Search Documents

By M Behrens, A McPhee, B D. Hegan

This paper describes the design and construction of twin 400 m long road tunnels as part of the Northern Motorway Extension Project in Auckland, New Zealand. Construction of the tunnel civil works is now completed and installation of mechanical and electrical systems is well underway. The tunnels are expected to be open for traffic at the end of 2008. The paper will address the design aspects of the project including: tunnel alignment and cross-section, geotechnical conditions and rock support, waterproofing and concrete lining and fire and life safety. The paper will cover the bored tunnel section, the cut-and-cover tunnel section, cross passages and portal structures. The design brief included a requirement for the tunnels to be a gateway to Auckland and this required particular attention to be given to the visual appearance of the finished tunnel structure. The final arrangement of the portal structures and a requirement for recesses in the concrete lining for emergency cabinets, deluge pipework and cable runs, reflects these requirements. The tunnels were excavated by a roadheader and road planer using a heading and bench. Initial support was provided by a combination of lattice girders, cement grouted rock bolts and steel fibre reinforced shotcrete. The permanent lining consisted of installation of a drainage geotextile and waterproof membrane, followed by cast in situ unreinforced concrete. Each portal consists of a cut-and-cover section. This paper describes the tunnel construction methods, including the particular requirements for safety, the environment and community relations. The tunnel is fitted with a compartmentalised deluge system for fire fighting purposes. The tunnel control centre is incorporated into the control centre for Auckland Harbour Bridge, some 30 km from the tunnel location.

Jan 1, 2008

Barrick Gold Granny Smith Mine is currently undergoing conversion from an open cut operation to an underground mine at the Wallaby deposit. The underground project commenced in 2005 with the development of the reserves immediately below the pit and is now currently entering a production ramp-up phase for mining of these two initial surfaces below the pit. With increasing gold prices the owner has been forced to re-evaluate the underground project and has decided to investigate the potential of a deep level mine. This deep level underground mine presents a collection of challenges with the most notable being exploitation of a series of well separated near horizontal lodes ranging in thickness from less than 1 to 20 m. A variety of room and pillar mining methods are employed for extraction with careful consideration to resource recovery and pillar design for long-term stability. Compounding these deep level challenges is a need to accelerate mine level development to maintain the production profile of the mine. This paper describes the challenges, key learnings and outcomes of the studies undertaken to date associated with this project.

Jan 1, 2008

By I M. Platten, Y Xie

Complex gold deposits are generally characterised by variable geometries, strong structural controls on grade distribution and a high-nugget effect. The use of diamond drilling and fire assays in this environment often results in an understatement of grade. Bulk samples are likely to be the closest estimators of true grade, and may be required to evaluate geological/grade risk during resource estimation/feasibility studies. Any bulk sampling program requires appropriate planning and implementation. The planning stage should attempt to delimit the extent and nature of mineralisation; characterise mineralogy and metallurgical properties of the ore; and define bulk sample size and how it will be sampled/processed. The approach to sample processing will be governed by the results of metallurgical testing and geological knowledge. Careful design of sampling protocols must be undertaken through material characterisation, understanding of gold particle sizing and the application of GyÆs Sampling Theory.

Jan 1, 2008

By T Sasaoka, H Shimada

Mined-out limestone/aggregate quarries in Japan contain many high and enormous pit walls. Many precious resources are abandoned in these final pit walls. In addition, there are many mines which are located in or near populated areas in Japan. Utilisationof the potentially useful under- ground space at mined-out sites is a topic relevant to the practice of surface mining. This paper describes and discusses the concept of underground space utilisation and tunnelling systems, referring specifically to geotechnical/ tunnelling parameters.

Jan 1, 2008

By R Grobler, D Burger, L Alberts

The current climate in the mining industry is allowing mining companies to further broaden their views and investigate technologies to improve the safety, efficiency and cost-effectiveness of their operations. Furthermore, underground mine environments will become more demanding for mining equipment and personnel as orebodies become deeper in weaker ground conditions with more extreme environmental conditions. Loading and hauling can represent significant components of the production cycle of an underground mine and automation of these activities can offer considerable benefits. Sandvik has accumulated a long history and experience in loading and hauling automation in underground mining. Since the late 1980s Sandvik has actively participated in several major research and development automation programs leading to the commencement of the development of an integrated system for semiautomated loading in 1999. Development work was later conducted to expand the capabilities of the system for automated hauling during 2001 and the AutoMine« system became commercially available. The first delivery of the AutoMine« system was completed in August 2004 in South America, where the system continues to operate in a full-scale production environment and is being expanded as the production area enlarges. Further systems have been delivered and are operational in North America, Africa and Europe. This paper focuses on the AutoMine« system deployed in Block 4 at De Beers Finsch Mine in South Africa. An overview of the mine and the process used to acquire the system and the key drivers which led to the selection of an automated solution are described. An overview of the initial system installation, subsequent expansions and future plans are presented. This is followed by a summary of the implementation and operational experiences associated with automated underground operations. The paper concludes by summarising the benefits that have been realised.

Jan 1, 2008

By F A. Rosyid

Mineral resources are national assets which must be capitalised for national development. Those assets should be transferred into real economic capital and then into social capital to achieve national/regional prosperity. Successful development in the mining industry will depend on the correctness in determining the role of mining industries for regional development. Using the context of sustainable development, this paper will analyse the concept and process of mining industry development as an accelerator to achieve regional sustainable development, using the mining operations of PT Newmont Nusa Tenggara (PT NNT) in Batuhijau, Sumbawa Barat Regency as a case study. In the premining activity phase, Sumbawa Barat was dependent on the agricultural sector. Agriculture contributed around 40 per cent of the regional gross domestic product (GDP). Meanwhile, in the activity phase, mining became the sector with the biggest contribution to regional economy. From its operation in Batuhijau, PT NNT contributed around 70 per cent of the regional GDP per year since 2001. In year 2000, the GDP had increased 170 per cent from its figure in 1999. However, due to its depleting reserve, PT NNT will finish its activity in Batuhijau by year 2015. Consequently, the Government of Sumbawa Barat Regency must develop other sectors in the post-mining phase to sustain economic development. Based on location quotient (LQ) and input-output analyses, Sumbawa Barat should develop its priority sectors, ie agriculture, trading and hotel, services and construction to achieve sustainability after mining life. Development of these non-mineral sectors is expected to sustain economic growth in the region.

Jan 1, 2008

By M D. Boscardin, P A. Roy

The North Shore Connector Project for the Port Authority of Allegheny County involves TBM tunnelling twin light rail tunnels through cohesive soils and rock under the Allegheny River and a narrow city street. Along the tunnel alignment are a listed historic building on shallow foundations as well as modern buildings on deep foundations; one major office block was actually constructed directly over the alignment during the latter phases of design process. This paper provides an overview of the general site conditions, tunnel design and the technical basis for excavation support and tunnelling decisions. Deformation limits, ground improvement, monitoring and mitigation plans are also discussed. Project construction has now commenced and a brief summary of progress to date is included in this paper; this will be updated for the presentation to be made in Melbourne.

Jan 1, 2008

Different mineral structures can act as mineral reservoirs for the immobilisation of toxic compounds. In the paper different mineral structures will be explained and their potential for incorporation of heavy metals and anions will be shown. The following structures will be explained (P÷llmann, 2007):apatites (incorporation of heavy metals, silicate apatites);ettringites (fixation of oxo-anions);layered double hydroxides (fixation of heavy metals, fixation of anions, fixation of organics, sorption materials); andmanganese oxides. Different possibilities of solid solution and incorporation in crystal structures will be explained and advantages of stable minerals be proved using experiences with real toxic wastes. In the process of thermal treatment the formation of primary mineral reservoirs will be shown. The precursor phases (similar to well known cement minerals) react in contact with water to form secondary mineral reservoirs (cement hydration mineral products). The formation condition of primary and secondary mineral reservoirs and their stabilities and incorporation possibilities will be shown. Examples for incorporation of various elements are given. Application for water clarification will be outlined.

Jan 1, 2008

The discovery of minerals in any community, especially precious minerals, gives a sense of hope and optimism about development prospects within the community. However, the euphoria surrounding such a find could be short lived if the wrong perception is created at the inception of the project, that the exploitation of the mineral resource will pose a serious problem to the community. The socio-economic impact can be negative or positive but if not properly handled, the negatives will outweigh the positives. Illegal mining activity, popularly known as Galamsey in Ghana, is a typical example of the negative impact of the mineral industry. Galamsey activities have resulted in an increase in school drop-out rate, pollution of water bodies affecting entire communities bringing a lot of health problems, destruction of farm lands, destruction of rail lines resulting in transportation problems, armed robbery, prostitution, just to mention a few. The improvement of the water supply system in the surrounding communities, implementation of sustainable development programs, improvement in the infrastructure, are just a few examples of positive socio-economic impact.Factors responsible for the socio-economic and environmental impact include: the unwillingness of most companies to invest substantial resources to deal with environmental issues, lack of adequate professionals with the requisite appreciation for environmental issues related to their activities, realisation that support of surrounding communities is key to successful operations, the now globally accepted view that multinational companies should invest in the socio-economic lives of the surrounding communities, etc. In order to ensure the prevention of the negative impact of mining activities on local communities, there should be a paradigm shift in the way the training for the new crop of mining and metallurgical engineers have been structured in the past, social contract with the local communities must be drawn and implemented; it must not be an imposition on the communities but rather a contract arising out of extensive interactions between the industries and the local communities. Environmental awareness has reached a level where communities affected by the minerals industry, to a very large extent, know what they should tolerate and what they should not. There is therefore the need to ensure that effective systems are in place to exploit mineral resources without damaging the environment.

Jan 1, 2008

By R Lachenicht, J Player, A Thompson, E Villaescusa

Kanowna Belle Gold Mine is a deep, high-stress, sublevel open stoping mine located near Kalgoorlie. Seismic activity during the development cycle presented problems, including concerns regarding the exposure of personnel. A number of seismic management systems were developed and tested to monitor seismicity and control the risk. It was recognised that a dynamically capable reinforcement and support system was required to be installed as part of the development cycle to reduce the risk of exposure of the underground workforce to uncontrolled movement of rock. The performance of a new Garford Dynamically capable bolt was measured in tests performed by the Western Australian School of Mines (WASM) at their Kalgoorlie Dynamic Test Facility. Detailed descriptions of the facility and data processing were reported by Player, Villaescusa and Thompson (2004) and Thompson, Villaescusa and Player (2004). The development of the Garford Dynamic bolt is described and dynamic testing results are presented and evaluated. This bolt was implemented in the mining cycle following the testing program; the observed performance is described and assessed in this paper.  

Jan 1, 2008

Virtual reality (VR) simulators represent a powerful tool for training humans to perform tasks which are otherwise expensive or dangerous to duplicate in the real world. The idea is not new. Flight simulators have been used for decades to train pilots for both commercial and military aviation. These systems have advanced to a point that they are integral to both the design and the operation of modern aircraft (Adams, Klowden and Hannaford, 2001; Mastaglio and Callahan, 1995). This technology has been successfully extended and utilised in the mining industry in a range of successful applications (Bise, 1997; Denby and Schofield, 1999a; Schofield, 2005; Henning et al, 2002; Kaiser, Vasak and Suorineni, 2005). There are a number of lessons that can be learned from other industries that have successfully utilised virtual technology for a number of years. Specific rules of thumb regarding the specification, development, application and operation of these simulators can be garnered from other industrial training systems and examined in a minerals industry context (Tromp and Schofield, 2004; Schofield, 2006). This paper intends to discuss some of these generic rules in the context of a number of recently developed virtual reality mining applications.

Jan 1, 2008

By M English, M Yumlu

At times of high metal prices, mining projects that have previously been put into the ætoo hard basketÆ are now being more closely examined. Typically these projects include the potential recovery of small mineable tonnes with high contained metal values and often with poor ground conditions. For many underground mining projects, the drift and fill method is viewed as a high-cost method and a æmethod of last resortÆ. As a result the method is not well known in Australia and it is the authorsÆ view that the method is under utilised. The drift and fill method can be applied to a variety of underground mining situations and is a preferred method for some orebody geometries and where ore recovery is viewed as a key to project success. This paper examines some of the critical mine planning and backfill issues involved with the drift and fill mining method.

Jan 1, 2008

By S M. C Verryn

Through the application of the Rietveld method, X-ray diffraction analysis has developed into a fully quantitative method for phase analysis of metallurgical products. The Rietveld method itself has progressed from an unstable method that required constant operator intervention to a stable and robust method suited even for routine process control. Knowledge of the crystal structures of the major phases is essential for Rietveld analysis, and these are well known for most minerals and major phases in metallurgical products. It provides the basic structural information necessary for the determination of mineral stoichiometry and for elucidating solid solution behaviour. Modern methods, such as simulated annealing and charge flipping, permits the determination of crystal structures from powder data. Unit cell data can be used where conventional microchemical analysis is unable to provide an answer to the extent of solid solution in ilmenite roasting. Unit cell data (by XRD) is used to determine the amount of roasting necessary for the development of magnetisation to be able to separate chromite from an ilmenite concentrate. Phase quantification is probably the most widely used application of XRD analysis. It is used for materials balance in the minerals and cement industries, and it is finding novel applications in the iron and steel industry. Applications of XRD in high-temperature metallurgical processes are increasing. In this paper the phase chemistry of iron ore sinters, the evaluation of subsolidus reactions in titania slags and the identification of furnace accretions are discussed. Despite the success of the Rietveld method in phase quantification, the method still needs further development in the quantification of closely related or polytypic phases. The quantification of pyrrhotite phases using various Rietveld programs still gives ambiguous results. This is also true for the different SFCA phases in iron ore sinters. Clearly the analysis of similar phases, differing only in the presence of weak superlattice reflections is still problematic.

Jan 1, 2008

By U Rehm

The biggest hard rock double-shield tunnel boring machine (TBM) in the world, with a diameter of 12.4 m, is currently excavating the North-South Bypass, which includes a crossing under the Brisbane River, Brisbane, Australia, to relieve the often congested road traffic in the city centre. Ten years ago a 10.7 m Mixshield giant helped to handle the Olympic Games in Sydney linking the airport with the city centre for an improved transportation of fascinated visitors. In Shanghai, currently the biggest TBM in the world with 15.43 m diameter presents excellent performance rates; and in Paris a convertible Mixshield could be quickly changed from earth pressure balanced (EPB) to slurry type in order to handle the very heterogeneous ground conditions. In Madrid a 15.2 m EPB giant finished its tunnel job four months ahead of schedule. Large-scale TBMs have proved their economic and innovative potential to create the current and future underground architecture of mega-cities. TBM technology has made further large innovative steps in the last decade. State-of-the-art is a TBM for very heterogeneous ground conditions comprising hard and soft rock with additional high groundwater pressure. The machine concept is adapted to the various ground conditions and allows for a quick and flexible application. Ground treatment by means of additives developed to a helpful tool in this connection. To meet the special challenges of urban tunnel projects of nowadays it is of very high importance, beside applying highest developed technology of TBM, to have a comprehensive technical support during the project phase and to develop positive relationships between all participants of the project which last longer than only for one project.

Jan 1, 2008

By P W. Cleary, M D. Sinnott

Cross-belt cutters are commonly used for sampling coal. They are generally cheaper than falling-stream cutters, particularly when a cutter must be retrofitted. The major mechanisms thought most likely to lead to sample bias are being investigated by discrete element modelling (DEM) in a project funded through the Australian Coal Association Research Program. This paper describes a benchmark run and the current direction of research.

Jan 1, 2008

Sample preparation for gold samples, where the distribution and size of gold particles is often irregular, usually demands that a relatively large sample weight is taken to produce a representative sample for analysis. Traditional sample preparation of gold samples incorporated multiple stages of coarse particle size reduction followed by subdivision of the sample prior to final fine pulverising. This technique developed because of the limited equipment options available to laboratories. As a result significant errors are introduced and the final sample size being pulverised is a small fraction of the original sample weight. Three significant developments have occurred in the last 25 years to significantly improve sample preparation of gold samples: 1.  large capacity fine pulverising,2.  fine jaw crushing, and3.  whole sample coarse pulverising. In the mid-1980s an Australian manufacturer developed large capacity pulverising bowls which had the ability to reduce samples with a mass of 1.5 - 3.5 kg to a nominal 0.075 mm product in approximately three to five minutes. Laboratories were able to produce a large homogeneous pulverised sample which significantly reduced the error in sampling. However, exploration and mine samples are usually 7 to 10 kg and the sample requires a subdivision stage following crushing to produce the 3.5 kg for the pulverising step, thus introducing potential for significant error. The development of fine jaw crushing allowed particle size reduction to -2 mm which reduced the subdivision error of the bulk sample prior to fine pulverising. Subdivision of the crushed sample at -2 mm still results in potential sampling errors, where the gold particles are not sufficiently liberated to be representatively sampled. Clearly the best option would be to reduce the particle size small enough to ensure a representative sample prior to final pulverising. Continuous mills offer a partial solution but are relatively slow and subject the sample to differential pulverising prior to subdivision. Clearly this does not provide the best solution for routine laboratory applications where high volumes of samples are to be processed. The recent development of a large capacity coarse pulverising system allows samples of up to 10 kg to be reduced to -0.25 mm prior to subdivision, and fine pulverised to -0.075 mm. Laboratories now have the necessary equipment to perform reliable large capacity sample preparation of gold samples. The exact choice of a sample preparation scheme may still depend on particular ore types but the need for multiple crushing and subdivision stages is redundant.

Jan 1, 2008

The increasing global demand for rough materials forces almost every mine to look at the mechanisation in their processes. This will not onlyimprove performance but with safety issues becoming more and more prevalent, the need for the introduction of mechanisation technologies to mining applications is essential. Ongoing developments are occurring in almost every field, ranging from basic developments to specialised mining. Mechanical tunnelling and shaft sinking have set the standards regarding safety, profitability and environmental protection. Different machine types and working principles have been developed to suit the geological and hydrological requirements of tunnelling projects worldwide. Continuous activity in research and development leads to constant optimisation of tunnelling performance.

Jan 1, 2008

By T Mizuta, H Satoh, M Ogasawara, M Miyata, M Fukuyama

The Miocene Chichibu granitoids associated with the Chichibu skarn deposit are divided into North Body, South Body and Daikoku altered stock. Orebodies of the Chichibu skarn deposit are mainly distributed in the north-western part of the North Body and Daikoku altered stock. The North Body consists of magnetite-series granitoids ranging from tonalite to granodiorite and to monzogranite from the margins to the centre of the intrusion. The South Body consists of tonalite and granodiorite, and most of these rocks are also classified as magnetite-series granitoids. The Daikoku altered stock consists of a quartz diorite porphyry. The SiO2 contents of the granitic rocks of the North Body and South Body range from 61.6 to 70.7 wt per cent. During magmatic differentiation, Cu, As and Zn contents in fresh granitic rocks of the North Body and South Body increase with SiO2 content up to 63 wt per cent SiO2, and then progressively decrease with increasing SiO2 contents as SiO2 exceeds 65 wt per cent. Estimated pressure for the emplacement of the granitoids is about 0.5 kbars. Cathodoluminescence studies on quartz from those granitic rocks show that vapour rich two-phase fluid inclusions tend to occur in the core of quartz crystals, while halite-bearing poly-phase fluid inclusions occur in the margins of quartz crystals. The distribution of fluid inclusions suggests that fluid composition changed from low to high salinities during the growth of magmatic quartz crystals. Texture showing quartz crystals with an oval shape enclosed by radial aggregates of a mixture of fine-grained quartz, plagioclase and K-feldspar composing the groundmass of the monzogranite also suggests a pressure decrease during solidification of North Body. These findings show that high salinity fluids were present during magmatic differentiation and that Fe-Cu-Pb-Zn-Au-Ag skarn mineralisation of the Chichibu deposit was possibly associated with these high salinity fluids. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By G Cormack

By designing comminution circuits for mineral liberation rather than the final recovery process and by using high mass pull gravity recovery, the concept of underground processing has become a reality. Gekko has found that many ores respond favourably to fine crushing with either high pressure grinding rolls or vertical shaft impactors which when combined with the InLine Pressure Jig gravity separator and coarse flotation results in a narrow, low-head, compact processing plant that can be sensibly fitted in existing underground openings. The focus on fine crushing reduces the power requirements of the plant to approximately 5 kWh/t for a capacity of up to 20 t/h run of mine ore feed. The use of water recycle systems places no extra load on the mineÆs normal water handling system. GekkoÆs underground processing plant, the æPythonÆ, has been designed to be towed down the decline or lowered down a shaft and is capable of being installed in sloping, non-linear drives for placement close to the working face. The overall benefit to mining companies of this concept has been estimated to be a significant operating cost-saving, lower cut-off grade and a significantly smaller environmental footprint.

Jan 1, 2008

By M I. Pownceby, W J. Bruckard

A South African chromite sample was subjected to characterisation and physical beneficiation testwork in order to assess its suitability to produce an upgraded chromite product with a silica level of <1 per cent SiO2 and a chromite level of >46 per cent Cr2O3. Chemical analysis by XRF indicated that the bulk material had a Cr2O3 content of 40.5 per cent w/w and a SiO2 content of 7.5 per cent w/w. Combined XRF analysis with sizing data showed that the majority (~70 per cent) of the siliceous material was present in the +600 ¦m fraction while ~70 per cent of the Cr2O3 was in the -600 ¦m fraction. Qualitative mineral phase analysis by XRD indicated that the sample mineralogy was dominated by ferrian-magnesiochromite spinel ([Fe,Mg]Cr2O4) and aluminium-chromite spinel (Fe[Al,Cr]2O4), with enstatite (Mg2Si2O6), haematite (Fe2O3) and anorthite (CaAl2Si2O8) as minor phases. SEM and EMP characterisation showed that the silica was mainly present in discrete enstatite grains but lesser amounts were also present as the high silica phases plagioclase and enstatite on the edge of grains. Wet gravity separation performed on sized fractions (-600+106 ¦m size range) from the -2.0 mm (primary) ore as well as the ore that had been crushed to pass 0.6 mm (secondary) showed that stage crushing of the -2 mm +600 ¦m fraction followed by wet gravity separation upgraded the Cr2O3 grade at 70 per cent Cr2O3 recovery from ~44 per cent Cr2O3 in the primary material to 46 per cent Cr2O3 (the target grade specification) in the secondary sample. It also showed that the stage crushing of this +600 ¦m fraction at a cut-off level of one per cent SiO2 increased the cumulative Cr2O3 recovery from ~50 per cent in the primary material to ~63 per cent in the secondary sample in the same size range of -600+106 ¦m. The extent to which additional crushing could lead to improved chromite recoveries at the required chromite and silica grade target specifications was not determined. This experience demonstrates that prior to processing test work being conducted, a thorough understanding of the chemistry and mineralogy of the test sample promotes efficient and targeted processing research.

Jan 1, 2008