Search Documents

By A. Rahmati

Geological and geo-statistical modeling of the ore deposits play a prominent role in resource and reserve estimation for geo-statistical evaluations. Sheytoor iron deposit is located in the Bafq iron ore district (Central Iran) and in the south-east of the Esfordi 1:100000 sheet. According to the geological data, limestones and dolomitic limestones are situated in the north and central parts of the area, on the other hand, iron ore outcrops are observable in the center, south-west and south-east of the studied area. Meanwhile this ore deposit represents a sulfide one. Based on the boreholes data, geological and geostatistical models of the high and low grade iron mineralization zones were generated by Rockworks v.15 software. The IDW method was selected and employed for processing the collected data and a good adaptation between the results was revealed. The distribution model of Fe concentration displayed a relatively high grade Fe in the center, south and south-east parts of the area. Furthermore, this model illustrated a relatively high grade S and P in some parts of the center, north and south-east of the area. The Fe concentration, in the high grade mineralization zone, was between 45 and 61.5%. In addition, in the low grade mineralization zone, it was between 3.64 and 57.64%. Moreover, in the intrusive granites, the Fe concentration was between 30 and 48.73%. Due to the significant amount of the sulfur in the deposit model, most of Fe-bearing minerals are pyrite, so it is recommended an evaluation on Cu-bearing minerals and their related elements in the area to get done. Additionally, there are too much Fe values in granitic zones which could be caused by possible measurement errors and the geological classification of the area. Therefore, it should be done more carefully.

Aug 1, 2013

By A. G. Darnley

"IntroductionTHE PURPOSE of this paper is twofold. Firstly, to drawn attention to recommendations which have been accepted by the International Atomic Energy Agency concerning radiometric reporting methods and calibration in uranium exploration, and secondly to emphasize the benefits that- will stem from adopting them. These recommendations are contained in an IAEA Technical Report, No. 174, which has been prepared with the intention of serving as a general guide to the subject. The existence of this specialized report is likely to be unknown to most of those who can benefit unless it is given some publicity by an organization such as the CIM. The recommendations were prepared by a small international committee consisting of Dr, P. H. Dodd , U.S .A. , Dr. R. L. Grasty. Canada, Dr. L. Levborg, Denmark, Dr. M. Matolin, Czechoslovakia , Dr. S. D. Simov, Bulgaria, and the writer.The fact that there are standard scientific units of mass, distance and time is taken for granted, It is also accepted that the type of instrumentation used to measure one of these parameters is irrelevant to the way the measurement is reported. Geophysical parameters such as magnetic field strength and gravity have generally accepted units, the gamma and milligal, which are defined in SI terms. These units are employed irrespective of the operating principle, or manufacturer or organization involved in the measurement."

Jan 1, 1977

By B. Erdem, N. Çelebi

An important problem associated with tandem dragline systems is that of matching the productive capability of individual draglines in the combination. In this paper, a dependence mechanism among draglines in a tandem system is described, and possible consequential problems in a poorly-matched system are defined. The rate of linear advance and the cost of stripping are determined as two major indications for an efficient operation. The proposed decision criteria and the underlying mechanism to select a synchronous couple are introduced and used in simulating tandem dragline systems. The developed model is tested on a hypothetical strip mine where pullback stripping is applied with a tandem dragline system.

Jan 1, 1999

By T. Banerjee, R. deS. Almeida, D. Gudgeon, F. C. F. Batista, L. deÁ. Silva

"Yamana Chapada’s mine is one of the larger copper-gold mines in Brazil. The mine is located in Goiás state, in the central part of Brazil. The mine has estimated Mineral Reserves of 4.1 million ounces of gold and 3.2 billion pounds of copper as of December 31, 2016. While gold and silver are significant, Chapada’s process flowsheet is configured closer to that of copper facilities. This includes a SAG/Ball configuration for grinding followed by flotation. In the case of Chapada, the mineralogy results in higher-than-normal complexity, notably a significant circulating load both in the grinding and flotation circuits. From an operating perspective, the complexities are controllable, but require careful attention to ensure that circulating loads are effectively managed and gold is not lost to tailings. Chapada created an automation roadmap in 2016 designed to increase plant performance (tonnage, recovery and efficiency). Based on strong potential, the project was fast tracked and within 4 months instruments were installed, control algorithms implemented, and training sessions took place to ensure sustainability at site. This paper will follow the Chapada journey from identifying the opportunities through to implementation and testing.IntroductionYamana Chapada mine is a Copper-Gold mine located in Goiás State, Brazil. Although the mine contains large quantities in Mineral Reserve of gold (4.1 million contained oz as of December 31, 2016), Chapada is primarily a copper mine with copper principally found as chalcopyrite. Accordingly, the processing flowsheet at Chapada is comparable to that of other copper mines with a SAG and Ball mill each partnered with a cyclopack, followed by a flotation circuit. While the overall design is conventional, the mineralogy at Chapada results in significant circulating loads both in the grinding and flotation circuits. This does introduce certain complexities for operating strategies and practices, but, importantly, favourable recoveries and elevated processing rates can be maintained, albeit they need to be closely managed. Plant automation helps in this regard."

Jan 1, 2018

By H. W. Smith, N. Ichiyen

A convenient method for the calculation of metallurgical balances, based on statistical treatment of all available data, is presented. An error analysis is included. Examples show the advantages of the method, and also that such balances are less precise than might be supposed.

Jan 1, 1973

By S. Aram

Concrete reinforcing requires coordination among many roles: structural engineer, estimator, detailer, fabricator, installer and others. The methods used to define and represent concrete reinforcement elements and assemblies in building information models is crucial in determining the efficiency of sharing data among BIM platforms and the effectiveness of using the carried data in production planning, fabrication and site work activities. Starting from the information items that are required to be provided by BIM platforms, as defined in earlier work, we have developed the Industry Foundation Classes (IFC) bound Concepts and Model View Definitions (MVDs) for concrete reinforcement. Furthermore, in coordination with software developers, we propose guidelines for best practices for concrete reinforcement modeling. Implementing these guidelines by software providers will improve reinforcement modeling with regard to various aspects of reinforcement products like geometric representation, placement, and property specifications. The proposed approach is selected as a way to improve functionality of the shared data for production planning, fabrication, project management, and site activities. Guidelines for assigning information to rebar type and instance definitions as well as to rebar elements and assemblies are provided. An efficient method of sharing geometry and property sets among rebar instances of a rebar array is also defined.

Aug 1, 2013

By G. C. Hambleton

"The author has had wide experience in the reclamation of coal from coal mine waste dumps in the United Kingdom.The paper includes such topics as the processing decision and factors affecting processability; method of testing and appraisal; test data interpretation; historical influences in apppraisal; special contaminants and processing difficulties; methods of treatment; review of systems in use and their comparative economics; over-all system economics including excavation, handling methods, recovery system and shale disposal; effluent treatment; environmental considerations; alternatives to processing for coal recovery; light aggregate and cement usage; burned shale heaps; land reclamation; shale deposition for encouragement of vegetation by natural or artificial means; use of tailings fines; the environmental argument for action."

Jan 1, 1972

By C. H. Buck, A. J. Taylor

"In 2015 Vale’s Clarabelle Mill began the process change to enable a higher degree of Cu separation. The flowsheet modification was part of a complete divisional flowsheet change being implemented in Vale’s Sudbury Operations. This paper will centre on some of the Operational Readiness (OR) work, culminating in the commissioning of the circuit in March 2017. The emphasis will be on the implementation of an integrated test plan to prepare for the process flow change through the mill.BackgroundClarabelle Mill (CBM) began making a saleable Cu concentrate in 2006 with the installation of the Cu separation circuit. Typical separation rate was 35-40% of Cu in feed reporting to Cu concentrate based on a target Ni concentrate Cu:Ni target of 0.7-0.8. The remainder of the recovered Cu (55-60%) reported to Ni concentrate and was smelted through the Copper Cliff Smelter.In 2013 a capital project, Surface Facility Upgrade (SFU), was implemented to focus on matching the surface plants capacities with the future mine plan to maximize revenues. This was to be achieved by redistributing the metal flow, specifically Cu, through CBM to increase metal unit content through the Smelter. The amount of redistribution of Cu was determined to be based on maintaining a stable Cu to Ni ratio (Cu:Ni) in the Ni concentrate.The change in Cu:Ni ratio in the Ni concentrate would affect the Sudbury divisional flowsheet, and required process changes across the all of the surface plants. The detail that surrounds the flowsheet changes as a whole will not be discussed, but the outcome of the decisions plays a large role in the operational readiness interactions between the mill, its suppliers and its downstream customers."

Jan 1, 2018

By J-S. Marois, F. Cappucitti, Y. Dodier, D. Downey, G. Matton

"The flotation processes of the Niobec Mine have been affected by a seasonal loss of recovery and a significant increase in reagent consumption over the past few winters. This paper discusses the problem-solving methodology that was used to identify the root causes, to develop solutions and to implement changes that resolved the problem to restore the process to summer-like conditions year-round. Mainly, it was found that the process water was contaminated by phosphates ions, which adversely affected the carbonate pre-flotation, and caused detrimental effects on the subsequent niobium flotation. The phosphate ions were being generated by the process itself, but were consumed by algae in summer conditions. It was determined in laboratory studies that concentrations as low as 5 ppm were enough to affect the circuit and that the multiple additions of process water throughout the circuit was worsening the effect. Also, temperature was found to have an impact on the reagent performance. The performance of the plant was restored by implementing a natural treatment of our process water with a simple cost-free rearrangement of our circuit streams. In addition to that, our extensive geometallurgical program was used to provide ore to the plant restricting phosphate generation in the process. Also, a modification of the collector was developed and introduced in the carbonate pre-flotation that provided improved performance during the periods of low pulp temperature.INTRODUCTION Niobec is one the three major global producers of niobium presently in operation. Situated in the Saguenay-Lac-St-Jean region of Quebec and in operation since 1976, the site produces ferroniobium (FeNb) to be used mainly in High Strength Low Alloy (HSLA) steel, which is known to have better mechanical properties than carbon steel. The Niobec operation consists of an underground mine, a concentrator and a converter plant. The concentrator concentrates niobium-bearing minerals, mainly pyrochlore and columbite, to produce a high-content Nb2O5 concentrate which is then converted to FeNb in the converter plant by an aluminothermic reaction. The Niobec concentrator flowsheet, which has gone through many expansions and optimisation over the years, consists of grinding, desliming, flotation and leaching steps. The flotation steps are numerous, sensitive and difficult to operate due to the non-selective nature of oxide mineral collectors. Thus, the pyrochlore concentration process at Niobec still faces many challenges and is constantly going through periods of continuous improvement."

Jan 1, 2018

By Randy McMeekin, Chris Twigge-Molecey, J. Peter Blake

The project implementation phase, FEL4, is generally a complex undertaking. The project has been approved for construction and the capital has been allocated. At this point the project team comes under significant pressure to meet the safety, schedule, cost, and start-up committments. For the design team the principal tasks are to finalize detailed design, complete procurement, and issue construction contracts. Design activities must be closely coordinated with equipment and material procurement. A clear engineering plan should be based on well-defined work packages to meet construction, commissioning, and startup requirements. A range of review processes by discipline, area, and third parties assure quality. Constructability, safety, and hazard reviews are performed throughout the design process. Three-dimensional models that incorporate extensive databases help to maximize efficiency and minimize errors. Well-managed projects have a clearly accountable design team, rigorous change control processes, and well-defined workflows. Key individuals from the design team participate in commissioning, operator training, and startup.

Jan 1, 2015

By H. C. Boydell

Introduction Situated in the district of South Lorrain, some 16 miles southeast of Cobalt, Ontario, and reached from that centre either by branch line of the T. & N. O. railway or by what, for a mining camp, is a reasonably good road, the Keeley mine, owned by the Keeley Silver Mines,' Ltd., has had its history recorded by C. W. Knight (1). Silver was first discovered in South Lorrain, in Woods' vein, on Keeley property, in 1907, and the Keeley mine has been described by Knight (2) and Bell (3). The total production to February 28th, 1930, has been 10,760,107 ounces of silver and 1,285. 434 pounds (weight) of cobalt.

Jan 1, 1931

The effect of superficial gas rate distribution (Jg profile) on down-the-bank metallurgical response was tested in the rougher-scavenger bank (eight 10-m3 tank cells, 4 roughers and 4 scavengers) at Highland Valley Copper Mine's Cu/Mo separation circuit. Three Jg profiles were tested: (a) as found (i.e., typical practice), (b) increasing decreasing (i.e., increasing from cell 1 to 4 and decreasing from cell 5 to 8), and (c) decreasing-increasing (i.e., decreasing from cell 1 to 4 and increasing from cell 5 to 8). The Jg profile approach proved to be of considerable value. Profile (b) gave the best metallurgical results, i.e., the highest down-the-bank grade/recovery (increase in grade at constant recovery was approx. 3-4% compared to the as found case) and the most efficient Cu/Mo separation (cumulative Cu recovery was reduced by almost half - approx. from 20% to 12%, at 99% Mo recovery). The success of the evaluation prompted the implementation of profile (b). Detailed gas dispersion characterization tests (Jg and Db (bubble size)) showed significant discrepancies between the Jg measured directly (using the McGill University sensor) and the Jg calculated from field instrument readings (volumetric gas flowmeter) and machine dimensions (cell cross-sectional area). Tests were designed to reveal the source of disagreement. It was observed that a significant number of bubbles were not able to float (i.e., they were entrained with the tailings), the evidence appearing to be a significant number of very small bubbles (approx. 200-300 µm) which did not have sufficient buoyancy to rise. Consequently, rather than relying on the field instrument, the evaluation depended on the McGill University Jg sensor, which collects bubbles in a tube near the pulp-froth interface, thus providing significance to the data as the measurements were obtained from bubbles that almost certainly floated.

Jan 1, 2007

The Anglo Platinum Mogalakwena North concentrator was one of the first three hard rock mineral processing applications to utilise a HPGR circuit in preference to a SAG milling circuit. This was driven by the extreme competence of the ore that had given rise to throughput issues on the original South Plant. Despite more than adequate capacity and performance of the individual comminution units, the circuit has struggled to obtain full design capacity. A thorough review of the integrated performance of the circuit revealed a wide range of bottlenecks and underutilised parts of the circuit arising from design issues. Interestingly, the major opportunities lie in materials handling issues and mismatch of loads about the circuit. This paper presents the high-level outcomes and the associated opportunities, and is pertinent to all HPGR circuit designs.

Jan 1, 2012

By W. A. Parks

Stone that may be applied to purposes of construction is available in nearly all the inhabited parts of Canada, the most important exception being the prairie region, but, even here, the deficiency is overcome in many parts by a wealth of glacial field-stones. In many parts of the country, also, the accessible stone is of a quality so poor that brick is more generally used. There is a great difference, however, between stone that 'may be used' and stone suitable for buildings of a monumental type or even for 'trimmings' on the better class of dwelling in the cities and towns. It is in the latter sense that the expression 'building stone' is commonly used. Thus restricted the term includes varieties of sandstone, limestone, and granite, using the latter word in the custom of the quarryman, not only for the true granite of the geologist but for many other igneous rocks as well. Building stone of high quality grades imperceptibly into stone suitable for monuments, particularly in the case of the granites. The present review will deal with building and monumental stone in this restricted sense and will omit marble, although that material has been used to some extent for building. For instance, the Great West block in Winnipeg is built of marble from British Columbia.

Jan 1, 1925

By Junhyun Choi, Allan Gomez-Flores, Chonbuk National University, Siyoung Q. Choi, Gahee Kim, Seungkon Kim

In this study, to confirm the effect of depletion attraction on the flotation, we theoretically and experimentally investigate the effect of the depletion attraction force on flotation. While varying the concentration of the depletion agent (polyethylene glycol), three different systems are studied: pure malachite, pure silica, and a 1:1 mass ratio of malachite and silica binary system. We find that recovery increases significantly as the concentration of the depletion agents increases for all three systems, as the depletion agent facilitates the adsorption of the particle on the bubble surface. However, the recovery suddenly decreases in a certain concentration range, which corresponds to the onset of the decreased surface tension when high concentrations of the depletion agent are used. This non-monotonic overall recovery trend implies the surface adsorption of the depletant on a surface. The decreased surface tension of the air/water interface suggests that the recovery rate is lowered due to the adsorption of the depletion agent to the bubble surface, acting as a polymer brush. Based on our observations, we conclude that the depletion force can greatly improve particle adsorption, as predicted in the accompanying theory paper, while simultaneously the adsorption of the depletion agent on the bubble surface plays an important role because it hinders particle adsorption. We also perform experiments in the presence of a small amount of a collector, sodium oleate. An extremely small amount of the collector leads to the increase in the overall recovery, which eventually reaches nearly 100 percent. Nevertheless, the grade worsens as the depletant provides the force to silica particles as well as target malachite particles.

Jan 1, 2016

By W. N. Roman

This paper will examine the challenges involved in ventilating and cooling South African mines, with particular emphasis on solutions to the issues of heat (generally associated with depth), mechanization and energy efficiency. Comparisons will be made with other international mining areas. Some of the deepest mines in the world are to be found in the South African goldfields. The Mponeng mine is approaching 4,000 m below surface, with virgin rock temperatures (VRT) of between 60°C and 70°C. Mining at these depths has only been possible with the use of large refrigeration plants supplying cold air, water and ice to the workings. In the Bushveld Igneous Complex, where most of South Africa?s platinum mines are located, similar VRTs are being experienced at significantly shallower depths. This is due to the different geothermal properties of the host rock between the two areas. Existing mines are being forced to go deeper and new underground mines are being planned and constructed in other areas with widely differing thermal conditions. South African metal mining has traditionally been labour intensive for historical reasons as well as for the narrow tabular nature of many ore bodies. Due to cost pressures and labour problems, some mines have been investigating the possibility of using mechanized equipment, both diesel and electric, to increase production and to improve efficiency. Studies have been carried out to determine the effect of the additional equipment on the overall ventilation system and some of the conclusions are discussed. The use of diesel equipment adds heat and pollutants to the ventilation air but, although electrical equipment has a lesser effect on the ventilation systems, it is generally less favoured due to claims of lower flexibility/manoeuvrability. Mechanization holds the promise of more concentrated mining activities but, with higher localized ventilation and cooling needs. Systems which will control the provision of air and cooling more effectively are required and are being implemented. In the 1990s and early 2000s, the South African economy experienced significant growth which was not matched by the growth in infrastructure. Consequently, at present there is a shortage of electricity generation capacity which affects large industrial consumers, including mines. Increasing levels of heat and mechanization will require more electrical energy for ventilation and cooling. There are many initiatives underway to save power or to shift consumption to periods of national low demand and these will be described.

Aug 1, 2013

By B. M. Monaghan

"The developments of the 1950s and 1960s have seen Canada become an international source of iron ore, trading in all geographical areas and hemispheres. Canada's production will significantly increase in the next decade. However, although the outlook is bright, iron ore producers cannot be complacent. Instead, we must weigh the factors that have brought about the development of the Canadian iron ore industry and examine the probable changes for the next decade that will affect its growth.Looking ahead in the 1970s, competition will be severe. Pressure on prices will continue as new sources of supply bid for long-term contracts and as steel producers continue to develop mines around the world. Rising costs will make these pressures more severe. We must balance the growth of the world's steel makers with the emergence of new supplies of iron ore. The iron ore industry is now part of a new era in which demand and supply are intermeshed, and the developments around the world are acting on the Canadian iron ore industry's future."

Jan 1, 1971

By Martha Gellner, Lutz Wuschke, Hans-Georg Jackel, Urs A. Peuker

"Electric vehicles are an alternative to the existing combustion engine driven cars. According to the EU Battery Directive a substantial recycling rate of at least 50 wt.-% has to be met for aged batteries since 2006. Existing recycling techniques are based on energy intensive pyro- and hydrometallurgical process, which are not able to recover all components. Aluminum and lithium for instance are slagged. The EU-Project “ABattReLife” investigated possibilities for a mechanical processing in order to create a sustainable process and a closed material loop from grave to cradle. After a sufficient liberation of the Li-ion batteries, components like the doped carbon black fraction (mainly lamination of electrode foils), the separator foil and the housing material can comparatively easily be separated from the other components by screening and air sifting. The remaining mixture consists of anode and cathode foils which have a similar free-settling ratio and are more difficult to separate from each other. A second comminution and compaction step modifies the particle size and shape as well as the degree of delamination. These changes influence the density of the electrode foils in order to improve the separation efficiency. Yield and purity of the generated metal concentrates were parameters to show if the separation was successful. The specific energy consumption for the different methods of processing was estimated in order to benchmark the cost-benefit ratio for each one.The studies have been accomplished with a zig zag sifter (model TUBAF), a hammer mill (model HM 340 Jehmlich) and with a Petkus-Sifter. Finally a process flow sheet was developed for a Li-ion battery recycling plant in pilot scale."

Jan 1, 2016

By M. Y. Williams

Introduction During the economic investigation of Pacific Great Eastern Railway subsidy lands, the P.G.E. Survey of Resources made a geological and mineral survey of a large part of the valley of the Peace river as included in the Province of British Columbia. The immediate valley of the Peace river was surveyed from the mountains to the Alberta boundary; the valley of the Pine river was surveyed throughout; and the Dominion block, 70 miles square and lying astride the Peace river, westward from the Alberta boundary, was very carefully surveyed. The writer was in general charge of the field work, and spent half the field season of 1929 and the field season of 1930 in the region . J. B. Bocock, however, did the major part of the work, spending two seasons, 1929 and 1930, in the area. General Conclusions The rock formations within the area discussed are all sedimentary and range in age from pre-Cambrian to recent. As might be expected, the minerals are in the main non-metallic, coal being by far the most important. Favourable conditions exist for natural gas occurrence, and suitable structures for petroleum concentration occur, although the high carbon ratio of the coals sheds considerable doubt upon the actual occurrence of oil in the area. Materials of minor interest are ochre, calcareous tufa, marl, limonite, gravel, and building stone.

Jan 1, 1934

By G. R. Cope, C. D. Spence

"The Mac porphyry molybdenum prospect is located 100 km east of Smithers in central British Columbia. The identification of anomalous levels of molybdenum, copper, and silver in three adjacent lakes, sampled during a regional lake sediment survey, lead to the discovery of molybdenite mineralization in float. Subsequent magnetic and soil geochemistry surveys, together with prospecting and mapping, located the source of the float. Mineralization is hosted by a leucocratic granite stock of the Upper Jurassic to Lower Cretaceous Francois Lake Intrusions which has intruded Carboniferous and Permian Cache Creek Group volcanic and sedimentary rocks. The stock measures 500 m by 300m at surface and is mineralized throughout. Sulphide mineralogy is simple and consists of molybdenite with minor pyrite and local chalcopyrite. Molybdenite occurs within fractures and as selvages along quartz stockwork veins and is best developed near the margins of the stock.Known mineralization is coincident with distinct soil geochemistry and magnetic anomalies. Two additional areas of the property display similar features and these remain to be tested.IntroductionThe Mac property is situated in the Babine Lake area of central British Columbia on NTS map sheet 93K/13E, approximately 100 km east of the town of Smithers (Fig. 1). The property lies on the western margin of the Hogem Range at the northern tip of the Nechako Plateau. The centre of the claim block lies at 54°51 ' 30""N and 125 °34 '30""W.Topographically, the claims are characterized by gently rolling hills ranging in elevation from 900 m to 1500 m. Slopes are forested with tall conifers and underbrush is minimal. Flat-lying areas are swampy with tall grasses and scrub brush.Presently, the property is only accessible by helicopter from bases located in Smithers and Fort St. James. Recent road construction by the British Columbia Forest Service has brought road access from Burns Lake to within 5 km due south of the property. It is expected that in the near future, roads will be advanced into the claim area to facilitate logging of mature timber."

Jan 1, 1995