Search Documents

By Andrew F. McKown, Robert A. McClure

This paper will describe a trench blasting case history in close proximity to several adjacent structures, including a bridge abutment, railroad tracks, and utility pipes. Some design considerations involved in close-in blasting will be discussed, including allowable peak particle velocities and prevention of rock block movement. The importance of several trench blast round design factors is pointed out, including choice of explo sive to prevent propagation, maintaining a sufficiently high powder factor, and mucking out for maximum relief after every round. Vibration monitoring and good record keeping are shown to be important in order to evaluate blast problems and make modifications to round designs.

Jan 1, 1988

By Thierry Bernhard, Johan Finsteen, Charles Dowding, Mathias Jern

To bring some clarity to how different standards relate to each other a project was initiated within the European Federation of Explosives Engineers (EFEE). The first part of the project was a literature study and a survey including an evaluation of the answers provided by members of EFEE. The results were presented at the International Society of Explosives Engineers (ISEE) conference in Denver 2020 as well as the EFEE conference in Helsinki in 2019.

Feb 1, 2020

By L. Wilson, M. Kotzel, T. Pienaar

An empirical equation is presented for the maximum airblast from unconfined charges. This has been tested at a number of sites and with charges ranging from 0.1kg to 311kg. The equation is developed to predict community response to potential explosive test range sites and the testing has added to our knowledge of the effectiveness of mitigating measures. The first site had 10m to 15m high walls that were intended to ameliorate the airblast. These walls functioned to a limited extent and reduced the airblast levels by 2dB to 5dB. The airblast was affected somewhat by topography. Noise levels at the nearest residences exceeded 130dB for charges larger than 1kg, whereas the vibration levels were very small. Formal complaints were received where the airblast level exceeded 128dB as per conventional expectations. Pedestrians and pets in the suburbs were startled by the blasts, emphasizing that the community response is much more sensitive to noise and airblast than vibration levels. The maximum airblast levels were too high for this site to be used on a regular basis. At another site, the airblast levels were significantly increased downwind by up to 10dB due to a moderate wind. A third site, at a quarry, produced unconfined airblast levels beneath the derived limits, but are much higher than the normal quarry blasting. By involving community forums there were no complaints, possibly due to desensitization by the normal blasting activities. The study has highlighted new areas for research in understanding the effect of noise, air blast and vibration on the low cost and informal housing typical in South Africa

Jan 1, 2011

By P A. Lang, J G. Ayotte, R W. Humphries

Atomic Energy of Canada Limited (AECL) has the responsibility for research, and development of technologies, for the safe and permanent disposal of Canada's nuclear fuel wastes. As part of this comprehensive program, AECL is constructing an Underground Research Laboratory (URL) near Lac du Bonnet, Manitoba, to evaluate aspects of the concept of waste disposal deep in stable geological formations. No nuclear wastes will be used in the URL program.

Jan 1, 1986

By Matthew Graham, Tapan Goswami, Geoff Brent

In dragline coal mining operations, throw blasting is used for the controlled placement of overburden to maximise coal exposure rates or to minimise overburden removal costs. This may necessitate sacrificing thin coal seams, generally less than one metre in thickness, which are often present in proximity to the main coal seam. This represents not only a significant loss of potential revenue and profit but also a waste of a valuable energy resource.

Jan 1, 2010

By Brian Sandhuas, Robert McClure

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009, one North American Quarry and Construction Business experienced a series of flyrock incidents. In the spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

By Matthew Clay, Colin Chambers, Susan Hookham

Opencast (quarries) and underground mines around the world use blasting methods to mine valuable ore. Traditional blasting systems use technologies such as electric delay detonator systems (developed in the 1950s) and non-electric detonator systems (developed in the 1970s) to initiate a detonation train to blast rock more effectively, and so retrieve valuable product more efficiently. However, the lack of precise control over blast timings with these approaches can result in undesirable outcomes such as significant flyrock, excessive ground vibration, uneven grade of rock and misfires (in which sections of the blast can remain unfired). The development of Electronic Initiation Systems (EIS), first used in the 1990s, introduced a higher level of control over the blast. These systems greatly reduce the negative issues associated with blasting. However, this precision introduces complexity, and with this complexity comes difficulty in demonstrating the predictability, safety and reliability of such systems.

Jan 1, 2017

By Ruilin Yang

Explosive blasting is a widely used method for rock breaking, recognized for its energy efficiency and cost-effectiveness. Despite its advantages, the efficiency of blast energy can vary significantly between different blasts. This paper introduces a new blast efficiency index to assess the energy efficiency of rock blasting, incorporating factors such as explosive consumption, the energy required for fragment surface generation (based on fragment size distribution), and the strength reduction of rock fragments due to blasting. Several examples presented in this paper demonstrate the calculation of the blast efficiency index using data from the literature. The findings indicate that blasting may be the most efficient method for rock breaking compared with direct mechanical techniques of rock breaking used for excavation. On the other hand, blasting is much less efficient compared with the controlled fracturing, such as the cleavage and fracture toughness testing, which highlights the significant potential to further enhance the efficiency of explosive energy usage for rock fragmentation during blasting. The proposed blast efficiency index can be integrated with advanced blast modeling techniques to optimize blast designs, thereby increasing the effective utilization of explosive energy for rock fragmentation and fragment strength reduction.

Jan 26, 2026

By Roland Alford

The ballistic pendulum is a well-established piece of test equipment originally developed for estimating the velocity of bullets and projectiles. When trying to understand the effects of different tamping methods on explosive performance, the ballistic pendulum is an excellent tool allowing calculation of explosive charge impulse. Most ballistic pendula for this application are limited to narrow impulse ranges as the pendulum mass determines the angle of swing; and a mass capable of being moved by a small charge would be far too small for a larger charge. This paper describes a modular design (the Alford Modular Ballistic Pendulum) which overcomes this problem.

Feb 6, 2023

By David Scutt, David Noon

Blast crews are exposed to a number of major hazards including explosives and chemicals, ground conditions, machinery, unique work environments and specific blasting hazards such as fly rock and misfires. Unfortunately, injuries caused by sudden and/or unexpected movement of ground are continuing to occur. Blast crews are not equipped with the knowledge or tools to understand whether a high wall that they are planning to work under is safe.

Jan 1, 2011

By Shazad Hosein, William J. Birch, Robert Farnfield, David Jameson, Catherine E. Johnson

The current and consented quarry workings at a slate quarry in North Wales {UK} intersect old long abandoned underground slate mine workings. The old underground slate mine contains the remains of World War II buildings used to house artworks to protect them from war damage. Over the past 20 years, there have been a number of roof falls in the old underground slate mine, which have damaged the buildings and make general access unsafe. From observation of the timing of these falls, they occurred in the mid 2000’s. The purpose of the exercise was to determine the possible relationship between blast vibrations experienced on the surface and those experienced on the roof of the abandoned mine caverns. Thus preventing the need to regularly monitor in the old mine workings. In order to achieve this, a rigorous geotechnical assessment of the stability of the caverns was undertaken by a fully qualified Geotechnical Engineer. Once it had been determined that it was safe to do so, 3 “MEMs based” blasting seismographs were attached to the roof, in accordance with the instruction of the geotechnical engineer. In addition, 8 “MEMs based” blasting seismographs were deployed at various locations on the surface. The trial blast comprised of 51 blastholes, with charges varying between 46kg [101lbs] and 124kg [273lbs] of bulk emulsion explosive. The blastholes were in 4 rows of holes. The blast was connected using shock tube 25ms, 33ms and 65ms delay period relay detonators. The minimum distances from the blast to the surface and underground monitoring points were 78.1m [256 ft] and 114 m [374 ft] respectively. The results from the three underground monitoring locations in terms of resultant peak particle velocity was 4.42 mm/s [0.174in/s], 3.47 mm/s [0.137in/s], and 4.69 mm/s [0.185in/s]. In line with previous research, it was determined that the underground results [when compared on a “like for like” basis in terms of scaled distance] were lower in amplitude than the surface results. In this case by a factor between 0.47 and 0.87, averaging 0.68.

Jan 21, 2025

By Robert Hopler

True there is a certain proportion of nitro-glycerin in dynamite cartridges, but the dangerous explosive is scientifically compounded with wood pulp and some other ingredients in such a way that it can be absolutely depended upon not to explode accidentally if our simple and plain instructions for its use are complied with.

Jan 1, 2012

By Jeremiah Cohn, Rachel L. Bauer, Catherine E. Johnson

Water is frequently used in explosive applications to increase explosive performance and reduce air overpressure. Water tamping can enhance cutting abilities of shaped charges in demolition and increase impulse of kicking or breaching charges. In explosive disposal, water is used to suppress air overpressure and reduce noise. Despite its widespread use, the specific effect of water placement, whether in front of or behind the explosive, has not been studied. This work evaluates the directional effects of water placement on blast performance using 400-gram sheet explosive charges in five configurations: no water (control), rear-only water (tamped), front-only water (pushed), water on both sides (confined), and a thin front-and-rear water layer (low mass confined) to assess reduced mass effects. Water was sealed in plastic bags and held in position with custom 3D-printed cages to ensure consistent geometry and contact. A modified ballistic pendulum consisting of a hanging steel W-beam was used to evaluate impulse transfer, with high-speed video capturing swing velocity. Air overpressure was recorded using a seismograph microphone. Rear-only water (tamping) increased beam swing velocity by 69% over the control while confinement with water on both sides increased performance by 12% at a 2:1 water-to-explosive ratio and by 50% at 4:1, though it still underperformed the tamped-only configuration. Pushed water alone did not increase beam momentum and reduced tamping effectiveness by 19% when combined. Seismograph microphone data showed that pushed and low mass confined water configurations produced some of the highest air overpressure levels (up to 139.2 dB), while tamped and control charges produced lower levels (~134–136 dB), suggesting that pushed water may amplify, rather than mitigate, air shock transmission. These findings show that water placement has a strong directional influence on blast dynamics: water behind a charge enhances energy transfer to the target, while water in front provides limited or potentially counterproductive mitigation. This study advances understanding of water–explosive interactions and will lead to more effective charge designs for breaching, disposal, and demolition.

Jan 26, 2026

By Agne Rustan

The goal of this paper is to describe Fragblast 10 for those who did not have the opportunity to attend the Symposium and also give some examples of new research findings used in practise in some countries throughout the world. Also some entertainment events from the symposium are described.

Jan 1, 2013

By Dirk Voogt, Quentin Steyl, D. Scott Scovira

A South Africa iron ore mine reported a decline in blast performance and ore and waste fragmentation. Preliminary investigation by the explosives services company found that the straight gassed bulk emulsion was breaking down and collapsing inside of some loaded slept blastholes. The bulk emulsion loaded at the subject site was manufactured in country and shipped to various clients throughout the region, with normal function in blasts at other sites. Historically, the bulk formulation emulsion being used at the subject mine site also performed well and without issue. This raised the question, “why is this bulk emulsion now breaking down and not firing in blastholes?”. Iron ore mines are not typically associated with reactive or acidic ground, and ground sample reactivity testing against the emulsion confirmed this. So, if not reactive ground or acidic water, then what is causing the emulsion to breakdown?

Feb 6, 2023

By Winfried Rosenstock, Carlos Orlandi

Along the Pacific West coast of Latin America there are several large operations of metal mining activities. To mention only a few: Chuquicamata in Northern Chile moving daily approximately one million t of copper ore and waste, Cerro Verde near Arequipa in Peru, or lanaccocia. Apart from the coal deposits in north-east Columbia it is mainly to deal with metal-mining, which has due to geographical reasons relatively high cash-cost. This sector of mining is traditionally severely depending on the world-market.There are reasons to believe that the world-market will remain on a low price level and some analysts predict that in general the price-level will continue on low basis for the next decade. The cash-cost factor becomes therefore even more important as it already is. The goldprice development during the year 1999 illuminates that market changes can quickly lead to a severe crisis which forces the shutdown of mines with cash-costs close to or above the present market price per ounce. The breakdown of the cash-cost shows, however, that there are ways to overcome even the crisis like it struck the low-grade open pit goldmines around the world. Especially hitherto the “Electronic Option” is the only solution as the possible reduction using advanced technology based on the application of electronic detonating systems and newly developed special ignition procedures. The electronic option will lead to tremendous cost reductions similar to the results of research operations Thiess Contractors, Brisbane, Australia have carried out in Australia in 1998 and 1999. The electronic option allows a comprehensive integration of side effects of the blasting process which in the past could not have been achieved so far. Electronic initiation can achieve secondary effects which have an additional and positive impact on the level of costs. Appropriate application can enhance the production of material which will reduce the primary crusher costs or even make a primary crusher operation obsolete.

Jan 1, 2000

By Iván Aguirre Palacios, Jean Guiroux Toro, Eduardo Valdés Guerra

Currently, mining operations seek to be competitive in the market. To achieve this, one of the relevant factors is to maintain and improve the productivity of the extractive processes, mainly the loading from the point of opening of the mineral bodies. To do this, many techniques suggest reducing production costs, with the first opening of your free-face up raises. However, there are different ways to carry out these open-face raises up opening processes, where the balance of costs and construction time must be well planned to meet production plans. Operationally, there are different techniques for its construction, the most common being Blind-Hole up Raises and those with drilling with current production equipment that operates mining operations. This study shows a methodology and the results of the implementation of access stack drilling with production drilling rigs for a maximum height of 15 m with electronic detonators in production blasting. Within the methodology used, Qa/Qc processes were considered in cargoes with explosives, instrumentation for monitoring (vibrations), VOD registration, among others. As a result, of a total of 12 raises up blasts, construction time was reduced by 45% and the cost of drilling and blasting (P&V) was reduced by 50%, for up raises with a maximum height of 15 meters. Regarding the efficiency of the heights, this was 97% compared to the planned drilling design.

Jan 26, 2026

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling.

Feb 1, 2020

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling. It shows examples from daily work, in which possibilities for optimization, improved quality assurance, and work facilitation are explained. It presents the resulting potential by comparing process flows, before and after the introduction of Track & Trace solutions. What challenges will we face in the future concerning the use of T&T solutions? Will the tracking of explosives become the norm worldwide? What are future hardware and software developments to be expected? What impact will this have on the global supply chain?

By J. Aravena, S. Gajardo, M. Ayala, P. Salinas

Both, Teck Carmen de Andacollo (Teck CDA) and Orica, work hard in the implementation of new technologies available in the explosives industry and drilling and blasting techniques, with the objective of sustainable development of their operations, regeneration, and protection of the environment, also considering the welfare and relationship with the surrounding communities. The open-pit Carmen de Andacollo mine is located adjacent to the town of Andacollo. Therefore, both companies together have developed the implementation of different techniques and technologies to mitigate the impacts of mining operations in the community, considering an important part of this challenge to minimize the impact of their perception of blasting by reducing the level of vibrations and sound pressure (airblast), in addition to the control of dust and smoke, strengthening sustainable production in harmony with communities. The technologies and techniques that have been implemented are the installation of airblast and vibration monitoring stations stands out, whose database has records since 2011. Using the vibration database, different models were developed to predict the vibration level of blasting in its design phase, achieving a difference of 4.1% between the estimated and measured values in the last year. Two techniques stand out to minimize the ejection of material, "Hydraulic Dome" and "Dual layer blasting", the first consists of water irrigation on the surface to be blasted and the second is an unconventional blasting technique, which was awarded in 2015 for its results in the environment. Also pre-splitting engineering has been modified in a positive evolution, where through different configurations, the airblast has been reduced by 15% compared with records from 2011 to 2022. Finally, due to the impact of operational restrictions, such as days available to blast, number of holes, and powder factors, the wireless initiation technology was implemented, which allowed reducing the limitations in the loading, generating an improvement in terms of blasted materials over conventional systems. Understanding the restrictions and challenges in terms of impact on communities, the correct implementation of all these techniques is important, and in conjunction with collaborative work, it has been shown and validated that producing in a sustainable and sustainable manner is possible.

Jan 1, 2024