Search Documents

By R. M. Waterstrat

The phase VPt has been reported to have a crystal structure of the B19 (AuCd) type at low temperatures.''' A recent investigation3 has indicated that this phase forms by an ordering reaction from the disordered fcc Pt(V) solid solution which is stable at high temperatures. olander4 has shown that there exists a close structural relationship between the orthorhombic B19 structure and a fcc structure possessing the L1 , (CuAu) type of atomic ordering. One may derive the B19 structure by a shear-like displacement of the atoms in the (002) plane of the ordered fcc lattice along the (010) direction through a distance equal to one eighth of the unit cell dimension, see Fig. 1, followed by an orthorhombic distor; tion of the cube axes such that a = 2.693A. h = 4.413A. and c =4.767A (estimated uncertainty 0.005A). Filings of this phase were produced by grinding a VPt alloy having the B19 structure with a diamond dental grinding disc. When these filings were subjected to X-ray diffraction examination, a pattern of a severely cold-worked fcc structure was obtained. higher solution temperature used (1200 C) or to a much lower oxygen pressure than he reported, due to transfer through many bends and tubes in his complicated apparatus. An interesting observation was made when an oxygen addition was attempted in a cylindrical sample of columbium in the cold worked condition rather than in the annealed condition. The interior of the sample re-crystallized during the oxygen addition at 900°C. The periphery, however. (1 mm) did not recrystallize. A similar sample without oxygen recrystallized throughout the entire cross section. It appears that the re-crystallization is hindered by interstitial oxygen. Presumably, the interior recrystallized before appreciable oxygen could diffuse into the core. This work was supported by the United States Atomic Energy Commission. When the filings were annealed in a high vacuum furnace for 15 min at 110O0C, however. they returned to the B19 structure perhaps as a result of reordering. Subsequent less-severe cold-working of these filings by grinding in a hardened steel mortar and pestle at room temperature produced a transformation into a cold-worked L1, structure which was slightly tetragonal. Thus it appears that the degree of deformation may influence the final structure. Considerable line-broadening was observed in X-ray diffraction patterns obtained from the cold-worked filings and therefore no attempt was made to obtain accurate lattice parameters. Vacuum annealing treatments at 1100'C intended

Jan 1, 1970

By A. N. Mitinsky

(San Francisco Meeting, September, 1915) THE theory of elasticity, the science of the strength of materials, and all our calculations regarding engineering structures are based on Hooke's law, that in loaded bodies the deformations are, proportional to the load producing them. Without this law it would be impossible to design intelligently engineering structures such as bridges, frames, axles, etc. This being the case, the proportional limit,1 that is, the point at which deformation ceases to be proportional to load, is the most important factor in engineering design. Further, the working fiber stress should be fixed in reference to the proportional limit instead of, as is usual, in reference to the ultimate strength. The incorrect use of the ultimate strength instead of the proportional limit in setting the working fiber stress is probably clue to two reasons: (1) it is a more delicate operation to measure the proportional limit; (2) it is usually -assumed, though incorrectly, that the proportional limit is determined by the ultimate -strength. In Germany the point at which permanent set first appears is often taken instead of the proportional limit. The two points will coincide if Gerstner's law, that elastic deformations are proportional to the loads producing them both before and after permanent set, is true; and the limit of proportionality and the elastic limit or point of permanent set will both 'be represented on a stress-strain diagram, by the point at which the line ceases to be a straight line and becomes curved-or changes its inclination. It is to be further noted that the difference in definition between proportional limit and elastic limit introduces a difference in methods of determination in the testing laboratory. The German method of determining. the elastic limit by alternately loading and unloading

Jan 8, 1915

By William P. Prof. Blake

WHEN we consider the efforts made in Europe to promote the physical and moral well-being of the working classes, the question is suggested whether in this country, where, theoretically, every man is peculiarly the arbiter of his own destiny, we may not be too prone to expect every man to take care of himself, and neglect to make those provisions for the welfare of the employed, demanded alike by enlightened economy and humanity. In the older countries, where the disproportion between capital and labor is greater, and the working classes are more dependent, their welfare largely occupies the attention of employers. The subject is involved in the problem of the just relations of capital and labor, and we are rapidly approaching the time, if we have not already reached it, when a generous paternal interest in the welfare of the employed should be more generally manifested. It is a subject which is of special importance to mine-owners and engineers in this country, especially to those located in the coal regions. My own attention has been particularly directed to it by a visit made to the Hassard collieries, a few miles from Liege, Belgium, under the direction of M. Andrimont. This celebrated engineer has established a comfortable home for the miners near the mouth of the shaft of the mine. It has been highly successful and beneficent in its results, and may to a great degree be regarded as a, model for such undertakings. It is known as "Hotel Louise," this being the name of Madame d'Andrimont, who laid the corner-stone of the building April 4th, 1871. The structure is of brick, upon three sides of a square, and

Jan 1, 1875

By William P. Blake

When we consider the efforts made in Europe to promote the physical and moral well-being of the working classes, the question is suggested whether in this country, where, theoretically, every man is peculiarly the arbiter of his own destiny, we may not be too prone to expect every man to take care of himself, and neglect to make those provisions for the welfare of the employed, demanded alike by enlightened economy and humanity. In the older countries, where the disproportion between capital and labor is greater, and the working classes are more dependent, their welfare largely occupies the attention of employers. The subject is involved in the problem of the just relations of capital and labor, and we are rapidly approaching the time, if we have not already reached it, when a generous paternal interest in the welfare of the employed should be more generally manifested. It is a subject which is of special importance to mine-owners and engineers in this country, especially to those located in the coal regions. My own attention has been particularly directed to it by a visit made to the Hassard collieries, a few miles from Liège, Belgium, under the direction of M. Andrimont. This celebrated engineer has established a comfortable home for the miners near the mouth of the shaft of the mine. It has been highly successful and beneficent in its results, and may to a great degree be regarded as a model for such undertakings. It is known as ((Hotel Louise," this being the name of Madame d' Andrimont, who laid the corner-stone of the building April 4th, 1871. The structure is of brick, upon three sides of a square, and

By Henry M. Howe

THE natural effect of large size should be to increase segrega¬tion. I have previously pointed' to the excessive segregation in many large ingots as tending to confirm this, but I have shown that in case of ingots less than 16 in. square this expected effect of ingot-size is liable to masked by that of other variables. Under these conditions we should expect that if large ingot-size really does tend to increase segregation, this effect would be shown by taking the average of large numbers of cases, so that the effects of these other variables might off-set and cancel each other.

Jan 10, 1909

By J. Pinto, F. Galasso

THE current emphasis in preparing boron fibers by reduction of gaseous boron compounds on a resistively heated metal wire substrate has renewed interest in the borides of those metals which have relatively high melting points and are available as fine wires. A knowledge of the structures and properties of the borides, which are formed when boron diffuses into the metal core during boron deposition, can be of assistance in the understanding of the boron fiber formation process and the fiber properties. Many of these borides are well-known and their properties have been measured. However, when an unidentified boride is found in the core, it may be difficult to establish its composition because of the small amount of material available, the preferred orientation effects on the reflections in its X-ray pattern, and the possible overlap of X-ray reflections if several borides are present in the core. For example. the proper indexing of the X-ray pattern of WB4, which was formed in the tungsten substrate core during boron fiber formation, was accomplished only after small single crystals of this boride were grown and X-ray precession investigations were conducted.' This note presents the results of a study of the phases formed in the core when tungsten, tantalum, and molybdenum metal wires were used as substrates in the boron fiber preparation process with particular emphasis on the identification and characterization of a higher boride of molybdenum analogous to WB,. Boron was deposited on resistively heated stationary 0.0012-in.-diam tantalum, tungsten, and molybdenum wires at 1050°C for various times up to 60 sec using boron trichloride and hydrogen as the reactant gases. After 60 sec of boron deposition the fibers were approximately 0.006 in. in diam. Examination of photomicrographs of fiber cross sections showed that the boron had diffused nearly to the center of the tungsten and molybdenum cores in 15 and 30 sec, respectively, and only halfway to the center of the tantalum core in 60 sec. X-ray diffraction photographs of the fibers indicated that it was also after 15 and 30 sec deposition times that the tungsten and molybdenum metal reflections, respectively, had disappeared from the X-ray patterns of the fibers. The patterns of the boron fibers produced using tantalum wire as a substrate showed that amorphous boron, TaB2, and tantalum metal were present after a few seconds deposition time and remained even after deposition times of 60 sec. Until a deposition time of 15 sec was reached, the tungsten substrate fibers contained amorphous boron,273 6WB, W2B5, and WB4 as well as tungsten metal, while the molybdenum substrate fibers contained amorphous boron, MoBa, Mo2B5, and molybdenum metal for deposition times up to 30 sec. Just before the molybdenum metal pattern disappeared, a pattern similar to that of WB, appeared, suggesting that a phase, MOB,, isomorphous with WB,, was present in the fiber. This same pattern was obtained from the product formed by heating a mixture of molybdenum metal and excess boron powder in a boron nitride crucible at 1960°C in an argon atmosphere. As was the case with the WBn pattern, this pattern could best be indexed on the basis of a hexagonal unit cell rather than the tetragonal unit cell Chrktien and Helgorsky reported for ~0~4,~ see Table I. The unit cell parameters for MoB4 were calculated to be a, = 5.214A, co = 6.358A. Assuming the space group P63/mmc and positions5 2M01 in 2b and 2MoII in 2c found for tungsten in WB~,' a logical structure for MOB, was determined using geometrical considerations to place the boron

Jan 1, 1969

By Charles Rich, Robert Munson, Leonard Obert

Improved methods of predicting the caving characteristics of ore bodies is discussed. Experiments were conducted at Climax mine, Climax, Colo., on varied rock compositions. The cavability of adjacent areas, as well as seismic energy absorption proved to be good factors in determining cavability. Seismic velocity, core recovery, and rock quality designation (RQD) were found to be not as reliable.

Jan 1, 1977

By T. A. Griffin

Surface mining today is faced with a twin challenge: (1) accelerating the rate of removal of massive quantities of overburden and ore, and (2) replacing comparable high volumes of overburden in the mined-out portion of the pit. It is against this background, coupled with increased demands for fossil fuels worldwide and legitimate environmental concerns, that the role of bucketwheel excavators and reclaimers has been raised to new prominence.

Jan 10, 1974

By P. Bardzil, J. Gurland

An experimental study of the variation of transverse-rupture strength with composition Anexperimentaland grain studysize has shown that the strength reaches a maximum for values of the mean free path between carbide particles of 0.3 to 0.6 microns. The fracture oforiginates in and proceeds through the carbide grains mainly. Impact strength and hardness also were recorded. MOST of the physical properties of sintered carbides vary linearly with composition. The transverse-rupture strength, however, shows a unique behavior. As the amount of binder metal is varied from 6 to 25 pct by weight, the strength at first increases; then, between 15 and 20 pct Co, it reaches a maximum of nearly 400,000 psi, and finally decreases with further additions of binder metal. This behavior of the transverse-rupture strength has been reported, among others, by Englel and Sandford and Trent.' The significance of these observations has not been discussed in the literature. That it may be of more than specific importance is indicated by the very similar variation of strength with composition encountered in other systems sintered in the presence of a liquid phase, such as Tic-Ni3 and Fe-Cu.' Experimental Details All compacts were prepared and sintered according to normal industrial practice. The average diameter of WC grains and the mean free path between grains were measured on metallographically prepared samples by a method of linear and planar analysis sing the relations where d is the average diameter of dispersed grains; Nl is the number of noncontiguous grains intersected on a metallographic plane by a line of unit length; N, is the number of noncontiguous grains per unit area; P is the mean free path between grains of dispersed phase; and f is the volume fraction of dispersed phase. Approximately 1000 grains were counted on each sample. For each composition d2 was plotted against P, the resulting straight lines serving as a check on the measurements. The distribution curves of the WC powders of different average diameters were homologous, and no attempt was made to influence the grain size by blending powders, adjusting the sintering conditions, or otherwise altering the particle size distribution. Densities were measured by differential weighings in air and water. The degree of densification did not vary consistently with either composition or grain size. The density is influenced by slight amounts of impurities, specifically by 0.1 to 0.2 pct Fe which enters the powders during ball milling. As an illus- -tration of the experimental variations, a number of measured densities are listed in Table I. They are expressed in percentage of theoretical density, as calculated from the published X-ray densities of WC and Co.' For the purpose of determining the transverse-rupture strength, rectangular test specimens (3/16x 3/8x3/4 in.) were broken by loading at the center of a 9/16 in. span. The average strength of five or more samples is reported for each composition and grain size. The compacts were ground on two parallel surfaces only. The load was applied at an average rate of 6,800 psi per sec. Since the elongation after fracture of the alloys is very small, it was assumed that the compacts deform elastically to failure and the fracture stress was calculated by the conventional beam formula. The data for one alloy are presented in Table II as an example of the results and scattering ranges encountered. The precision of the test, as measured by the average difference between duplicates, is of the order of 15,000 psi. The results are strictly comparable only to compacts prepared and tested in the manner described and of similar chemical composition and grain size characteristics. Unnotched Charpy specimens were used for impact testing. Each point represents the average of 3 to 20 samples, the larger number being used in an attempt to determine the influence of grain size. Considerable scatter was encountered, the range from lowest to highest value often amounting to 30 pct of the impact strength. The hardness is reported as a Ra reading, using a 60 kg load with diamond brale indenter. Compositions are given in weight percent.

Jan 1, 1956

By E. Teghtsoonian, K. G. Davis

Cobalt crystals of commercial purity have been tested in tension. Their resolved shear stress-shear strain curves are very similar in form to those for zinc, magnesium, and cadmium. There is an initial linear region for shear strains up to around 150 pct, the ratio of work hardening slope to shear modulus at room temperature being about 2 X x This is followed by an upturn, which is, PLASTIC deformation in metal single crystals with close-packed structures has been found strongly dependent on stacking-fault energy. The high stacking-fault energy hexagonal metals magnesium, zinc, and cadmium have been quite extensively tested, but up to now no data have been available for a comparable hexagonal metal with low stacking-fau1t energy' An however, smaller in magnitude for cobalt than for the other metals. Values for the critical resolved shear stress rise from 97 kg per sq cm at room temperature to approximately 170 kg per sq cm at -196 °C. The Cottrell-Stokes ratio is not constant either for variations in the strain rate or for temperature changes, its value decreasing with strain. investigation into the plastic deformation of cobalt, which has a very low stacking-fault energy, has therefore been undertaken. EXPERIMENTAL PROCEDURES Cobalt crystals in the form of rods 0.3 cm in diam were grown in an electron-beam floating-zone refiner at a rate of zone travel of 25 cm per hr. Details of the growing procedure are given in Ref. 1. The zoned cobalt rods had the following analysis:

Jan 1, 1963

By William C. Brice

Minnesota is involved in planning controversies related to taconite and potential copper-nickel mining. Mine facility planning includes the Reserve dining on-land tailings disposal issue and the potential for a new copper-nickel mining district. Both provide a unique opportunity for innovative planning in the attempt to be responsive to public and private interests. Concerns that emanate as a result of mineral resource activities include environmental protection, land use competition, land exchanges, highway and utility extensions, and legal constraints on public or private lands. The purpose of this newly-developed planning approach is to anticipate such issues and provide a rational information base for dealing with them. The result will be a framework plan for guiding public planning, and an impact assessment for reviewing the implications of industrial project proposals. The approach uses a computer-stored resource inventory of natural and cultural information. Geographic data is mapped and entered into a computer storage and retrieval system. This enables systematic analysis of mineral resources along with environmental and land use considerations. Computer mapping describes the relationship of each activity and allows identification of potential conflicts; it also shows geographical extent in the form of statistical compilations. Resource data is being collected and compiled using a standard metric grid (Universal Transverse Mercator). Individual cells are 100 m. squares and represent areas of about 2.5 acres. The study area contains about 145,000 cells. Data inventories are being compiled in 25 natural and cultural resource categories. Geologic variables include Bedrock Geology, Taconite Reserves and Potential Resources, Depth to the Duluth Complex Contact and two soil inventories. Topographic and hydrologic variables include elevation, slope, slope orientation, surface hydrology, and watersheds. There are also 6 biological data variables and 7 land use inventories.

Jan 1, 1977

By Mark J. Klein

An internal-friction profile induced by nitrogen in Cr-35 at. pet Re was studied as a function of nitrogen concentration and heat treatment. From these studies, the solubility of nitrogen in this alloy was deduced. The equilibrium solubility of nitrogen in chromium does not appear to be substantially changed by the addition of 35 at. pet Re to chromium. However the precipitation kinetics of nitrogen from solution are significantly decreased. IT has been found that rhenium has a beneficial effect on the low-temperature ductility of Group VI-A metals. As part of a study to investigate the mechanism of this increased ductility, it was of interest to compare the concentration of interstitials retained in solution in one of these ductile bee alloys with the concentration retained in solution in its base metal. In this regard, a study of the solubility of nitrogen in ductile Cr-35 at. pet Re was selected for this phase of the investigation because the solubility of nitrogen in the base metal, chromium, has been determined over a fairly large temperature span.1-3 In addition, nitrogen is known to have an embrittling effect on chromium,4 but does not appear to have a comparable embrittling effect on Cr-35 at. pet Re.5 The experimental method selected for this study was the measurement of internal friction. This technique allows interstitial-concentration measurements to be made in bee metals that are sensitive to small changes in the concentration of a particular interstitial, even when other interstitials are present. When subjected to a cyclic stress, interstitial atoms in solid solution give rise to an internal-friction peak whose origin is the stress-induced ordering of interstitials into preferred lat- tice sites. These internal-friction peaks signify a dissipation of elastic energy which is greatest when the period of oscillation is comparable with the relaxation time for the attainment of an equilibrium interstitial distribution. For dilute interstitial binary alloys, the height of the internal-friction peak is proportional to the concentration of interstitial atoms in solid solutions. snoek8 has shown that the internal friction, Q-1, may be expressed by the equation where A is the relaxation strength, ? is the angular frequency, and 7 is the relaxation time. The relaxation strength, A, is proportional to the concentration of interstitials taking part in the relaxation if no interaction occurs between solute atoms. Thus values of peak height, which can be determined as a function of temperature, give a measure of the relative concentration of interstitial atoms in solution at various temperatures. If equilibrium has been attained, the peak heights will be proportional to the interstitial solubilities. The constant that relates A to the interstitial concentration can be determined experimentally from peak-height measurements as a function of concentration for specimens of constant crystallographic orientation. When this has been done, Q-1 measurements can be used to determine solubilities according to the equation C - KQ-1 where C is the soluble interstitial concentration and K is a constant that can be experimentally determined. It is possible, however, that lattice imperfections may bind interstitials to certain lattice sites. Internal friction does not measure these interstitial~, but does measure interstitials which are free to move in the normal lattice sites when subjected to an applied oscillating stress. On alloying the pure metal with a substitutional

Jan 1, 1965

By Raymond Mancha

THE purpose of the Coal Division's Committee on Ventilation is to cover one principal aspect of mine ventilation thoroughly each year, instead of attempting to touch upon several different subjects. The Committee for 1943 consists of four members besides the Chairman. Members, selected because of both knowledge of the current topic of mine ventilation, and diversity of occupation, are: Carel Robinson, consulting engineer with an operating background; T. G. Fear, chief engineer for the Hanna Coal Co., an operator of varied experience in mine ventilation; E. H. Denny, chief of the coal mine inspection division of the U. S. Bureau of Mines, obviously well qualified; and C. M. Smith, editor of Mechanization with a background of mine ventilation study as a member of the mining department of the University of Illinois, at present retained as a ventilation consultant by the Climax. Molybdenum Co. of Climax, Colo.

Jan 1, 1944

By Y. J. Wang

A graphical technique by which the operating points for a two-fan ventilation system can be represented as the intersection of the modified fan curves is described. In constructing the diagram, the air quantities associated with the fans are considered to be independent variables and used as the axes of a rectangular coordinate system. The diagram may include, in addition to the modified fan curves, contour lines for resistances, pressures, and air powers. Procedures for drawing the diagram are discussed and illustrated with an example of the ventilation system.

Jan 1, 1986

By J. Menashi, D. A. Douglas, A. S. Rappas

Aqueous solutions of Na2Cr04 are reduced with CO to produce hydrous Cr2O3 and NaHCO3/Na2CO3. CH3OH, HCOO- and HCHO in the presence of CO2 also reduce Cr(VI) and yield similar products. It is shown that the rate of Cr(VI) reduction can be represented by the expression -d [Cr(VI) ]/dt = k[Cr(VI)]0.5[R], where [R] is the aqueous phase concentration of CH3OH, HCOO- or CO. With these three reductants, the activation energies for the reduction processes are comparable and are of the order of 100 kJ/mol (43,000 Btu per lb mol). Rapid reduction rates are attained at temperatures in excess of 220°C (428°F). With these three reductants, a green acid-insoluble readily filterable hydrous Cr203, is formed. With HCHO, significant reduction of Cr(VI) occurs at about 80° to 100° C (176° to 212° F). The product is an acid-soluble violet modification of hydrous Cr203. Solutions of Na2CrO4 contaminated with Mo(VI) and W(VI) can be reduced to yield a Cr2O3 product with significantly reduced contaminant levels.

Jan 1, 1986

By Nathaniel Arbiter

THE separation of minerals by flotation can be regarded as a rate process, with the extraction of any one mineral determined by its flotation rate, and the grade of concentrate by the relative rates for all the minerals. So regarded, the significant variables for the process are those that control the rates. These variables are of two types, the first describing the ore and its physical and chemical treatment prior to flotation and the second characterizing the separation process in the cells. This paper will examine the variation in rates for a group of separations, will show that a simple rate law appears to govern, and will consider the relation of the control variables to the rates. The use of rate constants for evaluation of performance and efficiency will be discussed. Flotation involves the selective levitation of mineral and its transfer from cell to launder. The flotation rate is the rate of this transfer. It may be defined by the slope of a recovery-time curve for any cell in a bank, or at any time in batch operation. The objective in flotation rate study is an equation expressing the rate in terms of some measurable property of the pulp. This can be either the concentration of floatable mineral in weight per unit volume1,2 or a relative concentration, which will be a function of the recovery." A rate equation for an actual flotation pulp will contain at least two constants, both to be determined from the data. One of these, the initial concentration or proportion of floatable mineral, is not necessarily equal to the feed assay because of nonfloatable oversize or locked particles." The other, a rate constant, is a measure of proportionality between the rate and the pulp property on which the rate depends. The value of the rate constant will be determined by the values of all variables which control the process and will be changed by significant changes in any of them. It is, therefore, a direct measure of performance. Where recovery or grade change continuously with flotation time, the rate constant will be independent of time and will characterize the entire course of the separation. Development of Rate Equations Rate equations can be developed either by analysis of the mechanism of the process or by direct fitting of equations to recovery-time data. Sutherland's attempt by the first method' suggests that the effect of particle size variation on the rate complicates the derivation of a simple equation applicable to an ore pulp. A further problem with an ore is the concentrate grade requirement, which usually involves a variable rate of froth removal. Thus the final rate for any cell may depend on the froth character and froth height, as well as on the pulp composition. This does not imply that each cell cannot reach a steady state2 in which the rate will depend ultimately on pulp composition. The second method is the fitting of rate equations consistent with the necessary boundary conditions* to experimental recovery-time curves. On the assumption that under constant operating conditions the flotation rate is proportional to the actual or relative concentration of floatable mineral in the pulp, a generalized rate equation may be expressed as follows: Rate = Kcn [I] where K is the rate constant, c is some measure of the quantity of floatable mineral in the pulp at time t, and n is a positive number. In previous rate studies, the value of n has been taken as 1, either by direct assumption," or as a result of the hypothesis that bubble-particle collision is rate determining.' A first order equation results, which after integration in terms of cumulative recovery R, leads to Loge A/A-R = Kt [2] The quantity A is the maximum possible recovery with prolonged time under the conditions used. No conclusive proof for the validity of this equation in flotation has been advanced. The evidence cited in its support consists entirely in the demonstration that it appears to apply to a limited number of recovery-time curves."' It will be shown subsequently that this procedure is not sufficient to establish the order of a flotation rate equation. The possibility that the equation may be of higher order therefore requires examination. If, in particular, the exponent in eq 1 is assumed to be 2, then after integration there results R = A2Kt/1 + AKt [3] with K again a rate constant and A the maximum proportion of recoverable mineral. Eq 3 may be

Jan 1, 1952

By G. H. Miller

With the recent advances which have been made in science and technology and the increased use of mathematics in this area, the question of the best mathematics courses for a mining engineer to take is of major importance. The question becomes even more difficult to answer due to the recent increase in the number of different mathematics courses in the last two decades offered by the mathematics departments. Therefore, the National Study of Mathematics Requirements for Scientists and Engineers (NSMRSE) was designed to provide some answers to these questions. Approximately 10,000 scientists and engineers were selected for the Study, These individuals were placed in two categories: (1) The Awards Group, recipients of national honors or awards and those recommended by the members of the Board of Advisors as having national and international reputations in their areas of specialization and (2) The Abstracts Group, persons exceptionally productive in their research, based on the number of journal articles listed in the last five years in the Engineering Index, Scientific and Technological Aerospace Reports, Chemical Abstracts, Biological Abstracts, and the Physics Abstracts. The NSMRSE Course Recommendation Form and the Instruction and Course Content Sheet were constructed with the aid of the Board of Advisors and other consultants. For the Study, 40 courses were selected by the mathematical consultants. In order to make sure that the basic content of the mathematics courses was the same for all respondents, a brief resume of each of the 40 courses was given. The NSMRSE Course Recommendation Form consisted of seven sections. These sections were as follows: Section 1, 38 different specializations; Section 2, orientation of work (applied through theoretical); Section 3, highest degree obtained; Section 4, place of employment (academic, nonacademic); Section 5, administrative capacity (administrative or nonadministrative); Section 6, age groups (five-year intervals). Section 7 contained the 40 courses which were to be marked according to five categories: (1) Course Length, 3 to 36 weeks; (2) Applied-Theoretical Orientation, a five-point scale; (3) Course Level, freshman through graduate; (4) Knowledge of Course; and (5) Use of Course Content in Work. The Analysis The report of the data is based on the replies received from 44 mining engineers. This group was part of the Awards and Abstracts Group for all engineers. The resume of the recommended courses is reported in quintiles (upper fifth to lower fifth), since recommendations of this kind are not precise. The results of the Study are based on recommendations of the most active research men in engineering in the U.S. today; therefore, the reader should realize that these course recommendations represent an upper bound of mathematics requirements for the Ph.D. in both undergraduate and graduate work. Conclusions and Recommendations 1) Mining engineering students who plan to be active research specialists should take all those courses which are "very highly recommended" (80-10070) and "highly recommended" (60-79.9%). Those courses in the upper two quintiles and recommended by most mining engineers are: first-year calculus, third-semester calculus, elementary differential equations, applied statistics, and machine computation. Courses of "moderate recommendation" (40-59.9%) are: vectors, intermediate ordinary differential equations, the first course in partial differential equations, elementary probability, and linear programming. 2) The great majority of mining engineers indicated that they prefer a course which is concerned primarily with applications. Only the standard courses such as first-year college mathematics, calculus, differential equations, and advanced calculus received a recommendation for 50% theory and 50% practice. Therefore, all mathematics courses given to mining engineers should contain many applications and little theory. Engineers in both the applied and the combination (ap-plied-theoretical) groups indicated a definite need for applications in all courses. 3) In general, recommendations were for mathematics courses to be given for short intervals of time such as 3, 6, or 12 weeks. Only the standard courses mentioned previously received the usual one-semester or one-year recommendation. Therefore, it is of value to combine several related courses into a one or two-semester course so that the mining engineering student could acquire important mathematical knowledge at an early date in order to prepare him for his research. 4) There was little use for the newer courses in modern mathematics such as the functional analysis sequence, the modern algebra sequence, and the group theory sequence. In addition, there were uniformly very low recommendations (0-19.9%) for multilinear algebra, complex variables, mathematical logic, special functions, integral equations, approximation theory, analytic mechanics, integral transforms, and geometric algebra. Therefore, these courses should be given a low priority. 5a) Comparisons among mining engineers with different backgrounds showed that the combination ap-plied-theoretical group recommended more mathematics than the applied group. 5b) There was little difference in recommendations between the administrative group and the nonadminis-trative group. 5c) Analysis of age groups showed that those in the lower age groups gave significantly higher recommendations to courses such as the first course in partial dif-

Jan 1, 1971

By Robert L. Russell, Henry W. Zimmerman

The Bunker Hill mine in the Coeur d'Alene mining district at Kellogg, Idaho, has been a major producer of Pb-Ag-Zn ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones and now covers an area approximately 1 mi long by 0.5 mi wide. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Ore production is presently at the rate of about 1700 tpd. A 2-mi adit, the Kellogg tunnel, at the 2500 elevation provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft. 50º-inclined shaft extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for main line track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical ft apart. Also, many intermediate levels exist throughout the mine.

Jan 1, 1971

By F. D. Weeks

THE Salida smelting plant, owned by the Ohio & Colorado Smelting & Refining Co., is situated at an altitude of 7,000 ft., about 2 miles west of Salida, Colo., and 215 miles southwest of Denver. Salida is a division point on the. Denver & Rio Grande R. R. where the narrow-gauge line serving the Sari Juan region joins the through standard gauge. This narrow-gauge road also serves the coal and coke companies at Crested Butte and the lime quarries and mines at Monarch and Garfield, which are only 20 miles distant. These facts, together with the possibility of an appropriate site, doubtless influenced the builders to locate at this point. The smelting plant and yard occupy 80 acres of land on the northeast side of the Arkansas River. The slope of the ground is such as to permit of the ore being delivered by cars at a point 25 ft. above the feed floor; and in front of the furnaces there is a fall of 50 ft. for the slag clump. A recent purchase of river bottom has provided slag room for 20 years. As originally constructed, the plant consisted of four blast furnaces, 40 by 144 in. at tuyeres, two copper-matting furnaces, dust chamber, stack, power plant, blowers, sampling works, and one railroad trestle about 16 ft. from bed floor to rails. Later 12 hand roasters of excellent design were added and the practice of smelting leady matte in-a copper-matting furnace was abandoned. Since the plant passed under the present management the equipment has been increased so that the following is a brief description of the same at this date: Two lead blast. furnaces, 48 by 180 in. at tuyeres, 17 ft. 6 in. tuyères to feed floor; four lead blast furnaces, 40 by 144 in. at tuyères, 17 ft. 6 in. tuyères to feed floor; two copper-matting furnaces, not used; blast-furnace flue, 900 ft.; area 245 sq. ft.; blast-furnace stack, 150 ft.; above furnace floor, 190 ft. When smelting a 500-ton charge per day, the gases approximate 63,700 cu. ft. per minute and travel at a speed of 260 ft. per minute.

Jan 8, 1915

By N. Tiner

In an article on magnesium and its alloys, Gann and Winston! stated that manganese has a limited solubility in the liquid state. W. Schmidt2 showed a diagram according to Joseph Ruhrmann indicating that the solubility of manganese in liquid magnesium falls from about 2.65 per cent at 790°C. to about 0.5 per cent at 675°C. The curve was extrapolated to show zero solubility at the melting point of pure magnesium (Fig. I). This work suggested that at the lowest manganese contents it was not possible to detect either a eutectic or the formation of a solid solution, so that manganese was stated to be present in the structure as large individual crystals. Two years after the presentation of, these results, Gann3 brought evidence to show that some manganese is capable of dissolving to form a solid solution, any excess of manganese present then assuming chiefly the form of small blue-gray particles scattered throughout the primary magnesium crystals, occasionally in clusters but seldom at the boundaries. He presented micrographs of cast alloys containing 0.1, 0.4 and 1.0 per cent manganese that show a small amount of coring around the individual particles due to solid solution, and indicate that the location of the manganese particles is closely associated with the original dendritic structure of the primary crystallization. He also pointed out that the amount of manganese that can be dissolved in magnesium depends on the amount of other alloying elements present, the effect of the second alloying element being to decrease the amount of manganese retained in the alloy. E. Schmid and G. Siebe14 have determined the solid solubility of manganese and its variation with temperature by means of precision X-ray diffraction measurements. They found that the solubility is 3.4 per cent at 645°C. and decreases to practically zero at 200°C. It is apparent that the X-ray diffraction measurements of Schmid and Siebel are not in agreement with the results of Ruhrmann as presented by Schmidt. This disagreement, and also the lack of data on magnesium-aluminum-manganese and magnesium-zinc-manganese systems, led the author to the present investigation, to determine accurately the liquid solubility of manganese and its variation with temperature. Experimental Method The experimental method for making solubility determinations consists of saturating the molten magnesium or the alloys with manganese at various temperatures and analyzing the dip samples taken from these melts. Melting is carried out in a cylindrical steel pot heated by an electric resistance furnace. The pot had a metallic outside coating to protect the steel against oxidation, and a graphite inside lining to prevent the contamination of the melt by prolonged contact with iron. The inside diameter of the pot was 4 in. and the depth 12 inches.

Jan 1, 1945