Search Documents

By M. Gyenge, O. F. Coates, K. Barron

"It is suggested that artificial supports might be used to increase, with safety, the angle of hardrock open-pit slopes. Guidelines for designing such a support system, based on a simplified analysis, are given. The installation, construction and instrumentation of a trial support system is described and a breakdown of the construction costs is given. On the basis of this cost analysis, the economic benefits derived from reduced waste-rock excavation are compared with the support costs for a typical mine. In an example, it is shown that the slope angle in an open-pit mine 500 ft deep, with benches 50 ft high by 30 ft wide, could be safely increased from 37Yz degrees without support to an optimum of 53 degrees with support. In this case, the support costs would be approximately $900 per linear foot of pit wall and the savings due to decreased excavation of waste rock (at $0.34/ton) would be approximately $1,900 per linear foot, yielding an increased margin of profit of approximately $1,000 per linear foot of pit wall. This figure could be increased to $6,000 per linear foot if the steeper slope were used to extract more ore.More than 50 per cent of the support costs are accounted for by diamond-drilling the holes for the deep cable anchors. The use of percussion drills for this purpose would seem to offer a means of significantly reducing the support . costs and thus further increasing the profit margin available."

Jan 1, 1971

By Zihe Ren, Edouard Asselin, Marcus Tomlinson, Tianbi Zhang, Jing Liu

"Raman spectroscopy is used to quantify the extent of disorder in the carbonaceous matter associated with preg-robbing ores. Previous studies of Goldstrike ores showed that the height and width of the peaks for the “D” (disordered) and “G” (graphite) bands, the so-called “Raman ratio” had a strong correlation to the preg-robbing value (PRV) measured for various ore samples. A brief literature review on Raman spectroscopy as it applies to preg-robbing ores is presented. Further, recent studies, presented here, have shown no correlation between the Raman ratio and the PRV for a wide variety of ores. This suggests that the extent of organic carbon crystal disorder is not the main factor in determining preg-robbing characteristics.INTRODUCTION Preg-robbing may arise from natural carbonaceous materials in the ore. Several mechanisms have been proposed in the past decades including a physical sorption process by the carbonaceous matter, or via the reduction of aurocyanide at the mineral surface (Abotsi & Osseoasare, 1986; Afenya, Osseoasare, & Abotsi, 1983; Tan, Feng, Lukey, & Van Deventer, 2005). Nevertheless, the mechanisms of preg-robbing remain poorly understood. Understanding the nature of the preg-robber is of practical importance for the selection of a suitable treatment process. Fine carbon particles in the ore have been recognized as preg-robbers due to their similarity to the activated carbon used in the carbon in leach (CIL) or carbon in pulp (CIP) processes. Previous research has illustrated that the activated carbon (also referred to as amorphous carbon in some literature) has a much higher absorption ability than pure graphite with high crystallinity (Adams & Burger, 1998). Adams et al (Adams, Swaney, Friedl & Wagner 1996) concluded that carbonaceous matter is largely responsible for the overall preg-robbing capacity of a given ore. However, the mechanism of carbon preg-robbing was still not clear mostly due to the complexity of amorphous carbon and its behavior in different solution matrices, and at different pH and temperature (Adams, 1990, 1993)."

Jan 1, 2017

By Ian R. Morrison

"Abstract - The Izok Zn-Cu-Pb-Ag volcanogenic massive sulfide deposit is located 265 km south of Kugluktuk (Coppermine), Nunavut Territory, Canada, in the west-central Slave structural province. The Izok deposit is owned 100% by Inmet Mining Corporation and represents one of the largest undeveloped zinc-copper resources in North America. The Izok deposit is hosted within and near the top of a thick sequence of predominantly felsic pyroclastic rocks of late Archean age. The hanging-wall stratigraphy includes additional felsic volcaniclastic rocks, andesitic and basaltic flows, thin sulfide-rich iron formations, and turbiditic sedimentary rocks. The felsic volcanic rocks are intruded by intermediate dikes and sills, followed by gabbroic dikes and sills. Both intrusive suites are interpreted to be volcanic feeders to the overlying flows. All lithologies are subsequently cut by younger, irregular, granitic pegmatite and diabase dikes. The volcanic and sedimentary rocks are regionally metamorphosed to pyroxene hornfels grade. The massive sulfides occur within a large (kilometer-scale) Na-depleted sericitic alteration zone. The immediate footwall and hanging-wall rocks to the deposit are characterized by zones of muscovite- biotite-sillimanite, lesser chlorite-biotite-cordierite, and locally intense silicification and sodium metasomatism. All lithologies have been affected by younger Ca-metasomatism. As currently defined, the Izok deposit comprises a cluster of five complexly zoned composite lenses: the Northwest, North, Central West, Central East, and Inukshuk lenses. The first four lenses are amenable to open-pit mining, whereas the Inukshuk lens will require underground development. The total indicated mineral resource presently stands at 16.5 million tonnes with a grade of 2.2% Cu, 11.4% Zn, 1.1% Pb, and 60 g/t Ag. Inmet Mining Corporation is presently reviewing the economic feasibility of developing the property."

Jan 1, 2004

By A. Tylczak, C. Norman, C. Shook, S. Loif

"There are a lot of good reasons to manage energy use at mining operations. Optimizing process energy use reduces operating costs. Tracking energy use can help identify unplanned process changes or malfunctioning equipment early, which allows problems to be corrected promptly.Sacré-Davey Engineering in Vancouver has performed over 50 Energy Management studies for various industries including: mining, pulp and paper, oil and gas, etc. Energy Management programs can be used to identify energy reduction opportunities, assess project feasibility, complete equipment selection trade-offs, as well as to monitor and manage energy costs. Benefits of energy management programs are reduced energy costs, reduced maintenance, and increased plant automation. Additionally, energy management can provide access to utility incentive funding and quantify savings which can greatly improve the return on investment of potential projects.Energy management studies are funded by many Utility programs across Canada. There are various programs available for existing plants energy audits, project feasibility studies, new plant design reviews and energy monitoring and targeting, etc. There are capital incentives available which can significantly reduce payback period.This paper discusses how energy management can be used to support mill/mine operations groups, maintenance programs, as well as expansion or green field projects. This paper will also provide an overview of Canadian Utility companies programs and how they can assist mining companies.IntroductionThere are a lot of good reasons to manage energy use at mining operations. Optimizing process energy use reduces operating costs. Tracking energy use can help identify unplanned process changes and identify malfunctioning equipment early, which allows problems to be corrected promptly."

Jan 1, 2015

By R. V. Typliski, G. J. Labarre

"Hudson Bay Mining and Smelting Co., Limited, Flin Flon, Manitoba, Canada, has developed a metallurgical wastewater treatment system employing two-stage lime neutralization, sludge recirculation and conventional mechanical thickening.Laboratory investigations, initiated in 1970, led to the construction of a pilot-scale minewater treatment plant, at Schist Lake Mine, in early 1971. This plant, treating 600 cubic meters/day wastewater containing 30-60 mg/l zinc, demonstrated metal extraction efficiencies of 99% under normal operating conditions.On the basis of this pilot work, a second pilot-scale treatment system was established in 1975 at the Flin Flon metallurgical plant to treat zinc refinery process waste water. Through numerous improvements, including automatic control equipment, the system has evolved to a full-scale operation capable of treating 800 cubic meters/ day wastewater containing 4-11 gm/l zinc. Treated effluent contains 0.2-20 mgll zinc. Hydroxide sludge produced returns to the metallurgical process for recovery of metals while clarified effluent discharges to waste.With the system, Hudson Bay Mining has achieved its original goal: the reduction of environmental contamination, while realizing ii return from metal recovery."

Jan 1, 1980

By K. Winterton, Carruthers. J.

"Attempts have been made to produce hardened structures of a pseudomorphic type in various carbon and alloy steels. In order to obtain martensite with a fine distribution of cementite, an initial structure of fine lamellar or nodular pearlite is required; this may be obtained by conventional means. This is followed by partial austenitization and quenching.Two methods have been tried to induce partial austenitization:(a) A resistance (direct current) heating method involving rapid entry into the austenite field.(b) A new method, described as the ""threshold"" technique, involving homogenization of temperature just below A 1, followed by entry into the austenite field; two furnaces are required.The resulting structures have been examined for microstructures, hardness, tensile, and impact values. The tensile properties are comparable with those obtainable by conventional treatment methods. Impact values are disappointing, but this is explainable from the nature of the manifold changes occurring."

Jan 1, 1960

By G. S. Hume

Introduction O WING to the mineral discoveries which have recently been made in the Great Bear Lake region and the possibility of the need for fuel for transportation and development, it seems.timely ro review available information regarding the oil prospects in the vicinity of Great Slave lake and Mackenzie river, where a vast area is underlain by Palreozoic and younger sediments that undoubtedly are petroliferous. Exploratory surveys were carried out in this area by the Geological Survey and others in the latter part of the 19th century, but it was not until 1920, when drilling for oil actually began, that any serious attention was paid to the oil prospects. This is readily accounted for by the remoteness of the region, the lack of quick transportation facilities, and the shore summer season. Numerous and copious oil seepages had been reported, however, from widely separated localities, and interest was stimulated by the knowledge that these occurred in Devonian strata which had given a remarkable record of sustained production of high-grade oil in the oil-fields of southwestern Ontario. . Accordingly, during the four years 1920 to 1923, inclusive, several parties sent out by the Geological Survey made as thorough an investigation of various parts of the area as seemed warranted at that time, and from these surveys most of our information regarding the details of the stratigraphy is derived. In such a large area, it is inevitable that the lithology and thickness of rocks of the same age would show wide variations, and hence it should be recognized that conditions as regards oil prospects in the vicinity of the west end of Great Slave lake are quite distinct from those that occur near Fort Norman, 400 miles farther to the northwest, and these again are in all probability quite different from those in the less well known Arctic Red River area, 250 to 300 miles still farther north.

Jan 1, 1932

By A. Osouli, B. Moradi Bajestani

"Increase in permeability of rock mass is vital for both petroleum and geothermal applications. Hydraulic fracturing is a common method to create and increase the permeability for production. Due to the complexity of fracture propagation in a naturally fractured medium, understanding the interaction between hydraulic fracture (HF) and natural fracture (NF) is of great importance to optimize the fracturing process. The possibility of interaction between HF and NF is partly a function of orientation. Various scenarios are predictable for hydraulic fracture regarding the intersection with NF such as being arrested by NF, crossing NF or crossing the fissure while injecting water into it. Different parameters such as geomechanical and geometrical properties of surrounding rock mass, the operational parameters such as injection rate and the angle between created hydraulic fracture and natural fracture (approach angle) can affect the result of hydraulic fracture and natural fracture intersection. In this paper, using a series of flow-coupled Distinct Fracture Network (DFN) simulations, hydraulic fractures were analyzed to investigate the influence of the aforementioned parameters on the hydraulic fracture propagating. Results show that the most significant parameters affecting the interaction of natural and hydraulic fracture are orientation of the intersection as well as injection rate. The interaction and fracture propagation in NF and HF intersections are also studied and discussed in detail.INTRODUCTIONThe hydraulic fracture technology has substantially changed the oil, gas and geothermal industries. With the help of this technology, extraction of fossil resources from tight shale reservoirs will be economical, feasible and sustainable. Due to presence of massive oil and gas trapped in these reservoirs, this technology has been the center of attention for the past 40 years (King, 2012). Hydraulic fracturing is the process in which high pressure water is pumped into shale unconventional reservoirs with low to ultralow permeabilities. With this process paths are created in these mediums for delivering oil and gas to horizontal wellbore and increase the surrounding rock medium permeability. Economical and sustainable stimulation of these tight reservoirs is highly dependable on our understanding in regard to fracture propagation in the highly complex rock medium. Hydraulic fracturing process in rock mediums with preexisting natural fractures is more complex because of the high possibility of Hydraulic Fracture (HF) being arrested or deviated by Natural Fracture (NF). Also, HF and NF intersection can influence the required pumping pressure, injection rate, the outcome of horizontal wellbore and the affected geological underground zones. Since the 1950s, numerous studies have been conducted to predict and plan fracture propagation with the help of modeling and simulation methods. Having a thorough and accurate prediction of fracturing process will not only prevent stimulation of unwanted geological zones or pollution of aquifers, but also will improve the efficiency of the fracturing process. Previously, several studies have been conducted in order to investigate and analyze the interaction of hydraulic fracture and natural fracture (Cottrell, Hosseinpour, & Dershowitz, 2013; Doe, Lacazette, Dershowitz, & Knitter, 2013; Shakib, 2013; Zhang & Jeffrey, 2006)."

Jan 1, 2015

By D. Yu, T. A. Utigard, M. Barati

"Sulfation roasting of nickel concentrate to generate water-soluble metal sulfates was investigated as an alternative process to smelting for the recovery of valuable metals. The kinetics of dissolution of various species of the calcine in three leachants was studied; hot water, dilute HCl, and concentrated HCl. The results indicated that dissolution of sulfates by hot water at 90 ºC is achieved within 30 minutes. In order to increase the recovery of the valuable metals, acid leaching is necessary due to the existence of ferrite in the calcine.INTRODUCTIONInvestigations on the sulfation roasting of nickeliferous sulfide ores or concentrates were mainly carried out in 1950’s to 1990’s to generate water soluble non-ferrous metal sulfates followed by metal recovery by leaching (Stephens, 1953; Thornhill, 1954, 1961; Fletcher and Shelef, 1964a, 1964b; Fletcher and Hester, 1964; Frankiewicz, 1977; Norrgran, 1983). Commercialization of the sulfation roasting process was only performed by Falconbridge Ltd. (Thornhill, 1961; Boldt, 1967), which employed a sulfation roast process on nickeliferous pyrrhotite at 680 oC where Ni, Cu, and Co were leached and Fe2O3 was produced for the iron industry. In 1965, 118,342 tons of pyrrhotite was processed, however because of the huge SO2 emissions (no acid plant) relative to the nickel production and the poor economics, this plant was shut down.Nickel production from sulfide ores via pyrometallurgical means, especially the electric furnace smelting process, is a major emitter of SO2 to the environment and a big energy consumer (Warner, Diaz, Dalvi, Mackey, Tarasov and Jones, 2007). Nowadays, due to the more stringent environmental regulations as well as the need to reduce energy consumption, metal production by sulfation roasting is gaining more attention as an alternative process to smelting. The main focus of this paper is to investigate the extent and rate of leaching of valuable metals from the sulfation roasted nickel calcine, aiming to maximize the metal recovery and minimize the dissolution of iron species."

Jan 1, 2012

By George J. Thompson

This pa per deals with the internal characteristics of steel and its response under cold northern temperatures. General maintenance procedures and specific repair techniques are covered.

Jan 1, 1973

By Philippe Caudal

This paper presents a case study in which a slope failure was observed on the west wall of the LAB Chrysotile mine in the vicinity of the main ramp in January 2010. Airborne LiDAR results were used to evaluate slope geometry before and after the failure occurred. Back analysis of the failure was performed to assess rock mass properties at the slope scale using various numerical techniques: limit equilibrium, finite elements and fracture networks. The various approaches correlated well with field observations.

Aug 1, 2013

By K. Ghyselbrecht, R. Swennen, Y. W. Chiang, V. Cappuyns, R. M. Santos, T. Van Gerven, B. Meesschaert

Heavy metal contamination from mining and metallurgical activities of aquatic systems poses significant risk to the environment and human populations. The investigation of the distribution and immobilization mechanisms of heavy metals in sediments and soils has recently attained high priority. Different remediation methods can be employed to suppress or eliminate these contaminants. A tailored approach using both commercially available and in-house made adsorbents to rem ediate a heavy metal contamination site due to historical metallurgical activities in north Belgium is studied in this paper.

Jan 1, 2011

By F. H. Samuel, P. Burke, F. Mucciardi, J. Gruzleski, S. A. Musmar

A new thermal analysis technique has been developed and tested. It utilizes the enhancement in heat transfer characteristics associated with a recent advancement in heat pipe technology. Heat is extracted from a liquid sample of a melt taken in-situ within a vessel or furnace. The rate of heat extraction is such as to cause the sample to solidify. The technique was tested in both laboratory scale and industrial scale (Grenville Castings, Perth, Ontario). A 356 Al Alloy, subjected to various melt treatments was used to perform the tests. Classical thermal analysis was also performed simultaneously using a preheated graphite cup and at the same melt conditions. The comparison showed the potential of the new technique over classical thermal analysis. The major advantages of the new method are that it conducts the analysis inside the melt (i.e. a physical sample is not removed from the melt), it consumes less time and the cooling rate can be precisely controlled during the solidification process. Moreover, the resolution of the results is better than that of conventional techniques. Aluminium

Jan 1, 2006

By V. I. Lakshmanan, D. A. Mackie

"1. INTRODUCTIONIn the past two decades, low-grade gold and silver ore bodies in the United States have been exploited by heap leaching, primarily with sodium cyanide solutions. This method has proven to be a viable alternative to conventional milling due to its low capital and operating costs. Successes have been made, particularly in Nevada, where ores are well oxidized and the climate is conducive to this method. in recent years, heap leaching has been tried in northern latitudes with some success, however, in using this method, operators face more severe limitations than do their neighbours to the south.This paper evaluates the limitations of heap leaching with particular emphasis on northern climates and introduces an alternative method to recover precious metal values in a continuous vat. This proprietory technology, known as the Mackie Vat Leaching Jig, shows promise, with improved gold recovery and potential to operate in cold climates.2. WHAT ARE THE LIMITATIONS TO HEAP LEACHING?Heap leaching of non-refractory ores is subject to the following limitations:1. Minimum amount of free gold and nuggets in the ore.?. Minerology of the ore--accessibility of gold to lixiviant.3. Minimum particle size and size distribution of crushed product to allow percolation of lixiviant through the heap.4. Minimum amount of clays or clay-like slimes that can cause coating of ore particles and channelling of lixiviant.5. Minimum strength of ore particles or agglomerations to allow economic height of heaps to be built.6. Amount and suitability of real estate.7. Amount and type of precipitation.8. Ambient temperatures.9. Possible poorer lixiviant diffusion.10. Possible lower oxygen content in dissolved cyanide solution with higher heaps, particularly with ice and snow cover."

Jan 1, 1989

By M. Melashvili

"The SART Process was introduced to the gold mining industry in the late 1990s and several commercial plants were built over the following 10 to 15 years. Most of these plants have operated well and enjoyed plant performance in line with expectations based on the underlying chemistry of the process. However, two of the plants have consistently suffered from high reagent consumption and poor product quality, which has motivated a re-examination of the process fundamentals in the hope of understanding the reasons for poor performance when it occurs, and developing mitigating strategies.This testwork along with a review of the relevant literature has demonstrated that the amount of sulphide added to the primary reactor, relative to the copper concentration, is the most critical parameter dictating plant performance, with pH and residence time important secondary factors. The primary product in the SART Process is synthetic chalcocite, Cu2S, and the stoichiometric requirement for sulphide addition is therefore 0.5 moles per mole of copper in solution. Testwork shows that when sulphide is added in excess of this amount (generally with the express purpose of lowering residual copper in solution) it not only fails in its intended purpose, but can have a negative impact on the settling and filtration characteristics of the copper sulphide product, as well as the final product quality. Moreover, these problems are exacerbated the higher the selected operating pH in the pH 3 to 5 range, and the longer the residence time of slurry in this pH range.Freshly precipitated copper sulphide compounds are known to be very fine and slimy, with poor settling and filtration characteristics. It is therefore important to engineer the SART Process in such a way as to encourage growth in the average particle size of the precipitate crystals. This was the rationale for recycling a portion of the thickener underflow to the primary reactor when the SART Process was developed. The theory of crystallization predicts that compounds of extremely low solubility, such as chalcocite (Cu2S: KSP = 10-48), are likely to experience growth in crystal particle size through aggregation rather than heterogeneous nucleation. On this basis, the SART practice of recycling a portion of thickener underflow to the primary reactor in the commercial plants is unlikely to lead to crystal growth via nucleation, and could in fact promote breakage of the aggregates that formed in the thickener. Recycling thickener underflow could therefore have the opposite of the desired outcome. The result of testwork that is reported here lends credence to this theory and questions the wisdom of recycling in the SART process.There is evidence to suggest that operating the copper sulphide thickener in the SART Process without flocculants may be beneficial. Thickener underflow densities could improve from the current 10 - 15% range to 40 - 50%. This will not only reduce the flowrate of slurry to the filter, but the filtration properties of the slurry (filtration rate, filter cake moisture content) will also improve. This is one of the most critical engineering and design aspects of the SART Process, and the achievement of high solids density in the thickener underflow will not only improve the health and safety aspects of the operation, but also has the potential to lower capital costs and improve the quality of the final product."

Jan 1, 2016

By Steve McAlister, Colin Sprake

"Enhanced gravity concentration machines have been applied successfully in the following areas of precious metal recovery flowsheets:1. Primary Grinding Circuits2. Shaking Table Tailings3. Pre-Concentration of Leach Feed4. Flotation Concentrates -•, Flash•, ConventionalAlthough great progress has been made, the ability to produce directly smeltable concentrates still remains elusive. Even without this ability, centrifugal concentrators are finding wideningapplications in precious metal concentration:1) PRIMARY GRINDING CIRCUITSEnhanced gravity concentration technology has largely replaced jigging as the technology of choice in precious metal grinding circuits worldwide. The benefits of using a centrifugal field to concentrate both coarse and fine gold are well documented but the placement of these machines within grinding circuits is still evolving. Conventional wisdom dictates that the best location for enhanced gravity machines is cyclone underflow on account of the elevated grade found in this stream when compared to cyclone feed or overflow. Plant operating experience at both large and small scale indicates that there are compelling arguments to place ENHANCED GRAVITY MACHINES on cyclone feed instead. At least two new plants, presently in the detailed design stage will incorporate gravity circuits that treat mill discharge or cyclone feed, Teck Cominco’s Pogo and Newcrest’s Telfer Expansion.Current Conventional PracticeThe current stream of choice for enhanced gravity concentration within grinding circuits is cyclone underflow although recent information indicates a swing toward cyclone feed. Here are some of the arguments for treating a portion of cyclone underflow:"

Jan 1, 2003

By José J. Suárez

As pressure grows for commodity pricing, new mines are more difficult to develop, the stock markets demand better financial returns from mining companies, resources for the developing and operations are scarce, and developing countries in Asia, and Africa demand more metals, it is important that mining companies effect better utilization of capital to develop capital projects. In the last few years, the costs for Capital projects have been impacted by the following factors:

May 1, 2013

By Jose R. Hernandez-Aguilar

"Three models to predict the effect of bubble size (Db) on metallurgical response were tested in a pilot-scale flotation column at Teck Highland Valley Copper mine. The column was fed with slurry collected from the Cu/Mo separation circuit. The first model was the one developed by Gorain et al. (1997), which assumes that the collection zone rate constant (kc) is inversely proportional to Db. The second model was the one proposed by Hernandez-Aguilar et al. (2010), which considers kc as an inverse square function of Db. The third model was the one developed by Yoon and Luttrell (1989) which provides expressions to describe the efficiency of particle collection (E) based on first principles. The results showed a significant bias between experimental and predicted data using the model of Gorain et al. (1997), possibly reflecting the model’s inability to explain the impact of bubble size, bubble rise velocity and flow regime on E. The model of Hernandez-Aguilar et al. (2010) well described the experimental evidence. The model of Yoon and Luttrell gave accurate and unbiased predictions. However, Yoon and Luttrell’s approach calls for a criterion to determine whether the flow regime is potential or intermediate, a subject that requires more fundamental research.INTRODUCTIONParticle collection, i.e., bubble-particle collision followed by attachment, is the basis of flotation. In a quiescent environment (such as the one observed in a column, or away from the impeller in a mechanical cell), a collision event can take place as long as the “degree of turbulence” caused by the rising bubble does not prevent particle and bubble to flow in close proximity. Upon collision, the particle slides on the bubble surface for a period of time. If the particle is hydrophobic, attachment occurs when the “sliding time” is longer than the “induction time”, which is the time required to thin and rupture the intervening liquid (usually water) film forming a three-phase contact angle. While the induction time is largely influenced by the degree of hydrophobicity of the particle, the degree of turbulence is governed by the bubble size. Generally, direct control of bubble size is not exercised by most mineral processing practitioners, in spite of its obvious importance. Studies to model the effect of bubble size on particle collection using fundamental approaches have been conducted (e.g., Anfruns and Kitchener, 1977; Webber and Paddock, 1983; Yoon and Luttrell, 1989; Dai et al., 1999). However, these models have been validated under highly idealized laboratory conditions (micro-scale experiments using single minerals and uni-sized bubbles), far from resembling those existing in practical industrial applications. Fundamental studies to interpret the effect of bubble size on particle collection in industrial environments are largely absent in the literature. Partly because of this lack of practical knowledge, many mineral processing practitioners perceive laboratory “bubble size” studies to be valuable academic exercises, but not something that can be directly applied to daily production issues."

Jan 1, 2011

By S. Akhlaghi

In many electronic/optoelectronic devices, interaction between the metal stack and solder is undesirable. If a reaction happens, a nonuniform joint containing spikes and voids is likely to form and as a result the heat dissipation deteriorates significantly, which in turn, leads to the degradation of the bond. In the present work the interaction between Ti/Mo/ Au metallization system, which was sputter deposited on AlN substrates, and Pb-Sn solder was studied by using scanning electron microscopy (SEM). Also, an EDX system was used to trace the changes in chemical composition of the layers after solder tests. The microstructural examinations show that the Ti and Mo layer from the Ti/Mo/ Au metallization system are not impermeable enough and thus Ca from the surface of the substrate moves all the way up to the interface of Au/Mo and forms an intermetallic at the interface, which grows over time.

Jan 1, 2006

By John H. Nicholls

In this paper, Imperial Oil Limited reports briefly on the drilling by contract rigs of twenty-nine slim holes in the Virden, Smiley, and Souris Valley areas. The investigations showed that slim-hole penetration rates, as a result of careful control of drilling variables, can approach those achieved with 7 7/8-inch bits. It is concluded that slim-hole drilling is acceptable for development or exploratory work. Imperial also reports on the completion techniques and equipment that have been developed on twenty-seven tubingless 2 1/2-inch casing completions. Indications are that the method is economically desirable where excessive gas or water production is not anticipated.

Jan 1, 1958