Search Documents

By Jack Taggart, Chris Barker

Pile load testing strategies for large infrastructure projects and multi-phase building developments have historically justified cost and programme benefits for undertaking advance preliminary and working pile load testing. However, more recently piling and pile load testing strategies have included assessment of the embodied carbon to understand and present the carbon savings that can also be achieved. This paper gives an overview of the factors contributing to carbon and emissions in the construction of bored pile foundations and presents the methodology taken in assessing embodied carbon as part of the pile load testing strategy for a multi-phased building development in London. Potential embodied carbon savings for various bored pile types and load testing strategies are discussed alongside alternatives and other considerations including pile re-use and carbon offsetting to inform continual improvement for future projects.

May 1, 2022

By Mike Muchard

STATNAMIC load testing augmented with embedded instrumentation has been successfully used to obtain structural and geotechnical design information on large diameter spun cast concrete cylinder piles on many large marine construction projects. The paper focuses on one particularly interesting large marine project involving a new bridge to St. George Island, Florida where instrumentation and STATNAMIC load testing was used in conjunction with static load testing on high capacity piles. The information presented includes embedded instrumentation measurements taken during pile fabrication (post-tensioning), during pile driving, during static load testing, and STATNAMIC load testing. As much of this data is the first of its kind on concrete cylinder piles, it is exciting to present the foundation industry with this additional insight as to the behavior of this pile type and the accuracy of the methods used to test them.

Jan 1, 2013

By Sunil S. Basarkar, Vinothkumar S

Ground Improvement Techniques serves to improve various engineering properties for supporting various foundations. These may be undertaken either by conventional or advanced methods. The Controlled Modulus Column (CMC), also known as Rigid Inclusion is a soil improvement technique to reduce the total and differential settlement by using semi-rigid soil reinforcement columns. The CMC technique can be executed by displacement or non-displacement methods. It does not aim to bypass the compressive layer or to install a pile that will directly support the entire load from the structure. Principle of the technique is to introduce a load transfer platform between the head of the column and structure and transform a uniform load into soil. Initially, the structural load transmitted into the soil generate the settlement greater than CMC piles. When the settlement between the soil and column became equal at neutral point, maximum structural load shall be balanced by the positive friction and tip resistance to stabilize the foundation without exceeding the allowable settlement limit. This paper describes the behaviour of soil reinforcement with CMC column and their installation process with reference to a project at the Dry Bulk Terminal Port, San Pedro- Abidjan (Western Africa). Methodology of CMC, requirements of Ground Improvement, arrangements and outcome of this method are presented in this paper.

Sep 1, 2022

By Daniel P. Stare, Lucian P. Spiteri, Christopher M. Hallahan, James C. Myers

Buckeye Lake Dam was substantially remediated between 2015 and 2018 as a result of unacceptable dam safety performance. A permanent seepage cutoff, consisting primarily of a soil mixed cutoff wall (SMCW) with occasional sections of steel sheet piling, was constructed along the dam alignment. Closures were required at the terminus of the soil mix elements with existing structures or coffer cells, and at locations where new sheet piling was constructed parallel to the new soil mixed cutoff wall, creating a short circuit seepage path. The original proposed design to construct these closures included permeation grouting methods with chemical grouts. However, a combination of multiple chemical grout types, multiple grout pipes, and an extensive post-grouting verification program was required to ensure the design intent was achieved. After award of the project, the specialty grouting contractor elected to evaluate jet grouting as an alternative closure construction method. The advantages of the jet grouting option offered potential schedule and cost savings to the project as well as a superior product for seepage reduction, given the mixed soil conditions at the site. This paper presents an examination of the site conditions and project goals for the construction of the proposed closure elements for the rehabilitation of Buckeye Lake Dam. Descriptions of the original and alternative treatment methods are provided, with expected performance results. A description of the relative strengths and deficiencies of each method, as well as the feasibility and constructability of each method is provided. The implementation of the jet grouting program is presented, including a discussion of the design elements, quality control test methods, movement monitoring, and verification test methods. This paper also examines the risks associated with jet grouting and how those risks were mitigated during the grouting operations. HISTORY Buckeye Lake is situated approximately 28 miles east of Columbus, Ohio and is managed and operated by the Ohio Department of Natural Resources (ODNR) as part of the Ohio State Parks system. The lake is impounded by natural features that exist along the south and east banks of the reservoir, and by the embankment structure constructed along the north and west banks of the reservoir (see Fig. 1). The reservoir site was originally a natural swamp and the original purpose of the constructed dam and reservoir was to provide water to the Ohio and Erie Canal System. Several dam alignments and configurations were constructed during its early history; however, the original embankment is comprised of homogeneous earthen fill. The embankment is 15 ft (4.6 m) high and extends 4.1 miles (6.6 km) from the North Shore abutment along the east, continuing to the abutment at Lieb’s Island to the West. Several spillway and outlet structures exist along the embankment alignment. Most noteworthy are Seller’s Spillway and Amil Spillway. Fig. 2 is a Plan View of the embankment alignment and appurtenant structures at Buckeye Lake.

Jan 1, 2019

By Jeffrey C. Evans, Daniel G. Ruffing, Hejintao Huang

Soil-bentonite slurry trench cutoff walls are the most common type of vertical cutoff wall used in the US for seepage control and for passive control of contaminant migration at environmental sites. Design considerations are often limited to constructability considerations and a target hydraulic conductivity. With design-build contracts common, the backfill design is often left to the contractor. As a barrier soil, the hydraulic conductivity of bentonite slurry wall backfill is typically required to be equal to or below 1x10-7cm/s. The importance of stress state upon the hydraulic conductivity as well as the expected stresses are both established in the literature. Grain size distribution of the base soil and bentonite content both affect compressibility and hydraulic conductivity. This paper describes the results of studies undertaken to evaluate the interrelationships between compressibility, hydraulic conductivity, grain size distribution, and bentonite content. Three base soils were used representing a range of soils found on typical construction projects. Using these base soils, mixtures containing a range of dry bentonite contents from 0% to 5% were prepared to a slump consistent with field practice. The compressibility and hydraulic conductivity were measured in consolidometers adapted for falling head permeability tests at the end of each load increment. These experiments yielded the relationship between effective stress and hydraulic conductivity as well as consolidation characteristics including time rate of consolidation and coefficients of compressibility. The experimental results are then used to indirectly evaluate stress development and to assess the time needed for consolidation. The findings show a substantial decrease in hydraulic conductivity as effective stress increases, regardless of base soil type and dry bentonite content, a relative insensitivity of stress development to backfill compressibility, and a wide range of values for coefficient of consolidation depending upon backfill mixture and stress level.

Jan 1, 2016

By Mihir B. Roy

"Coal transported by rail for Thermal Power Plant in Haldia, West Bengal, India, was to be received and stored in Coal Complex comprising of Wagon Tippler, Track Hopper, Junction Houses and network of horizontal and inclined tunnels. The site was very soft with high ground water level. Deep excavation and dewatering posed great difficulty. Original plan was to drive about 1000 m of steel sheet pile and well sinking which had major impact on cost and time. High ground water was identified as the main problem. Controlling water level and maintaining it would allow open excavation over major areas. Scheme for lowering aquifer with one and two-stage well-point dewatering system was developed following basic principles of groundwater and seepage. Arrangements of wells, installation and pumping were worked out in detail. Water levels could be lowered below bottom levels of excavation. Design of sheet pile was modified under lowered ground water condition. Overall length and depth of sheet pile were reduced drastically. Open excavation was possible in segments over major areas. The scheme was highly successful in smooth and fast progress of underground works. The works were completed safely months ahead of schedule time and with significant saving in cost.INTRODUCTIONThe Coal Receiving Complex of thermal power plant comprised of 250 m long 8 m deep Track Hopper (TH), 12 m deep Wagon Tippler (WT) with provision for addition of another Wagon Tippler. Track center lines of TH and WT were very close. Coal unloading facilities were connected with a network of underground tunnels and Transfer Points (TP) upto Pent House (PH). The facilities were optimized in a compact layout within about 400 m x 120 m area. Initially excavation for TH was started adopting side slope of (1 V : 1.5 H) with 2 m wide berm and dewatering by in-pit sump and pump. When depth of excavation reached about 5-6 m, failure occurred over a long stretch as shown in Figs. 1a - 1b photos. Further work was stopped to develop scheme for carrying out deep excavation and civil works safely."

Jan 1, 2015

By Anthony D. Barley

Over 60,000 multiple anchors have been used internationally since their introduction in the early 1990s, including 1000 in the United States. The multiple anchor system comprises a "multiple" of "unit" anchors installed within a single borehole - each unit anchor being staggered within the borehole length to mobilize its own capacity independently of the other unit anchors. These systems offer higher capacity than conventional anchors with identical bond lengths due to superior load transfer efficiency. The use of higher capacity anchors may allow reduction in the number of anchors required on a project, which results in time and cost benefits to the anchor installer, contractor, and the owner. Fully removable temporary multiple anchors are available, and have been used with consistent success. Three case histories are discussed highlighting the use of these systems

Jan 1, 2002

By Atta B. Yiadom, A. David Miller, Robert C. Kirby, Sean M. Todaro

"San Pablo Dam is a 170-foot (52-meter)-high earthfill embankment, located approximately 10 miles (16 kilometers) north of downtown Oakland, California, that impounds a 38,600 acre-feet (47.6 million m3) reservoir for customers in the East Bay Municipal Utility District's (EBMUD's) service area. Seismic upgrades were designed and constructed in 2008 through 2010. Work included removal of an existing 140,000 cubic-yard (107,000 m3) downstream buttress, which was replaced with an enlarged 300,000 cubic-yard (230,000 m3) buttress founded on alluvium and colluvium that were improved in-place using Cement Deep Soil Mixing (CDSM) technology. The site characterization for the project, design of CDSM, reuse of CDSM spoils as construction materials, and environmental permitting have been described in five previously published professional papers.This paper provides a brief summary of the design of the seismic upgrades and presents the results of measurements made during and/or after construction including the variation of CDSM strengths with time, piezometric levels within the dam and foundation soils, and seepage flow rates. These measured values are compared to the values estimated during design of the seismic upgrades.INTRODUCTIONSan Pablo Reservoir is located approximately 10 miles (16 kilometers) north of downtown Oakland, California, as shown in Fig 1. As many as 50 million gallons (200,000 m3) per day pass through the reservoir for treatment and distribution to a portion of the 1.3 million customers served by EBMUD. The dam is founded mainly on alluvium and was originally built in 1920 using materials excavated from the left and right abutments consisting of siltstone, claystone, fine-grained sandstone, mudstone, and shale that were excavated and placed using hydraulic fill methods. The dam is located within two miles (three kilometers) of the Hayward Fault which is capable of a moment magnitude 7.25 earthquake.Because of the foundation materials, construction method, and proximity to the Hayward Fault, the dam has undergone a series of seismic improvements, including the placement of a downstream compacted earth buttress in 1967 and an upstream compacted earth buttress in 1979. In 2002, the State of California Division of Safety of Dams (DSOD) requested that EBMUD evaluate the seismic stability of San Pablo Dam, following the results of a study that same year that indicated a 62 percent chance of a greater than 6.7 magnitude earthquake striking the San Francisco Bay region between 2003 and 2032. The dam was evaluated and it was concluded that portions of the underlying foundation soils may liquefy during the maximum credible earthquake which could cause the dam to become unstable."

Jan 1, 2015

By Nils Schneider, Marc Peters, Stefan Frey, Andrea Fluck

Due to the worldwide population growth, the development of sustainable infrastructure and the exploration of renewable energies plays a key role to handle the rising megacity trends and to limit carbon footprint. Herrenknecht AG is a leading manufacturer of Tunnel Boring machines and has constantly endeavored through its extensive Research and Development programs to address limitations faced by the civil engineering industry as regards to construction equipment capabilities. New mechanized technologies, mainly coming from the tunnelling industry, have been developed by Herrenknecht AG as an efficient alternative to conventional civil engineering, where tailor-made concepts are required to comply with restricted conditions onsite. Very often this innovation led technology capability has meant making construction processes safer due to minimal human intervention and also far more productive due to higher performance as compared to other latest or conventional methods of construction. The rising need for even higher building structures and large-capacity bridges involve the development of innovative deep foundation technologies for on- and offshore operation. Conventional methods like bore piles reach their technical and economic limits under certain conditions. For building shafts and foundations, the mechanized Vertical Shaft Sinking Machine technology (VSM) from Herrenknecht AG is a proven innovation and has now been used in various onshore infrastructure projects worldwide to construct a total of 94 circular shafts in depths of up to 115 meters. It operates below the groundwater level, completely remote-controlled from the surface in a diameter range from 4.5 to 18 meters. Subsequently Herrenknecht noted that Offshore foundations, especially in non-drivable ground conditions such as soft and hard rock (e.g. limestone, sandstone, mudstone, granite etc. or soft soil with high density) and shallow continental shelf (water depth approx. 20-60m), presented construction challenges and equally an opportunity for building high performance equipment. The latter construction conditions usually requires drilled installation methods for applications such as harbor enlargements, bridge foundations and foundations for offshore wind turbines. The Offshore Foundation Drilling technology (OFD®) is Herrenknecht’s latest innovation, incorporating our learnings from the VSM and full-face Tunnel Boring machines, and the OFD® enables a rapid and economical offshore installation in such variable ground and rock conditions. This paper will discuss the technology behind the new mechanized technology of VSM and Herrenknecht’s latest innovation of the OFD® along with their respective application fields in foundations construction. The paper will further present in details, their range of benefits to the construction industry.

Nov 1, 2022

By N. V. Nayak

Maharashtra State Road Development Corporation Ltd., has initiated a scheme for construction of 55 flyovers in Mumbai in India. To ensure speedier completion of projects several new technologies were adopted to save time without compromising on safety and reliability. Many of the flyovers involved large diameter pile foundations carrying loads ranging from 3500kN to 1375kN. Significant time would have been lost in using conventional load testing procedure to check pile capacity apart from the difficulty in mobilizing the load and the obstruction to site movement and traffic on the adjoining roads. High Strain Dynamic Testing was introduced on the project sites in lieu of static load testing after conducting numerous co-relation studies on various project sites. A total of seven co-relation studies have been conducted till date and based on these data static testing has been replaced by dynamic testing on numerous flyovers. The paper presents the results of such studies. CAPWAP analysis was also conducted on the data to evaluate the percent skin friction and end bearing so as to improve future design parameters.

Jan 1, 2000

By Thomas Hyatt, Brandon Phetteplace, Camilo Alvarez

A test pile program was undertaken at a project site in Ain Sukhna, Egypt for an import/export oil jetty. Two 1219 mm diameter open ended steel pipe piles were evaluated at two separate test locations. Each test pile was dynamically tested during initial drive utilizing a Pile Driving Analyzer (PDA). Restrike testing was also performed to evaluate the time dependent soil setup. One static compression test and one static tension test was performed at each test location. A correlation of the static and dynamic load test results was established to develop a driving criteria for the piling across the two kilometer project. The constructability benefits of shorter piles will be discussed in more detail, given that the pile lengths were shortened by 9 to 10 meters on average. Lastly, the use of a four pile linear layout to perform both compression and tension tests will be covered. INTRODUCTION With the increased number of Very Large Crude Carriers (VLCC) & Ultra Large Crude Carriers (ULCC) being used to transport oil products around the world, companies and/or nations are presented with the challenge of transferring these products to and from the carriers in deep water scenarios, typically 15 to 20 meter depths, to accommodate the vessels draft. One option for loading/unloading the oil products from a VLCC or ULCC would be to transfer to/from smaller vessels several miles offshore, whereas the most economical option is to unload directly to a pipeline via a berth/jetty platform near shore. These berth platforms must be designed to withstand multiple loading scenarios while these carriers are moored and transferring their products. The use of Large Diameter Open Ended Pipes (LDOEP) piles are a common foundation choice for this offshore application. One of the drawbacks of LDOEP piles, especially across a large project site, is that there can be extreme variability in the pile driving behavior. This can be caused by either a change in soil conditions or the performance of the soil plug. Due to this variability, it is important to verify throughout the duration of the project that the piling is being installed to the correct criteria as established during the load test program. A well designed driven pile load test program, preferably with the combination of Static Load Testing (SLT) and Pile Driving Analysis (PDA), should develop a driving criteria that can allow the contractor and owner to monitor any change in driving behavior.

Jan 1, 2019

By W. Sondermann

"AbstractThe construction of a distribution centre of minerals for a global mining and resources cooperation demanded the control of deformations and displacement of the stack reclaimer facilities on very inhomogeneous subsoil conditions. The variation of quality from soft clay with CPT values below 1 MPa up to rock formations were the challenge in design and execution of all the foundation works.The advanced design considerations were resulting in a barrier wall system to limit the deformations of the up to 40 m deep bored pile of the stacker-reclaimers, whereas the layout of the barrier wall and the stiffness of the elements had a major impact on the residual lateral forces to be absorbed by the bearing structure.IntroductionA large international raw material distribution organisation is currently building an iron ore and pellet distribution centre on the north-western coast of Malaysia. The distribution centre will handle around 90 MTPA (million tons per annum) of iron ore and includes accompanying plants for loading and unloading iron ore and pellets, pelletizing plants as well as corresponding storage space for these raw materials. The total storage space extends about 800m north to south respectively 1400m east to west and is about 200m from the coastline. The project area is located in a wide valley basin, bounded by a range of hills to the north. The existence of soil with low bearing capability in the area designated for the plant meant that measurements for ground improvement were required in the storage areas, in order to combine the needs of iron ore and pellet storage areas with requirements of the loading facilities as the overall project demand.Project LayoutThe iron ore distribution centre and the pelletizing facility both consist of an import/export jetty, material handling facilities, pellet plant and the associated infrastructure. This publication describes the execution of ground improvement and foundation works for the loading and storage system, which consists of five rows of stockpiles and four intermediate rows of stacker-reclaimers. The total area of these systems comprises 278,881 m2 (Fig. 1)."

Jan 1, 2014

By Bosco Poon, Kim Chan, Luis Raúl Castañeda, Geoff McKay

"Driven steel tubular piles of up to 2 m diameter have been used to support abutments and piers of a bridge over Nambucca River and floodplain. The bridge was designed by Arup-Aurecon Design Joint Venture (Lead Designers) with GHD leading the geotechnical design assessment in conjunction with Acciona Ferrovial Joint Venture (AFJV – Principal Contractor). Piles were to be driven through alluvium and founded on foliated Phyllite bedrock. The large diameter piles posed significant challenges on bearing capacity assessment and pile acceptance criteria, especially for anisotropic rock strength. Prior to pile driving, boreholes were drilled at each pile location, accompanied with a suite of rock index and UCS testing. AFJV and GHD oversaw geotechnical construction verification. All production piles were monitored with a Pile-Driving-Analyser to manage driving stresses and pile termination. Wave matching CAPWAP analyses were performed on 40% of the piles at the end-ofdrive, or restrike, to satisfy specification requirements and limit over-driving. This paper presents discussions on the design and construction of the driven piles with findings from the extensive dynamic pile data obtained. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft frictions fs of the soil / rock materials, as well as the end bearing fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the m obilised fb, and the relationship between rock strength and the mobilised fs are outlined.INTRODUCTIONThe Bridge over Nambucca River consists of a single bridge structure, comprising single substructures and separate superstructures. The 850 m long bridge facilitates the crossing of the Northbound and Southbound carriageways of the Pacific Highway Upgrade over Nambucca River, with central median barriers, separated by a horizontal clearance of 50 mm. The bridge is required to span over the Nambucca River, which is a navigational channel, and over the adjacent floodplains, including two local access roads and the existing Pacific Highway. The bridge superstructure consists of 21 simply supported spans, each comprises four 2.25 m deep precast post-tensioned U-Girders, with two girders across the width of each carriageway. The spans of girders vary from eleven spans of 39.5m and ten spans of 41.5 m. The floodplain section of the bridge was founded on up to 2m diameter steel tubular piles, designed to be driven through alluvial sediments and weak rock to nominal refusal on sound rock. Dynamic load testing using wave matching CAPWAP (CAse Pile Wave Analysis Program) analyses in conjunction with PDA (Pile Driving Analyser) were used to verify the pile integrity and mobilised capacity. This paper discusses geotechnical aspects associated with design and construction of driven piles. The methodology developed for construction to verify pile capacity and to meet acceptance criteria is outlined. Based on the shaft resistance distribution and toe resistance obtained from CAPWAP analysis, the mobilised pile shaft friction, fs of the soil / rock materials, as well as the end bearing, fb of the founding Phyllite bedrock, are examined. The impact of the rock fabric foliation angle on the mobilised fb, and the relationship between rock strength and the mobilised fs are outlined."

Jan 1, 1900

By Challa Venkata Rami Reddy, Anindya Roy, G. R. Konni

This paper presents the results of pile lateral capacities obtained from both conventional design and fullscale pile lateral load tests. Conventional design using P-Y curve analysis is very commonly being used by designers; designers use well accepted software programs like Lpile and Allpile for analysis. However, these programs do not cover the soil models to simulate engineering behavior of marine carbonate sands; which generally have different engineering behavior than silica/quarts sands. In this study, the existing soil models for common sands have been used to assess pile lateral capacities and these results are compared with the results from full-scale instrumented pile lateral load tests performed in compacted marine carbonate sand fills of artificial island constructed for oil and gas facilities in Abu Dhabi. The objective of this study was to verify the applicability of the existing sand soil models for carbonate sands and also to verify the associated conservatism in the pile lateral capacities. This study shows that the actual pile lateral response is much stiffer than what was anticipated through the LPile analysis. Therefore, further research focus may be required to capture the engineering behavior of the marine carbonate sands to develop specific P-Y curves.

Sep 8, 2021

By John C. Ryan

The Emeca Pile Splice, an innovative mechanical prestressed concrete pile splice, is the first robotically welded splice to be fabricated in the United States. An analytical and experimental study was conducted to establish the capacity of the standard splice for 12-in. and 14-in. square piles. The study illustrates compliance of the splice with International Building Code (2006) requirements. A case study for a large petroleum tank foundation project in Port Canaveral, FL is presented, demonstrating the efficiency achieved through use of spliced-piles. For the case-study project, single-piece 18-in.-square, 100-ft-long piles were replaced with 12-in.-square, two-piece, spliced piles. As a result, a significant reduction of material, labor, handling, and equipment was documented for the project. Savings realized on the installed pile cost was estimated to be in excess of 30% by the owner.

Jan 1, 2010

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Attasit Korchaiyapruk, Edward C. Clukey

"A deep mixing method (DMM) foundation was selected by the Project Team for a very large LNG facility in West Africa. As described in a companion paper, this foundation consists of a large number of columns installed by mixing cement with in-situ soils. The foundations are arrayed as a variety of honeycombed type configurations which, if installed to desired specifications, can provide a robust foundation alternative. The foundation is capable of distributing loads and limiting settlements even if some of the soil in the columns is not fully mixed during installation. An important part of the overall quality assessment program, therefore, involved developing a testing program to verify the methodology. In addition the impact of potential defects in columns on the overall foundation integrity had to be assessed. This paper describes some of the preliminary work done to establish the requirements for the quality assurance program. A key component of this program involved the sampling frequency used to assess potential defects in the columns. To verify the column integrity 104- mm samples were taken continuously at a selected frequency through the 23 m long columns. The preliminary work described in this paper demonstrated that the appropriate sampling frequency depends on both the desired reliability level as well as the number of defective columns encountered during testing.Initial finite element analyses were performed to assess the extent that defects could occur in columns within the honeycombed structure without adversely affecting the overall foundation integrity. The results from this work demonstrated that the spatial location of the defects was critical to properly assessing the foundation integrity.In addition to column sampling a load test was performed as part of the foundation verification process. The methods used to apply appropriate loads so that loads at the bottom of the columns approached design values are discussed in the paper.The results obtained from this preliminary study were then used to help develop a more comprehensive assessment program, described in a companion paper, to determine the robustness of the DMM foundations for both the LNG processing facilities and a condensate tank.IntroductionFoundations constructed with the Deep Mixing Method (DMM) can be an attractive and cost efficient alternate to other deep foundation options. This foundation is constructed by mixing soil and cement with an auger type drill. The foundation is usually constructed with a dual auger system that simultaneously creates two contiguous columns called foundation elements. Many elements are then arranged in a honeycombed configuration to create the overall foundation (Figure 1). A desired column strength can be obtained by varying the volume of cement added to the columns, the mixing rate of the soil and stroking sequence."

Jan 1, 2017

By Ryan C. Linthicum

A system of steel sheeting and multiple levels of high capacity double corrosion protected soil anchors were used to restrain a major slope failure that occurred at the base of the Watchung Mountains mid-way through construction of a 650,000 SF retail center along Route 22 in Watchung, New Jersey. The implementation of a design-build earth retaining structure was necessary to stabilize and repair the disturbed mountainside in a timely fashion to permit completion of the retail center on a fast track schedule. The tied back steel sheetpile wall was approximately 2,000 feet long and varied in height from 12 to 25 feet. The hillside extended approximately 350 feet above and 600 feet beyond the wall with the main failure scarp extending 50 feet above and 90 feet beyond. The wall was constructed in a top-down manner and required the installation of 475 anchors to resist loads of up to 70 kips/ft produced by the creeping hillside and groundwater flows from both a series of springs and steady state seepage through an inclined zone of fine sand. Incorporation of a unique tie point connection eliminated the need for a waler, facilitating and simplifying modifications to anchor locations based on anchor load test results and conditions encountered during construction. Post grouting also proved to be an essential element in the successful construction. This paper presents the design and the construction methods used to restrain the significant earth lateral loads produced by a slope failure using steel sheeting tied back with high capacity soil anchors with anchor loads distributed to the sheeting through a unique tie point connection on a fast track schedule. Installation techniques, testing programs, and construction quality control are also discussed.

Jan 1, 2003

By Fred Tarquinio, Giovanni Bonita, Lars Wagner

"A new embassy for the Peoples Republic of China is under construction in Washington, DC. The 475,000 square feet (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. A vertical soil nail wall was used as the primary support of excavation system for the project. The soil nail wall was irregularly shaped, benched in areas, and up to 98 feet (29.9 m) in height. The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Design and construction challenges included soft soil conditions, inside wall corners, underground utilities, seismic impacts from blasting, and logistical and political factors. Overall, wall movements were lower than expected, with maximum horizontal movement less than 0.25% of the total height of the excavation.INTRODUCTIONThe proposed Embassy of the Peoples Republic of China in Washington, DC, will consist of about 475,000 ft2 (44,125 m2) of building space and contain up to four fl oor levels above ground and fi ve levels of basement (Figure 1). When completed, the building will be the largest embassy in Washington, DC. The architect for the project, Pei Partnership Architects, along with the world-renowned architect I.M. Pei, made effi cient use of the site by inserting the building into the existing slope. Consequently, excavations reach heights up to 98 feet (29.9 m) on the southern side of the property and 42 feet (12.8 m) on the northern side.The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. The location of the building relative to the property line called for tight excavation requirements, including precise wall positions and shotcrete tolerances. Design and construction challenges included soft soil conditions, inside wall corners, arched walls, underground utilities, seismic impacts from blasting, and logistical and political factors.SITE INVESTIGATIONInformation obtained from the geotechnical investigation revealed about 10 to 20 feet (3.1 to 6.1 m) of a loose to medium dense fi ll material placed during previous site activities. The fi ll material was underlain by a silty sand and sandy silt residual soil derived from the natural weathering of the underlying bedrock. This soil sequenced naturally from a medium dense to very dense material through natural weathering of the underlying bedrock. This soil sequenced naturally from a medium dense to very dense material through natural weathering processes in the rock. The underlying bedrock was locally characterized as a gneiss. A water table elevation about 17 feet (5.2 m) above the fi nal excavation level was revealed, except in the “radius” area, where a leaking water main/hydrant generated a high local water table."

Jan 1, 2007

By Mohamed Mekkawy, William W. Wheaton, Ira Brotman

"The Virginia Port Authority and the U.S. Army Corps of Engineers are partnering to construct the Craney Island Eastward Expansion (CIEE) to meet the dual purpose of extending the life of Craney Island as a dredged material management area and providing land for a state-of-the-art marine terminal. The over 500-acre (200-hectare) expansion provides additional upland dredged material capacity for the Hampton Roads Harbor by constructing perimeter dikes, that once filled, will provide land for the development of a container terminal. In the winter of 2010/2011 the first stage of sand fill was placed, followed by the installation of approximately 12 million linear feet (MLF) (3.6 million linear meters, MLM) of marine PVDs. With over 36 MLF (10.9 MLM) of PVD required to complete dike construction the project will be one of the largest PVD installation project in the U.S.This paper details the challenges associated with the construction of the cross dikes, in particular the design, testing, installation and monitoring of prefabricated vertical drains (PVDs) installed overwater to depths of over 130 feet (40 meters) for foundation improvement in the insitu very soft Norfolk Clay. With expected settlements of 20–30 ft (7-10 m) and 30 percent average strains, the discharge capacity of the PVDs was of particular concern. Laboratory data is presented showing the magnitudes and variability of discharge capacity under different confining pressures in both a straight and buckled condition.The method of installation and monitoring of the marine PVDs in open water included developing a specialized barge and sophisticated positioning and data collection system to verify installation location, depth of penetration and track quantities. An observational method, including material testing, detailed surveys, periodic in-situ testing, and instrumentation, was utilized by the project team to assess the project’s progress and allow for validation of consolidation and strength gain rates and magnitudes."

Jan 1, 2017

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018