Search Documents

By Deane Boddorff

A 440 Volt AC power line is a typical power source for energizing electric blasting cap circuits in driving hard rock tunnels. A common misconception exists that the caps actually see 440 Volts. This paper describes an analysis of the entire blasting circuit determining the current flowing and the voltage drops through each component. If, from such an analysis, one determines that the current to the caps is too low or too high, the components that require changing are easily recognized.

Jan 1, 1975

By Fumihiko Sumiya, Hideki Hamashima, Shigeru Itoh, Shinya Tanaka

The detonation characteristics of non-ideal explosives, especially the emulsion explosives, are critically affected by the confinement of case. In this study, we focused the shock wave propagating in case as confinement factor. Therefore, the objective of this study was to obtain a better understanding of the influence of shock wave propagating in case on the detonation characteristics of explosives in laboratory scale.

Jan 1, 2007

By Peter Moser, Michael Messner, Florian Bauer

The existence of ammonia in underground blasting fumes was frequently measured in various field tests (6, 7). Ammonia in fumes with a TLV (threshold limit value) of around 30 ppm (slightly different in various countries) is a toxic gas but not considered to be a high risk for the underground work force as ammonia smells very itching and is extremely annoying. This might be the reason why ammonia is hardly measured in routine underground blasting fumes control. Another reason for the lacking measurement might be the circumstance that ammonia is a very reactive gas and the ammonia sensors available on the market are very cross sensitive to other gases like carbon monoxide. Nevertheless, especially since the introduction of bulk emulsion explosives in underground blasting, complaints from miners about ammonia in the blasting fumes increased. Research work by various institutions [8] around the world relates the ammonia in the fumes back to various mechanisms. Amongst others these comprise: a) non ideal (low temperature) detonation of explosives, with NH3 in the reaction products; b) reaction between rock and non detonated bulk explosives (especially when the rock is of a basic nature (high pH value); c) reaction between shotcrete and non detonated bulk explosives. Numerous blasting tests in an experimental underground set up have been made in order to check these hypotheses for ammonia origin in blasting fumes. None of them has been found to be responsible for sometimes high concentrations of ammonia in the fumes. The major reason for ammonia concentration in blasting fumes has been found in mine water of a high pH value (either natural or from using shotcrete). The mechanism identified is as follows: the moment a non detonated ammonium nitrate bearing explosive comes in contact with mine water of a high pH value, ammonia is formed immediately. The source for the undetonated explosive is twofold: firstly there is a certain spillage of explosives when the holes are charged (especially when using bulk products) and secondly not the entire explosives detonate completely. These undetonated remaining of the explosives end up in the muck pile after blasting. In case there is water of a high pH value the reaction between the explosives and the water starts immediately. This explains also the observation why ammonia can be measured in the blasting fumes quite a long time after the blast. The majority of the ammonia is not formed during the detonation; it is formed inside the muck pile even a considerable long time after the blast.

Jan 1, 2010

By James A. Bachmann, Christopher J. Gray

On December 26, 1994, at 1:00 am, Santa Fe Pacific Gold's Twin Creeks Mine experienced a major highwall failure involving over 2.5 million tons. The resulting effects of this slide were thousands of ounces of gold that were now deferred and an unstable wall above which made mining the slough material unsafe.

Jan 1, 1996

By Denise Clarke

Homeland Security Qualifications (HSQ) personnel were instrumental in developing the UK’s suite of Explosive Substances and Articles (ESA) National Occupational Standards (NOS) (also known as "competences") on behalf of the Standards Setting Body for Explosives, Munitions and Search Occupations (SSB for EMSO).

Jan 1, 2013

By Agne Rustan

This paper is intended to give a summary of the first ten Symposia on Rock Fragmentation by Blasting where the symposia activities were governed by a Steering Committee replaced at Fragblast 2 by an International Organizing Committee (IOC). At Fragblast 9 the name was changed to Fragblast International Organizing Committee (FIOC). Eighty four pages of statistical data about Fragblast 1-10 is documented on the Fragblast Website (ISEE.org).

Jan 1, 2014

By Mark Abernathy

When most people think of a motor vehicle accident, the direct costs resulting from that accident, such as vehicle repair or towing charges, are generally easy to quantify. However, the indirect costs associated with an accident are often overlooked. These indirect costs can take a tremendous toll on a company in more ways than you might think.

Jan 1, 2006

By Marco Larghi, Jurg Knobel, Braden Schmidt

Remote Avalanche Control Systems (RACS) which uses solid explosives has been used in Europe since 1996 and North America since 1999. With large destructive avalanches in transportation corridors, various States and Provinces have started implementing RACS into their summer construction projects to minimize traffic shutdowns. Since 2014 in North America, many of the projects are requiring the RACS deployment boxes to be removable by light duty helicopter for loading and summer storage. This is to further remove workers from the mountain tops, where inclement weather and Occupational Health and Safety concerns are widespread. We did not believe the method of flying primed charges under a helicopter was safe, so we developed a new charge container to deal with the issue.

Feb 1, 2020

By Bill Rose, Alan Foster

This paper will outline blasting as undertaken at the Flour Mill project in the Georgetown area of Washington, D.C. It will discuss the vibration and blasting problems found in blasting in high risk and highly populated areas, and the day to day methods used to minimize damage potential and still maintain adequate fragmentation.

Jan 1, 1979

By B. Papillon

There has been a veritable increase in the adoption of electronic detonators in the last few years. Electronic detonators offer several distinctive features over electric and non-el (shock tube) detonators including better timing accuracy resulting in excellent fragmentation and vibration control, certainly key mining parameters. The field programmability also helps in reducing the on-site magazine storage of detonators with diverse fixed delays. A typical electronic detonator may consist of a logic core, a communication interface, storage capacitor(s) and the ignition element. Being electronic components, the electronic detonators may be susceptible to RF or electromagnetic interference (EMI). RF sources are virtually everywhere: cellular phones/towers, radio transmission, microwaves, walkie-talkies, high voltage (HV) transmission cables and wireless networks with their characteristic frequency emissions. Safety issues prevail; e.g., whether the RF interference can cause premature or inadvertent firing whether directly or indirectly. From a reliability perspective, the RF interference may also impact on bus communications, e.g., during the logging, verifying, charging and firing phases. The deleterious communications disturbance may result in a misfire (non-firing of one or more of the detonators) which is terribly inconvenient for the mine operators and even pose a safety hazard.

Jan 1, 2009

By Robert Hopler

The use of electrical fuzes is rapidly superseding the old cap and fuse method of firing blasts. It is therefore desirable that the details of this kind of blasting should be more generally understood

Jan 1, 2006

By Jorge Cardenas, David Martinez

Blasting-induced vibrations can be predicted with high precision, allowing for the optimization of sequence design, delay timing, and charge configurations to minimize their indirect impact on rock masses. This optimization leads to a reduction in peak particle velocity (PPV) and dominant frequency at monitoring points. However, a crucial aspect of slope safety is estimating the degree to which vibrations influence stability through numerical modeling of the dynamic response. Slope stability is closely linked to rock mass strength, the predominant failure mechanism based on discontinuity orientation relative to the slope face, and the pre-existing stability conditions before dynamic alterations occur. Blocks, wedges, and planar failures tend to slide under lower vibration levels and are more susceptible to resonance, particularly in fractured and low-strength rock masses. To evaluate the interaction between rock mass and vibrations, photogrammetry and artificial intelligence were employed to identify discontinuity families at vibration monitoring sites. This data facilitated the development of artificial discontinuity networks (DFN), which replicated a discontinuous medium within a numerical finite element model. The input signal was recorded at the slope base using triaxial geophones and incorporated into a discontinuous numerical model. The output signal was estimated through finite element analysis and subsequently compared with geophone measurements taken at the same location. Based on real-world output signals, damping parameters and the model’s natural frequency were adjusted to align both frequency spectra. Using the calibrated parameters, vibration records from various blasting projects at different distances were applied as input signals until slope failure was induced, thereby defining maximum allowable vibration limits in terms of PPV and frequency at the monitoring point. This approach provided a framework for optimizing sequence designs, charge configurations, and delay timings to enhance slope safety and prevent failure due to blasting-induced vibrations.

Jan 26, 2026

By Tristan Worsey, Nathan Rouse, Daykin Schnell

The authors were retained by a proposed underground metals mine operation to evaluate the potential blast vibration amplitudes that could be generated at surface structures above the proposed mine. Literature reviews of published blasting documentation gave little information, data, or models on surface blast vibrations produced by underground mines. At the client’s request, the authors contacted a number of underground mining operations to evaluate interest in sharing blast vibration data with the authors so that the authors could develop an underground-to-surface blast vibration regression equation.

Feb 1, 2020

By Randy Martin, Jessie Bonner, Peter Boyd, Mark Leidig, Timothy Rath

We conducted the Vermont Damage Experiment in central Vermont during July 2008. Five single-hole explosions with yields ranging from 60.8 kg (134 lbs) to 122.5 kg (270 lbs) were detonated in homogeneous, low fracture density granite. The goal of the experiment was to quantify the different levels of rock damage around the source and then relate the seismic wave generation to the degree and distribution of damage and fragmentation. In addition, explosives with different velocities of detonation (VOD), including black powder (0.53 km/sec; 1737 ft/sec), heavy ANFO (4.8 km/sec; 15734 ft/sec), and COMP B (8.1 km/sec; 26574 ft/sec) were detonated to relate the VOD to seismic wave generation and extent of damage zones in the source region. Over 120 seismic stations were deployed to record the explosions at distances between 5 m and 30 km (15 ft to 19 miles).

Jan 1, 2010

By Brent Blanchard

As most veterans of our industry are aware, explosive demolition by its very nature is often a challenging proposition. Even under the best of circumstances, proper planning and care must be taken during a variety of processes to ensure a safe, successful result. However, every now and then a project suddenly arises where safety, timing and cost factors combine to form a critical scenario requiring rapid execution in an environment far more challenging than the norm. On these occasions, the stresses, complications - and most notably the dangers - related to the industry increase exponentially, and conspire to test the mettle of even the most seasoned experts.

Jan 1, 2003

By John A. Franklin, Tom C. Palangio, Norbert H. Maerz

WipFrag systems I and II have become the world standard in photoanalysis systems to measure fragmentation. Mines, quarries and excavating contractors can now easily measure blast results and track the progress of optimization efforts. This technology was developed and evolved to allow automatic measurements of the size distribution of patiicles on moving conveyors, in truck boxes and on crusher feeds. Production machinery can now be controlled by photoanalysis results and multiple cameras allow various locations to be monitored by a single system. Blast designs can be monitored on a shot by shot basis. Changes in delay times, explosives, patterns and hole sizes can be quickly evaluated. Along with this measurement capability has come a heightened awareness of the importance of “optimum size” and uniformity of particles for lowest cost production and material handling efficiency. In the past, savings in the “drill / blast” cycle of the operation were sometimes overshadowed by downstream production costs related to fragmentation. Now total production costs can be compared with fragmentation sizes which will immediately show the trend towards optimum size for economical production. No cost reduction program can be complete without this critical information.

Jan 1, 1997

By Ali Kahriman

This paper presents the results of ground vibration and air blast measurements from tunnel blasting activities during the construction of the Beylerbeyi-Kucuksu waste water tunnel under a residential area in Istanbul, Turkey. Within the scope of the study, the blasting pattern of the tunnel was engineered using Tunnel2000 design software and field studies and measurements for evaluating the productivity and safety of shots were realized for 136 rounds. During the study, the advance of the tunnel, face condition, ground vibration, air blast and neighbours’ complains and comments after every round were observed and the tunnel pattern was improved. Finally, an empirical relation for this tunnel route was developed between scaled distance and maximum amount of explosives, to continue activities in a safe and productive manner.

Jan 1, 2006

By Diogo Fonseca, José Manuel, Nuno Fernandes, Blessing Taiwo

This research focuses on enhancing the synergy between blasting and primary crushing operations in quarries. A blast operation at dstgroup aggregate quarry in northern Portugal was simulated to fine-tune blasting techniques aimed at optimizing fragmentation indicators. The methodology involves conducting precise blast drill hole surveys, generating detailed terrain 3D models, and integrating these models into blast simulation software to enhance accuracy and optimize production efficiency. The study applies these simulations to test blasts, evaluating improvements in cost-effectiveness, crusher power consumption, and fragmentation efficiency using both aerial and terrestrial image analysis technology. The quarry key performance indicators (KPIs) guide the blast design simulations, ensuring practicality and relevance. The case study blast revealed that implementing optimum blasting techniques can enhance crusher throughput, reduce operational costs, and improve safety. This paper is part one of a three-part technical series where we aim to create a sampling procedure and establish a reliable baseline for the current state of operation. This baseline will be used in subsequent follow-up technical papers to make recommendations and improvements. The outcome of this study provides a framework for quarry operations seeking to enhance their efficiency.

Jan 21, 2025

By Wm. Reisz, Raphael Trousselle

We are now well into our second decade of commercially available electronic initiation systems. Over this time, the technological advances have made electronic systems a very practical option for a wide variety of blasting applications.

Jan 1, 2011

By Timothy Stark

At present blasters are strictly liable under tort law for personal injury and property damage caused by ground vibrations and/or air overpressures. The application of strict tort liability to vibration and air overpressure damage has resulted in litigation that has hampered and probably will continue to hamper the blasting industry. There are many case histories in which blasters have been sued for the appearance of cosmetic cracking, some of which have involved frivolous claims and marginal expert testimony (Oriard 1999). This litigation has resulted in additional costs to the blasting and construction industries and the American public because there are usually many plaintiffs involved and each case is usually adjudicated separately instead of under a class-action format. It is proposed herein that blasters not be held liable for vibration or air overpressure damages unless their conduct is proven to be negligent. A number of reasons are presented for raising the legal standard from strict liability to negligence including: (1) improvements in blasting technology that allow blasting to be conducted without substantial risk of damage and if damage does occur it is likely to be cosmetic, (2) establishment of conservative ground vibration and air overpressure damage limits for typical structures, and (3) established industry standards for construction blasting.

Jan 1, 2002