Search Documents

THE developments in construction and operation of the basic open-hearth furnace that have taken place in recent years have placed new emphasis on the vital influence played by regulation and control of the combustion system in both furnace production and furnace life. The several factors influencing flame development, such as regulation of fuel supply, air supply, air preheat, furnace draft, and furnace reversal, must be controlled closely if successful furnace performance is to be accomplished. Rugged instrumentation of distinctive design is required to sup- ply dependable information concerning operating conditions, which is requisite to proper regulation of combustion. This chapter attempts to give a practical discussion of the various features of open-hearth practice and instrumentation related to the efficient heating of the furnace, control of temperature, and protection of the furnace structure from accidental overheating. The appended references will be helpful to readers wanting a more detailed treatment of individual topics. OPEN-HEARTH FUELS The most important open-hearth fuels are listed in Table 4-1 together with their compositions and other data useful for combustion calculations. A detailed discussion of open-hearth fuels is not attempted here, but certain factors peculiar to their application to this type of process are briefly indicated on the following pages. Very often an open-hearth shop is forced by economic factors to use a fuel to which its furnaces are not very well adapted, because the general fuel-allocation scheme for the works as a whole seems to demand it. Often a variable marginal supply of coke-oven gas or tar must be consumed by the open hearth, together with another fuel such as producer gas, natural gas, or oil, to fill out total requirements. Most furnaces employ more than one kind of fuel during their useful life; however, the partial redesign

Jan 1, 1964

By Robert Leach

THIS paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in commercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordan,4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. ANALYSIS OF STERLING SILVER Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same analysis as our sterling. The first authentic record of the establishment of a standard alloy is during the reign of Henry II in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

Jan 1, 1928

By E. H. Citron

CLEANING fine coal in jigs is not new in Europe, where the feldspar jig is being used almost exclusively for this purpose. A feldspar jig operates with an artificial bed made up generally of feldspar or other hard rock material. Dimensions and specific gravity of this material must be of suitable values for good bedding qualities. For good efficiency, the size should range between 1x2 in. and 2x2x1/2 in. thick.

Jan 4, 1958

By E. Tulcanaza

The practical significance of the in situ grade variability is usually neglected. Although recognized, often times it is either ignored or just considered as a vague guideline in many of the decisions dealing with exploration, reserve estimation, and mine planning. This paper stresses the significance of grade variability for exploration and mining, and illustrates its liaison to the structural features of the ore deposits, as well as to the mining parameters used for mine extraction. Some geostatistical results obtained from a silver mine, tungsten mine, and copper mine in South America are discussed.

Jan 1, 1985

THE developments in construction and operation of the basic open-hearth furnace that have taken place in recent years have placed new emphasis on the vital influence played by regulation and control of the combustion system in both furnace production and furnace life. The several factors influencing flame development, such as regulation of fuel supply, air supply, air preheat, furnace draft, and furnace reversal, must be controlled closely if successful furnace performance is to be accomplished. Rugged instrumentation of distinctive design is required to supply dependable information concerning operating conditions, which is requisite to proper regulation of combustion. This chapter attempts to give a practical discussion of the various features of open-hearth practice and instrumentation related to the efficient heating of the furnace, control of temperature, and protection of the furnace structure from accidental overheating. The appended references will be helpful to readers wanting a more detailed treatment of individual topics. OPEN-HEARTH FUELS The most important open-hearth fuels are listed in Table 4-1 together with their compositions and other data useful for combustion calculations. A detailed discussion of open-hearth fuels is not attempted here, but certain factors peculiar to their application to this type of process are briefly indicated on the following pages. Very often an open-hearth shop is forced by economic factors to use a fuel to which its furnaces are not very well adapted, because the general fuel-allocation scheme for the works as a whole seems to demand it. Often a variable marginal supply of coke-oven gas or tar must be consumed by the open hearth, together with another fuel such as producer gas, natural gas, or oil, to fill out total requirements. Most furnaces employ more than one kind of fuel during their usefu1 life; however, the partial redesign

Jan 1, 1951

By Robert H. Leach, C. H. Chatfield

THIS paper gives a brief summary of the process of manufacture of sterling silver, and some of its more important physical properties, as observed in commercial production of rolled sheet and wire. Although papers have been published by Turner and Smith,1 Rose,2 Sperry3 and Jordan,4 there are few technical data available, and unfortunately the time allowed for the preparation of this paper has not been sufficient to make it as comprehensive as the title might indicate. ANALYSIS OF STERLING SILVER Fine or pure silver is too soft for coinage and the manufacture of articles in which strength and resistance to wear are desired. From the earliest times of which we have record, copper has been the metal generally used to harden silver. Analyses of coins and silver articles from ancient tombs show varying amounts of copper, and old Roman silver objects in the British Museum have approximately the same analysis as our sterling. The first authentic record of the establishment of a stand¬ard alloy is during the reign of Henry II in England. During the twelfth and thirteenth centuries, the people in the Eastern Provinces of Germany had a reputation for the standard and purity of their silver coinage, and it is said that Henry II employed some of these Easterlings, as they were called, to improve and standardize the English coinage, which had become debased. The peculiar standard adopted is probably accounted for by the system of weights used. A troy pound contains

Jan 1, 1928

By S. Ito, Y. Watanabe

In the long range production planning at the Matsumine mine, a management target is to maintain a desired production rate and to keep fluctuations in copper and zinc grades within given allowable limits. A simulation model was developed to find, on a trial and error basis, how feasible and practical the target may be under certain constraints on the underground mining sequence. A number of simulation runs have been made to obtain the most suitable production rate for the long term. In this paper, an outline of the simulation model is described.

Jan 1, 1976

By J. Leja, J. H. Schulman

FROTH flotation is usually effected by the addition of a collector agent and a frothing agent to an aqueous suspension of suitably comminuted mineral ores. The action of collectors is to adsorb onto the surfaces of minerals to be separated, sensitizing them to bubble adherence. The action of frothers has, in the past, been accepted as that of froth formation only, brought about by a lowering of the air/water interfacial tension. Substances capable of producing froth are classed1a,b according to their relative capacities for production of froth-volume and froth stability in the simple frother-water system. The purpose of this paper is to show that the surface active agents acting as frothers become effective only when there is a suitable degree of molecular interaction taking place between collector molecules and frother molecules at the air/water and solid/ water interfaces. Further, the discussion will demonstrate that the actual mechanism of adherence of an air bubble to a suitably collector-coated particle is due to the molecular interaction collector-frother. This leads to the formation of a continuous interfacial film of associated molecules, anchored to the mineral by polar groups of the collector, and enveloping the whole bubble. The tenacity of adhesion mineral-to-bubble results from the strength and the visco-elasticity of this mixed film.

Jan 2, 1954

By O. W. Walvoord

Mill design of the past will not necessarily dictate mill design of the future. There have been many advances and changes in the last few decades, many of which have been extensive and remarkable. Almost certainly, there will be still greater changes in the near future. Minerals beneficiation, for example, as it relates to future mill design, is likely to experience the greatest progress. Gravity separation, though one of the older arts, is in a continuous state of refinement. Flotation, having celebrated its 50th anniversary in 1961, has yet to be surpassed in its contribution to the art of mineral dressing. Ion-exchange, too, will flourish.

Jan 1, 1971

By B. E. Cornish

Most technical and statistical data published on pyrophyllite relating to production figures, uses, markets and sales, have in the past traditionally linked the mineral with talc and soapstone. This is due to several common superficial physical properties resulting in substitute uses and applications. However, these minerals are not similar in chemical composition and do not generally occur in a similar geological environment. Pyrophyllite now stands on its own in the marketplace-particularly in ceramic applications-due to the combination of excellent heat shock and creep resistance properties of the mineral. The increase in pyrophyllite use in the field of ceramics indicates the continuing realization of these marked unique properties. Several new fields of ceramic applications, previously the preserve of high-alumina materials, have been developed on the intrinsic properties of pyrophyllite. Pyrophyllite is an aluminum silicate with the molecular formula of AI2O34SiO2H2O. It would be more appropriate to group pyrophyllite with such materials as kyanite, diaspore, andalusite, and certain high-alumina clays in relation to its general applications (Stuckey, 1928). These materials all have good beat shock resistance properties at high temperatures and are widely used for the manufacture of refractories. For those reasons they are interchangeable in some applications. Pyrophyllite also has many uses in nonceramic applications, the most important to date being as a substitute for talc in fillers. The major pyrophyllite mining operations are located in the US, Japan, Korea, Canada, and Australia, where the mineral is widely used as a raw material for general ceramic, mineral filler, and dilutant applications. Commercial Applications Pyrophyllite was first used in the last century for lining stoves and fireplaces, and also in the carving and polishing of ornamental objects. The rise in industrial demand for new products and applications resulted in the introduction of pyrophyllite as an alternative, mainly for talc and soapstone. Industrial filler applications followed for paint, paper, cosmetics, rubber, pesticides, crayons and pencils, and bleaching soap. The first use of pyrophyllite in ceramic applications was prior to World War II, in the manufacture of ceramic cladding tiles in the US. This was followed by the production of kiln furniture refractories and whiteware when pyrophyllite was offered by suppliers in North Carolina as an alternative to some local clays. The largest tonnages of pyrophyllite used today are in refractory linings in steel ladles in Japan, as seen in Table 1. The consumption of pyrophyllite in Japan is second only to clay and chamotte among refractory raw materials used. Recently this technology has been adopted in Australia. Japanese and Australian practice has resulted in appreciable technical and economic benefits, particularly when pyrophyllite is used in combination with zircon. The potential growth for this application is substantial if US and European steelmakers follow. Investigation and research into the properties of pyrophyllite determined the following main advantages of pyrophyllite-based ceramics: high corrosion resistance for molten iron, steel, and slags; good heat shock resistance; good indices of deformation under load and hot creep resistance (refractories); and increase in mechanical strength of whiteware products promoted by a better distribution of mullite in finished products (also obtained at lower firing temperatures than normally required in production of triaxial ceramics). White cement

Jan 1, 1983

By Richard S. McCaffery

A Research on iron blast-furnace slags has been in progress since 1922 in the metallurgical department of the University of Wisconsin, supplemented by observations, tests and critical examination of operating records at 10 furnaces. From the data thus collected information has been put into forms suitable for use by furnace operators and is given in this report and the three accompanying papers.' In the viscosity results reported, it is estimated that temperatures were measured within 5" C. and that the viscosity determination of the particular slag investigated is accurate within ± 4 per cent. In the viscosity diagrams in the various papers, the equal viscosity lines were drawn in such a manner that in all cases they are located correctly with respect to the actual experimental results, but when determining a viscosity for a particular composition from the diagrams, the viscosity may. be slightly less accurate than the experimentally determined viscosity for the same slag, for the reason that the iso-vis lines interpolated between the experimental results may be shifted slightly without violation of the experimental data. The viscosity diagrams represent our judgment of their position under the above conditions, and we believe the relative accuracy of viscosity data taken from the diagrams is more than sufficient for any use to which the data may be put. Hundreds of samples of slags synthetically produced in the laboratory and of actual furnace slags have been studied in various ways. The ranges of compositions of slags used for viscosity measurements are: silica 25 to 55 per cent.; alumina 0 to 35 per cent.; lime 25 to 55 per cent.; magnesia 0 to 20 per cent. These measurements were made at temperatures of 1250°, 1300°, 1350°, 1400°, 1450°, 1500°, 1550°, 1600" and 1650" Centigrade. Descriptions of apparatus, methods used and statements of the problems investigated have been published in the papers listed in the bibliography beginning on page 120.

Jan 1, 1932

C. H. WILSON,* New York, N. Y. (written discussion?).-On page 2680, under the heading Junction Box and Zone Box, the authors say, with reference to the zone-box principle of connections between primary couple, compensator couple, and copper leads, which method in its appli-cation to a single couple is shown in Fig. 34, that if this principle is adopted for a multiple installation, so as to save compensating leads; a selective switch may be (and the inference is that it must be) inserted between the zone box and the different couples, putting the switch at an inconvenient point, or putting up with some complicated interlacing of connections.. Wilson-Maeulen Co. has employed the zone-box method extensively for several years and in none of the many multiple installa-tions has either of those alternatives been resorted to. Instead there has been used a method of wiring with the switch at the indicator and involv-ing no more complications than the junction-box method shown III

Jan 11, 1919

By H. L. James

THIS paper presents the results and analysis of field trials of various magnetic instruments over anomalies ranging from 20 to 5000 gammas of vertical intensity. The following instruments were used: Askania vertical magnetometer, Wolfson vertical magnetometer (model M-I), Hotchkiss Superdips (used both parallel to and normal to the magnetic meridian, with several settings of the "sigma" angle), Lake Superior dip needle, and the dipping circle for measurements of inclination. The change in inclination over the measured anomalies ranged up to 4°; this caused pronounced changes in sensitivity of the Hotchkiss Superdip oriented parallel to the magnetic meridian. The variable sensitivity not only gives apparent displacement of crests of anomalies, particularly at high sensitivities, but also makes the data difficult or impossible to use in preparation of iso-anomaly maps. This weakness in field performance of the Superdip is shown to be eliminated by orienting the instrument normal to the magnetic meridian and measuring vertical intensity only, which in the latitude of upper Michigan is equal to 97 pct of the total intensity. The dip needle is seen to be relatively ineffectual for location of anomalies of less than 400 gammas.

Jan 1, 1947

By H. C. Juvkam-Wold

The aquifer depressurization system uses a number of wells surrounding a mine shaft to reduce the aquifer pressure in the vicinity of the shaft. The effect of various parameters such as number of wells, wellbore diameter, time, and well location is discussed. It is concluded that, with a properly designed depressurization system, the aquifer pressure and the water inflow rate to the shaft may be reduced to less than 15% of their potential values in the absence of wells.

Jan 1, 1983

By James R. Garvey

Coal reserves of the United States are enormous. Considered on the basis of proven reserves, and compared with reserves of other fuels, coal constitutes 88% of the proven recoverable energy resources of the nation. That includes oil, natural gas, oil shale and uranium used in burner reactors. Considered on the basis of "ultimate recoverable reserves", that is, those resources which can be extracted with improved technology and at somewhat higher costs and including those resources of all fuels not yet found but believed to be waiting discovery, coal still accounts for 75 % of the national total. In the U.S. hydrocarbon economy about 76% of the total energy needs are supplied by petroleum and natural gas and about 20% by coal. Domestic resources of oil and gas are running dangerously low, and assuming a continued hydrocarbon economy, the 20% supplied by coal may increase dramatically. Nearly a quarter of the petroleum consumed in the U.S. is imported. Natural gas is in shorter supply than petroleum and the problems of its importation seem at least as difficult as those of oil.

Jan 6, 1972

By H. Colijn

Belt scales are frequently used in the mining industry because of the ability to handle large tonnages without interrupting the material flow, fitting easily into all types of bulk handling systems and being relatively inexpensive. Although manufacturers claim weighing accuracies better than Y2%, many operators experience, in practice, much larger errors and they have become apprehensive about the use of belt scales. However, in spite of these disappointing instances, a belt scale is one of the most valuable tools for process and inventory control. Since it is a measuring device, care should be given to the design and installation of belt scales. The basic components of a belt scale are: (1) conveyor belt, (2) scale suspension, (3) sensing device, (4) integrating and recording. The first component of this system is of great importance to the overall accuracy and has been thoroughly discussed in earlier papers. This paper will review primarily the various scale hardware designs currently available, and will be confined to the last three components of the system.

Jan 1, 1973

By William G. Schultz

Sylvite of Canada, a division of Hudson Bay Mining and Smelting Co., operates a new 8500-tpd potash mine ten miles northeast of Rocanville, Sask. This mine, employing less than 60 men in its underground maintenance, engineering, and production operations probably ranks as one of the most highly mechanized and automated mining operations in the world. Access to the flat lying potash bed is through two 16-ft-diam concrete and steel lined shafts 3300 ft deep. The backbone of the operation is two 258-ton, 1500-hp continuous mining machines capable of mining in excess of 700 tph per machine while employing extensible conveyors for haulage. This production capability is complemented by a completely automated haulage, storage, and hoisting system. Of the other unique features of this operation, the principal ones are that the mine was designed and developed by the people that are currently operating it and from the time the shafts were commissioned, the mine was completely developed, equipped, and brought to full production in less than six months.

Jan 1, 1974

By Cleland N. Conwell

APPLICATION of seismic methods to the location of buried channels in placer mining is fairly common knowledge, yet some of the facets of seismic refraction surveys have remained obscure in their application to mining. This description by a member of the U. S. Bureau of Reclamation team investigating bedrock at the Oso Dam site, may offer a lead to wider application of the method for bedrock determinations in engineering of mine and mill plants, tailing disposal, and water supply. It may also offer assistance in planning geological exploration in areas covered by overburden. Pertinent, and perhaps more than passingly significant, is that the seismic survey of the Oso dam site started at noon and was completed the afternoon of the next day. Location Oso dam site is on the Navajo River, Archuleta, County, Colo., 30 miles southeast of Pagosa Springs, Colo., 10 miles northwest of Chama, N. M. Bedrock at the proposed dam site is Mesa Verde Formation, Cretaceous age sandstone. The nearest good sandstone exposure is about 5/8 of a mile upstream from the location of the seismic determinations. The material above bedrock is sand and gravel with sandy loam soil covering benches above the river. The site appeared favorable, after a geologic and topographic reconnaissance, but overburden thickness was unknown. Exploratory drilling was not contemplated in the near future so a short seismic investigation was selected as the most suitable method of determining depth to bedrock. Field Procedure Geophysically, a seismic depth investigation is simply the measurement of depth from ground surface to the top of a layer which transmits seismic waves at a higher velocity. In this case the high-velocity seismic layer tentatively correlates with the Mesa Verde sandstone. Field procedure required a seismic explorationline or "spread" with 12 geophones set at measured intervals. Explosive charges were buried at few feet in the ground and detonated at shotpoints near the ends of the spread, and at intermediate points. The time of travel of the seismic waves from the shotpoints through the ground to each of the geophones along the spread was measured and recorded photographically with equipment housed in a field truck. The seismograph on each spread provided a time-travel graph. From it were computed the speed of seismic waves in various layers below the surface and depth to each different seismic layer below the shotpoint. In the case of the Oso dam site it was possible, in addition, to determine the depths below certain geophones, because there were only two seismic layers involved. Interpretation In seismic exploration waves are refracted from the top of layers which often correspond to divisions between subsurface formations. When drill holes are available the geologic logs offer a means of correlating stratigraphic breaks with seismic layers, improving reliability of seismic interpretation in terms of depth to bedrock or other geologic terms. There were no drill holes available in the case of the work at the Oso dam site. Geologic conditions appeared favorable for seismic technique because of excellent contrast in seismic wave velocity between the overburden and the Mesa Verde formation. The upper layer had a velocity of approximately 2500 fps and was interpreted as overburden, the lower layer had a velocity of approximately 9000 fps and was assumed to be the sandstone. These velocities are of the order expected in these materials. The seismographs obtained at the Oso dam site were excellent. The energy from the shot came in strongly at each geophone, giving an easily read record. Time-travel graphs plotted from wave arrival times were uniform and made interpretation comparatively easy. In Spreads 1 and 2 near the river the lower velocity layer was 12 to 15 ft deep. For the spreads on higher ground, or the bench south of the river, it was from 15 to 29 ft deep.

Jan 1, 1952

Professor Somasundaran has given an excellent presentation of the numerous problems which remain to be solved before the selective aggregation of fine particulates is likely to see broad commercial application in the beneficiation of mineral fines. However it is useful, I think, to reiterate some of the major problem areas. The over-riding factor which has limited the development of selective aggregation techniques is that processes such as coagulation and flocculation tend to be inherently non-selective. Conditions which favor the aggregation of one kind of fine particles usually favor the aggregation of all kinds of particles. As Professor Somasundaran has pointed out, the state of aggregation of a fine-particle dispersion is primarily determined by the forces of interaction between the individual particles. In most systems, the dominant forces are: 1. van der Waals - London Dispersion forces between the particles themselves 2. electrical double layer forces 3. steric forces between adsorbed layers on the surfaces of the particles. The London Dispersion forces between like particles are always attractive, but for dissimilar particles dispersed in a fluid medium can, in some cases, lead to a net repulsion. Electrical double layer forces always lead to repulsion between like particles but can, again, cause either attraction or repulsion for dissimilar materials. The steric forces, which are by far the least understood of the three types, can also lead to attraction or repulsion depending on condi-

Jan 1, 1979

By W. Blaschke, E. Malysa

INTRODUCTION In recent years in Poland, a problem connected with the occurrence of a considerable amount of liberated galena grains in size fractions under 1mm has arisen in the zinc-lead processing area. Operating practices have included crushing of ore particles under 0.2 mm followed by flotation. Jigs were applied to separate the concentrates from size fractions under 10 mm and to prevent the galena overgrinding. However, the fractions being too wide, the jigs have not worked effectively, in spite of the great differences in specific gravities of galena, blende and gangue minerals. Fine galena grains move into light fractions in considerable amounts and hence are overground. Therefore, the flotation becomes difficult and galena is lost in its tailings. These losses could be avoided by introducing separation in the grinding and classification circuits. The amount of 0-1 mm fraction is great; therefore, the application of concentrating tables or other kinds of jigs is impossible from an economic point of view. Taking these factors into account, the possibility of application of pinched-sluices was investigated. These are simple devices without moving parts, they have a high output for the unit areas, and their water and energy consumptions are low. In this paper, the results of zinc-lead ores beneficiation in pinched-sluices are presented.

Jan 1, 1980