Search Documents

By Kazimierz Gwizdala

In the paper the method for estimation of settlement of vertically loaded piles in a group is presented. The method is generally based on the hybrid procedure with non-linear solution for single piles and with interaction between them for the low-strain shear modulus. Some attention is paid to the influence of deformation and strength parameters used in calculations. The applied model is verified in the framework of the research programme carried out recently in the Geotechnical Department of Gdansk Technical University. It concerns monitoring and analysing the settlements of the existing structures on piles. A comparison of calculation and measurements results for two tested buildings is presented as an example.

Jan 1, 2002

By Susheel R. Kolwalkar

A significant increase in the side shear capacity over a period of time is often observed in case of driven piles. This phenomenon is referred to as ?setup? or ?freeze?. This phenomenon cannot be predicted based on the knowledge of the engineering properties of soil. Different kinds of mechanisms have been proposed in order to explain set-up in cohesive soils. In engineering practice, set-up is incorporated in design on the basis of empirical formulae and depends to a large extent on personal experience and judgment of the design engineer. Set-up is a natural process which cannot be accelerated by any existing practice. A research was initiated to investigate the mechanism of pile set-up in clayey soils and explore the possibility of accelerating the set-up process by an electro-kinetic method. The system chosen for the present study consists of a prototype steel pile driven in kaolinite clay. A laboratory test program was developed at Cleveland State University in order to meet the goals of the proposed research. Results obtained from these tests are very encouraging and show pile capacity increase of 200% within the first 5 days of electric gradient application versus those that experience natural set-up. In this paper, theoretical considerations and laboratory test results are presented and discussed.

Jan 1, 2008

By T. Soejima

In recent years, there has been a tendency in the field of foundation piling works to utilize piles of greater bearing capacity in order to meet increasing height and weight of modern building as a means of saving of piling cost. To satisfy these requirement, a new technique for large diameter bell bottom cast-in-place piling has been developed utilizing multi-head reverse circulation drilling system.

Jan 1, 2010

By Jon H. Gould

This paper describes the following at the new Advanced Solid Rocket Motor (ASRM) nozzle manufacturing facility, which is being constructed inside an existing manufacturing facility: 1) generalized subsurface conditions, 2) pile load test program and evaluation, 3) pile selection, 4) problems associated with pile driving operations, and 5) production pile installation. The poor subsurface conditions, known and unknown underground obstructions, and work environment inside the existing building, used to manufacture the Space Shuttle external fuel tanks, required special pile installation equipment, procedures, and work schedules to install the economical pile foundation system ahead of schedule and without a lost time accident. GEOTECHNICAL STUDIES In April and May 1990, 16 soil test borings were drilled inside the existing building with a truck-mounted drill rig. The borings extended to depths ranging from 60 to 65 ft (18.3 to 19.8 m) below the floor slab. Typically, the silty and clayey soils were sampled by pushing "undisturbed" Shelby tubes, and the more sandy soils were sampled by driving a Standard Penetration Test (SPT) split-spoon sampler. The unconfined compressive strength, water content, and unit weight of the Shelby tube samples were measured in the laboratory. A geotechnical report was issued in May 1990 presenting the results of the field and laboratory testing and foundation recommendations (Gilbert, 1990).

Jan 1, 1992

By Eric S. White, Thomas J. Sabourin, Khuram R. Mohib

"This paper presents the challenges associated with the design and construction of a steel sheet pile cofferdam supported with one level of grouted anchors in clean to silty sand with gravel. The initial assessment of the subsurface conditions indicated loose to medium dense soil with intermittent dense to very dense layers with no occurrence of cobbles and boulders. Sheet piles were proposed to be installed to a depth of 24 m below the ground surface to limit dewatering requirements for the cofferdam. During sheet pile installation, refusal of piles occurred at multiple locations forming passages for increased flow into the cofferdam. Modifications were made in the design of the dewatering system as a result of the increased flow. Finite element modeling was used to select the necessary modifications to the dewatering system within the cofferdam. Wells were installed based on the findings of the numerical model. Model simulations showed good comparison with monitoring of the field installed dewatering system.INTRODUCTIONIt is necessary to consider the impact of the ground water, subsurface stratigraphy, strength, and drainage behavior of the soil for the design and construction of cofferdams. This paper presents a case history of the construction of a cofferdam in Northern Ontario, Canada. The project consists of the construction of a powerhouse, intake, and tailrace which will generate around 28 MW of renewable clean energy by diverting water from New Post Creek through a power house and discharge into the Abitibi River. The focus of this paper is the dewatering and excavation support required to permit construction of the powerhouse. The layout of the cofferdam is shown in Fig. 1. The cofferdam for the powerhouse is rectangular in shape with sheet piles on all four sides intended to be driven to the design toe El. 101 m. The east and west walls have a length of 46.3 m. North and south sides are 47.6 m long; and in addition, two cantilever sheet pile walls bound the tailrace on the west side and two cantilever walls were installed on the east for construction of the penstock inlet. The ground surface in the powerhouse cofferdam area, before commencement of sheet pile driving, was brought to El. 125; the ground then slopes up to the East, toward New Post Creek, and the site is bounded on the West by the Abitibi River. 186 pairs of sheet piles were used to create the cofferdam and cantilever walls. The deepest excavation is to elevation 114.4 m. Within the west half of the cofferdam footprint, the base of excavation slopes upward at 3H: 1V to facilitate the tailrace discharge into Abitibi River.SOIL STRATIGRAPHYThe cofferdam design was based on the geotechnical investigation conducted by AECOM (2014) which included two relevant boreholes near the powerhouse footprint. The ground elevation at the time of investigation varied between 131 to 129 m. The material observed to the full depth of investigation was comprised generally of coarse to fine sand and gravelly sand or a sand matrix with gravelly inclusions. Some intermittent layers of clay and silt intrusions were also observed. Generally the soils grade finer away from the river. SPT N60 values were recorded in two borings during the field investigation with values reported from 3 to 92. The in-situ conditions ranged from compact to dense with some loose and some very dense zones. Figure 2 shows the variation in SPT N60 values with elevation."

Jan 1, 2017

By J. X. Wu

An investigation on the seismic damage to buildings with pile foundations in Tianjin region, was conducted after the earthquake which hit Tangshan in 1976. It showed that most pile-founded buildings have an excellent aseismic capacity. In this paper, several pile-founded projects suffering the seismic damage are introduced as examples, simplified calculations are made of the vertical bearing capacity of pile foundations and of the horizontal seismic force, and suggestions are presented in conection with the design of pile foundations in the liquified ground soil. The paper shows a frame structure which has a plie foundation with a box-shaped base. Analyses if its response to the earthquake has been carried out in accordance with the F.E.M. and results have been obtained.

Jan 1, 2010

By Brian P. Waagner

Construction law in general and the law of deep foundations in particular continues to develop rapidly, particularly in the areas of risk allocation. Public and private owners are increasingly using contractual disclaimers to shift the risk of differing site conditions to contractors, and courts are increasingly willing to enforce these contractual devices. Perhaps also in an effort to control costs, public and private owners are turning to design-build contracting techniques. While design-build offers many advantages over traditional project delivery systems, it does not answer all of the risk-allocation questions that frequently arise. Even in design-build, problems with unanticipated subsurface conditions and defective design are not easily addressed. Finally, developments in electronic commerce present the potential to transform the construction industry.

Jan 1, 2002

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2000

By A. F. Deng

A general description of the project, mainly the pier foundation design of the ZHU JIANG FANYING is presented in the paper. The major contents include the foundation scheme, the evaluation of bed-rock characteristics, the allowable bearing pressure, the design and construction of pier foundation.

Jan 1, 2010

By David Winter

The geotechnical design, construction, and monitoring aspects of a tied back excavation 85 feet deep in Seattle, Washington are presented. The excavation was completed in overconsolidated deposits of sand, silt, and clay. Lateral soil pressures used in shoring wall design were the lowest to date for an excavation of this size in Seattle. Instrumentation data collected from hydraulic load cells and inclinometers were analyzed and are discussed. The data suggest the actual soil pressures felt by the wall were lower than the design values. Recommendations for future study, as well as future design modifications are given.

Jan 1, 1987

By George K. Burke

Underpinning of a structure has been traditionally expensive, time consuming, and, in many cases, caused as much settlement to the existing structure as it was trying to prevent. As underpinning is normally one of the initial tasks and on the critical path on a construction project, there is immense pressure on the subcontractor to speed up his operation so the new structure can proceed; this can cause an adversarial relationship to develop between the owner, engineers, general contractor and subcontractor. Since its introduction to the North American market in the late 1980's, Jet Grouting has not solved all these problems, but where utilized, has shown economical benefits, a faster and safer installation, and a minimal movement of the structures being underpinned. A history of the development of jet grouting is presented; a comparison of this technique versus other grouting methods, a description of the jet grouting system with emphasis on the triple rod systems; case histories of jet grouting used for underpinning and conclusions and references are included to follow the program's themes of: - Recognizing Solutions to Today's Problems - Defining Tomorrows Challenges - Putting America on a Solid Foundation

Jan 1, 1991

By Robert C. Rabeler

Soil and Materials Engineers, Inc. (SME) has utilized drilled cast-in-place (D-CIP) piles on a number of projects in the midwest. These foundation systems have typically consisted of drilling an 8 to 9-inch diameter borehole with a rotary type drill rig or driving a casing with a small hammer. A structural steel member is installed in the center of the excavated space, and the borehole or casing is grouted to complete the installation of the D-CIP pile. This type of piling system has also been called: mini-pile, micro-pile, or drilled-in pier. The capacity of these piles varies depending upon subsurface conditions, as well as the structural capacity of the pile. The structural capacity can be modified based on the size and yield strength of the structural steel member. SME has used the D-CIP piles for underpinning of lightly-loaded structures for a number of years. Steel brackets can be welded to the structural steel member in the center of these piles, and the bracket extended underneath existing foundations to provide proper foundation support. D-CIP piles have also been used for new construction where access was limited. Recently, SME had the opportunity of providing design as well as construction monitoring services for a unique project where these piles were used, but at much higher capacity. The project involved adding seven additional floors on top of a five-story building (total of 12 stories). New columns were extended through the existing building to support the new floors. Access to construct foundations was available to one level of underground parking beneath the structure, as well as to a basement area. Access required equipment to travel through a 3-foot wide hallway. A special duplex drilling machine was used to access the foundation locations and to install the piles in a limited headroom condition. Eight-inch diameter D-CIP piles were extended to a depth of approximately 40 to 50 feet below grade and socketed into a dense clay till or sandstone, and No. 18 or No. 20 threaded bars were installed in the center of these piles. The design pile capacity was as high as 190 kips and were verified by a compression load test. The load test was performed with limited access and headroom. These piles were installed by Spencer White and Prentis Foundation Corporation (SWP). For conditions where rock or hard soils are encountered at reasonable depths, D-CIP piles can provide working load capacities comparable to larger driven steel piles. The ability of the equipment to access very restricted areas, combined with the high capacities results in a very attractive solution to a number of difficult foundation problems.

Jan 1, 1999

By Richard D. Short

The Pseudo Static Pile Load Test, PLT, is a rapid method for determining pile capacity. Pile design is usually based on theoretical calculations of ultimate load capacity using soil data from a field investigation. The pile capacity is confirmed during construction by analysis of blow counts using dynamic formulae, dynamic pile monitoring, and load testing. Load testing is the most direct and reliable method of determining the actual capacity of a pile. Conventional load testing procedures, however, are time consuming and expensive. A typical load test requires installation of two to four reaction piles, construction of a high-capacity steel test frame, hydraulic jacks, and dial gauges, and will typically take one to three days per pile. Costs for load tests range from $10,000 to $20,000 per test. The Pile Load Test machine features a 25-tonne weight mounted on a mobile test frame. PLT load tests can be performed in a matter of minutes once the equipment has been mobilized to the site. This paper examines three test sites where the PLT test method was used and compares the results to conventional load test results and theoretical capacity calculations.

Jan 1, 2000

By Mark A. Willian

The purpose of this short paper is to present soil profiles and basic soils information for the portion of the I-880 Replacement Project alignment where highway structures are to be built. The information presented here is derived primarily from foundation investigations conducted by the Caltrans Foundation Unit (currently the Structures Foundation Branch, Office of Structural Foundations) and by others under Caltrans direction. The foundation investigation for the I-880 Replacement Project began in May of 1991. The field work was completed in May of 1992 and consisted of 93 rotary sample borings, 11 consolidation sample borings, 6 TEXAM® pressure meter borings, six in-place vane shear borings and 57 electronic cone penetrometer soundings.

Jan 1, 1996

By A. Frits van Tol, Rodriaan Spruit, Jan H. van Dalen

"Abstract In recent years, there have been major problems with deep excavations in urban areas supported by diaphragm walls. In some cases, like the fatal Nicoll Highway collapse in Singapore the quality of the D-walls was not the cause. However in other projects, like the problems with the major leak in the walls of the Boston Big Dig and with leakage in a few projects in Belgium and The Netherlands was related to poor D-wall quality. Leakage through the D-walls at the joints in deep excavations led in these cases to very serious settlement behind the walls, in the case of the North- South line in Amsterdam, there was severe damage to historical buildings. This paper describes ongoing research that focusses i on acquiring more knowledge on and improvement of D-wall installation, in particular the flow process prior and during casting ii on the detection of anomalies prior to excavation and iii on the composition of the concrete mixture in view of a better and more sustainable concrete quality of D-walls.INTRODUCTIONIn the case of deep excavations in urban areas close to neighbouring buildings, diaphragm walls are one of the best feasible solutions for the retaining structure. Although the costs of D-walls generally exceed the costs of alternative wall solutions, the advantages are decisive in many situations. The main advantages of D-walls are the limited impact of the installation on the built environment, the high stiffness and bearing capacity and the retention of water, even at considerable depths. This makes Dwalls often the preferred solution for deep excavations Sometimes the D-walls are the temporary support while for the final stage a complete concrete box is constructed in the excavation. In many other cases the D-wall has the permanent function of retaining soil as well as groundwater.In the last ten years, there have been major problems with deep excavations in urban areas supported by diaphragm walls. In some cases, like the fatal Nicoll Highway collapse, 2004 , the quality of the Dwalls was not the cause. In other important failures like the collapse of the Archives in Cologne, 2008 and Dubai Infinity Tower Flooding, 2007 a combination of design and quality issues played a role. However, the major leak in the walls of the Boston Big Dig was related to poor D-wall quality (McNichol, 2000). Van Tol et al, (2010) describe a number of case studies in Belgium and the Netherlands, with leakage through the D-walls at stop end joints. In several cases with deep excavations these leakage caused serious surface settlements behind the walls. In the case of the North-South line in Amsterdam, there was severe damage to historical buildings. All these cases have generated considerable additional costs and delays, and subsequently public and political concern. Van Tol et al. (2010) present several possibilities to improve the quality of D-walls.Other disputes related to D-walls deal with the quality of the concrete and the sustainability of D-walls applied as a permanent wall. In particular the porosity of the concrete cover is sometimes problematic."

Jan 1, 2014

By William S. Gardner

It is certainly an honor to have been invited to address the Deep Foundation's Annual Meeting on such a vast and weighty topic as "Present to Future Design Considerations of Deep Foundations." Acknowledging the enormity of this 30-minute assignment, I hope to at least scratch the surface of the topic deep enough to generate some thought and reflection. Design considerations, be they current or future, bring to mind a number of important subtopics which comprise the design process. As shown by Figure 1, a flow chart of this process describes, in general terms, the sequence of a deep foundation design.

Jan 1, 1991

By Andy Schroeder

Located in Hamilton, Ontario Canada, Berminghammer Foundation Equipment, is a manufacturer of advanced foundation equipment with 30 years of experience. The company is represented in more than 20 countries world wide, maintains an extensive Research and Development team, and has earned a reputation for finding the most practical solutions to the most challenging projects. The vertical travel lead, referred to as "VTL" system, was first developed and patented by C.W. Bermingham in the 1970's. This lead system was developed in response to the fundamental limitations of either a fixed lead or hanging lead system. The fixed lead system is well suited to level job sites with few obstructions and has the advantage of faster positioning of the lead, the hanging lead is very adaptable to different elevations and batter piles but takes much longer to position. Therefore the Vertical Travel Lead was developed to combine the advantages of fixed leads, fast and accurate positioning, with the ability to adjust the height of the lead base up or down. The VTL lead is connected to the boom by a sliding connection which allows the lead to be elevated or lowered below grade. The advantages of the VTL system were recognized by many foundation specialists and they have become the Industry standard in Canada , US Railway Construction , and many parts of the USA.

Jan 1, 1997

By Abdul Aziz Hanifah

A novel instrumentation and analysis technique, called GLOSTREXT method has recently been introduced for bored pile load tests in Malaysia. This technique provides an innovative and improved alternative for conventional bored pile instrumentation methods commonly practiced for the past few decades. Results for five case histories involving full scale static load tests for high capacity bored piles with both new and conventional instrumentation details placed in within the same instrumented piles are presented to demonstrate the advantages of this novel technique. Results show good agreement between the new and conventional instrumentation.

Jan 1, 2006

By Garth Howlett

In 1998 the Matanuska-Susitna Borough formed the new port district at Point MacKenzie, known as Port MacKenzie, located directly across the Knik Arm from Anchorage. In 1991 PND Engineers Inc. (PND), working with the Matanuska-Susitna Borough manager and port director, envisioned a fill structure at Port MacKenzie with a 500-foot-long Open Cell? sheet-pile bulkhead face extending to EL -20 feet Mean Lower Low Water (MLLW) at the face. Now under operation the fill created 5.5 acres of tideland property using local materials for fill. The fill is protected from 2- to-3 foot-thick ice pans and 9 feet per second (fps) tidal currents by an envelope of armor rock. Construction required working in water with 30 to 40 feet of tidal variation. Construction required placement of frozen fill in water depths possibly exceeding 50 feet, creating real concerns about soil consolidation and long-term maintenance issues. A plan was prepared to consolidate the soils using Vibracompaction. Soil Density and consolidation were monitored during the work. In 2003 the port district and NPI, a wood chip export company, formalized an agreement to construct a deep water port facility at Port MacKenzie for cape-class bulk carriers. PND provided planning, studies, geotechnical investigation, design documents and construction inspection for a 500-foot-long trestle with a platform dockhead and dolphins providing 1,100 feet of dock face in EL -70 MLLW as shown in Figure 1. Design included installation of large-diameter spin-fin piles driven on a 2V:1H batter. Also included was a 300-ton tension test of smaller spin-fin piles.

Jan 1, 2006

By Kouichi Tomisawa

Two bridges were constructed for extension work of Central Hokkaido Connection Road in 2005 at two different sites. Pile group foundations were employed for the foundations of abutments of the two bridges. In order to assess the performance of the constructed piles in the sites and to obtain design parameters for design in future, static alternating cyclic horizontal load test was carried out on one of the open-ended steel pipe piles constructed at each site. The ground at one site was characterised as a thick deposit of volcanic soils, and the ground at the other site was characterised as a very soft peat layer near the surface. In this paper the results of static alternating cyclic horizontal load tests on the piles at the two sites are presented and discussed in detail.

Jan 1, 2006