Search Documents

By H. W. Wainwright

.1. The purification pilot plant and the equipment, solution, and gas cycle used for removing hydrogen sulfide and carbon dioxide are described. 2. As sulfur recovery is necessary in any large Fischer-Tropsch plant, pilot-plant runs were made at 300 p.s.i.g. to study the efficiency of tri-ethanolamine solutions in removing selectively hydrogen sulfide from gases containing varying amounts of carbon dioxide. 3. Aqueous solutions of TEA of 20, 30; 35, and 50 percent were investi¬gated. Data indicate that 30 to 35 percent is the optimum concentration if both selectivity and economy are considered. Slightly better selectivity is obtained with the.20 percent solution, but steam consumption is greater owing to the higher solution rates. Results from our pilot plant runs indicate that a 50 percent solution not only produces an acid gas of lower hydrogen sulfide content but also requires high solution rates to effect hydrogen sulfide purification. 4. Data from 37 runs using TEA are presented in tabular form. In addition, the data are correlated and presented in three sets of curves. By using these curves, it is possible to calculate the compositions of the purified and acid gases for various raw gas mixtures. 5. In cooperation with the Southern Natural Gas Co., investigations were carried out at 300 p.s.i.g. on the simultaneous removal of hydrogen sulfide and carbon dioxide, from gases using various concentrations of diethanolamine. 6. Data from 17 runs employing 20, 30, and 40 percent DEA are reported in both tabular and graphic form. 7. A comparison of the data from one DEA run made at 200 p.s.i.g. with those from the runs operating at 30O p.s.i.g. shows float the absorption capacity of the solution, and, hence, the steam requirements per gallon are about the sage for both pressures. .The only real advantage of the higher pressure is the additional volume of gas that can be treated. 8. The quantity of steam needed to reactivate fouled TEA and DEA solutions increased as the reactivator pressure was increased about 1,0 to 1.1 pounds of steam was required for each gallon of circulating solution when the reactivator was operated at 5 p.s.i.g. 9. A curve is included that shows the effect of the hydrogen sulfide con-centration in a lean 35 percent TEA solution on the hydrogen sulfide content of the purified gas and on steam consumption for reactivation. 10. Both TEA and DEA reduced the organic sulfur content of the raw synthesis gas considerably. Analyses of the lean amine solutions showed a gradual build up of sulfur compounds, indicating that the compounds formed by the amines and organic sulfur do not break down under the ordinary operating conditions of the reactivator. 11. Considerable operating difficulty was encountered in the pilot plant owing to foaming of the amine solutions. Laboratory experiments in which the effectiveness of certain antifoam agents was studied showed Alkaterge C to be most promising for the particular conditions studied.

Jan 1, 1952

In the United States water pollution resulting from mining activities has long been recognized as a major environmental problem Mine drainage pollution results from many types of mining activities and includes both physical (i e , sedimentation) and chemical (i e , acidification, metal contamination, etc ) pollutants Active and abandoned surface and underground mines, mineral processing plants, mine and processing plant waste disposal areas, haulage roads, and tailing ponds are typical sources of mine related water pollution (130) One of the most serious pollution problems arising from mining activities is acid mine drainage resulting from the chemical reaction of sulfide minerals (commonly iron sulfides) and air in the presence of water Acid mine drainage is commonly associated with coal and hard rock mining areas in the United States In general the more serious and extensive acid mine drainage problems exist in the more humid coal regions east of the Mississippi River (11) In 1964 the U S Department of the Interior, Fish and Wildlife Service, reported that acid mine drainage adversely affected fish and wildlife habitat in 9,477 kilometers (5,890 miles) of streams and 6,062 hectares (14,967 acres) of impoundments in 20 states in the United States (64) Of the total affected waters, coal mining operations accounted for 97 percent of the acid mine drainage pollution reported for streams and 93 percent of that reported for impoundments In 1970 more than 19,308 kilometers (12,000 miles) of streams in the United States were reportedly significantly degraded by mining related pollution (130) Of the total affected kilometers, 16,920 kilometers (10,516 miles) or approximately 88 percent were located in the Appalachian coal region (Pennsylvania, West Virginia, Ohio, eastern Kentucky, Tennessee, Maryland, and Alabama) In addition, more than 965 kilometers (600 miles) of streams reportedly were degraded by coal mining in states in the Illinois, Western Interior, and Rocky Mountain coal regions The remaining portion of the stream pollution resulted from the mining of (1) copper (california, Montana, Nevada, New Hampshire, Tennessee, Virginia, and Wyoming), (2) lead and zinc (Colorado, Idaho, Kansas, Missouri, Montana, Oklahoma, and Tennessee), (3) uranium (Rocky Mountain States), (4) iron (Lake Superior iron region), (5) sand and gravel (all states), (6) phosphate (Florida and other states), (7) gold (Alaska), (8) bauxite and barite (Arkansas), and (9) molybdenum, gold, and other metals (Colorado) Abandoned mines and abandoned mine waste disposal areas contribute a large portion of the total pollution resulting from mining activities Numerous abandoned underground mines are located throughout the United States and many are discharging mine drainage pollutants In 1966 the U S Bureau of Mines estimated that more than 88,000 inactive and abandoned underground mines were in existance (126) A listing of these mines by state is presented in Table 1 0-1 More recent estimates indicate that this list is incomplete In Colorado alone there is

Jan 1, 1975

By F. R. Cattoir

The Federal Bureau of Mines refined chromium from an aqueous electrolytic process in molten sodium chloride-chromium chloride electrolytes. Oxygen and nitrogen contents were reduced by a factor of 10 to 40, but most other impurities were little changed. The product usually contained a little more iron than the feed. Since iron was entering the bath from the iron pot and the graphite liner at a nearly constant rate, contamination of the chromium deposits by it was more serious at low currents and deposition rates. A few runs in an iron cell with a nickel liner yielded chromium containing one half as much iron as the feed, but up to 1.5 pct. nickel. In all cases the anode feed lay in the bottom of the container, which itself was used as the anode connection. With a 12-in. cell, variations in applied voltage from 0.05 to 1.5, in current from less than 10 to over 100 a., and in initial cathode current densities from less than 100 to over 2,000 a./sq.ft. had little or no effect upon the analysis of the metal produced) except for iron content. Changes in bath analysis from 3 to 11 pct. chromium were also without effect. These changes did bring about large differences in the physical forms of the crystals obtained. The thick heavy crystals produced at low voltage and current contained voids which made them difficult to leach free of chlorides. Easiest to leach were the thin leaf-like crystals obtained at around 1 v.

Jan 1, 1960

By Juel H. Stears

Research was done to determine if a hydraulically operated penetrometer developed by the Bureau of Mines could be used to estimate the roof-bolt anchorage capacity of mine roof rock. Tests were conducted both in the laboratory using cement cylinders and underground in shale rock. Hardness readings were measured by the penetrometer around the periphery of the bolt holes at the anchorage horizon. Roof bolts Nere then installed and subjected to an anchorage test. The results showed that the penetrometer readings could be used to determine the optimum stratum for roof-bolt anchorage but could not be used to make an accurate estimate of the anchorage capacity.

Jan 1, 1965

By Keith L. Harris

Economic activity in the United States picked up in the third quarter, according to the latest estimate released by the Department of Commerce. Real gross national product (GNP)--the Nation's output of goods and services--grew at a seasonally adjusted annual rate of 4.3%, or $17.6 billion, compared with a rate of 1.9% for the second quarter of 1985 and 1.6% for the third quarter of 1984 (table 1). The 4.3% rate is one percentage point above the preliminary estimate reported in the August/September issue of Minerals and Materials. Most of the upward revision was due to the change in business inventories and Government purchases, while the figure for net exports was revised downward substantially. The 4.3% growth bettered by 1.5% the average rate of growth in GNP from 1974 through 1984 and was 1.1 % above that of the period from 1975 through 1984 and 0.7% above that of 1980 through 1984. Of importance to the minerals industry was the $14.4-billion growth in personal consumption expenditures, $10.2 billion of which was for durable goods (especially domestically produced automobiles) and the growing residential investment. The net export deficit continued to grow, however, and investment in nonresidential structures, producers' durable equipment, and business inventories declined. Prices, as measured by the GNP fixed-weighted price index, increased at an annual rate of 3.1% in the third quarter, compared with 3.9% in the second quarter. The slower rate of inflation resulted mainly from a decline in energy prices, following second-quarter increases. Fourth-Quarter Prognosis Many of the economic data available for October and November indicate that the economy is growing modestly and will continue to grow over the next 3 to 6 months. The composite index of leading indicators, designed to predict economic activity within 3 to 6 months, rose 0.3% in October, the sixth consecutive monthly advance, according to the Department of Commerce. Six of the 11 available leading indicators were positive: Stock market prices rose, as did sensitive material prices, credit outstanding, and manufacturers' new orders for consumer goods and materials; initial claims for unemployment insurance decreased, and firms were getting slower delivery of goods. Four of the indicators were negative: Business formations, homebuilding permits, contracts and orders for plant and equipment, and money supply all declined. The average hours worked per week, already at a high level, remained unchanged.

Jan 1, 1985

Ground-water and tailings pond monitoring in the Upper Santa Cruz Basin Mines Task Force's Special Studies Area has been performed to determine the nature and extent of aquifer contamination from copper tailings pond's recharge in the basin. A monitoring program for each of three mining areas (Mines A, B, and D) was developed. Analysis of data shows that recharge from Mine A's ponds has caused increased hardness, sulfate and total dissolved solids in local ground water. However, pumpage in the area has controlled most of the water's movement. Pond recharge from Mine B has led to similar conditions, and the degraded water is moving towards a local public-supply well. Pumpage from Mine D's interceptor wells is controlling some, but not all, of the movement of recharge seepage from Mine D's ponds. Recommendations include the need for enhanced monitoring programs at each current mine site, development of a monitoring program for Mine C's area, development of water budgets for all mines, investigation of tailings pond compaction and sliming, establishment of mine closure plans for containment of recharged pond water, and the need for additional interceptor wells in several locations.

Jan 1, 1983

By James W. Wade

This paper describing the mining practices at the Tintic Standard mine is one of a series being prepared by the United States Bureau of Mines. In the preparation of this paper each subject has been presented by the engineer in charge. L. R. Dobbs wrote the part pertaining to tae technique of square-set mining, J. M. Snow the part on geology, and M. D. Paine, the part on ventilation. All of the drawings are the work of H. W. Waterfield of the engineering department. The statistics of the Tintic district ware prepared by A. G. MacKenzie. Each writer has attempted to show the difficulties that arise in operating and the practices used to overcome them.

Jan 1, 1930

By John R. Duda

The Bureau of Mines is developing estimates of capital investment, operating cost, and selling price for underground mines producing bituminous coal by various mining methods. This study estimates the required capital investment, operating costs, and selling prices for two hypothetical mines designed to produce 1.5 and 3 million tons per year (MM tpy)3 by using a longwall system in conjunction with a continuous-mining system. The coal properties being mined are assumed capable of sustaining a 20-year product Lon period. Wages and union welfare payments used in this study are those in effect as of December 6, 1975, as set forth under the National Bituminous Coal Wage Agreement of 1974. Costs of materials and equipment are based on January 1976 Indexes. Initial capital investment is $33.8 million for the 1.5-MM-tpy mine and $61 million for the 3-MM-tpy mine. Capital requirements, including deferred investments, were estimated to be $52.5 and $94.2 million, respectively. These figures translate into total capital investments of $34.87 and $31.31 per ton of annual production. Assuming a desired 15-percent discounted cash flow rate of return, with Federal income taxes at 50 percent, the required selling prices would be $12.06 and $10.94 per ton for the 1.5- and 3-MM-tpy mines.

Jan 1, 1976

By J. M. WADSWORTH

The purpose of this bulletin is to describe the methods of constructing and operating representative types of plants in the United States used for removing the light hydrocarbons from petroleum by continuous distillation, such plants being commonly known in the trade as topping or skimming plants. In the discussion of each plant an endeavor has been made to arrange the text similarly in order to facilitate comparison and to emphasize the important features. The various experimental values for the specific and the latent heats of the oils apply approximately to the oil treated. Careful experiments with each oil and its commercial fractions were not justifiable in view of the purpose of this report. It is regretted that limitations for recording data at the different plants made impossible the determination of a heat balance for each, which would have provided an equitable method of comparing efficiencies. The writer has confined himself to a comparison of the relative efficiencies of the distilling apparatus alone by the following method: Effi . f till d tt" _ Heat theoretically required. ciency 0 SIS an se mgs - Heat content of fuel consumed. The plants described are all in California where the topping industry has had its growth accentuated by the character and the use of the oil handled. The scarcity of suitable coal made the adoption of other fuel necessary, and the heavy oil of California supplied the need. To raise the flash point and to dehydrate this oil, various plants have been developed. However, the topping industry is represented in other fields; the Roxana Petroleum Co. of Cushing, Okla., and the Warner-Quinlan Asphalt Co. of New Jersey, are operating Trumble plants, and Texas and Oklahoma operators have been experimenting with different pipe retorts for continuous running. In addition to the reasons for topping cited above, in California topping has other purposes which give the plants practically a universal field in the oil industry. These additional purposes are (1) to remove the lighter constituents of the oil prior to storage for a long period, thus reducing the losses from evaporation, (2) to dehydrate and clean the oil, and (3) in conjunction with a complete refinery, to remove the lighter fractions cheaply and quickly, leaving a residue to be rerun for lubricants, coke, and other products. The reader in studying a plant for possible adaption to his own use should note that local considerations enter into the design and size of a plant. Several questions present themselves, as follows: 1. What type is suitable for the oil? 2. How much money is available for construction? 3. Will the volume of residuum be large enough for heat exchange with the crude? 4. Can the heat content of the vapors be used to reduce the cooling-water requirements? 5. What method will best recover the heat from stack gases? 6. Are the various pieces of apparatus adequate in size and best adapted to their purpose? 7. Is every possible provision made for the recovery of waste heat? 8. What products will be made, and what volume of each? 9. Is there provision for the recovery of light vapors? 10. Will the saving of fuel justify the capital and maintenance charges on the regenerative apparatus contemplated? It is regretted that information concerning the operation of topping plants with eastern and Middle West oils is not available. The writer carefully canvassed the Middle West, but did not find a plant where operation had progressed beyond the early experimental stages and reliable figures could be furnished. The reader will find fuel economy and heat recovery emphasized throughout the descriptions. The conservation of the available petroleum supply is of the utmost importance, and the Bureau of Mines presents this paper to encourage the hearty cooperation of operators to that end. The Baume gravity scale used throughout the report is that of Tagliabue with a modulus of 141.5 for conversion to specific gravity.

Jan 1, 1919

By D. D. Harbuck

To decrease reliance on foreign sources for the strategic and critical metals gallium and germanium, the U.S. Bureau of Mines identified and developed processing technology for two domestic sources of these metals: a Tennessee zinc residue and a Utah ore. Sulfuric acid (H2S04) solutions were used to solubilize gallium and germanium in both sources. Statistically designed experiments showed that the most important parameter for high metal extraction from zinc residue was the H2S04 concentration. At a concentration of 2.9M H2S04, 95 pct of the gallium was extracted, and at a concentration of 0.6M H2S04, 73 pct of the germanium was extracted. Controlled H2S04 concentration was also the key for high metal extractions (97 pct Ga, 87 pct Ge) from the Utah ore. Such control was achieved using a two-stage countercurrent leach circuit. Testing showed that the insoluble germanium in both the residue and ore was tied up with silica. Several methods for overcoming this problem are given. To recover gallium and germanium from the leach solutions, the solvent extractants octylphenyl acid phosphate (OPAP) (for gallium) and LIX 63-OPAP (for germanium) were identified. These extractants were tested in separate, continuous, solvent-extraction circuits yielding a gallium recovery of 94 pct and a germanium recovery of more than 90 pct.

Jan 1, 2010

By James F. O'Neill

Brown iron ore deposits in Quitman County , Ga . , were investigated by the Federal Bureau of Mines in cooperation with the State of Georgia , Department of Commerce , and the University of Alabama . Ninety- one holes were drilled , having an aggregate footage of 2,188 feet ; seventy- one holes penetrated 248 feet of iron mineralization . Average thickness of the ore zone was 3.5 feet under an average thickness of 14.7 feet of overburden . The drilling developed inferred reserves containing nearly 30 million long tons of crude ore with an average analysis of 28 percent iron plus minor quantities of manganese . Test work done by the Bureau on the crude ore samples indicated that they would upgrade by current log washer practice , with the use of a 1 /8 - inch screen , and yield 4.4 million dry long tons of concentrate with an average analysis of 52.1 percent iron plus manganese . The weight recovery obtained was 14.7 percent . Research studies made by the Bureau showed that the weight recovery would be increased by changing the screen size without any appreciable sacrifice of grade . The average weight recovery was increased to 18 percent with a 10 - mesh screen and 22.8 percent with a 20 - mesh screen . Screen tests studies indicated that there was no appreciable interlocking of the iron and manganese minerals and the clay and silica waste particles of the materials retained on a 200- mesh screen . Clay was prominent in micron - size slimes . Silica was deleterious in the minus 20 - mesh size .

Jan 1, 1965

By D. A. Buckingham

The Bureau of Mines evaluated potential availability of domestic nickel from 23 deposits, Evaluations included an estimation of in situ and recoverable resources, applicable mining and processing technologies, and capital and operating costs. Discounted cash flow analysis with a 15-pct rate of return was used to determine the average total cost of production of each operation, Identified in situ resources contain 9.0 million metric tons (t) of nickel; 5.5 million t is recoverable as nickel metal or ferronickel. Demonstrated in situ resources contain 8.2 million t of nickel; 4.8 million t is recoverable as nickel metal or ferronickel. No nickel is available at a total cost of production equal to the January 1983 market price of $3.24 per pound. Analyses indicate that potential annual production can only meet current consumption levels at a total cost of production of $7.60 per pound of nickel, Nickel's availability is contingent on (1) successful adaptability of nickel processing methods to domestic resources, (2) location of a smelting facility, and (3) marketability of byproducts and coproducts. Analyses were performed on the effects of byproduct and coproduct revenues, energy, labor, and transportation costs, and metallurgical recoveries on nickel's availability.

Jan 1, 1984

By W. J. Fullerton

This paper is one of a series prepared for the United States Bureau of Mines discussing the methods used in crushing and grinding materials for cement manufacture, and deal particularly with the methods used at the Howes Cave plant of the North American Cement Corporation. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By Alvin M. Cummings

"INTRODUCTION During July and August 1943, the Bureau of Mines undertook an investigation of the Trego lead-zinc mine, near the town of Platteville in Grart County, Wis. as part of a general investigation of the zinc-producing area of southwestern Wisconsin. The work was done when every effort was being made to increase the production of metals important to the nation's war program.The Bureau of Mines completed eight churn-drill holes and sampled mineralized faces in the mine workings to determine if further exploitation was justified in an area between the mine and a zone previously drilled to the east.Following the investigation described herein, intermittent operations were resumed. Except where otherwise stated, this report describes conditions only to the time of completion of the Bureau of Mines investigations.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.The investigation described in this report was conducted under the immediate supervision of the author and 0. W. Terry, mining engineer of the Bureau of Mines, with the assistance and advice of E. D. Gardner, re¬gional engineer, and E. P. Barrett, district engineer. Final data were prepared under the direction of Paul Zinner, acting chief, Minneapolis Branch, Mining Division.A. V. Heyl, Jr., and A. F. Agnew of the Federal Geological Survey cooperated with the Bureau's engineers and made lithologic studies required during the drilling program.The cooperation of W. N. Smith and O. E. DeWitt of the Vinegar Hill Zinc Co. and Francis Piquette of the Piquette Mining Co. facilitated the investigation to a great extent."

Mar 1, 1948

By Jerry W. Ramsey

The Bureau of Mines examined a low-, a medium-, and a high-volatile Pennsylvania anthracite by densimetric methods using four mesh si.s of each anthracite. Using high-pressure mercury the macropore volumes and distributions of these pore volumes determined, densities in mercury were calculated, and specific pore vo1.r. ware obtained from these mercury densities in conjunction with helium densities. The helium densities were also used with the ultimate analyses of these anthracites in calculating structural parameters by statistical densimetric methods. The effect of 106 or 108 rads of gamma irradiation in the presence of air and in vacuum upon the properties studied with two mesh sizes of each anthracite. Results of the statistical densimetric method seem to show some breakdown of condensed ring structural units at the lower irradiation level, with subsequent polymerization at the longer period of gamma irradiation. The structural parameters obtained also indicated that in going from high- to low-volatile anthracite, either the number of condensed rings per structural unit increased, or the degree of polymerization increased.

Jan 1, 1965

By W. P. Yant

This report describes result of a study of the carbon monoxide and particulate matter in the air of the Holland, Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development

Jan 1, 1941

By M. W. Von Bernewitz

The Bureau of Mines receives frequent requests for information on the treatment of mercury ores, but as its own and almost all other publications on mercury are out of print, the Bureau has prepared this circular on the metal for the prospector and operator of small mines and plants. Mercury, commonly though improperly termed ?quicksilver?, is the only common metal that is liquid at ordinary temperatures. Mercury is used in the amalgamation of gold and silver, in power boilers, explosives, friction-less bearings, laboratory apparatus, lamps, medicine, paint, rectifiers, and for ?silvering.? The last mentioned is being superseded by silvering with silver. The use of mercury boilers may increase when they are thoroughly understood, but amalgamation is -being replaced to some extent by the use of corduroy and other collecting mediums, such as jigs and flotation cells.

Jan 1, 1937

By A. F. Colombo

The western Mesabi range nonmagnetic taconites containing about 34 percent Fe were evaluated by the Bureau of Mines in a 900-pound-per-hour pilot plant employing a selective flocculation-desliming-cationic flotation technique. The flotation step was a reverse flotation process and involved the flotation of the gangue minerals. The objective of the research was to increase the availability of domestic raw materials for the iron and steel industry. The beneficiated ores yielded concentrates containing 62 to 64 percent Fe and less than 5.5 percent Si02 with accompanying iron recoveries that averaged about 75 percent. Comparable flotation results were obtained with either fresh or 80 to 90 percent reclaimed water. Recycled waters having turbidities as high as 5,000 ppm Si02 did not affect the flotation process. Reclaimed waters containing residual calcium contents of less than 10 ppm gave better flotation concentrates than those containing 15 ppm.

Jan 1, 1976

By J. J. Forbes

The Act of Congress authorizing the establishment of the United States Bureau of Mines became effective July 1, 1910. One of the most important duties Congress delegated to the Bureau in this Act was the study of health and safety conditions in the mineral industries. Early investigations of these conditions revealed the need of prompt Care of injured employees, as, under the difficulties inherent in their occupation, seemingly unimportant wounds if not treated promptly might become infected and cause permanent disability or even death. Many seriously injured persons brought out of mines and plants by fellow workers ignorant of approved methods of giving first aid or of safe means of transportation have been caused suffering and have had injuries accentuated to such a degree as to bring about permanent disability or death. The need of general instruction in first aid thus became apparent. BRIEF HISTORY OF FIRST-AID WORK The education of miners in the United States in first aid probably was conducted systematically first by the anthracite industry in Pennsylvania. Subsequently, first-aid training was carried on actively in Alabama and Indiana. Meanwhile, a general training campaign was carried on among industrial workers by the American Red Cross Society; when the Bureau of Mines began its nation-wide campaign of instructing employees of the mineral industries, the Red Cross turned over that part of its industrial training work to the Bureau but continued to cooperate by furnishing surgeons as judges in important first-aid contests and demonstr tions and assisted for a number of years in determining training methods.

Jan 1, 1937

By William J. Douglas

This document describes the development of a conventional mining equipment data base, and an approach for conducting industrial engineering studies of arbitrary mining systems employing network techniques. Data was acquired through underground time studies. Each member of a four-man field team was assigned to a specific machine during each shift for which observations were conducted. Using digital wrist watches and networks describing the man-machine interactions, all events occurring luring the course of each shift were recorded on cassette tapes. The tapes were transcribed, coded, keypunched, and validated using computerized editing techniques. The resulting data files were processed to provide statistics relating to activity durations and event frequencies. The results were used to evaluate operator, machine, and system performance for each section which was observed. Equipment, reliability, and maintainability analyses were conducted using the industrial engineering data files in conjunction with historical information collected at the mine site.

Jan 1, 1976