Search Documents

By E. Swartzman

"DURING 1951, experimental cleaning studies on both fines and larger sizes of certain Canadian coals were conducted on a relatively large scale in two pilot plants in the United States, large enough to be considered as small commercial units, and in one commercial plant in Canada.One of the pilot plants was a wet washer of a type which apparently has never been .used in Canada, nor has any Canadian coal been tested in it before. In the other pilot plant and in the commercial plant, dry cleaning equipment was used. The commercial plant is the first of its kind to be employed in Canada, and this type is used only to a limited extent in the United States.Fine-Coal Cleaning ExperimentsTest PlantsHydrotator and Hydrotator-Classifier combination pilot-plant with a capacity of about twenty tons per hour. This is a classifier type washer adapted for cleaning fine coal as well as certain intermediate sizes. The Hydrotator deals with that portion of a coal retained on approximately a 24-mesh Tyler sieve, whereas the Hydrotator-Classifier deals with the minus 24-mesh fines."

Jan 1, 1952

By Y. A. Topkaya

In this research work, a process was described for the recovery of copper and zinc in copper converter flue dust from the Black Sea Copper Works' Samsun Smelter Plant. After characterization of a representative flue dust sample, the process included roasting of the flue dust and then leaching in dilute sulfuric acid solution. Roasting time and temperature were studied to determine the optimum roasting conditions. Sulphuric acid concentration, duration, temperature of leaching and solid to liquid ratio were the parameters studied in the bench scale laboratory leaching experiments.

Jan 1, 2007

By K. Barbetti

"The carbon-in-pulp (CIP) process has been the dominant gold recovery process since the early 1980s. CIP has proven to be very adaptable for a wide range of ores and circuit configurations. The key performance indicator for CIP circuits is the minimisation of soluble gold losses to tailings, however, it is also important to operate the circuit efficiently (maximising gold loadings on carbon and minimising carbon inventory). Over the last 30 years the Curtin Gold Technology Group has studied CIP circuits as part of an on-going collaborative industry funded project (the AMIRA Gold Processing Technology Project). In the early years the project undertook basic research into understanding activated carbon, and its management in the circuit. More recently the development of process models and instrumentation has provided additional tools to assist operators. The results show that while most CIP circuits operate well, there are still significant opportunities for further cost savings, or additional revenue. This paper reviews the observations arising from this work, including key requirements for good carbon management, the results of benchmarking and industry surveys of carbon circuit over 20 years, the value of process modelling of CIP circuits to establish operating parameters, and the use of automated instrumentation to better optimise carbon control in the circuit.INTRODUCTION The introduction of activated carbon to recover gold from cyanide leach solutions in the last quarter of the 20th century was the most significant development in gold ore processing since the advent of cyanidation seventy years before. Replacing the Merrill–Crowe zinc cementation step with carbon-in-pulp (CIP) or carbon-in-leach (CIL) circuits provided a process that allowed the treatment of lower grade and problematic ores (e.g. high-clay ores), at lower capital and operating costs, and higher metal recoveries. The CIP circuit was first developed in the 1950s at the Carlton Mill, Cripple Creek, Colorado. All the components of the modern CIP process came to fruition at the Homestake Mine in South Dakota in 1973 (Fast, 1988). From the late 1970s onward a variation of CIP, carbon-in-leach (CIL) which combined the leach and adsorption stages, became the preferred circuit design in most parts of the word."

Jan 1, 2017

By M. Meratian

The in-situ methods have been developed in production of aluminum matrix composites. A commonly adopted in-situ method involves reaction between a metal oxide and aluminum to produce alumina particles or whisker reinforcements. Aluminum-alumina particle composite was fabricated by in-situ method where alumina particles were produced from reduction of copper and silicon oxides by melting and casting aluminum. Aluminum matrix composites reinforced by Copper and Silicon alloying elements and alumina particles have been obtained. The size and shape of alumina particles were studied by scanning electron microscopy (SEM). The size of alumina obtained from mixture of SiO2 and CuO was bigger than the alumina particles obtained from CuO.

Jan 1, 2007

By Bruno Lafrance

Abstract - Quartz veins at the Mufferaw gold prospect and Komis gold deposit, northern Saskatchewan, are examples of oblique-extension veins that crystallized in shear and tensile fractures, which propagated and then opened oblique to their walls during a single continuous deformation event. The Mufferaw gold prospect consists of an interlinked mesh of conjugate shear fractures, tensile fractures, and veins. Oblique-extension veins crystallized in conjugate shear fractures, which opened during dilation of intersecting tensile fractures under the same far-field stress system. At the Komis gold mine, tensile and dextral shear fractures cut across granodiorite dikes. The tensile fractures formed perpendicular to the dike margins during stress transfer from the less-competent country rocks to the more-competent dikes. During extension of the dikes oblique to the bulk extension direction in the country rocks, the tensile fractures were reactivated as sinistral shear fractures. The reactivated tensile fractures and dextral shear fractures opened oblique to their walls, parallel to the bulk extension direction, and were sealed by the deposition of oblique-extension veins during the same deformation event.

Jan 1, 2004

By Belinda Campbell

Tools for Consistency 1. GIS Web Site 2. National Project Management System 3. Site Grouping Approach (721 PIDs) 4. Mine Reclamation Standing Offer Agreements ?Contracting tool 5. Remedial Objectives Guidance Document Background ?CBDC (now ECBC) is a Federal Crown Corporation and falls under federal jurisdiction. ?When it stopped mining coal, CBDC turned its attention to cleaning up and closing out its industrial sites. ?Public Works and Government Services Canada is common service provider to the GoC. ?Expertise in environmental, engineering, IT, project management, communications, GIS, real property management.

May 1, 2011

By Mayumi Ito

Mineral processing of rare-earth ore from the Dong Pao deposit, Vietnam, was investigated. The ore contained bastnaesite, (REE (rare earth element)) CO3F, as the valuable mineral and barite, quartz, and fluorite as gangue. To establish a mineral processing flowchart, selective comminution, size classification, and magnetic separation were tested. Bastnaesite shows brittle properties and selective comminution was applied to improve the purity of products. The crushed products were classified by decantation, and the overflow product showed high purity of bastnaesite indicating that bastnaesite becomes fines by crushing and that selective crushing can be used to concentrate the bastnaesite. Magnetic separation for the sink product was carried out and the mag-product showed high recovery rates of bastnaesite, indicating that the combination of size classification and magnetic separation is effective.

Aug 1, 2013

By N. R. Andrade-Gonzalez

The present work was performed on four alloys containing Al-6 2 wt pct Si-3 5 wt pet Cu, with magnesium in the range of 0.02-0 40 wt pct, and strontium in the range of 0-165 p p m Tensile bars were cast in a permanent mold (ASTM B108-160) and heat treated at 495°C for 4 hours, followed by quenching in hot water. Two different artificial aging temperatures were applied at 180 °C and 220 °C for times from 0 5 h up to 8 h Tests were conducted with the intent of determining how the mechanical properties of an aluminum-based 319 alloy are affected when aging time and temperatures are varied In general, it is seen that the alloy does not exhibit the common peak-overaged aging condition due to the presence of several coexisting phases, indicating that they form through complex eutectic reactions late in solidification.

Jan 1, 2004

By Chris M. Healey

"The Jasper Gold mine in northern Saskatchewan produced a total mill feed of 140 127 tonnes at an average grade of 19.0 g/t Au. Both diamond drilling and chip samples from underground workings returned extremely high values, up to 12851 g/t (375 oz/T) Au over 0.10 meter from a chip sample. In the presence of such extremely high grades, the accurate estimation of reserves is a major problem.In the first part of this study, production data from the mine were used to evaluate the results of a variety of reserve estimation techniques in this environment. In two out of three cases studied, indicator kriging with assays cut to 342.9 g/t (10 oz/T) gave extremely good results. In the third case, however, indicator kriging gave unacceptable results. Instead, lognormal kriging of uncut data gave the best results.Secondly, from the same database, a number of drill-hole spacings were simulated, and reserves estimated from the simulations. As may be expected, the results of this analysis show increasingly better results with tighter drill-hole spacing. However, even with a 5 m by 5 m spacing the variation from actual grade was quite large. This is not a systematic under- or over-estimation of grade, rather a random scatter of results.The results of this study show very clearly the problems of deriving good estimates of reserves when extremely high-grade samples are encountered. There is a high degree of randomness to this data base, so reserve estimation in this situation will remain a high-risk operation."

Jan 1, 1993

By B. Galy, L. Giraud

"This paper compares Canadian provincial mining safety regulations regarding the use and testing of cage safety catches, including a brief history and evolution. Regulations are similar across provinces, with only slight variations. Currently, the “Ontario-type” safety dog is the most commonly used safety catch in Canada. Performance estimation of the compensation mechanism for different safety-dog shapes and tooth angles show this shape works well and has consistent braking results, but the best efficiency is obtained for initial tooth angles greater than 10°. Miner safety is questionable for lightly loaded cages, an issue that should be addressed technically and legislatively.RÉSUMÉ Le présent article compare les diverses réglementations de sécurité minière concernant les parachutes des cages dans les provinces canadiennes ainsi que les essais qu’ils doivent subir. Il semble que les réglementations soient semblables à travers les provinces avec quelques légères différences ou divergences. Un bref historique des parachutes et de leur évolution est présenté. De nos jours, le parachute de « type Ontario » est le plus fréquemment employé à travers le Canada et il présente des résultats de freinage uniformes. Une estimation de la performance du mécanisme de compensation pour les diverses formes de taquets de sécurité et les divers angles des dents montre que cette géométrie fonctionne bien; cependant, la meilleure efficacité est obtenue pour des angles de dents supérieurs à 10°. La sécurité des mineurs est mise en jeu pour des cages faiblement chargées et ce point devrait être traité du point de vue technique et du point de vue législatif."

Jan 1, 2016

By M. I. Abbas, M. A. Shahin, M. S. Ahmed

"The influence of annealing of galvanized steel (galvannealing) on its corrosion kinetics in a saturated solution of Ca (OH)2 has been studied by means of the polarization resistance method.Galvannealing heat treatment was carried out at 450°C and 550°C for varying times. Annealing at 450°C for 24 hr or at 550°C for 5 hr showed the highest corrosion potential (Ecorr) ~= - 400 m V/ SCE as well as, the lowest corrosion current density (icorr ~= 3 mA.cm-2, while Ecorr and icorr of the unheated specimens were ~= - 1400m V/SCE and == 20 mA.cm-2, respectively.Polarization curves were also obtained for the as-received galvanized specimens together with the galvannealed ones.INTRODUCTIONHeat treatment of galvanized steel (i.e . galvannealing) is carried out at a temperature range of 450°C to 550°C for a time sufficient to convert the free zinc coating to an alloyed one consisting of layers of iron-zinc intermetallic compounds. Table I is a review of the properties of the Fe-Zn intermetallicphases while Figure I is a reproduction - of the Fe-Zn equilibrium phase diagram taken from Hansen.Several authors have studied the formation of intermetallic phases through the interdiffusion of Zn/Fe couples. Their results confirmed the stability of intermetallic phases that could be shown up on the outer surface as a result of galvannealing of galvanized steel.Bernick and Sievertv"" investigated the processing of galvan nealed steel. They found that the galvannealed coating with the best forming qualities consisted of a mixture of Zeta phase and Eta phase."

Jan 1, 1989

By C. D. M. Chisholm

IN discussing stope filling, or backfilling, at the Sullivan mine, at Kimberley, B.C., a brief description of the problem will first be presented. The Sullivan orebody is a replacement in quartzite, with the ore con-forming, for the most part, with the bedding. The dip of the vein, apart from local irregularities, averages about 15 degrees near the outcrop in the southwest section of the mine, and steepens to almost 40 degrees at the northeast end of the mine. The thickness varies from a few feet to over 200 feet at the widest sections. The mineable length along the strike has averaged about 4,000 feet between the 4,600 and 3,900 levels-the section under discussion in this paper. To date, 28,000,000 tons of ore have been mined by the room-and-pillar method. Prior to 1930, all ground opened up had been supported by ore pillars, left during mining operations. From that time, the recovery of the ore from these pillars has been given serious consideration. Backfilling, as being carried on today, is the result of this study and is being done for two reasons: (1) to allow extraction of the ore pillars, and (2) to minimize subsidence of the hanging-wall rock, except where forced caving is found desirable. PRELIMINARY DEVELOPMENTS LEADING TO BACKFILLING When the Sullivan orebody was first opened up, early in the century, there appeared to be low-grade sections of the vein sufficient in extent to serve as permanent support for the roof. However, as mining extended into sections of the vein that showed continuous ore over greater areas, wooden cribs, filled with waste and low-grade ore, were erected. In some stopes, these cribs were as large as 40 ft. by 100 ft. in plan and from 50 ft. to 60 ft. in height, but it was soon realized that this method of support was inadequate. As mining progressed, it was found necessary to leave ore pillars, which eventually became the sole system of support. At first, these pillars were left at irregular intervals, but later they were laid out at definite locations on the mine plans, and these locations were adhered to as closely as mining would permit.

Jan 1, 1941

By R. A. Lunceford, K. C. Shaver

Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km Acquired by Teck Corporation in 1990, the White Earth project, located in southwestern Colorado is the largest titanium resource in the U.S. Teck Corporation has conducted geologic, reserve, mineral processing, pre-marketing, and environmental baseline studies directed toward the economic feasibility of producing titanium pigment. The White Earth project is situated in a 31 km2 alkalic-carbonatite complex intruded into Precambrian granite and metamorphic rocks about 570 million years ago. Perovskite occurs in a 8 km by 1.2 km

Jan 1, 1998

By P. Fleming, W. Pascheto

"Rod mills processing nickel and copper ore experienced recurring failures of liner bolts. In some cases failures became very frequent, requiring constant mill intervention and consequently impacting process stability and operating costs. Investigation related to the causes of bolt failures involved a multidisciplinary approach with the participation of engineering, maintenance and operation. It included the determination of bolt failure mechanisms as well as the assessment of mechanical properties, fabrication quality and handling and installation procedures. In addition, other parameters affecting bolt performance such as mill and liner design, operating parameters and maintenance practices were studied. This paper reports the failure investigation results and proposed solutions for failure prevention. INTRODUCTIONOccasional liner bolt failures are common in rod mills. However, chronic bolt failures developed in rod mills processing nickel and copper ore caused frequent shutdowns for bolt replacement to an extent that affected process stability. At first, it was thought that the cause of recurring failures was related to bolt quality. The operation then submitted several failed bolts to failure analysis. However, it became apparent that bolt quality was unlikely to be the main cause of failures. The determination of root cause (s) then became more complex, requiring a multi-disciplinary approach to failure investigation, requiring the assessment of bolt installation methods, mill design, operating conditions and maintenance practices. The results of the metallurgical failure analysis and investigation of other possible causes of failures are reported here."

Jan 1, 2016

By A. Yousefpour, M. Hojjati, G. Chouinard

In recent years, high performance thermoplastic composites such as PEEK and PEKK have been developed for aerospace applications. These materials offer, among the other properties, high toughness and damage tolerances. These are semi-crystalline materials and their processing can lead to different crystallinity that in turn have some impact on the final properties. The effect of cooling rate on degree of crystallinity of PEEK is studied to identify the processing window for manufacturing. Samples were heated at the constant heating rate of 20°C/min up to 375°C (above melting point) and held for 10 minute. The enthalpy of the crystallization was measured at different constant cooling rates of 0.5, 1, 2, 5, 10, 20, 30, and 40°C/min. After cooling, the samples were heated at constant heating rate of 2°C/min using modulated DSC. At temperature between 90°C to 375°C, two endotherm peaks were observed. Results suggest that endotherm peaks are related to a melting and recrystallization phenomenon of one crystal morphology. However, the second endotherm peak could be associated with another crystal structure or morphology.

Jan 1, 2006

By D. Lascelles, J. A. Finch, E. El-Ammouri

Flotation separation is expected to be related to the degree of dispersion of the pulp. For instance, highly aggregated systems may show reduced selectivity, reduced entrainment and increased flotation rate. In an attempt to test the impact of aggregation on flotation, we have taken advantage of the effect of Mg ions. Using combinations of Mg2+ and pH gave a wide variation in aggregation of several Cu-Zn ores (measured by settling rate) and corresponding flotation response was determined by batch tests. The trials were conducted on-site at Louvicourt and Agnico-Eagle. In a majority of cases a similar trend in aggregation and flotation selectivity (grade at given recovery) was observed. At Louvicourt, improved selectivity with increasing aggregation at pH 10.5 was found. At Agnico-Eagle, an analogous association between aggregation and selectivity was observed at pH 11.5. It is suggested that aggregation influences particle entrainment, the increased effective particle size reducing gangue recovery and hence improving selectivity.

Jan 1, 2004

By Chia-Chi Chiu, Meng-Chia Weng, Tsan-Hwei Huang

"This paper proposes a biconcave shape bond model for the distinct element method (DEM) to simulate cementation between two circular particles in geomaterials. Rather than an original parallel bond model between particles, the proposed model adopts the more realistic shape of cementation and considers the elastic response of cementation under external loading. The stress field and force-displacement relationship of the biconcave shape bond is based on Dvorkin’s theory, and three modifications are adopted: (1) A superposition method is applied to improve the correctness and symmetry of the stress field, and it also provides a method of addressing the status when both connected particles rotate; (2) To simplify the input parameters, the tangential movement is replaced by the normal deformation and rotation between particles; (3) To accelerate the calculations, variables are extracted in analytical procedures, which provide an efficient method for applying the bond model with only one matrix inversion. With these three modifications, the new biconcave shape bond model is created.To assess the validity of the proposed model, this study compared the elastic deformation in a single bond with an elastic analysis performed using the finite element method (FEM). After verification of the proposed model, a series of sensitivity analyses was performed to explore the effect of bond shape and the differences from the parallel bond model. For a single bond, the results showed that a biconcave model can represent the mechanical behavior of a biconcave shape bond and is effective with different bond shapes. The stress fields calculated by the biconcave model were more similar to the FEM results than those obtained using Dvorkin’s theory. The width and thickness of a bond have a considerable effect on its stiffness, and the variation of thickness decreases with the width of the bond. In addition, the required parameters can be acquired directly from real bond material rather than using the back analysis procedure for parameters.The biconcave model was further implemented in DEM software Particle Flow Code 2 Dimension to certify its applicability in geotechnical engineering. Using this model, a series of uniaxial compression test simulations was performed to analyze the macroelastic responses of specimens. The results showed that the macrotangential elastic modulus and Poisson’s ratio had a regular tendency, and they agreed with the stiffness variation in a microbond. This finding can assist in determining correlations between microand macroproperties and provides an innovative method for simulating the behavior of cemented granular material."

Jan 1, 2015

By Harry J. Cain

Introduction The property of Pioneer Gold Mines of B. C., Limited, is located in the Lillooet mining district of British Columbia, on Cadwallader creek, 54 miles distant by motor road from Shalalth, a station on the Pacific Great Eastern railway. Milling by the present Company was commenced in 1924, a small amalgamation plant, consisting of a crusher, Bryan mill, and plates being operated until 1928. Tailing from this plant was impounded and later treated in the 100-ton continuous counter-current decantation cyanide plant which was erected during 1927-28 and placed in operation during May of 1928. A second cyanide plant, employing continuous counter-current decantation, having a nominal capacity of 200 tons, has been erected during the past few months and was put into operation during September of the present year. The ultimate capacity of the combined units of the present mill has not been determined, but it is expected to be much in excess of the rated capacity. The Ore The ore, as received at the mill, consists chiefly of quartz carrying free gold, with small amounts of pyrite, arsenopyrite, and pyrrhotite in evidence, though probably amounting to less than one per cent of the total. Some gold is very closely associated with the sulphides. The country rock is a basic igneous rock, probably an augite diorite. Near the vein it is highly altered to sericite, which slimes readily on grinding, and does not settle very well. The quartz is of two types, clear and ribbon. In the latter, the ribbons, which are not much thicker than paper, consist of shattered sulphides. In crushing this ribbon quartz, breakage is often along the streaks, exposing these shattered faces to advantage in subsequent treatment. While gold is the metal for which the ore is mined, some silver is also present and is paid for by the mint. It is, however, unimportant from a commercial viewpoint. From the standpoint of crushing and grinding, the ore might be termed 'medium 'hard'.

Jan 1, 1932

By M. E. Austin

Many numerical models for the tubular solid oxide fuel cell (SOFC) exist, with various degrees of sophistication. However, the question of what physics must be modelled, and what can be neglected has not been resolved. A parametric model is proposed and analyzed to quantify the influence of thermal phenomena such as reaction heat generation, cathode channel convective cooling, and thermal radiation with participating media. Currently, a three-dimensional model is used to simulate the conditions of an anode supported cell in the centre of a tube bundle. The interconnect and nickel foam spacers that bridge adjacent cells in series and parallel, respectively, are neglected thus enabling a domain consisting of a 45o azimuthal section of the tube. The conservation equations for mass, energy, and species transport are solved using commercial computational fluid dynamics software, and radiation heat transfer is also modelled using a Discrete Ordinates method. Finally, temperature-dependent material properties and reaction rates are used. The model predicts lower overall temperatures than models that do not include radiative heat exchange and more moderate temperature gradients than those that ignore participating media radiation. Further, different regimes are identified, from convection dominated heat transfer to radiation dominated heat transfer. The results can be used to aid in the selection of appropriate models for a given fuel cell operating regime.

Jan 1, 2005

By R. M. Oliver

THE Falconbridge property is almost completely covered with over-burden to a depth varying from 60 to over 200 feet. This overburden consists of grave], sand, and boulder, with bands of very fine silt, and there is usually a layer of water-bearing quicksand adjoining the r:ock surface. In previous shafts sunk at Falconbridge, this water-bearing quicksand had given considerable trouble, and further difficulties were expected in sinking No. 5 shaft, due to its greater size. The method described in this paper is the one adopted in sinking this shaft, after the matter had been carefully considered. No. 5 shaft is located 2,400 feet east of the old main No. l shaft, and is sunk in norite in the hanging-wall of the ore-body, which is, however, ? practically vertical to the deepest known intersection. The greatest depths of overburden prevail on the south side, or footwall, of the ore-body, and this, together.. with the fact that the footwall is wet and more badly fractured, swayed the final decision to sink in the hanging-wall. After the shaft site had been chosen and cleared, a diamond drill was set up a few feet away and a hole bored to a depth of 405 feet to test the over-burden and character of the norite bedrock. The depth of overbudren indicated by the hole was Ill feet, with the last 10 feet water-bearing. The norite was rusted and broken up for only a few feet below bedrock. A steel sinking shield (Figure l) was assembled at the shaft location, and consisted of 5/8-inch plate, 5 feet deep, built around a frame of 6 inch by 6 inch angle-iron, and braced at the corners with the same material. Twelve-inch I-beams held the shield as rigid as possible. In order to reduce binding against pebbles to a minimum, the shield was constructed with a 1-inch batter on all sides.

Jan 1, 1938