Search Documents

By Karl Ingmarsson

A model for drilling productivity and total drilling cost is presented. It specifically addresses down-thehole drilling, but also covers other drilling methods. The important factors are: 1, productivity in tons drilled; and 2, total cost per drill ton. For non-blasthole applications these factors are measured in drill feet and cost per foot. The model focuses on the entire system and allows the operator to optimize the system based on individual drilling conditions.

Jan 1, 1998

By Dr. Kyle Perry, Ryan Sibley

Rock blasting is an inherently difficult field to quantify independent & dependent variables and the specifics of how the energy interacts with the material for a number of reasons. Independent variables such as geology are innumerable and stochastic, thus, on a laboratory and full-scale basis these variables are assumed to be homogenous across the desired rock boundary. Dependent variables are difficult to quantify in the laboratory based on the specific aspect of the fracture mechanisms that caused the fracturing. The same variables are difficult to quantify in the field because of the shear amount of material being blasted. The energy interactions with the material are difficult to quantify due to the rate of the reaction and the lack of quantification of independent variables. The second main issue with laboratory scaled rock blasting is the nature of the small form-factor explosives required for use in a scaled setting. These explosives that are utilized, traditionally PETN detonating cord, have a greater ratio of potential energy converted to shock energy rather than gas energy when compared to traditional field explosives, such as emulsion or ANFO. Research over the past decades has indicated that gas pressure has the greatest contribution to rock blasting performance, such as fragmentation and material throw. The factor of varying ratios of energy production has not been discussed in any of the reviewed publications. Publications discuss dimensionless scaling, dynamic similitude, and length-based scaling, however, none of these scaling methods discuss the ratio of energy production. The main focus will be correlation of energy production ratio of shock versus gas to dependent variables. This paper analyzes previous publications within rock blasting and related field as they pertain to scaling procedures and will highlight the similarities and differences in the various publications and detail the observed omitted variables that possibly lead to skewed data.

Jan 21, 2025

By Roger L. McCarthy, Ali Reza

The use of an ammonium nitrate-fuel oil (ANFO) explosive in the Oklahoma City Federal Building bombing has led to a renewed interest in using additives during the manufacturing process of ammonium nitrate to render it non-detonable. Suggested additives include calcium carbonate, which is already used in some European countries, and mono-ammonium phosphate (MAP) or di-ammonium phosphate (DAP), which are the primary desensitizing agents claimed in US patent 3,366,468, Method for desensitizing fertilizer grade ammonium nitrate and the product obtained, issued Jan. 30, 1968 (Porter, 1965).

Jan 1, 1999

By D P. Proudfoot, S G. Keith, D P. Onagi

A number of aspects of the Canadian concept for nuclear fuel waste disposal are being assessed by Atomic Energy of Canada Limited (AECL) in a series of experiments at its Underground Research Laboratory (URL) near Lac du Bonnet, Manitoba, Canada. One of the major objectives of the work being carried out at the URL is to develop and evaluate the methods and technology to ensure safe, permanent disposal of Canada's nuclear fuel waste.

Jan 1, 1996

By Gordon F. Revey

In construction and mining work, situations occasionally occur where hard rock or concrete must be excavated at locations near critical structures or utilities. Fearing damage from blasting, contractors and engineers often explore the viability of using mechanical methods or expansive concrete to facilitate the excavation work. However, for moderate to large excavations, the prolonged duration and high cost of using these methods is often impractical. In these situations, under the right conditions, controlled blasting and blast-management methods can be used to speed up the work and lessen costs. The process of determining whether or not blasting is practical is often complex, particularly when risks are high.

Jan 1, 2002

By Jianping Li, Ernesto Villaescusa, Kelly Fleetwood

During blasting, stress waves propagate through a rock mass, inducing stress and strain changes. This applied deformation affects intact rock, existing discontinuities, mine excavations, and engineered structures in the proximity of the blast. Traditionally in blasting, stress waves are quantified in terms of peak particle velocity (PPV) or peak particle acceleration (PPA), based on the method of measurement and the specified allowable tolerances. During analysis, the peak particle motion is coupled with an explosive source through various scaling laws to develop rock-specific attenuation relationships. Some studies have expanded this practice to the development of damage threshold values based on measured or predicted peak particle velocities. PPV-related thresholds are generally based on empirical models, where observation of overbreak, cracking, or fall-off are used to quantify damage. This method is often paired with the application of elastic plane wave equations to calculate the blast induced strain or the PPV threshold for tensile rock failure. Other factors that must be viewed critically in such models are the methods used to collect and analyse blast vibration data and the application of inappropriate vibration attenuation relationships.

Jan 1, 2009

By Richard N. Snyder

In this system for connecting blasting caps to the initiation source, the need for a redundant design structure provides more reliable method of explosive initiation. This is accomplished by using a complete system starting at the blasting control, through the initiation line structure through the initiation line and connecting blocks to the blasting cap. The connecting structure between the initiation device and the blasting caps may be connecting blocks or other means.

Jan 1, 1995

By Willard Pierce

Very few people will consciously decide to do an unsafe act. With that said, how many of us unconsciously put ourselves in harms way, sometimes even on a daily basis? Complacency on the job may have very little to do with not caring or a poor attitude. It may be just as simple as failing to continue to recognize the hazards surrounding us throughout the day. At the very worst, it is both.

Jan 1, 2006

By Huang Fenglei, Jin Qiankun

A new linear charge method has been applied in coyote blasting for highway excavation in which presplitting boreholes are set along the designed rock slope with some empty chambers at the end of linear charges whose axes are perpendicular to the axis of the highway. Three-dimensional nonlinear finite element analysis for this method has been conducted using LS-DYNA3D. The results indicate that the blasting damage to the rock slope is reduced greatly using the new linear charge method in coyote blasting.

Jan 1, 1998

By Joseph Hoang, Nick Reed, Scott Wishart, Michael Lovitt

Marvel Loch Underground forms part of St Barbara Limited’s Southern Cross Operations which is located 360km (224 miles) east of Perth. Southern Cross Operations produces approximately 120,000 ounces of gold each year. Mining occurs in over 8 lodes using a variety of stoping methods including Uphole Benching, Long Hole Open Stoping, and Core and Shell.

Jan 1, 2012

By Keith Best

It has been said that when a person does something right no one remembers but when they do something wrong no one forgets. This statement, when applied to the explosives industry, has never been truer. Think about it.How many times have you seen a news crew reporting on how well a blaster is doing his/her job? Normally, all you will see is how bad things are going and how much “damage” is being done.

Jan 1, 2008

By Jeff Wachendorf

Due to the competitive nature of the coal industry we are constantly challenged to reduce costs associated with day to day operations. Every facet of the mining operation is scrutinized for cost reduction and possible efficiency increases. This paper will discuss the pros and cons of two different blasting methods. Buffer blasting has been an institution for many years at Spring Creek Coal and very successful in its application. Cast blasting arrived on a trial basis in 1998 and has produced very encouraging results. This paper will describe the design, drilling, and blasting methods currently used, and a comparison of these two methods.

Jan 1, 2001

By G E. Exedaktylos, Y Zhou

The complex and non-linear nature of blast fracturing has restricted common bract design primarily to empirical approaches. The code developed for this investigation simulates the pattern of interacting radial fractures from an array of blastholes, at various burdens and spacings, and in simultaneous and delayed modes. The resultant pattern is analyzed and a fragment adze distribution calculated.

Jan 1, 1989

By Dale L. Ramsey

The Pinkerton Tunnel Open Cut Project is part of the National Gateway Clearance Initiative improvement project to achieve a minimum of 6.4 meters (21 feet) of vertical clearance along CSX Transportation rail corridor so that double-stacked intermodal railcars can be transported between Mid-Atlantic States and their ports to Midwest Markets in the U.S.

Jan 1, 2014

By Corry Goumans, Dan Agostino

Photo 1. Demolition work on the Pitt River Bridge. The drill crew is using the 3800 Gardner Denver Air Track to drill the holes on the Bridge turning dolphin. The barge in the background is used for support.

Jan 1, 2013

By Alexander Hauck, Dimitri Jung, Uli Leiste

This paper describes results from small scale tests conducted to determine the distribution of impulse on target plates when subjected to loading due to the detonation of a buried mine. The tests were conducted with saturated sand, dry sand, and water as the loading media. Tests were conducted for flat plates and for plates with angled bottoms. Previous testing has shown that angled bottoms can reduce the total vertical impulse delivered to the vehicle significantly. Different stand off distances were investigated as well as loading of the targets both on center and off center. It is very important to know not only the total impulse delivered by a detonating charge but also how this impulse is distributed over the bottom of the vehicle. A complete understanding of specific impulse will permit those parts of the vehicle, taking the greatest amount of loading, to be sized properly. Experimental results were compared to analytical expressions provided by Westine and Tremblay.

Jan 1, 2010

By Lyall Workman

New mines are frequently located at altitudes above 3,000 meters (10,000 ft.). Drill selection must take the altitude effects into account, to insure high productivity and good bit life. In particular, compressors must be sized differently than for low altitude operation. A larger compressor is required to deliver adequate air to the bottom of the blasthole. Many drills in remote locations use diesel engines as the prime mover. Altitude effects on engine performance should also be considered.

Jan 1, 2007

By Peter G. Bellairs

The traditional concept of Optimum Drill and Blast is that it is achieved when ore is produced at the lowest unit cost and due to the complexities of most mining operations represents a band which extends either side of an overall cost minima. The above definition implies that Optimum Drill and Blast is static and once blasting is within the band around the cost minima then the process is optimised. However mining operations are not static with many events both long and short term impinging on the cost structure and productivity.

Jan 1, 1995

By Steven D. Sandbrook

A man by the name of Louis Binstock once said, “Too often the shortcut, the line of least resistance, is responsible for evanescent and unsatisfactory success.”

Jan 1, 2015

By L D. Lawrence, R S. Day, Gordon Coleman

Commercial emulsion explosives are typically characterized by their relatively high detonation velocities due to the intimacy of oxidizer and fuel and to their sensitization with glass microballoons. However, numerous blasting operations in softer, more porous rock formations are better fragmented with slower shooting explosives. Although mixtures of emulsions with large amounts of ANFO (60-80%) can considerably reduce the high velocities, little water resistance is achieved with low levels of emulsion blended with ANFO. "Water proof" blends containing typically 50 percent of emulsion become quite costly due to escalating powder factors in ANFO patterns. Blends of sensitized emulsions with 20-30 percent ANFO retain the high velocity characteristics of the emulsions as well as increased densities which can also adversely affect blasting results in softer rock formations. The introduction of a reliable and predictable on-site gassing process for sensitization and density control of repumpable emulsions, with or without added ANFO, offers the end user the option of supplying a final product more suited to his blasting needs. The capability to widely vary final product loading densities and consequently product detonation rates better tailors the final explosive to different rock characteristics. The beneficial advantages of this system in softer rock formations have been well documented. Overall comparison between these variable density products with typical repump emulsions containing solid density control will be reviewed. Besides the obvious cost advantages and safety advantages of these systems the end user is provided more definitive control of his blasting operation.

Jan 1, 1990