainder of the charge is placed in a glass bottle, and this is connected by a rubber hose to the charging tube of the furnace. The crucible and the charge are evacuated with a mechanical pump to a pressure below 50 mm of mercury, or less if desired, and held at this reduced pressure for 5 min. Hot water is circulated through the jacket during the evacuation period to assist in outgassing the crucible. Following the evacuation, tank argon of 99.92+ pct purity is flushed through the crucible for 5 min and then adjusted to give a positive pressure of 1 to 2 psi. During subsequent operation, an argon pressure regulator introduces only enough argon to compensate for the small leakage which occurs through a mercury trap. Re-evacuation and reflushing the melting chamber with argon produced a negligible reduction in contamination. Two 550-amp generators, connected in parallel, constitute the power source. Normally, about 800 amp are used for melting alloys which are not extremely refractory. The generators are set for 90 v open circuit and 200 amp. The arc is struck and the electrode is withdrawn to produce an arc of 23 to 26 v. This voltage is maintained while the electrode tip is moved slowly around a circle 1 in. smaller than the diameter of the ingot. The current

Jan 1, 1951

By S. Korman, S. B. Tuwiner

THE purpose of this study is to investigate the effect of agitation upon the flotation of chal-cocite. It is believed that the concentration of collector which is required to produce a water-repellent surface upon the mineral is determined among other things by the rate of collector diffusion through an impeding film of more or less stagnant fluid. Its thickness depends upon the intensity of agitation. In the first part of this study a method is developed for determining the thickness of the fluid film upon a polished surface of synthetic chalcocite. The film thickness is then determined as precisely as possible under three readily reproducible condi-tions of agitation intensity. These determinations serve as a quantitative evaluation of agitation. In Part 2 it is demonstrated that in solutions of lime at PH 10.5 and in the absence of air or dissolved oxygen the concentration of collector required to develop water-repellency upon the surface in any given time is a function of the fluid film thickness, and that after about 10 min the relation becomes linear. This points to the possibility that the collector ions may be involved in a diffusional process through the fluid film. In Part 3 it is shown that where air is present more collector is required to produce water-repellency than for the case in which air is excluded. Next, it is shown that for the latter case the most minute amount of sodium sulphide suffices to preclude development of water-repellency. Both oxygen and sulphide are in a sense, therefore, depres- sants for chalcocite in a lime solution at PH 10.5. When oxygen and sulphide are present simultaneously there is a region of minimum critical collector concentration for water-repellency which is very markedly lower than the concentration where oxygen alone or where sulphide alone is present. Moreover, this minimum appears to be identical with the collector concentration which is required where sulphide and oxygen are both excluded. This would appear to indicate that in certain ranges of concentration of oxygen and sulphide, each cancels the effect of the other. The range of concentration of solution for this effect in solutions saturated with oxygen is a function of the agitation intensity. Thus we are led to believe that a chemical reaction involving sulphide and oxygen occurs at the surface of the chalcocite. Part 4 of this study is a further development of this idea and some of its consequences from an electrochemical standpoint, while in Part 5 the disappearance of sulphide from pulps of several minerals is noted with an indication that both dissolved oxygen and the mineral are necessary, the reaction being catalytic or pseudocatalytic. Part 1. Determination of Fluid Film Thickness The Fluid Film Concept: The hindrance to the diffusion of collector to the surface of the chalcocite is a barrier of stagnant fluid in the vicinity of the surface. It is the same barrier that limits the rate of transfer of heat, the rate of solution of dissolving crystals, or any of the other rates pertaining to chemical engineering unit operations in which the film resistance to diffusion plays a principal role.&apos; Fluid films are present upon the surface to an extent which varies with the geometry and intensity of agitation. They result from the fact that in the region within the fluid near a surface, motion is entirely parallel to it. From the standpoint of transfer to or away from the interface the effect is as though the fluid were stagnant. Outside of the film, movement of the fluid may be streamline or turbu-

Jan 1, 1951

By S. Korman, S. B. Tuwiner

THE purpose of this study is to investigate the effect of agitation upon the flotation of chal-cocite. It is believed that the concentration of collector which is required to produce a water-repellent surface upon the mineral is determined among other things by the rate of collector diffusion through an impeding film of more or less stagnant fluid. Its thickness depends upon the intensity of agitation. In the first part of this study a method is developed for determining the thickness of the fluid film upon a polished surface of synthetic chalcocite. The film thickness is then determined as precisely as possible under three readily reproducible condi-tions of agitation intensity. These determinations serve as a quantitative evaluation of agitation. In Part 2 it is demonstrated that in solutions of lime at PH 10.5 and in the absence of air or dissolved oxygen the concentration of collector required to develop water-repellency upon the surface in any given time is a function of the fluid film thickness, and that after about 10 min the relation becomes linear. This points to the possibility that the collector ions may be involved in a diffusional process through the fluid film. In Part 3 it is shown that where air is present more collector is required to produce water-repellency than for the case in which air is excluded. Next, it is shown that for the latter case the most minute amount of sodium sulphide suffices to preclude development of water-repellency. Both oxygen and sulphide are in a sense, therefore, depres- sants for chalcocite in a lime solution at PH 10.5. When oxygen and sulphide are present simultaneously there is a region of minimum critical collector concentration for water-repellency which is very markedly lower than the concentration where oxygen alone or where sulphide alone is present. Moreover, this minimum appears to be identical with the collector concentration which is required where sulphide and oxygen are both excluded. This would appear to indicate that in certain ranges of concentration of oxygen and sulphide, each cancels the effect of the other. The range of concentration of solution for this effect in solutions saturated with oxygen is a function of the agitation intensity. Thus we are led to believe that a chemical reaction involving sulphide and oxygen occurs at the surface of the chalcocite. Part 4 of this study is a further development of this idea and some of its consequences from an electrochemical standpoint, while in Part 5 the disappearance of sulphide from pulps of several minerals is noted with an indication that both dissolved oxygen and the mineral are necessary, the reaction being catalytic or pseudocatalytic. Part 1. Determination of Fluid Film Thickness The Fluid Film Concept: The hindrance to the diffusion of collector to the surface of the chalcocite is a barrier of stagnant fluid in the vicinity of the surface. It is the same barrier that limits the rate of transfer of heat, the rate of solution of dissolving crystals, or any of the other rates pertaining to chemical engineering unit operations in which the film resistance to diffusion plays a principal role.&apos; Fluid films are present upon the surface to an extent which varies with the geometry and intensity of agitation. They result from the fact that in the region within the fluid near a surface, motion is entirely parallel to it. From the standpoint of transfer to or away from the interface the effect is as though the fluid were stagnant. Outside of the film, movement of the fluid may be streamline or turbu-

Jan 1, 1951

By J. N. Breston, R. V. Hughes

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20&apos;s before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

By R. V. Hughes, J. N. Breston

Conclusions drawn by previous research workers with reSPect to the relation between Pressure gradients and/or velocity and oil recovery obtained by laboratory water flood tests have been in disagreement probably due to variable procedures and unnatural conditions and materials. The Bradford Laboratory of the Pennsylvania Grade Crude Oil Association as part of its secondary recovery research program has conducted nineteen water floods on two long cores of widely differing characteristics in an attempt to clarify this relationship and make it an aid in predicting flooding pressures in the field. Unlike previous research procedures the present experiments were conducted with the aim of duplicating field conditions as closely as possible by using long unextracted consolidated cores, a live crude, and natural brines for both flooding and, connate water content. Also, the pressure gradients and flooding velocities were representative of field conditions where similar sands were being flooded. Eleven floods on one core and eight floods on the other core showed increased recoveries and lower residual oil saturation with increased flood pressure gradients and flood velocities. A marked decrease in recovery was obtained from both cores at very low flood velocities. This pressure versus recovery relationship is shown to hold up to the point of water breakthrough and also up to the 100 and 1 produced water to oil ratio point. INTRODUCTION The possibility of water flooding oil sands was suggested by Carl1 of the Pennsylvania Geological Survey in 1880. It is not known when the practice was tried intentionally for the first time, but its beneficial effects were noted in the annual production rate of the Bradford field as early as 1907. The practice was illegal in Pennsylvania until 1921. Early water floods in the Bradford field usually consisted of shooting or splitting the casing secretly to permit subsurface waters to enter the producing sands under hydrostatic head. As it was noted that the benefits of water flooding seemed to be proportional to the quantity of water dumped into the well many also began to utilize surface sources after the practice became legal. It was probably during the middle 20&apos;s before many producers realized that the pressurehead of the water upon the producing sand determined the rate and quantity of water that would enter the sand. Hence, rate and quantity of production appeared to be a direct function of input pressures. By 1927 a few producers had ventured the installation of pressure pumps in order to increase water-input rates and production through the combination of hydrostatic and hydraulic pressures. The adoption of pressure flooding and the "five-spot" drilling pattern in the Bradford field were essentially simultaneous. Water-input pressures in 1930 seldom exceeded 300 p.s.i. at the well head or 1100 p.s.i. at the sand face. Since that time, water-flood producers in the Bradford-Allegany fields have gone to higher and higher pressure until today 600 p.s.i. at the well heads is called a low pressure flood. Many high pressure floods now operate at 1300-1400 p.s.i. at the well head. The limiting and advisable pressure at the sand face has been pronounced as that pressure just under what is required to lift the overburden or to cause formation parting: According to this rule any water flood operation utilizing well-head pressures nearly equal in pounds per sq. in. to 1.1 times the average depth in feet to the top of the producing sand would be considered as a high-pressure flood. Despite the higher pressure trends in the Bradford-Allegany field operations and the results of early laboratory water flooding research, the desirability and benefits of high input pressures are still questioned by many operators, particularly in midwestern water flood operations. The present paper recounts a series of 19 laboratory water floods using two long, consolidated cores of widely differing characteristics saturated with live crude and flooded with oil field brines in an effort to simulate field conditions under • various pressure gradients and flooding velocities. For both cores, higher recoveries and lower residual oil saturations were obtained at higher pressure gradients and flood velocities. This relationship is shown to hold up to the water breakthrough point and also up to the 100 to 1 produced water to oil ratio point.

Jan 1, 1949

By H. C. Fiedler

Heats of high purity iron containing 3.1 pct Si and be -tween 0.0003 and 0.0295 pct N were prepared by vacuum melting ad then pouring while in a nitrogen atmosphere with the pressure between 0 and 90 psi. Strip from a heat with 0.0184 pct N underwent complete secondary recrystallization during the final anneal. Heats with less nitrogen had too few Si3N4 particles to restrain normal grain growth, and the heat with higher nitrogen had too many particles to allow complete secondary recrystallization. In the hot-rolled structure, Si3N4 precipitates only at the grain boundaries, with the consequence that annealing after hot-rolling diminishes the ability to subsequently undergo secondary recrystallization. In contrast to this behavior, ALNprecipitates uniformly in the hot-rolled structure. Under 1 atm of nitrogen, Si3N, in 3.1 pct Si-Fe dissociates between 900" and 950°C; the solubility of nitrogen increases from 0.0010 pct at 900" to 0.0030 pct at 1200°C. The solubility of nitrogen in Si-Fe has been the subject of many investigations. Corney and Turkdogan1 heated a 2.83 pct Si alloy in nitrogen and found the solubility, under 1 atrn of nitrogen, to be 0.0019 pct at 900°C. They claimed that Si3N4 did not form in the alloy above 705°C in 1 atrn of nitrogen. Fryxell et al.2 heated samples of 3.25 pct Si-Fe containing 0.0025 pct N over a range of temperatures and then analyzed for total nitrogen by vacuum fusion and for nitrogen in solution by a modified Kjeldahl technique. At 900°C, they reported the solubility of nitrogen in equilibrium with Si3N4 to be 0.0011 pct. pearce9 found the solubility of nitrogen at 900°C under 0.95 atrn of nitrogen to be 0.0017 pct in a 3.06 pct Si alloy. He reported that Si3N4 does not form above 770°C in 1 atrn of nitrogen. Although internal friction measurements have given somewhat higher values for the solubility,4-6 if the solubility of nitrogen is as low as has been reported by most investigators, and if Si3N4 is stable up to at least 945°C at 1 atrn pressure of nitrogen as reported by Seybolt,7 a small amount of nitrogen in properly processed Si-Fe should be effective in promoting secondary recrystallization. The requirement is that in the final heat treatment there be enough small, well-dispersed particles of Si3N4 to restrain normal grain growth. Fast8 has obtained secondary recrystallization by nitriding high-purity 3 pct Si-Fe after hot-rolling to a thickness of 0.118 in., followed by processing to 0.012 in., and annealing. A large amount of nitrogen, 0.076 pct. was introduced during the nitriding heat treatment, but he has since reported9 that "a few hundredths of a percent" is sufficient. Small amounts of aluminum10 or vanadium" nitride are capable of promoting secondary recrystallization. Heats containing as little as 0.010 pct A1 or 0.042 pct V and from 0.006 to 0.009 pct N underwent complete secondary recrystallization at final gage, whereas heats with lesser amounts of aluminum or vanadium did not.l2 To be reported is the behavior of nitrogen in high-purity 3.1 pct Si-Fe, and the relation of this behavior to the ability to undergo secondary recrystallization. PROCEDURE Ingots weighing 1 lb were made by vacuum melting high-purity electrolytic iron (A104, Glidden Co.) and high-purity silicon (Monsanto Co.). The latter was used in preference to ferrosilicon to insure a low aluminum content. The design of the melting furnace permitted pouring with the furnace atmosphere either below or above atmospheric pressure. Accordingly, at the completion of melting, nitrogen was admitted to the desired pressure and the heat then immediately poured. The ingots were sound, with no indication of porosity. In Table I are listed the heats investigated, the nitrogen pressure at pour, and the nitrogen and oxygen contents as determined by vacuum fusion with a platinum bath at 1850°C, a procedure which insures measurement of the total nitrogen.13 In addition, all heats contained 3.1 pct Si and not more than 0.002 pct C, 0.003 pct S or 0.005 pct Al. It was subsequently found that the quantity of nitrogen contained in the heats in Table I does not necessarily represent that obtained under equilibrium conditions. For example, the ingot poured immediately after 1 atrn of nitrogen was admitted to the chamber contained 0.0093 pct N, whereas an ingot poured 3 min after the nitrogen was admitted contained 0.021 pct N and another poured after a 6-min delay contained 0.029 pct N. While some bleeding of the hot top occurred in the latter instance, the ingot when examined in cross section appeared sound. The ingots were heated to 1325°C in hydrogen and rapidly rolled to 0.080 in. in 3 passes. The roll speed of the final pass was reduced so as to increase the quenching effect of the rolls. The hot-rolled pieces were processed both as-hot-rolled and after heating for 3 min at 900°C in hydrogen. After cold-rolling to 0.026 in., the strips were heated for 2 min at 900°C in hydrogen, then cold-rolled to the final gage of 0.012 in. The loss of nitrogen in going from the ingot to cold-rolled strip was no more than 10 pct. The final heat treatment, which was for the purpose of develop-

Jan 1, 1970

By G. P. Boomslitter

In previous discussions on stresses in hoisting ropes, little has been said concerning the effect of the elasticity of the rope itself on the stresses due to acceleration. Laschinger1 has calculated acceleration stresses for several cases but he has ignored the elasticity of the rope as a factor, except as it compresses the drum and stretches itself as it winds thereon. He also deals with steam plants and he shows the effect of the "jerky" start of the engine. This effect would actually be reduced by the elasticity of the cable. With the advent of the motor-driven hoist, new conditions have arisen. The jerk mentioned by Laschinger has been eliminated and smoother starting made possible. But the elastic properties of the rope seem to introduce considerable periodic acceleration stresses in the rope. The following discussion of acceleration stresses is based on the assumption of a constant acceleration at the drum. To be exact, the mathematical work is based upon the assumption that the top is moving upward with a constant acceleration, and ignores the fact that the cable is shortening as it winds. However, the effect of the shortening would be inconsiderable during the first part of the acceleration period. Most hoisting engineers make the assumption of constant acceleration at the drum. Under the older method of calculating acceleration stresses, this would be true with a constant torque motor. But if stresses vary, as this paper attempts to show that they do, constant torque would not give constant acceleration, although the velocity-time curves obtained in the full size test herein described showed that they approach rather closely to this condition, at least as nearly as could be measured. Theoretical Discussion According to elementary physics, the force required to accelerate a Wf body of weight W at the rate of f ft. per sec.2 is wf . To raise the body Wf with acceleration of f ft. per see.2 the total force required is I + Wf, in if

Jan 1, 1927

By Keith R. Bock, Norman Parlee, Albert M. Barloga

Coils of pure iron and iron-carbon alloy wire (0.05 to 0.80 pct C) and sufficient sulfur to saturate the solid phase were equilibrated in evacuated or argon filled tubes. After rapid cooling, and removal of the outside nonmetallic layer, the wires were analyzed for carbon and sulfur and the data used to construct an Fe-S binary and isotherms of the Fe-C-S ternary in the range 1149° to 1427°C. THE solid solubility of sulfur in steel is of interest in connection with such phenomena as hot shortness, burning, and so forth. "Burning," the more or less permanent damage that some steels suffer when heated for forging or rolling, has been shown to be related closely to the behavior of sulfur and less closely to carbon and oxygen.&apos; Attempts to interpret burning phenomena in steels fail because of lack of data on the Fe-C-S and the more complex systems in this family. Rosenqvist and Dunicz 2 and Turkdogan, Ignatowicz, and pearson3 have largely elucidated the Fe-S diagram in the region of interest but no information on the Fe-C-S diagram in this region appears to be available in the literature. This paper deals with the elucidation of the Fe-C-S diagram in these interesting ranges. The method employed is different from those used by previous workers2&apos;3 on the Fe-S system. EXPERIMENTAL METHOD Pure iron wires (Ferrovac E) or iron carbon alloy wires of 1 mm in diam were cleaned with acid and acetone, coiled, and placed in silica tubes (7 mm OD and 5 mm ID) previously closed at one end. Enough sulfur was added to assure saturation of the solid iron phase. The filled tubes were either simply evacuated and sealed, or filled with argon at a reduced pressure and sealed. The argon was required at the higher temperatures to prevent collapse of the tubes. The filled and sealed tubes were placed in the middle uniform temperature zone of a Globar tube furnace and equilibrated at temperatures ranging from 2100°F (1149°C) to 2720°F (1493°C). After equilibration the tubes were removed from the furnace and quenched in air or water, the form of quenching being found to have no effect on the results. The tubes were broken open and the coils were placed in a 1 : 1 HC1 solution to remove the sulfide-rich layer. The coils were then cut into small pieces and analyzed for sulfur and carbon. In the early stages of the investigation different equilibration times ranging up to 17 hr were tried and the cores of the wires were analyzed to test for saturation. One hour appeared to be sufficient to reach maximum sulfur content at 1454°C and 2 hr sufficient at 1149°C. The practice adopted was to use at least 3 hr at the higher temperatures and at least 5 hr at the lower temperatures. The iron-carbon alloy wires used were made by carburizing pure iron wire with carbon monoxide gas in a one inch diameter ceramic tube at about 1204°C. Differing carbon contents were obtained by allowing fairly large coils to react with the gas for varying lengths of time at a flow rate of 800 cc per min. The reacting times ranged from 15 min to 4 hr depending upon the amount of carbon desired. The furnaces used were controlled by means of Leeds and Northrup Speedomax Type H instruments with D.A.T. Control attachment. Thermocouples were calibrated against the melting points of gold and copper. The temperatures recorded appear to be accurate within i2.7OC. Starting with run No. 85 and continuing with the

Jan 1, 1962

By D. E. Stephenson. Discussion by R. G. K. Morrison, L. Obert

R. G. K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que., Canada) - The discing of drill core has been a recognized pressure phenomenon for many years but only recently has an interest been taken in the mechanism involved. The work of Jaeger and Cook is referred to in the text. The authors have now advanced the study to establish, within certain loading limitations, a direct relationship between axial and radial stress at failure. This is an important contribution. In mines generally, where pressure conditions result in the spalling of openings, the faces of drifts and crosscuts, on scaling, usually show a concavity with respect to the opening very similar to the face of the drill hole after the separation of the stub. The same holds for shaft sinks. This suggests a similarity between the mechanism of the discing of core and that of the spalling of an opening, under pressure, to develop a more stable outline. The latter, commonly regarded as shear, is the most conspicuous type of failure observed in

Jan 1, 1967

By D. T. Peterson, T. Carnahan

The diffusion coejTicients of carbon, nitrogen, and oxyget were determined in $ thorium over the tempernilcre range 1440" io 1715°C. The diffusion coyfiicir?zls are given by: D = 0.022 exp (-27,000/RT) jor carbo)~, D = 0,0032 exp(-l7,00Q/RTj for nitrogen, and D = u.0013 expt(-11,UOU/RT) for oxygen. Cavl~orz was found to increase the hardness of thoriunz nearly linearly with concentration over the range 100 to 1000Ppm carbon. ThORIUM has a fcc structure up to 1365°C and a bcc structure from this temperature to its melting point at 1740°C. Diffusion of carbon, oxygen, and nitrogen in bcc thorium was of interest in connection with the purification of thorium by electrotransport.&apos; In addition, it was possible to measure the diffusion of all three of these interstitial solutes in the same bcc metal. Only in niobium, tantalum, vanadium, and a iron have all three interstitial diffusion coefficients been measured in a given bcc metal. Diffusion coefficients have been measured for carbon and oxygen in a thorium by Peterson2, 3 and for nitrogen by Gerds and Mallett.4 Activation energies for diffusion are reported by the above authors to be 38 kcal per mole for carbon, 22.5 kcal per mole for nitrogen, and 49 kcal per mole for oxygen. Values of the diffusion coefficients of carbon and nitrogen in 3 thorium have been reported by Peterson et al.&apos; However, these were secondary results of their investigation of electrotransport phenomena in thorium and it was hoped that the present study could provide more precise data. EXPERIMENTAL PROCEDURE The specimens used in this study were the well-known pair of semi-infinite bar type. The couple was formed by resistance butt welding two 0.54-cm-diam by 3.0-cm-long bars of thorium together under pure helium, the concentration of the solute being greater in one cylinder than that in the other. The finished couple then contained a concentration step at the weld interface and diffusion proceeded only along the axis of the rod. The thorium used in this study was prepared by the magnesium intermediate alloy method.5 The total impurity content was less than 400 ppm. The major impurities were: carbon, 100 ppm: nitrogen, 50 ppm; and oxygen. 85 ppm. The total metallic impurity content was less than 150 ppm. The high solute concentration portions of the diffusion couples were prepared by adding the solute to the high-purity thorium in a non-consumable electrode arc melting procedure. Carbon and nitrogen were added in the form of spectroscopic graphite and nitrogen gas while a Tho2 layer was dissolved by arc melting to add oxygen. High-purity thorium formed the low concentration portions in the carbon and nitrogen couples. The low oxygen portions were obtained by deoxidizing high-purity thorium with calcium for 3 weeks at 1000°C according to a method reported by Peterson.3 The high C-Th contained 400 ppm C, the high N-Th contained 400 ppm N, the high 0-Th contained 220 ppm 0, and the low 0-Th contained 25 ppm O. The high O-Th was brine-quenched from 1500°C to retain most of the oxygen in solution at room temperature. These concentration levels were all below the solubility limits in 0 thorium at 1400°C. A resistance-heated high-vacuum furnace was used to heat the couples. The samples were mounted horizontally on a tantalum support which had small grooves near each end. Spacer rods of thorium, 0.4 cm in diam, were placed in these grooves to prevent contact between the sample and the tantalum support. This arrangement should have prevented contamination of the sample by contact with the support. In further effort to reduce contamination, the oxygen diffusion couples were sealed inside evacuated outgassed tantalum cylinders lined with thorium foil. Thorium rings around each end of the samples acted as spacers in this case. Pressure during diffusion runs was about 10-6 torr after an initial outgassing stage. Temperature measurements were made by sighting on black body holes in the sample support adjacent to the samples with a Leeds and Northrup disappearing-filament optical pyrometer. Temperatures were constant during a diffusion anneal to ±5C. The observed temperatures were corrected for sight glass absorption after each diffusion run. The pyrometer was checked against a calibrated electronic optical pyrometer and a calibrated tungsten strip lamp with the electronic pyrometer being taken as the standard. All temperature readings agreed to within ±3C over the temperature range 1450" to 1690°C. Time corrections due to diffusion during heating and cooling were necessary because of the short diffusion times. The diffusion times ranged from 6 min for the oxygen sample run at 1690°C to 90 min for the carbon sample run at 1500°C. A series of temperature vs time plots were made for heating and cooling of the samples to the various diffusion temperatures. This data was then used in a method according to shewmon6 to determine the time corrections. The corrections amounted to

Jan 1, 1970

By J. V. Richards

(Canal Zone Meeting, November, 1910,) THE Altar district, State of Sonora, Mexico, is for the most part a desert with but little rain-fall and few running streams. On account of this scarcity of water it is necessary for the natives to " dry-wash" the placer-gravel, and the object of the present paper is to describe some of the more common Mexican dry-washing devices. My observations were confined to a property known as Las Palomas placers, 15 miles from the Gulf of California and about 150 miles south of the United States border; a brief description of which property may be of interest as illustrating what is, perhaps, a typical Sonora dry placer. It is said that as long as a century ago the Yaqui Indians discovered rich cement-gravel, known as argo masa, at Las Palomas, and that there has been a more or less steady production of gold from the property ever since. The argo masa is a fairly-coarse gravel, the pebbles being quite firmly held together with a lime cement. Gold is scattered through this cement in particles ranging from fine specks to pieces several grams in weight, and occasional large nuggets are encountered. The contents vary so widely that it is difficult to estimate the average value, but returns of from $10 to $50 per cubic yard are common, and it is doubtful if the Indians considered anything less than from $4 to $5 a yard as "pay dirt." This argo masa occurs in channels varying in thickness from a few inches to several feet, and in width up to 300 ft.. These channels are continuous and are probably ancient stream-beds. They are for the most part covered with an over-burden of a more recent gravel, varying from 30 to 50 ft. thick, and the fact that this over-burden contains values as high as $1.50 per cubic yard, and yet was not worked by the Indians, shows that their idea of what constituted pay-ground was high.

Apr 1, 1911

By N. M. Langdon

In considering the magnificent success of Mr. Gayley&apos;s bold experiment of applying dry blast to the blast-furnace, whereby a saving of 20 per cent. of fuel per ton of iron is effected, the question arises whether still further economy in fuel is possible, and, if so, how it is to be attained. The manner in which the heat generated in the furnace is utilized in the production of pig-iron may be determined, by the method of Bell and Gruner, for any furnace for which the necessary data are obtainable ; and the study of the operation, under various conditions, of a number of furnaces, for which such information has been worked out, should enable us to form some conclusion on the subject. The tables and calculations here given cover the operations of several furnaces reported in our Transactions ; also the two furnaces using natural and dry blast ill Mr. Gayley&apos;s experiment, for which the heat-equation has been worked out by Prof. Joseph W. Richards in his admirable discussion &apos; of Mr. Gayley&apos;s paper, The Application of Dry Air Blast to the Manufacture of Iron, and, finally, various hypothetical furnaces. The full list is as follows : A. Isabella furnace, with natural blast. B. Isabella furnace, with dry blast. The data stated for A and B in Table 111. are those given by Professor Richards, except that the heat-units are given for one unit of iron instead of 100 units, and some items of heat supplied, as stated by Richards, have been subdivided, the total being the same as given by Richards. (Columns A and B are introduced in Table 111. for comparison with C and D.)

Jan 1, 1910

By Olaf Hondrum

CHURN drilling equipment at Bagdad consists of two Bucyrus Erie 27-T model drills and one 22-T drill with gasoline engines. The drilling tools weigh approximately 1600 lb. The holes are drilled with 7-in. bits which are heated in an oil burning furnace and sharpened in an electrically powered bit sharpener. A service truck brings the bits to the drills and takes the dull bits back to the shop. The bits weigh around 250 lb. when new and are handled by drill crews without any mechanical handling device. When the management decided to start open- pit operations in 1945 the ruggedness of the terrain was one factor that led to the purchase of the small 22-T model drill. The orebody lies on both sides of Copper Creek Canyon. The sides of the canyon are steep and are cut by numerous narrow branch gullies. The drill had to travel over roads that were narrow and steep. It proved adequate for drilling the capping formation and is still in use.

Jan 1, 1950

By B. H. Caudle, R. L. Slobod, E. R. Brownscombe

An earlier publication has discussed three methods lor obtaining relative permeability data on small core sample-: and the apparatus and technique for the capillary pressure displacement method. This paper describes the apparatus and technique for the solution gas and the dynamic displacement methods and presents a routine procedure for obtaining oil-gas and water-oil relative permeability data. Theoretical and experimental considerations are presented to show that the end effect commonly associated with the dynamic flow mechanism is extremely small where constant rates are employed in the flowing phase. An effect of flow rate on relative permeabilities obtained by the dynamic system is found only when gas is one of the flowing phases and this effect is ascribed to a form of channeling in the capillary system. The apparatus and procedure* used to obtain relative permeability data with three phases flowing are described and some preliminary results of the use of this method are shown. INTRODUCTION In a previous publication from this laboratory there appeared a brief discussion of the concepts behind three basic methods for obtaining relative permeability data.&apos; These three methods were called the capillary pressure displacement method. the solution gas displacement method, and the dy. namic displacement method — the names being suggestive of the type of process used for obtaining the desired saturation prior to making the permeability measurements. In the same publication, the apparatus and technique for the capillary pressure displacement method were described and some typical results obtained by this method were presented. This paper will present: 1. The routine procedure used to obtain complete relative permeabilitv data (In small core samples with two phasec flowing; 2. The experimental techniques for the solution gas and dynamic displacement methods for obtaining relative permeability data; 3. The results of some studies on the mechanism of fluid flow through consolidated porous media; and, 4. The preliminary results on the determination of relative permeability for a system in which three phases are flowing. TECHNIQUE AND APPARATUS FOR THE DETERMINATION OF RELATIVE PERMEABILITY WITH TWO PHASES FLOWING In order to obtain relative permeability data on a small core sample which will describe the various phases of reservoir depletion. it is necessary that the methods used duplicate, as closely as possible, the various mechanisms involved in rescbrvoir depletion. It is important that. in any type of relative permedbility determination. the core be originally at virgin reservoir conditions with respect to the fluids within the pore *paces. (for example. oil used to displace water from core until connate water saturation estahlished). and that the subsequent saturation changes in the core be analagous to tile reservoir depletion mechanism for which the data are to he used. PROCEDURE OF DETERMINING RELATIVE PERMEABILITY DATA WITH TWO PHASES FLOWING A standardized procedure has been set up for obtaining relative permeability data and other information on small core samples. This procedure essentially consists of 11 steps as shown below: 1. Determination of tile capillary pressure curve.&apos;! This information is used to help select samples for relative permeability determinations and to charactrrize. in general. the pore size distribution of the sample. 2. Determination of the specific permeabilities to air, oil. and water. These values are those on which the relative pern~eahility calculations are based. 3. Reduction of the core to connate water by an oil drive using the high speed centrifuge. 1. Determination of the critical gas saturation value and the associated relative permeability to oil by the solution gas drive method. 5. Determination of the relative permeabilities to oil and gab in the region where both phases are flowing by the capillary presqure method. 6. Reduction of the sample to residual oil in the centrifuge by an air drive. and the determination of the relative permeability to gas at this point.

Jan 1, 1951

By R. L. Slobod, B. H. Caudle, E. R. Brownscombe

An earlier publication has discussed three methods lor obtaining relative permeability data on small core sample-: and the apparatus and technique for the capillary pressure displacement method. This paper describes the apparatus and technique for the solution gas and the dynamic displacement methods and presents a routine procedure for obtaining oil-gas and water-oil relative permeability data. Theoretical and experimental considerations are presented to show that the end effect commonly associated with the dynamic flow mechanism is extremely small where constant rates are employed in the flowing phase. An effect of flow rate on relative permeabilities obtained by the dynamic system is found only when gas is one of the flowing phases and this effect is ascribed to a form of channeling in the capillary system. The apparatus and procedure* used to obtain relative permeability data with three phases flowing are described and some preliminary results of the use of this method are shown. INTRODUCTION In a previous publication from this laboratory there appeared a brief discussion of the concepts behind three basic methods for obtaining relative permeability data.&apos; These three methods were called the capillary pressure displacement method. the solution gas displacement method, and the dy. namic displacement method — the names being suggestive of the type of process used for obtaining the desired saturation prior to making the permeability measurements. In the same publication, the apparatus and technique for the capillary pressure displacement method were described and some typical results obtained by this method were presented. This paper will present: 1. The routine procedure used to obtain complete relative permeabilitv data (In small core samples with two phasec flowing; 2. The experimental techniques for the solution gas and dynamic displacement methods for obtaining relative permeability data; 3. The results of some studies on the mechanism of fluid flow through consolidated porous media; and, 4. The preliminary results on the determination of relative permeability for a system in which three phases are flowing. TECHNIQUE AND APPARATUS FOR THE DETERMINATION OF RELATIVE PERMEABILITY WITH TWO PHASES FLOWING In order to obtain relative permeability data on a small core sample which will describe the various phases of reservoir depletion. it is necessary that the methods used duplicate, as closely as possible, the various mechanisms involved in rescbrvoir depletion. It is important that. in any type of relative permedbility determination. the core be originally at virgin reservoir conditions with respect to the fluids within the pore *paces. (for example. oil used to displace water from core until connate water saturation estahlished). and that the subsequent saturation changes in the core be analagous to tile reservoir depletion mechanism for which the data are to he used. PROCEDURE OF DETERMINING RELATIVE PERMEABILITY DATA WITH TWO PHASES FLOWING A standardized procedure has been set up for obtaining relative permeability data and other information on small core samples. This procedure essentially consists of 11 steps as shown below: 1. Determination of tile capillary pressure curve.&apos;! This information is used to help select samples for relative permeability determinations and to charactrrize. in general. the pore size distribution of the sample. 2. Determination of the specific permeabilities to air, oil. and water. These values are those on which the relative pern~eahility calculations are based. 3. Reduction of the core to connate water by an oil drive using the high speed centrifuge. 1. Determination of the critical gas saturation value and the associated relative permeability to oil by the solution gas drive method. 5. Determination of the relative permeabilities to oil and gab in the region where both phases are flowing by the capillary presqure method. 6. Reduction of the sample to residual oil in the centrifuge by an air drive. and the determination of the relative permeability to gas at this point.

Jan 1, 1951

By Sumner M. Anderson

Any discussion of outside support to Latin American mineral industries must concede at once the pre-eminent role of U. S. industry and business. American capital has developed the great copper resources of Chile and Peru, the lead-zinc of Peru and Mexico, the bauxite of Surinam and Jamaica, the petroleum and iron ore of Venezuela. American consumers have provided the market for their products. U. S. companies operating south of the border have trained Latin American geologists, engineers, chemists, and skilled labor—including metal, mineral, and fuel technicians—to new and greater competence. The industrial demands of World War II drastically altered world economics and concepts of U. S. foreign mineral requirements. In this country discovery of vital mineral resources fell far behind the alarming depletion rates, and there was new appreciation of the actual and potential importance of the world&apos;s less extensively explored areas. During the war and afterward, the task of supplying the nation&apos;s mineral requirements became greater than private industry could carry alone, and the Government assumed a position of continuing support. In Latin America, as elsewhere, this support applies in three categories: banking, procurement, and technical assistance. The first two are now generally accepted as necessary Government functions; the third has often been misunderstood and misinterpreted, although it has given rise to legitimate controversy. There have been major accomplishments in all three categories, as well as some errors of judgment. Since the beginning of World War 11, U. S. Government financing, procurement, and technical assistance have been applied on a large scale to a wide range of commodities and services throughout the free world. The present discussion—under the separate headings mentioned—will concern only the support related to a single industrial group in a single geographic area. During the War Federal banking was conducted on an emergency scale by temporary agencies created to meet the abnormal circumstances. Unfortunately, there are no readily available data on these activities that would permit evaluating loans and credits extended for mineral projects in Latin America. The only agency operating in this field since World War II is the Export-Import Bank, under its own authority and to some extent from credits authorized by the Office of Defense Mobilization. The Bank can offer more capital—on more favorable terms—than is available from most Latin American banks, and its staff of engineers evidently can appraise loan applications more favorably than commercial banks in this country are willing to do. The risks seem to be justified, as defaults have been well under 1 pct of total loans. From V-J day 1945 to the end of 1957, mineral loans to Latin America have been authorized for projects totaling $541.63 million in eight countries. In order of magnitude of credits, they have been made to Brazil, Peru, Chile, Mexico, Argentina, Venezuela, Guatemala, and Bolivia. In order of magnitude by industries. they are for development and expansion of steel mills, copper, manganese, nitrate plants, iron ore, zinc plants, sulfur plants, cement plants, tungsten, coal, and lead. Loan Distribution: By far the largest loans have been $307.9 million for iron and steel projects in Brazil, Chile, Mexico, Argentina, and Peru: $100.4 for developing the great low-grade copper deposits of southern Peru; and $55.3 million for developing manganese deposits in the Territory of Amapa, Brazil. Others range from $20.8 million for a zinc smelter in central Peru to $19 thousand for iron-mine trucking equipment in Chile. It has been noted that 59 pct of the loans have been to foreign companies, 14 pct to companies of mixed foreign and American capital, and 27 pct to American mining companies. About 40 pct of the total authorizations has been disbursed so far. In addition to these amounts, the Strategic Materials Division of the Economic Cooperation Admin-

Jan 1, 1959

By W. F. Rochow, W. C. Burke

Numerous designs of linings and accessories, including dams, lifters, and heat exchangers, contribute greatly to kiln efficiencies. Greater conductivity is achieved with basic brick than with fireclay and high-alumina refractories, depending largely upon the use of steel plates in radial joints between adjacent brick to increase heat transfer through the lining. Refractory lifters expose all portions of the load to radiant or convective heat and raise some portions to higher temperatures by cascading the load down through the path of the hot gases. AMONG the many factors involved in rotary kiln efficiency, advantageous use of refractories is of major importance. So far as kiln lining alone is concerned durability is most significant, as shutdowns for repairs are costly in fuel consumption and production losses. Aside from selection of refractories best suited to the widely varying conditions under which rotary kilns are operated, lining design and accessory constructions within the kiln are highly important. The refractory most economical for any combination of operating conditions can be selected from a wide range of alumina-silica and basic refractories, including insulating, castable, and plastic fire bricks. In several cases silica brick can be used to advantage. Alumina contents of alumina-silica refractories range from 35 to 90 pct in increments of 5 to 10 pct. In general, bricks of relatively low alumina content are best for abrasion resistance, an important property for the brick used in chain sections of cement kilns or in feed end sections of limestone kilns. High-duty fireclay bricks of approximately 40 pct alumina and 55 pct silica are used to line the intermediate zones. Super-duty fireclay brick at slightly higher cost is warranted in operation of kilns with high intermediate zone temperatures and severe spalling conditions. Alumina-silica refractories with an alumina content of 50 pct and higher, termed high-alumina brick, are available in commercial classes of 50, 60, 70, 80, 85, and 90 pct alumina content. These refractories are generally used as high temperature zone linings or placed adjacent to the basic brick-lined sections when the treatment they are required to withstand is excessively severe. Use of basic refractories is confined mainly to zones of maximum temperature and most severe chemical action. Basic refractories ordinarily employed for high temperature zone linings of many rotary kilns comprise the classes shown in Table I. Each class is peculiarly well suited to various particular combinations of working conditions. The approximate chemical analyses of these classes also illustrate differences in compositions with respect to the major components.

Jan 1, 1956

By LE B. GRAY

ALL meeting of the Chemical Section, National Safety Council, in Rochester, N. Y., put his hand on at least ten salient points that apply to safety in nearly any laboratory ; these are as follows : 1. Impress your laboratory worker at the start that he is dealing with powerful and dangerous-forces and that every experimental set-up must be studied from the stand- point of its fiber, electrical, explosive, and health hazards.

Jan 1, 1929