Search Documents

By E J. B van Etten

This paper reports on the results of several years of monitoring rehabilitation at a silica sand mine on the Swan Coastal Plain, south of Perth. Mining here occurs below the regional watertable and leaves a post-mine landscape of dredge pond voids (pit lakes) with surrounding battered slopes. The restoration we recommended was to develop the pit lakes as wetlands of regional analogue and value. Several different restoration techniques have been applied to re-vegetate pit lake slopes over many years which have enabled an evaluation of reasons for success/failure of different restoration approaches. Learning acquired clearly showed the benefits of using fresh topsoil for restoration over topsoil that has been stockpiled for several years. Most topsoil used in restoration was from seasonal wetlands and consequently restoration was most successful in the riparian zone from the edge of pit lakes to about 2 m vertically above the water table. Topsoil restored areas above this level remained poor in plant species and cover. Conversely, remedial seeding/planting proved largely unsuccessful. Permanently and seasonally flooded pit lake margins recolonised relatively quickly and successfully with native sedges and rushes. Development of rehabilitated upper slope plant communities over time was evident with loss of typical wetland species and greater growth and survivorship of upland and dampland plant species on mid to upper rehabilitated slopes. Plant communities of lower slopes showed a converse pattern of development, with a shift towards a more typical wetland composition. We believe matching topsoil to site and development of topographic profiles similar to natural wetlands of the region are the keys to optimising restoration success of sand mines with shallow water tables.

Oct 5, 2011

By D A. Deglon

Solids suspension is important in the design and operation of mechanical flotation cells, and is a necessary precondition to particle collection. Most of the fundamental hydrodynamic research that incorporates some aspect of solids suspension was done by Arbiter, Harris, and co-workers, or Schubert and co-workers. However, a need for research into solids suspension in mechanical flotation cells exists, since very little has been done since the late 1980s; a time that also coincides with the advent of round mechanical flotation cells and the subsequent dramatic increases in maximum flotation cell sizes. In this work, concentration profiles and critical impeller speeds, Njs, were measured in a 0.124 m3, round cell fitted with a 0.150 m, Bateman impeller mechanism. Two solids size fractions (75 - 106 and 150 - 250 ¦m) were tested, in ungassed and gassed conditions (JG = 0, 1 cm/s) and at various impeller speeds (300 - 900 rpm). The effectiveness of solids suspension was quantified in three ways in terms of extent of off-bottom solids suspension, suspension height (extent of solids distribution), and variation within the solids distribution, which together present a complete quantitative picture of solids suspension and distribution within the cell. Consistent trends were found when these effectiveness criteria were considered against relative impeller speed, in terms of percentage of critical impeller speed, N/Njs. Off-bottom solids suspension is complete at or above 100 per cent of Njs, with significant sedimentation occurring as the impeller speed drops below 60 per cent of Njs. Suspension heights consistently reached a level equivalent to 90 per cent of the tank diameter at the critical impeller speed, and dropped off significantly as N/Njs dropped below 60 per cent. The variation in the solids concentrations within the sampled profiles showed consistent trends in two-phase but not under three-phase conditions. The paper concludes that the critical impeller speed, Njs, commonly used in the design and operation of standard stirred tanks, is a very useful solids suspension benchmark for describing all aspects of solids suspension in mechanical flotation cells and should be correlated to system conditions.

Jan 1, 2005

The tangible effects of leakage are presented graphically, and a technique for quantifying the leakage characteristics of a ventilation column using the æSolveÆ capabilities of a common spreadsheet is demonstrated. A case study of a working decline in Western Australia is used to demonstrate the potential for more realistic design of development ventilating systems, and for more cost effective management of the condition of the duct.

Jan 1, 2002

The Mt Keith Mining Alliance operates a fleet of large capacity hydraulic face shovels and more than 40 X 240 t capacity haul trucks to deliver annual production in excess of 40 Mbcm per annum. The Mt Keith Nickel mine is currently operating at a depth to 300 m below surface with a planned final depth of the order of 500 m. As is the case with any large open pit managing the health of the workforce on continuous shift operations is of critical importance to achieving outstanding safety and production outcomes. Fatigue management at Mt Keith is effectively managed by the personnel operating the mining equipment, with assistance and understanding of the management team and supervisors. The program has been driven through the introduction of Fatigue Champions and a comprehensive management plan that includes education, individual health plans and the use of new technologies. Mt Keith has been instrumental in trialling new technology which assists in monitoring fatigue in operations personnel. Insight into these developments is provided in the context of the overall fatigue management plan. The field trials of the OptAlert(TM) system and how it assists in measuring fatigue is explained. The implications for individual operators and the context for a fleet wide approach to fatigue management is also discussed. Mt Keith has recently completed the second phase of trials with the result that this new and exciting technology is being considered for adoption globally across BHP BillitonÆs open pit mining operations.

Jan 1, 2007

By A Campbell

Open pit blasting at Ernest Henry Mining has the potential to cause damage to nearby underground workings. This paper is a case study of the blast vibration management project that was conducted to ensure open pit blasting did not adversely affect the stability of upper production levels or cause damage to the underground primary fan units. The two upper levels of the underground mine surround the lower portion of the open pit mine. The remaining underground mine workings are directly below the open pit mine. This paper details the process developed to prevent open pit blasting causing excess vibration in the underground mine. Measurement of test blasts combined with historic blast monitoring data was used to determine site specific blast vibration parameters. Threshold vibration levels for blast-induced damage to underground drives and the fan chambers were developed from benchmarking and non-linear numerical modelling. A Monte Carlo simulation model was used to predict vibration levels in critical underground areas. Blasts predicted to exceed maximum vibration levels could then be redesigned to avoid damage.A scale distance law for determining peak particle velocity (PPV) from the distance and charge weight of blasts was developed. Underground observations were used to develop a site-specific relationship between PPV and ground support/rock mass damage. A Monte Carlo superposition prediction model was developed and compared to measured data to refine input parameters. Standards for redesigning open pit blasts in order to reduce blast vibrations whilst minimising impacts on productivity are described. Non-linear numerical modelling was used to establish the dynamic capacity of the fan chambers, and set a PPV of 250 mm/s as a threshold for damage. The numerical model captured the full dynamic behaviour of the fan chambers and installed support, including transient stresses, strains and induced damage, when subjected to a simulated open pit blast.This case study also outlines a procedure for monitoring and predicting blast vibrations at other mine sites where open pit blasting has the potential to impact on a nearby underground mine.

Nov 8, 2011

By B W. Atkinson, J Docherty

An Australian Working Group has been compiling a guide for operators to use in order to improve the efficacy of their routine and non-routine sampling tasks within their coal preparation process. The guide focuses on unit operations within the process, and not conveyor belts or transfer stations that are adequately covered by the existing Standard ISO 13909.Representative sampling of unit operations is generally an after-thought following plant construction, whether that be a result of oversight, or more commonly, capital cost minimisation during initial construction. Minimising capital cost by avoiding adequate sampling systems is generally a poor decision, since the result is a process that cannot be adequately measured, meaning that it cannot be adequately managed and optimised.The use of the term ‘guide’ rather than ‘standard’ is intentional. Practical means of sampling unit operations within existing plants generally relies on a compromise between sample representativity (minimisation of bias) and sampling feasibility. The guide does not endorse poor sampling practice, but instead offers practical guidance to overcome, to the extent reasonably possible, real-life limitations.When it comes to sampling any particular process, it is almost always necessary to make a professional judgement as to whether or not the proposed samples are likely to be sufficiently representative such that the sampling will be worthwhile. Such judgement needs to be exercised by personnel who understand the principles of sampling, as they apply to the stream being sampled. There are many circumstances where available methods for sampling of a particular stream will be meaningless, and in such circumstances analytical data from that sampling will only serve to propagate poor decision-making.This paper outlines the approach for the guide, the areas it covers and the approaches adopted for different types of unit operations and associated equipment configurations.CITATION:Atkinson, B W and Docherty, J, 2017. A practical guide to sampling in coal preparation plants, in Proceedings Eighth World Conference on Sampling and Blending , pp 241–246 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

"Geometallurgy is a discipline that seeks to improve the sustainability of the extraction of metals and minerals by promoting the smarter use of non-renewable resources, better energy efficiency and greater use of renewable energy. To achieve these goals, development of innovative technologies and approaches are being developed along the entire commodity value chain, starting with exploration and extraction and extending to reuse and recycling. This paper discusses the geometallurgy of industrial minerals with special emphasis on kaolin, a versatile industrial mineral applied in ceramics, paper, paint, plastics, rubber, pharmaceuticals, cosmetics, ink, sealants, adhesives, sanitary ware, glass fibre, toothpaste, animal feed etc. Aspects of kaolin extraction in south-west UK are analysed from a geometallurgical perspective. While geometallurgy already features in kaolin extraction, its role can be significantly expanded by combining advanced in-pit characterisation and orebody modelling with integrated planning and control of the refining and calcination process. This paper highlights the importance of innovation in realising the full potential of geometallurgy.CITATION:Glass, H J, 2016. Geometallurgy – Driving Innovation in the Mining Value Chain, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 21–28 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By J H. Zietsman

The transition to more sustainable metal production is receiving much attention at present, and the iron and steel industry is at the centre of the conversation. New, more environmentally friendly production technologies, such as direct reduced iron (DRI) smelting furnaces, need to be developed in a short period of time. This necessitates increased use of computational modelling that incorporates more accurate material descriptions. The combination of large-scale multiphysics models of high-temperature processes with CALPHAD material descriptions leads to infeasible computation times. This can be resolved with the previously reported RapidThermo framework, which has been demonstrated to make equilibrium calculations orders of magnitude faster, within controllable limits of accuracy. In this paper, we explain how further material properties, which are important to modelling hightemperature reactors, can be added to the RapidThermo framework. This can improve the accuracy and usefulness of process and multiphysics models in the development of new technologies, which can significantly accelerate development cycles.

Aug 21, 2024

By P Esteves, J L. Bechir, R Galery, C Senna, V Souto

The current moment experienced by the mineral industry is marked by a series of economic, social and environmental challenges. Among the main challenges, it is important to highlight the decreasing in ore grades with the gradual depletion of the existing deposits, the high volatility in international commodity prices and the operational inefficiencies in the mine, beneficiation, and metallurgical plants. In this context, mining companies are continuously looking for alternatives that minimize production costs and maximize overall production. In addition, recent tragedies involving tailings dam collapses in Brazil, reinforced the need for a more responsible, sustainable, and conscious mining, such as aiming the preservation and rehabilitation of the land environment. In this scenario, the Sensor-Based Sorting (SBS) technology is currently getting more space into the mining market. This separation technology aims the removal of gangue material in coarse particle size fractions, prior to comminution and concentration stages. As a consequence, the technology allows a smaller consumption of energy, water, chemical reagents and other inputs. Moreover, the sensor-based sorting is a dry processing technology and favors the reduction of fine material to be sent to the tailings. The aim of this paper is to provide information regarding the technical and economical evaluation of SBS technology applicability to a zinc silicate mining in Brazil. The project evaluation was performed in two stages: laboratory test work and the execution of a pilot plant. The execution of a pilot plant allowed the technology optimization, quantification of downstream process effects, such as a proper economic evaluation about the technology benefits. Keywords: Sensor-Based Sorting; Particle Sorting; Ore Sorting; Preconcentration; capital expenditure (CAPEX); operating expenditure (OPEX); zinc; comminution; dry processing.

Nov 10, 2020

The sixth international symposium on mining with fill nearly coincides with the 25th anniversary of the Jubilee Symposium on Mine Filling. That symposium, held in August 1973 in Mount Isa, in part to commemorate the 80th anniversary of The Australasian Institute of Mining and Metallurgy, was the first in what has turned out to be a very successful series of symposia. Subsequent symposia were held in Sudbury, Canada (1978), Lulea, Sweden (1983), Montreal, Canada (1989) and Johannesburg, South Africa (1993). The series of symposia has now become an established part of the mining industry calendar, and it will be interesting to see which country is given the honour, and accepts the challenge, to organise the next symposium. When the chairman of the conference organising committee invited (or was it instructed?) me to prepare and deliver one of the keynote addresses, his request was for me to be in parts historical, controversial, predictive and entertaining. The mix was left to me, with one proviso - that an early pioneer of mine filling in Australia be given due recognition. The chairman of the organising committee alone will be able to determine if I fulfilled the last objective. My success, or otherwise, with the other objectives will have to be judged by my fellow delegates. One way of predicting the future, or some small part of it, is to revisit where we have already been with a view to determining the existence of any trends that may impact on the future. An historical review of filling practice and research, with special emphasis on Australian experience in particular and worldwide in general over the previous 25 years, will enable me to address the historical and predictive objectives.

Jan 1, 1998

By J Elder

Magnetic separation equipment has long been used to upgrade and beneficiate a wide variety of minerals and materials. Over the years, significant advances in both wet and dry magnetic separators have improved their operability and separation performances, broadening their use.But no one answer exists to the question: what is the right type of magnetic separator? For many minerals, including ilmenite, both process routes may be viable. There are technical, production, as well as economic reasons for choosing wet versus dry. However, recent developments illustrate that a new generation of wet magnetic separators is approaching performance once seen only in dry magnetic separation. With quality and production performance becoming similar, the choice between wet and dry magnetic separation is not as cut and dry as it once was.

Oct 5, 2011

By Glasson K. R

The history of Ore Reserve classification and reporting in Australia is largely a history of the Australian mining industry itself. In the late 1800s, when the industry was dominated by small scale, high grade underground mines, Reserves (if estimated) were based on hand sampling and geological inference, and reporting of Reserves was either non-existent or of extremely variable quality. By the mid-20th century, the industry was dominated by large underground base metal and gold mines. Reserve estimation was coming under the control of skilled geologists and mining engineers, however Reserve classification and reporting standards continued to vary in type and quality from mine to mine. Today, large scale, low grade mining operations predominate, and Reserve estimates are generally based on extensive drilling results processed (with geological control) by computer. Through the efforts of a Joint Committee established by The Australasian Institute of Mining and Metallurgy and Australian Mining Industry Council, Reserve and Resource classification and public reporting has been standardised and controlled by adoption of the ""Australasian Code for the Reporting of Identified Mineral Resources and Ore Reserves"" released in 1989. The Code, which will continue to be modified and improved by the Joint Committee, has also been used as a basis for guides to reporting in other countries, and there is now some hope that this difficult and vexing topic may finally become subject to international standards and controls.

Jan 1, 1992

The words ""Uncertainty"" and ""Risk"" pervade every discussion about mining exploration and investment. Perhaps these terms are subjectively understood by industry professionals, but objective portrayal of these concepts outside the industry is a woefully undeveloped science. This paper addresses current industry understanding and practice regarding quantitative risk assessment techniques, and provides examples of the application of three of these techniques. Probabilistic techniques for financial risk assessment are valuable adjuncts to conventional financial analysis, and address a range of issues not assessable by any other means. The value of whole-of-project probabilistic risk assessment is currently debatable for decision-making purposes, but is seen as important as a mechanism to focus attention to the critical issues that ultimately impact on project success. The dissection of project capital into risk and non-risk components provides valuable insights into risk characteristics not readily quantifiable in any other way. This technique also provides a framework for more objective ""what if?"" scenario evaluation and for the capital structure of resource projects. Finally, mechanisms for the valuation of undeveloped reserves are examined, and guidelines suggested. The importance of reliability in production cost estimates is highlighted and the impact of early development on reserve valuations is discussed. The importance of economics throughout all stages of the evaluation process is fundamental.

Jan 1, 1994

By M P. Murphy, C M. D Barton

When developing a new underground mine, the geological interpretation that guides the mineral resource is crucial to the preparation of a reliable ore reserve. In preparing a robust geological model to underpin a resource estimate, practitioners must weigh the comparative risk of accepting a relatively wide-spaced drill hole pattern, versus a more close-spaced pattern that ensures a high local geological confidence for mine planning but may have an exponentially increased time and monetary cost. This paper details the authors’ investigations into the geological uncertainty of IGO’s Odysseus Deposit, which is approximately 645 km north-east of Perth, Western Australia. At Odysseus, the komatiitic nickel sulfide mineralisation is irregularly cross-cut by nickel-barren pegmatites that have intruded and offset its thick ultramafic orebodies. These pegmatites generate significant uncertainty in the precision of Odysseus’ resource volume and tonnage estimates, as well as the subsequent quantification of pegmatite mining dilution in its ore reserve. To quantify the geological uncertainty in the pegmatite interpretations, IGO’s mineral resource practitioners prepared several geological risk studies over the Odysseus North lode, which is the lode most affected by the pegmatites. These studies included categorical conditional simulation of the pegmatites, preparing implicit geological models with alternative algorithms, trialling a machine learning application to prepare a maximum likelihood geological model, and finally assessing the early results of the pre-production close-spaced drilling to these different models. To assess the precision of the different single-outcome models, the authors’ compared the estimated pegmatite content of each model to the range of possibilities modelled by categorical conditional simulation within the planned stopes at Odysseus North. An estimation confidence score for each modelling method was then prepared for each alternative single-outcome modelling method. From these studies IGO concluded that a close-spaced drill pattern is essential at Odysseus, supporting the view of the Competent Person in 2017 who proposed a 25 m drill spacing in areas affected by pegmatite which had been partially classified as Inferred.

May 24, 2023

During operations, mining and metallurgical processes may generate effluents such as tailings water, acid mine drainage (AMD) and seepage and process acid streams. Depending on the type of ore and the metallurgical process, these effluents may contain one or more toxic compounds (eg acidity or alkalinity, cyanide, ammonia and/or nitrate, heavy metals, total suspended solids (TSS), sulfate) in elevated concentrations requiring treatment before their discharge to the environment or recycle/reuse in the process. Natural oxidation of sulfide minerals present in mining wastes (eg tailings and waste rock) at mining sites may generate AMD, which is characterised as a low pH, high acidity effluent containing heavy metals and sulfate. If generation of AMD cannot be controlled and/or prevented, AMD needs to be collected and treated for neutralisation of acidity and reduction of metals and TSS to meet regulated water quality standards. It is important to note that some of these compounds may persist in run-off from mine sites, even after the mine and processing facilities are decommissioned. Treatment of mining and metallurgical process effluents can be accomplished by means of various physical, chemical and/or biological methods. The mode of process application may vary from the use of either specifically designed, controlled and automated facilities or passive systems. Lime neutralisation and precipitation is the most common method used in the mining industry to treat AMD. To reduce the problems associated with disposal and long-term storage of the resulting sludge, the use of a high-density sludge process (HDS) has become a preferred option. The use of other chemical reagents, waste or by-products from other industries, and biological sulfate reduction methods can also be considered as viable options for site-specific situations. Recently, several passive treatment systems have been designed and successfully operated, even in the cold North American climate. This paper will discuss available options and provide insights for selecting a suitable method for a given situation using case studies from projects conducted by Golder Associates around the world over the last decade.

Jan 1, 2006

Rope guides, consisting of ropes spanning between anchor points at the top and bottom of shafts, have frequently been considered as a viable alternative to fixed guides, comprising buntons and guides. However, their design has generally been based on empirically derived rules, arising from European hoisting practice of 50 to 100 years ago. This paper describes a recent technology development project aimed at defining and quantifying the important forces acting on rope guided conveyances, calculating the resulting displacement of the conveyances and assessing whether the displacements are acceptable or not. The paper describes the derivation of aerodynamic force coefficients based on CFD analyses and other significant forces acting on the conveyance and rope system. The conveyance displacements may be calculated using computer simulation of the mechanical system, or approximately using simplified equations given in the paper. Measurements taken to confirm the suitability of the proposed formulation are described. The combination of displacements and assessment of the rope guide system design are proposed, based on the ratio of design clearances and the predicted displacements.

Jan 1, 2005

By M A. Noppé

"Investors and other stakeholders assessing the risk, opportunity and relative value associated with a resource project need to appreciate the project in its correct context. Errors, omissions, biased reporting or conflicting information in project reporting may lead to a misinterpretation of technical and financial results, resulting in biased estimates or assumptions on project value.This paper provides a simple ‘Resource Project Framework’ for presenting a project’s status that may be readily benchmarked against other similar projects and to illustrate the stages required to advance the project outcomes to higher levels of certainty. The framework draws on definitions and guidelines readily available in various resource industry reporting codes and public company reporting requirements.The framework assesses three key areas for placing a resource project in its correct relative context, namely:the project development stagethe confidence in the Exploration Results, Mineral Resources and/or Ore Reservesthe level of accuracy, precision and confidence in the technical and economic studies supporting the reported results or options for the project.The application of the Resource Project Framework is illustrated using two project examples, one from publicly reported company project releases and the other for two development projects.CITATION:Noppé, M A, 2016. A framework for presenting and benchmarking resource projects, in Proceedings Project Evaluation 2016, pp 260–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By C Slaughter, J C. Tien

Commonly held ideas about effective training have long emphasised the importance of realism. Realistic training builds better experience among the trainees and a better perspective on the training material, making training more effective. While great strides have been made in this realm for mine safety and mine rescue training there are still areas that can be improved. One possible area is the expanded use of a mine fire simulation program where the migration of gases and smoke can be realistically displayed in an emergency, and outcomes varied as different conditions are being simulated. The use of mine fire simulation software potentially allows for the creation of more realistic scenarios in that smoke advance rates can be measured and recreated in evacuation scenarios, or that gas readings in mine rescue training can be dynamically and realistically changed to show the effect that time has on the fire scenario.CITATION:Slaughter, C and Tien, J C, 2015. The potential use of mine fire simulation software as an enhancement for mine safety and mine rescue training, in Proceedings The Australian Mine Ventilation Conference, pp 285–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D J. A Van Zyl, J C. Cunning

Technological advances associated with the expanded application of paste technology in underground mine backfilling are now stimulating an interest in the disposal of process tailings as paste in the surface environment. Concurrent with the development of alternative surface tailings disposal practices is the requirement to fully understand the consolidation behaviour of tailings in paste form, and to relate this understanding to the significant body of data and operating experience from decades of study of the performance of hydraulically placed tailings. One effective method for demonstrating the benefits derived from handling and placement of tailings as paste is to review tailings slurry consolidation theory from the perspective of the changes which take place in the material as it makes its transition from a loose slurry to a dense, stable deposit resulting from managed thin-layer deposition. For a typical process tailings, an example is provided which illustrates the effect which mechanical dewatering has in accelerating the consolidation process and thereby providing a range of benefits from the perspective of surface disposal. Increased rates of filling (rise), expanded use of upstream embankment construction methods and elimination of impounded surface solutions are some quantifiable benefits which can be assembled on a site-specific basis to allow for valid comparisons with more traditional approaches to tailings disposal.

Jan 1, 1998

By M Hourn, G Anderson, V Lawson, P Voigt, D Mallah

As mine head grades decline and orebodies become more complex, traditional mineral processing techniques and flow sheets to achieve saleable concentrate become more difficult to design and construct. Mines with lower quality concentrates or concentrates with penalty elements are particularly under threat. The economics of such operations are far more susceptible to metal price fluctuations, concentrate treatment terms and the availability of other, cleaner concentrates. Additional value may be realised for these orebodies through improved recovery by producing a low grade middling concentrate for further processing, in conjunction with a saleable concentrate.The most economic effective way to reduce impurity levels is to do so as early as possible in the mining value chain. Technologies such as fine grinding and fine particle flotation are well established as effective methods for impurity rejection in mineral processing. What is often overlooked is how a hydrometallurgical process could also be integrated in the overall flow sheet to achieve higher overall recovery at the mill. In the base metals environment, this is probably because hydrometallurgical processes are associated with production of metal, or require the use of expensive and toxic precipitating agents once the minerals of interest are in solution. These processes can be very expensive, particularly with rising power costs and poor economies of scale in capital costs associated with low production rates from middling streams. Glencore Technology (GT) has recent experience in the treatment of middling and low grade concentrate streams and also tailings streams to complement a concentrator flow sheet in a refractory gold and base metals setting. The value proposition is the isolation of a low grade middling concentrate from the primary circuit or the tailings stream for upgrading to an intermediate product with an equal or higher grade than the primary concentrate to allow blending for sale. This allows the plant to operate on a more favourable part of the grade-recovery curve while avoiding the expense of metal production. For existing operations this is particularly attractive since it can be added to the flow sheet with no process interruptions. Two case studies are examined showing flow sheets and costings to arrive at the value proposition of the GT low grade treatment flow sheet.CITATION:Voigt, P, Hourn, M, Lawson, V, Anderson, G and Mallah, D, 2017. Economic recovery and upgrade of metals from middling and tailing streams, in Proceedings MetPlant 2017, pp 289–297 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017