Search Documents

By J. W. van der Merwe, A. Palazzo

"Owing to the corrosiveness of the untreated brackish cooling water typically used for steel mills (and other environments), it is important to treat the water and monitor corrosion in such systems. Generally, corrosion rates are monitored with corrosion probes inserted into a pipeline or vessel. This has been standard practice for many years, and is widely accepted in industry. Typically, two kinds of probes are used - electrical resistance and linear polarization resistance (LPR) probes.In this study, the effectiveness and accuracy of the LPR technique was evaluated by comparing the electrochemical measurements with the results of mass loss tests using corrosion coupons. The corrosivity of the environment, a synthetic brackish water, was varied by varying the calcium hardness and alkalinity, and to simulate actual plant conditions temperatures of 35°C and 45°C were used. In addition to the corrosion rate measurements, the iron concentration was measured, as well as the imbalance from the probe.The corrosion rates obtained by LPR were from 57% lower to 385%higher than those from the immersion tests. Most probe measurements were higher than the immersion results, and 50% of the probe results were50% or more higher than the immersion results. The best correspondence between the two methods was obtained at low calcium levels, except for one measurement that was 93% higher than the coupon results. There was no clear correlation between parameters such as temperature and total alkalinity and the difference between the results. It would therefore appear that LPR measurements can differ significantly from immersion results, and LPR results should therefore be used with caution in industrial applications."

Jan 1, 2015

By J. Golamnejad

This paper attempts to model long-term production scheduling problems by chance constrained binary integer programming in a stochastic environment. This stochastic model is set up to account for ore block grade uncertainty. The probability distribution function of grade in each block is used as a stochastic input to the optimization model. This distribution function in each block should be determined using a Geostatistical Simulation approach. The deterministic equivalents of these chance constraints are then achieved, which are in the form of nonlinear in binary variables. A confidence level at which it is desired that the uncertain constraints holds, is specified in each scheduling period. Rather than the previous risk-based model, this formulation will yield schedules with a high chance of achieving planned production targets while maximizes the expectation of net present value and minimizing the variance function simultaneously. Using this method, the grade uncertainty is integrated explicitly into the optimization process.

Jan 1, 2006

The treatment of gold-plant tailings with ferrous sulphate to remove the cyanide is currently in use, on several gold plants. In some cases there is scope for optimization the process. The present work provides a detailed study of the reaction between cyanide and ferrous sulphate. Optimal conditions for the removal of total cyande required a ph of 5,.5 to 6,5 and an Fe:CN molar ratio of 0,5. Ferrocyanide ion is shown to be unstable In aqueous acidic solution, with rapid oxidation to ferricyanide, (Fe(CN) 6 ), and formation .of Fe(CN)5H2O3- at pH values below 4, The precipitate from the reaction between cyanide and ferrous sulphate consists mainly 01 Insoluble Prussian blue, Fe4[Fe(CNI&!.3,and IS shown to be unstable in the presence of alkaline solution, since it decomposes rapidly at pH values above 7 to form ferrocyanide, (Fe(CN)6 ), in solution and various insoluble iron oxides,

Jan 1, 1992

By C. Musingwini, M. Woodhall

An often overlooked factor in the analysis of mine layouts and schedules is technical operating flexibility, mainly due to its nebulous nature. If one glosses over technical operating flexibility the resultant mine layouts and schedules tend to be sub-optimal. The need to incorporate technical operating flexibility into the analysis and comparison of mine layouts and schedules is increasing in importance. This paper illustrates the nature of technical operating flexibility, reviews previous work on valuing operating flexibility and proposes how technical operating flexibility can be quantified for tabular reef mines by using a platinum reef deposit as a case study. Once technical operating flexibility is quantified it becomes possible to explore its incorporation into the analysis of mine layouts and schedules and subsequent optimization processes. The work described in this paper is part of a current PhD study at the University of the Witwatersrand. Keywords: mine plans, layouts, schedules, technical operating flexibility, ore availability.

By F. Bornman

Ore quality is declining, and the current spirals in mineral sands extraction is deemed inadequate to efficiently extract the valuable minerals. A new spiral was developed, the 117HM with the aim to extract the total heavy minerals in the order of 4.0% - 6.0% and the economic heavy minerals in the range 1.0% - 2.2% from the feed. An important measurable in the gravity concentration of mineral sands is recovery. Recovery measures how effectively the separator has extracted the valuable mineral contained in the input stream. The number of turns on the spiral trough influences the residence time of the feed slurry. A further optimisation followed with the development of the twelve-turn 117HM spiral. Four more turns were added for better recovery. The paper quantifies the effect of residence time on recovery.

Mar 30, 2026

By Tian Yingzhong, Guo XIN, Wei Peihe

The intention is to solve a series of problems in the flotation and desiliconisation of complex bauxite; aiming to achieve monomer dissociation of target minerals based on process mineralogy. According to the mineral surface, there are differences in physical and chemical properties and the molecular design theory of flotation agents. Designing the polar and non-polar groups of the bauxite flotation collector to make the reagent group easily combine with the mineral to form a cyclic chelate, will enhance the collection performance, and strengthen the drug selection performance. Developing a new type of positive flotation collector for bauxite with small dosage, strong selectivity and low foam volume. Keywords: Process mineralogy, monomer dissociation, molecular design, new positive flotation collector

Jan 1, 2020

Branch Minutes of the General Meeting held at President Steyn Gold Mine canteen on Wednesday, 10th May, 1978, at 4.00 p.m. Erratum We apologize to Mr J. G. Taylor for the error in one of his qualifications. Bio-engineering monograph The selection of papers presented at the International Bio-engineering Conference at the University of Cape Town organized by the South African Institution of Mechanical Engineers and held in April 1977, and which are appearing in The South African Mechanic al Engineer during April to June this year, will shortly be available in book form. Mathematics The Institute of Mathematics and Its Applications is planning the following conferences and symposia: The Nand F Proposals in Relation to Mathematics, 1st July, 1978: London School of Pharmacy. NIM reports Report no. 1917 The instrumental neutron-activation analysis of granites from the Bushveld Complex. (31st Mar., 1978.) Report no. 1951 Potentialities and limitations of four-parameter equations for the correlation of formation constants of metal-ion complexes in aqueous solution.(15th May, 1978.) Report no. 1963 An evaluation of the methods used at the National Institute for Metallurgy for the analysis of base-metal concentrates. (28th Apr., 1978.) Report no. 1964 The separation, by anion exchange, of noble metals on substituted cellulose. (28th Apr., 1978.) Guide To The Preparation Of Papers For Publication In The Journal Of The South African Institute Of Mining And Metallurgy The following notes have been compiled to assist authors in the preparation of papers for presentation to the Institute and for publication in the Journal.

Jan 1, 1978

By W. P. Nel

A fuel cell is an electrochemical engine that converts the chemical energy of a fuel, such as hydrogen, and an oxidant, such as oxygen, directly into electricity. The emerging fuel cell industry may represent a major opportunity for the global platinum mining industry. This is because low temperature fuel cell systems use platinum group metals as catalysts. Fuel cell vehicles may become the most important driver of future platinum demand within years of their commercialization. A great number of factors impact on and drive the diffusion of fuel cell vehicle innovation. Such drivers range from energy security to environmental concerns and the technological development of fuel cells and systems. Such factors and drivers of fuel cell vehicle diffusion are combined with the generic ?body of knowledge? on ?technology forecasting? and ?diffusion of innovation? to design a framework that provides a holistic approach to the analysis of this complex enterprise. An attempt is made in this paper to address the following questions: Which types of fuel cells require platinum group metals? Which types of fuel cells will achieve dominant design status? Will fuel cell vehicles diffuse successfully? How big will the impact of successful fuel cell vehicle diffusion be on future platinum demand? How well do fuel cell vehicles compete with incumbent technologies such as spark-ignited and compression-ignited internal combustion engine-driven vehicles? How soon will oil depletion start to drive the diffusion of fuel cell vehicles? How important is hydrogen as a fuel? What impact does the inadequate hydrogen fuelling infrastructure have on fuel cell vehicle diffusion? The paper contains some initial results of a research project that has the aim of producing a schedule of future platinum demand generated from fuel cell vehicles. Keywords: diffusion of fuel cell vehicles, technology forecasting, platinum demand forecasting.

Jan 1, 2004

By N. J. Roodt

Mine dumps created in terms of the pre-MPRDA regime (old order mine dumps) are currently not regulated by the MPRDA, and the common law owners of such dumps are free to process them without the need to obtain the relevant rights. The MPRDA Amendment Act purports to change this position. However, the wording of the Amendment Act raises a number of problems which render the post-amendment position at best unclear and at worst absurd and unworkable. The primary concern with the Amendment Act is that, on one interpretation, material placed on the same dump at different times may be treated differently at law. Thus, parts of a dump may be subject to one person?s right while others may be subject to another?s right. Moreover, case law has generally regarded mine dumps as movable property and, by extending the MPRDA to apply to all mine dumps, the Legislature is extending the ambit of the Act to cover movable property, a scenario not contemplated by the wording of the Act (even after its amendment) in relation to applications for rights. The better interpretation of the amendments, which are not yet in force, is that they will not apply retrospectively to old order mine dumps.

Jan 1, 2010

By M. S. Smith

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The condition of tunnels at Premier has deteriorated to such an extent that an objective viewpoint on what leads to poor condition was required. Poor and untimely development results in schedule deviation, rehabilitation, and increased working costs. The project focused primarily on quality, and not on efficiency. The project gave management guidelines that need to be focused on in order to produce quality infrastructure. The conclusions were reached by doing literature searches, underground site investigations, benchmarking and computer simulations. From the results we can see that, in order to produce good quality tunnels, we have to have the basics working. This was found to be one of the major problems. Firstly, tunnel profiles are not to the design specification and no fixed blast designs existed. After revising tunnel profile statistics, over break increased to 10% (previously 7%) and development metres were 50 m short of target. Blasting was not monitored and designs not optimized for the conditions. Furthermore, geological factors are the main contributor to tunnel failure, although this process is initiated and aided by poor development (overbroken tunnels, incorrect profiles, direction and location) and blast damage. Continuing to develop tunnels in the current manner will cost R 1.5 million in additional costs for loading and supporting overbreak, whilst an additional 1 800 man-shifts will be required. Blast patterns were designed as a starting point for trials, while the implementation of a blast management system, development statistical database, tunnel hand-over procedures and a revision of the bonus system were proposed.

Jan 1, 2004

By A. V. Rasskazova

Theoretical substantiation of leaching of clustered ultra-fine gold by the electro-photo activated cyanide and chloride solutions is given in the paper; and processes of activation of leach solution by electrolysis and photo-activation are described. Comparative experiments on electro-photo activated leaching of ultra-fine gold from refractory ores by cyanide and chloride solutions were carried out. The material for research is primary ore of the Pogromnoe deposit (Russian Federation, Trans-Baikal Territory). The ore is characterised by the minimum sulfide minerals and the organic carbon content. Gold in ores of this deposit is presented as mainly ultra-fine. Gold inclusions in quartz and silica-alumina minerals (metasomatic minerals) are ultra-fine. Sulfide minerals (2.5-3%) are presented in ore generally by pyrrhotine (gold content does not exceed 10 g/t). Standard cyanide technology provides 49.5% gold recovery. Photo-electro activated air saturated NaCN provides 69.9% gold recovery. Laboratory research of chloride-hypochlorite column leaching demonstrated that the electro-photo activated method provided 78.9 % gold recovery to pregnant leach solution. Chloride-hypochlorite photo-electro activated solution can provide higher level of gold recovery with shorter process duration (10 days) in comparison with cyanide (40 days). The final decision regarding the choice of leach solution has to be done on the basis of technical and economic calculations. Keywords: Ultra-fine gold, cluster chemical reactions, active clusters, leaching, electro-photo activation of leach solution

Jan 1, 2020

By L. A. Cornish, R. Süss, M. Sephton, N. B. Maledi, J. H. Potgieter, L. Chown

The gas turbine industry is faced with a challenge to improve the performance of engines, while simultaneously adhering to stringent environmental legislation. One way of addressing the problem is by further increasing the recipient working temperatures. Unfortunately, the use of nickel based superalloys (NBSAs) in the gas turbine industry has reached its limitations. Although coatings can be used for small increases, and air cooling is also incorporated by design, attention is towards developing stronger metallurgical materials having higher melting points, with acceptable creep and corrosion resistance. A series of ternary and quaternary Platinum-based superalloys were developed. Platinum was selected because of its higher melting points compared to nickel, similar fcc structure and better corrosion properties. Mechanical characterisation studies of Platinum-based superalloys alloys, which included oxidation, creep and hardness, demonstrated reasonable results, outperforming an oxide dispersed strengthening (ODS) Fe-based superalloy (PM2000) and a nickel based superalloy (MAR-M200). During any materials development where high temperatures are concerned, high strength is the primary property of interest. However, during the development of gas turbines, component life and reliability, which are influenced by temperature, need to be taken into consideration, and therefore creep as well as corrosion (both temperature dependant properties), are important. These properties become significant with increasing temperatures. With increasing demand for higher temperatures, it is becoming increasingly important to include hot corrosion properties of the alloy during the material selection process. A short description on hot corrosion and its degradation mechanisms are given in this paper. Coatings are currently dominating as the best practical solution to address temperature increases. This paper looks at benefits and shortcomings of coatings over Pt-based superalloys as candidates for applications under extreme conditions. Key words: Hot corrosion, Pt-based superalloys, Ni-based superalloys, Coatings

Jan 1, 2006

By L. Bam, R. Machaka, S. Chikosha, N. S. Muchavi

"Parts manufactured through power metallurgy (PM) typically contain pores that can be detrimental to the final mechanical properties. This paper explores the merits of 3D X-ray computed tomography over traditional microscopy for the characterization of the evolution of porosity in metal injection moulding (MIM) and direct powder rolling (DPR) products. 17-4 PH stainless steel (as-moulded, as-debound and sintered) dog-bone samples produced via MIM and Ti-HDH strips (as-rolled and sintered) produced via DPR and were analysed for porosity. 3D microfocus X-ray tomography (XCT) analysis on specimens from both processes revealed spatial variations in densities and the existence of characteristic moulding and roll compaction defects in agreement with traditional microscopic microstructural analysis. It was concluded that micro-focus XCT scanning can be used to study MIM and DPR parts for the characterization of the amount, position and distribution of porosity and other defects. However, the majority of the sub-micron sized pores could not be clearly resolved even at the highest possible instrument resolution. Higher-resolution scans such as nano-focus XCT could be utilized in order to fully study the porosity in MIM and DPR parts. IntroductionMetal injection moulding (MIM) is a novel process, which combines the advantages of powder metallurgy (PM) and plastic injection moulding. MIM has found widespread applications in the cost-effective production of high-sintered density small parts with complicated shapes and mechanical properties equivalent to those of wrought materials (German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013). There are four basic processing steps involved in MIM, namely; feedstock preparation, injection moulding, debinding and sintering. These steps are discussed in greater detail elsewhere (Machaka, Seerane and Chikwanda, 2014; German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013).Feedstock preparation involves mixing metal powder with a carefully selected composition of polymeric binder materials at a specific temperature. The feedstock is then granulated and injected into a predefined mould die with the desired shape. The part produced during the moulding step is referred to as a ‘green’ component. The green component typically contains no porosity since the spaces between adjacent powder particles are readily filled with the binder materials (German and Bose, 1977; Li, Li and Khalil, 2007). Debinding is the systemic removal of the binder components by chemical, catalytic, or/and thermal means while maintaining the shape of the component. The part produced after the debinding step is referred to as a ‘brown’ component. Debinding is known to be the source of porosity in brown components (Ji et al., 2001; Tsai and Cen, 1995). Finally, the brown debound part is sintered to full or nearfull density (Sotomayor, Varez and Levenfeld, 2010). The sintering step and associated densification closes up the majority of the pores. Sintered MIM parts are typically sintered to high density (95–99%) and retain an irreducible amount of residual porosity (Barriere, Liu and Gelin, 2003; German, 1990)."

Jan 1, 2016

By Mauri Kauppi, Pekka Niemelä

World HCFeCr production is 6.0 million tonnes. Correspondingly 1.1-1.6 t slag / t FeCr is produced depending on the raw material basis. Essentially all FeCr is produced in submerged arc furnaces, while the role of competitive technologies like DC is limited. In all furnaces fluxes are used to optimize the slag composition. Vital characteristics are smelting point, electric conductivity and viscosity. The main components of FeCr slag are SiO2, Al2O3 and MgO. Additionally it consists of Cr-, Fe-oxides and CaO. Granulated slag and/or classified slag products are produced depending on the production process. The slag products are mainly marketed in road and civil construction purposes but also in producing refractories. Normally crushed and screened slags are produced simultaneously when recovering alloy. The leachate of slag products is low and performance results are excellent. Slag products successfully replace natural sand and macadam. Generation of waste is essentially reduced. Producing and using slag products are described as BAT-technology and it is an essential environmental aspect. Outokumpu Tornio Works produces 320 000 t FeCr-slag/a. This paper deals with formation of slag in smelting process, its chemical composition, physical and structural characteristics, utilization and product specifications as well as environmental aspects. The slag products are standardized and CE marked. Additionally the role of slag in smelting and alloy recovery is reviewed in this paper.

Jan 1, 2007

The 114th Annual General Meeting of The Southern African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Thursday, 11 August 2011. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, and also to recipients of awards, senior members of industry, Honorary Life Fellows, past-presidents, our members and other guests, among them the following: F. Cawood, President, Institute of Mine Surveyors of South Africa C. Roode, President, Mine Metallurgical Managers' Association of South Africa M. Cresswell, Chairman, South African Coal Processing Society A. Hay, Immediate Past President, South African Institute of Electrical Engineers L. Gardner, President, South African National Institute of Rock Engineers J. Krynauw, President, The Geological Society of South Africa (GSSA)

Jan 1, 2011

By S. E. Olsen, K. Tang

Slag-metal and slag-metal-gas heterogeneous equilibria involving MnO-containing slags have been simulated using recently developed Mn-based alloy and IRSID oxide thermochemical databases. A large number of experimental equilibrium data have been used to verify the calculation results. The experimental slag-metal and slag-metal-gas equilibria in MnO-SiO2binary, MnO-SiO2-CaO and MnO-SiO2-Al2O3ternary, MnO-SiO2-CaO-Al2O3quaternary andMnO-SiO2-CaO-Al2O3-MgO higher-order system can be reproduced within experimental uncertainties. The influence of temperature, CO partial pressure and slag chemistry on the Mn-and Si-distribution equilibria have been quantitatively evaluated. This leads to a sound basis for optimizing the manganese ferroalloy production processes. Key words: MnO-containing slag, manganese ferroalloy, equilibrium simulation, thermochemical database

Jan 1, 2004

By D. M. MacHunter, T. Lawson, D. K. Henderson

The development and commercialization of new generation high tension electrostatic separators has provided a basis for simplifying mineral separation plant circuitry. The inclusion of new design features including insulated plate electrodes that have resulted insignificantly improved separation efficiencies in electrostatic separators are described. The increase in separation efficiency has resulted in a reduction in the number of treatment stages required to produce final high grade mineral products. Comparative performance data on different feed types are presented. A comparison between mineral separation plant flowsheets using both conventional and new generation high tension electrostatic separation technology is presented. A 55% reduction in the number of installed electrostatic separators and a 36% reduction in plant area was achieved through the use of this new electrostatic separation technology.

Jan 1, 2003

By B. Zongwane, A. T. Visser

In surface mining operations, ultra-heavy trucks operate on haul road networks which are typically from 10–40 km in length. Road networks for these vehicles have historically been designed and maintained empirically, relying heavily on local experience. Whilst it is possible to construct amine haul road that requires no maintenance over its service life, this would be prohibitively expensive, as would the converse but rather in terms of vehicle operating and maintenance costs. An optimal functional design will include a certain amount and frequency of road maintenance which can be planned, scheduled and optimized within the limits of required road performance and minimum vehicle operating and road maintenance costs. For existing mine haul road networks, which may not be optimally designed and maintained, the problem of identifying existing deficiencies, quantifying their impact and assigning priorities within the constraints imposed by limited capital equipment and manpower is problematic. This is reflected in the fact that most surface mine operators agree good roads are desirable, but find it difficult to translate this into an effective road maintenance system. The aim of this paper is to present a road maintenance management system which utilizes on-board truck diagnostic data in conjunction with computer-based truck dispatch systems. Through a comparative analysis of the various haul road maintenance systems available to a mine, a condition-triggered road maintenance system is introduced. System architecture, evaluation of real-time data, event trigger level determination, specific condition signatures and real-time rolling resistance calculation are discussed. Finally the event, activity, transaction and notification system is portrayed in conjunction with the determination of key productivity indicators and benchmarked road and truck performance. Keywords: Haul road, maintenance, surface mining, rolling resistance, truck haulage.

Sep 1, 2001

By T. A. Claasen

Exceptionally low yields in the coking-coal fields of the Soutpansberg area in the northern Transvaal, are taxing the skill and ingenuity of preparation engineers. The coals are highly intergrown, and a series of crushing and washing steps may be required to extract the maximum usable tonnage. In addition, novel preparation techniques may have to be employed. This paper, which is a case study of work recently undertaken, gives a general account of raw coal properties, emphasizing those related to maximum recoveries, and outlines the steps involved in the design of appropriate flow sheets based on laboratory studies.

Jan 1, 1980

By H. H. Einstein

This paper reviews how uncertainty has been dealt with over the past 40 years using the decision making cycle as a frame of reference. The review of the phases of this cycle, as applied to rockmechanics and rock engineering, namely characterization, performance analysis, updating and decision making shows that in each, progress has been made over the past 40 years, although most of the basic concepts existed already in the 1960’s. Characterization is the area in which the greatest scientific steps were taken, this phase and performance analysis also gained from the tremendously expanded computational capabilities which allow one to use both more complex and more practically oriented models. The greatest practical advance is without using any doubt in risk based decision making although its acceptance shows interesting differences between different professions. Dans l’article suivant on utilise le cycle de décision pour illustrer le développement du traitement des incertitudes en mécanique des roches et en construction en roche dans les quarante années passées. La revue des phases du cycle de décision montre qu’on a fait du progrès dans chaque phase du cycle de décision, c’est à dire dans la caractérisation, dans l’analyse et la prédiction du comportement, dans l’actualisation et dans l’acte de décision, même si les concepts fondamentaux existaient déjà dans les années 1960. Les plus grands avancements scientifiques se trouvent dans le domaine de la caractérisation tandis que l’analyse prédictive profitait du développement de l’informatique qui a mené à des modèles plus complexes mais aussi plus pratiques. Le plus grand progrès est sans doute dans le domaine de l’acte de décision sur la base des risques. Ce procédé est devenu assez commun même s’il y a encore des différences d’acceptation entre différentes professions. Im vorliegenden Artikel wird der Entscheidungszyklus gebraucht, um darzustellen wie sich derUmgang mit Unsicherheiten im Felsbau während der letzen 40 Jahre entwickelt hat. DerÜberblick über die Phasen des Entscheidungsprozesses zeigt, dass bei der Anwendung in derFelsmechanik und im Felsbau, in allen Phasen d.h. bei der Charakterisierung, bei der analytischenVorhersage, beim Aktualisieren und bei der Entscheidungsfindung Fortschritte gemacht wurden,obwohl die grundlegenden Konzepte bereits in den 1960er Jahren existierten. Im Gebiet derCharakterisierung gab es wohl die grössten wissenschaftlichen Entwicklungen, während dieanalytische Vorhersage vor allem von den Fortschritten der Informatik profitierte, welchekomplexere wie auch praktischere Modelle möglich machte. Der grösste Fortschritt ist ganz sicherin der Entscheidungsfindung zu beobachten, wo Risikobetrachtungen gang und gäbe sind, obwohlhier noch einige Unterschiede zwischen verschiedenen Berufsgattungen zu finden sind.

Jan 1, 2003