Search Documents

By J. F. Morrison, C. H. Wyndham, N. B. Strydom

INTRODUCTION The shovelling of rock in stopes is still a basic and important operation in many gold mines in the removal of gold-bearing rock from the stopes. There is, however, little factual knowledge of the factors which influence the the rates of energy expenditure and work output, and of the way in which variations in these factors, individually or in combination, affect the mechanical efficiency of the mine workers. What for example is the influence of different rates of shovelling, shovel loads and distances of throw? How does stope width and dip of the stope affect the mechanical efficiency of men shovelling rock? Recently a simple physiological test was introduced into the gold mining industry for classifying Bantu recruits into those capable of hard, moderate and light work. If this test is used to select only those Bantu mine workers who are capable of hard work for the task of shovelling rock in stopes then the rate of energy expenditure which could be expected from these men is 1.5 litres/min for the entire period of the shift. With an adequate knowledge of the influence of the various factors which affect the rate of energy expenditure of men shovelling rock in stopes it would be possible to set work standards for Bantu mine workers in stopes. This should be done in terms of the rate of shovelling, the shovel load and the distance of throw for any combination of width of stope, dip of stope, condition of foot wall and grade of rock in such a way that the resultant energy expenditure would be the 'optimum' that could be expected from the men but would be within their capacities for physical work of an endurance nature (that is, 1. 5 litres/min from the 'average' Bantu mine worker). Work standards could thereby be determined for the different stopes of a mine on a sound and systematic basis. In order to supply the information required a study was carried out by the Human Sciences Laboratory in which the work output and energy expenditures (in terms of oxygen consumption in litres/min) were measured on six highly trained Bantu mine workers under the following conditions: (a) rates of shovelling of 3, 4, 5, 6, and 10 shovels per minute. (b) loads of from 9 to 18 lb on the shovel. (c) distances of throw from 8 to 20 ft. (d) stope width of 28 in., 42 in. and 72 in. (e) dip of stopes of 0°, 15° and 30°. (f) rough and smooth footwalls and various grades of rock size. This paper gives the main results of practical importance of this study. Method The experiments were designed and conducted in conjunction with the Work Study Department of one certain underground conditions such as variable stope widths, stope angle, etc., were made available in a mine Surface Training School and suitable subjects were selected from the large number of labourers being put through the training school. Subjects Bantu recruits who had returned to the mine for a new contract and who had previous underground experience on shovelling were considered to be suitable as subjects for the experiments. The particulars of the subjects are given in Table I. TABLE I PHYSICAL CHARACTERISTICS OF SUBJECTS Weight Height Surface area Max O2 capacity Subject (Kg) (cm) (sq meters) (Litre/minute) A 71.5 167.3 1.80 3.5 B 61.5 162.3 1.65 2.8 C 63.0 164.1 1.69 2.4 D 66.5 167.4 1.75 2.8 E 70.2 164.6 1.77 3.0 F 77.8 173.1 1.92 3.8 Training The method of shovelling, accepted by the Work Study Department, was demonstrated to the subjects who then practised the movements with empty shovels, under the supervision of an instructor. After the technique was mastered, the men started shovelling rock and were trained for at least four hours per day to work at the higher shovelling rates. Training was continued for three weeks to enable the subjects to achieve a reasonable degree of physical training and conditioning. Shovelling method In both the kneeling and standing positions the subjects faced the pile of rock, grasped the shovel in the accepted manner and pushed the blade of the shovel into the base of the pile of rock, sliding the blade between the rock and the concrete floor. In the standing position (72 in. wide stope) the back leg assisted in the movement by pushing the knee against the back of the hand holding the shovel handle. In the kneeling position the elbow was tucked into the side of the body so that the muscles of

By D. S. Dihalu

A generalization of Gy?s model for the fundamental sampling error introduced the new ?parameter for the dependent selection of particles?, denoted as Cij. This allows for modeling deviations from the ideal situation where the selection of a pair of particles is composed of two independent selections. The generalized model potentially leads to more accurate variance estimates in the case of clustering of particles, differences in densities or sizes of the particles or repulsive inter-particle forces. A straightforward and practically applicable method is needed for the determination of this parameter for miscellaneous mixtures in industrial settings. In this contribution, the feasibility of using digital image analysis to determine this parameter Cij, will be demonstrated. Line transect sampling of a digital image was used to construct a transition probability matrix. A new algorithm to derive quantitative estimates for Cij will be presented and discussed. The applicability was verified by a photograph of zirconium silicate particles of sizes typical for industries dealing with pharmaceutical, food/feed, and environmental applications. Conditions affecting the practical applicability are identified and potential pitfalls will be discussed, including e.g. how a potential unrepresentative surface can affect the quality of the estimate of Cij.

Jan 1, 2010

By B. Samanta

This paper investigates the performance of the neural network technique in a placer deposit situated at the Nome district in Alaska. Initially a single neural network model was constructed to estimate the gold grade. However, at a later stage, an ensemble model consisting of multiple networks was also constructed via the Adaboost algorithm. The reason behind the use of the ensemble model of the Adaboost algorithm was to examine if the ensemble model provided superior performance to the single neural network. As indicated by other studies, Adaboost did not have a better performance than a single neural network in this specific application. This may be due to the high noise inherent in the gold data used in this project. Consequently R2 values of gold prediction are also poor for both the single and multiple networks.

Jan 1, 2005

By RT White

For many years the concept of life cycle costing (LCC) was promoted for decision making in corrosion protection systems. Nevertheless, the application of LCC was limited. Input data was often sourced from suppliers and met with scepticism. As a result final analysis was often insufficiently rigorous to meet the needs of Project Managers in sound decision making. The need for expediency often resulted in non-optimal corrosion protection system specifications. With improved communications and the global reach of industries, case history data, based upon actual performance has been able to provide input to substantiate decision making. However, today?s focus upon sustainability whereby environmental, economic and even social aspects enter into decision making has extended LCC into Life Cost Analysis (LCA). In an LCA analysis energy and environmental inputs into systems are compared as part of an overall assessment. The development of Agenda 21 at the Rio summit of 1992 has challenged the countries of the world to look at sustainable development in every economic activity. This ranges from construction to mining to electricity production to automotive production, use and disposal. The protection of buildings, infrastructure and transport systems is part of the needs of sustainable development. Zinc based corrosion protection has been an important part of the arsenal of the corrosion protection industry. This paper will highlight the use of LCC and the development of LCA with reference to the use of zinc based protection systems in a number of important industries.

Jan 1, 2006

By W. I. van Drunick

AngloGold Ashanti Metallurgy has recently been involved in the successful installation of intelligent, expert control systems on the milling circuits. The benefits of expert systems in these highly interactive circuits are obvious. Existing comminution tools, which have been developed and can now be incorporated into online control, include improved modelling techniques and understanding, robust and competent simulation methods, sampling techniques, and optimization methods. The minerals processing industry has seen the benefits of predominantly research-based centres turning their focus to commercial applications of comminution circuit modelling packages, which in turn can be utilized within expert control systems. Expert mill control has been successfully installed at AngloGold Ashanti South Africa?s Mponeng and Kopanang Gold Plants. Expert control has also been installed at AngloGold Ashanti?s West African Sadiola Mine operation. The implementation of the systems has produced a number of positive outcomes. Plant surveys usually result in the identification of sub-optimal areas, and the control philosophy is then configured to ensure that these areas (along with the entire circuit) are optimized and maintained. Outdated PID loops have generally resulted in oscillatory control with large amplitude deviations from set-point. Significant improvements in SAR Metallurgy operations have been realized, firstly through achieving stability in the load and cyclone control, and secondly through online identification and implementation of optimized set-point conditions for mill mass, discharge density, etc. Soft sensors are configured to accurately estimate parameters that were historically not measurable, viz. breakage rate, mill load condition, onlinekWh/t-75 microns, mill discharge density and cyclone overflow grading. The Mponeng Plant system achieved circuit stability and improved overall grind. The Plant was able to pay back the control installation after 3 months, based on the additional recovery obtained from the finer grind. The system at Kopanang Plant has also resulted in enhanced plant recovery as a result of a finer grind and a lower residue gold content. The payback for this system was calculated at approximately 6 months. AngloGold Ashanti Metallurgy is currently expanding the installation of expert control to its other operations. It is also evaluating the performance of various suppliers of advanced control systems.

Jan 1, 2005

By R. Minnitt, C. Morgan, D. Fourie

The problems associated with outliers and their adverse effects on resource estimation in deep level South African gold mines are presented, and solutions suggested in available literature are reviewed. Traditional Witwatersrand type outlier capping uses the 99th percentile grade as the upper limit, a somewhat blunt approach. The occurrence of high and low grade areas in mining operations and the estimation of resources using geostatistical techniques require that the assumption of stationarity be upheld. Honouring the stationarity of data requires that mining areas be subdivided into appropriately sized and spaced domains. In order to overcome high-grade conditionally biased block estimates, the overly strong influence of extreme grades is mitigated by using naturally occurring grade sub-domains, by identifying outliers within the grade sub-domains, allocating relevant capping limits, and weighting them in a post-estimation process to. Rather than applying a capping value across a domain it applies a maximum cap based on the extreme value and its range of influence; the method also ensures that relevant capping occurs even in lower grade sub-domains. The proposed method for capping outliers recognises that metal contained in high grade chip samples should not be over-capped, and based on the grade of surrounding samples. The post-processing method of capping outliers does not interfere with the kriging equations. The method is simple, elegant, and can be easily applied. An advantage is that the output from the kriging process is not overwritten, allowing for comparison between original kriging results and post-processing results.

Sep 1, 2021

By M. A. van Nierop

The Discrete Element Method (DEM) is a model that is used to simulate the motion of the media in a grinding mill. The sum of the energy that is lost in inter-media and media-wall collisions represents the power drawn by the mill. The fact that the DEM predicts the power drawn by grinding mills over a large range of diameters has been used to show the validity of the DEM. However, the power drawn by a mill is a function only of the sum of forces of the load on the shell liners. A more accurate and detailed validation of the DEM would be to measure these forces as a function of angular position as the liner moves under the load, and to compare these measurements with predictions generated using the DEM. An experimental mill has been developed to reproduce exactly what the 2-dimensional DEM simulates. The 0,55 m diameter mill has a length of 0,023 m, which is fractionally larger than the diameter of the media used in the mill. One of the lifters in the mill has been instrumented so that the forces on the lifter can be measured as the mill rotates. The DEM simulation will be used to predict these forces. This will give experimental evidence of the validity of the DEM for modelling load behaviour in rotating grinding mills.

Jan 1, 1999

By G. C. S. Burns

"A system has been developed to simulate the mining of the Mufulira orebody. The main output from the system is a picture-gram from which the start date and effective life of all proposed mining faces can be measured. This information provides schedule dates for the completion of major capital development projects and stope preparation activities.The orebody must be divided horizontally into main levels and vertically into blocks of equal interval. Ore reserves are defined by specifying the tonnage contained in each block and main level. Mining faces are defined by their co-ordinates, and may themselves be split into sublevels. The simulation maintains an echelon between contiguous sublevels. Other face parameters control the speed of mining, the availability and relative priority of the face.The required production from each crusher/shaft system is specified. The technique of simulating the mining process in order to achieve the required production is described."

Jan 1, 2014

By C. Steve

ABSTRACT: In this paper, the stability evaluation and bifurcation criteria are presented for the Jinping arch dam structure. The bifurcation models in failure status of the arch dam are derived from the uniqueness of the controlling equation of dam behaviours, and the relative phenomena between positive definition of dam structural tangent stiffness and bifurcation are given in the paper. Then the structural collapse criteria for arch dam are discussed based on the energy mode. A stability criterion of dam based on the connection of yield zones is proposed according to the implementation of elasto-plastic FEM (finite element method) numerical analysis. In accordance with this judging method, nonlinear FEM analysis is used for Jinping arch dam. The failure process of the Jinping dam was simulated and yield zones were found under the overloading condition. Keywords: Stability evaluation, bifurcation, failure process, Jinping arch dam ZUSAMMENFASSUNG: In der Verliegenden Arbeit wird ein integrater geomechanisch Modellversuch fuer Jinping Bogenstaumauer Vorgesstellt. Die Bogenstaumauer liegt aut der komplizerten felsformationen. Der Zerstoerungsmechanismus, die Stabilitaetsfaktoren und die Interaktion zwischen der Bogenstaumauer und den Seiltichen. In der Vorliegenden Arbeit wird eine dreidimensionale finite element analyse fuer die seitlichen. Gestein sauflager mittels dem Bruchmodell Vorgestellt, da fuer Jiniping Bogenstaumauer angewandet wird. Ein Bruch mechanismus model einschliesslich der statistischen parameter der Gesteinfes tigkeit wird entauckeit. RÉSUMÉ: Das ce documènt a été faite une analyse d’elemt limité de trois dimensions dn fondement de construction de roche faisant appel au modéle de l’endommagemnet à fracture, analyse appliquée an fondement du bar ragevoute de Jinping. Ce documènt décrit le test de modéle géomecanique intégral pour le barrage-voûte de Jinping L’ampleur du modéle en question constitute l’une de plus importantes en China. Ils correspondent par faitement anx calculs des résultats.

Jan 1, 2003

By K. Osburn

South Deep Gold Mine, owned by Gold Fields Ltd., is situated near Westonaria in the Gauteng Province of South Africa and mines the conglomerate bands of the Upper Elsburg reefs (Mondeor Conglomerate Formation) of the Witwatersrand Supergroup and the Ventersdorp Contact Reef (VCR) of the Ventersdorp Supergroup. The stoping and underground developments are mechanized. The Upper Elsburg reefs are mined by a variety of mining methods, including mechanized drift and fill, modified drift and bench, longhole stoping, and low-profile mining. Optimal mine design and scheduling for deep-level mechanized mining are complex, and success is highly dependent on detailed, robust, and accurate geological and geostatistical models. Geological structures significantly influence the sedimentological characteristics, distribution, and preservation of the Upper Elsburg reefs and VCR. Accordingly, particular emphasis is placed on the generation of a mine-scale structural model that accommodates the relationships between the older north-trending fault systems (West Rand and Panvlakte faults) and younger east-trending dextral wrench faults. Results from underground mapping, borehole intersections, and highresolution three-dimensional seismic data have been integrated to produce coherent three-dimensional geological models. The Upper Elsburg reefs suboutcrop against the VCR and comprise an easterly diverging clastic wedge, thickening from the suboutcrop position, to approximately 130 m at the mine?s eastern boundary. The Upper Elsburg reefs are characterized by conglomerate and quartzite bands forming multiple, stacked, upward-fining unconformity-bounded couplets. Palaeocurrent directions are dominantly from west-northwest to east-southeast, indicating that the more proximal deposits are preserved close to the suboutcrop, with distal facies to the east. Sedimentological modelling is applied to individual stratigraphic units and caters for facies definition. This is achieved through channel width (CW) kriging and fitting of type sections to borehole and mapping data. Homogenous geological geozones for each stratigraphic unit are thus defined within individual structural blocks on the basis of those sedimentological parameters that have been found to have a positive spatial correlation to gold concentration. These geozones then serve as constraints to the evaluation of the orebody. This contribution presents a summary of the modelling processes that are currently applied in the development of high-confidence, timeously produced geological models that are essential input for mineral resource estimation and mechanized mine planning and scheduling.

Jan 1, 2014

By F. M. L. Mulaudzi

Behaviour studies of metal dusting processes and associated filamentous carbon formation were undertaken on Alloys 600, 601, and 800 using a simulated metal dusting environment of 25C0-70H2-5H20 (vol.%) at 650°C. These samples were studied visually and by optical microscopy, scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM-EDX) and x-ray diffraction (XRD). Visual examination and SEM surface observation showed that Alloy 800 suffered metal dusting attack at an early exposure reaction period. The coke deposit amounts increased significantly with reaction time from 168 hours to 336 hours in Alloys 600, 601, and 800. Alloy 800 showed pitting after 168 hours' exposure, and the degree of pitting increased after 336 hours. XRD showed all these alloys had a common austenitic phase, with Alloy 800 also having ferritic metal particles. Alloy 800 after 168 hours' exposure had a complex phase mixture on the surface, consisting of ferritic Fe and austenitic FeNi phases. For coke deposit, there were also Fe304, Fe3C and graphitic carbon. The existence of Fe, Ni, and Cr metal particles, and also graphitic carbon in coke deposits, was confirmed by EDX analyses.

Jan 1, 2013

Contribution by W.D. Ortlepp In the Journal of May 1994, the authors first presented the concept and analysis that formed the basis for a design approach for deep tunnels, now expressed more explicitly in the present paper (March/April 1996). In a contribution in the Journal of March/April 1995, I expressed a certain disquiet about the validity of their original approach. The authors responded to these criticisms in the same issue. It is apparent to me now that both the contribution and its rebuttals were written, probably for different reasons, in such an obscure and pedantic way as to further confuse the reader rather than provide enlightenment. My concern still persists. But in order to avoid further confusion I will attempt to pose my uncertainties and difficulties in a much more direct way. On page 98 (top of 2nd column) in the earlier paper, an important statement concluded as follows: '. . . the horizontal ellipse requires 140 per cent less force for equivalent stability'.

Jan 1, 1996

By X. Xiang, W. Xia, J. Yin

"TiCl4 slurry containing valuable metals is an unavoidable by-product of the titanium ore chlorination process. The recovery of these valuable metals, which include titanium, niobium, tantalum, and aluminum, is an urgent issue to tackle in the titanium industry. The results of this investigation show that the valuable metallic elements can be recovered from the slurry by evaporation in a sealed container and leaching with dilute hydrochloric acid. After evaporation at 200°C for 60 minutes, nearly 99% of the titanium was recovered in the form of TiCl4, which was formed by the reaction of the TiO2 in the slurry with AlCl3. After evaporation, metals like niobium, aluminum, and tantalum remained in the residue. By leaching with 2.1 mol/L HCl at a L/S ratio of 6:1 mL/g at 80°C for 60 minutes, the soluble metals, such as aluminum, iron, and copper were all removed from the residue, and the niobium and tantalum were further enriched in the leach residue. A concentrate containing 53.40 wt% Nb and 5.57 wt% Ta was obtained by washing the leach residue with dilute aqueous ammonia under stirring. A potential waste water purifying agent containing 263.75 g/L AlCl3 was produced by purifying the leaching solution with Al(OH)3 and modified polyacrylamide. IntrodutionTitanium tetrachloride (TiCl4) is an important intermediate in titanium metallurgy that is widely used in the production of titania and titanium sponge (Akhtar, Xiong, and Pratsinis, 1991). In conventional titanium metallurgical processes, high-titanium materials such as synthetic rutile and high-titanium slag are reacted with chlorine to produce TiCl4 in a fluidized-bed furnace. Accompanying elements, such as Al, Nb, and Fe also react with chlorine to form chlorides, which are mixed with gaseous TiCl4 (Anderson, 1917). In the condensation process, gaseous TiCl4 is refrigerated and high-boiling-point chlorides are precipitated in the liquid TiCl4 to form a slurry containing 50~60 wt% TiCl4 (Wang, Xiang, and Wang, 2012).Various methods have been proposed to recover TiCl4 from the slurry, including microwave heating and spray drying (Wang, Xiang, and Wang, 2012, Wang et al., 2010a). To date, the only way to recover the TiCl4 is to return the slurry to the fluidized-bed furnace. However, this causes fluctuations in the temperature in the furnace, resulting in incomplete reaction between titanium-rich materials and chlorine. Therefore, the slurry is often rinsed with water and neutralized by adding lime, which caused serious environmental pollution and wastes a valuable resource (Roy, Bhatt, and Rajagopal, 2003)."

May 1, 2019

By H. Copur

Experimental studies for quantification of force and brittleness indices relevant to rock cutting performance are presented. A simple interpretation method is developed, which quantifies the force-penetration response obtained from indentation tests. Basic parameters of the quantification are force increment and decrementrates, force increment and decrement periods, and number of increment and decrement data points. Blocks of eleven different rock samples were collected from different operating mines in Turkey and subjected to indentation tests to calculate the indices. The samples included harzburgite, serpentinite, trona, limestone, claystone, two different sandstone samples, siltstone and three different chromite ore samples. The concept was validated by a set of full-scale linear cutting tests using a conical cutter for measuring the cutting performance in relieved and unrelieved conditions, i.e. cutter forces, specific energy, size distribution of rock cuttings. The rock cuttings were sieved to determine coarseness index, indicates coarse chip generation characteristics, and size distribution. The force index is moderately correlated with the cutting performance and mechanical properties of the rocks, and poorly correlated with the coarseness index and size distribution of cuttings. A general and moderate trend is observed between the brittleness index and the coarseness index, cutting performance for unrelieved cutting conditions and mechanical properties of the rocks. However, additional data is required to fill the data gaps and to potentially establish relationship between the brittleness index and all other parameters.

Jan 1, 2003

By G. M. Dowo

The widespread environmental damage caused by slimes dam construction requires rehabilitation as one of the key management strategies towards land restoration. From the time when Mhangura Copper Mine in Zimbabwe was shut down in 2000 due to viability problems, no follow-up studies were carried out on the slimes dams to assess their development with respect to ecosystem function and longterm recovery. The ecosystem function analysis (EFA) method was thus employed to achieve this end. EFA is a monitoring procedure that establishes how well an ecosystem functions as a biophysical system through the use of rapidly assessed field indicators. The field procedure makes use of simple visual indicators that are related to various soil surface processes. Conventional sampling methods are used to collect the vegetation data. The data was first analysed using landscape function analysis (LFA) software packages and then with various multivariate statistical techniques. In total 27 species were recorded from 14 families; 21 of them occurring in the acacia woodland and only 8 on the slimes dams. Hyparrhenia sp. was the dominant grass on Dam 5 and Imperata cylindrica dominated Dam 6. Acacia saligna was the most abundant tree species on the dams. The tree layer on the slimes dams was not as developed as the grass layer. The rehabilitated slimes dams converged with the natural woodland for the LFA indices of stability, nutrient cycling, and infiltration, which suggested a high level of functionality. The main factors affecting the sustainability of the rehabilitation are postulated to be fire, grazing, and tree harvesting. The study contributed to the importance of, and methods used for, assessing ecosystem function on rehabilitated slimes dams in Zimbabwe, which are often ignored as most efforts focus on the establishment of vegetation on the dams. Keywords ecosystem function analysis, EFA, mine tailings, rehabilitation, monitoring, Mhangura Copper Mine, ecosystem function.

Dec 1, 2013

By M. Kahn

This paper traces the rise of South Africa's mining industry in the context of the different state forms that oversaw its development. It commences with the mining-led industrial revolution through four periods of conflict, each of which contributed to a deepening of the industrial base, with constant battles between domestic and foreign capital and labour, and the rise of both Afrikaner and African nationalism. The role of state-owned enterprises has been crucial in shaping this dynamic so that at its peak the public sector and leading mining houses constituted two massive centres of power. This was followed by a thirty-year period of neo-liberal experimentation. The current debate on the 'developmental state' is an attempt to reconstruct the state as a counterweight to capital. It is argued that while the country has moved toward inclusive political and economic institutions, these are both limited by deep 'extractive' characteristics. This transformation failure provides a fertile ground for populism that presents one of the biggest threats to inclusive growth. Cited examples point to the many ways that states have sought to deal with the bonanza that conversion of mineral non-resources into resources brings. Such greenfield resources on state land, or in areas where the state holds monopoly rights, do not present ownership issues. It is suggested that this is the route that South Africa should follow, as the alternative will be conflictual.

Jan 1, 2013

By C. J. Tonkin

Compressed air is widely used on South African gold mines. However, due to recent and proposed future electricity tariff increases it is quickly becoming too expensive to produce and use. Boxfront chute systems at ore passes were focused on during this study, and a number of alternative power sources were examined. After comparing primarily costs, and secondarily safety and practicality, of a number of systems based on water and hydraulic oil, a system making use of either air or water was determined to be the most cost effective. A payback time of 8 years was calculated, which will be significantly less taking into account the avoidance of failures due to electricity and water shortages, which would not affect this system due to its ability to swap between either air or water. It was recommended that this system be installed at all boxfront chutes as soon as possible so that the company can begin to benefit from the cost savings.

Jan 1, 2013

By N. Sano

The chromium oxide in stainless steel slags usually exists as Cr2O3. However, there is a possibility that it is oxidized to hazardous CrO3 after disposal or during use. Therefore, some technical developments to reduce chromium oxide by using a smelting reduction technique have been reported recently. This paper describes the fundamentals of the technique which have been applied to ferrochromium production and reviews the recent results in literature.

Jan 1, 2004

By A. M. Milev

A stand-alone instrument especially designed for recording strong ground motions was used in this study to create a large data base of peak particle velocities measured on stope hangingwalls. A total number of 58 sites located in stopes mining the Carbon Leader Reef, Ventersdorp Contact Reef, Vaal Reef and Basal Reef were monitored. The peak particle velocities were measured at the surface of the excavations to identify the effect of the free surface and the fractures surrounding the underground mining. From the monitoring results obtained, the velocity criterion of 3 m/s will bean adequate value that support systems have to sustain during a rockburst in most cases. However, PPVs in excess of this criterion were recorded, and some PVDs were damaged or irretrieveable, a consequence of which was that possible extreme events were not recorded. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response, defined as the ratio of the measured peak ground velocity to the peak ground velocity inferred from the mine seismic data. The site response measured at all mines studied was found to be 9 ±3 times on average. Values of the site response did not vary significantly with seismological parameters such as peak ground velocity, hypocentral distance and source radius.

Jan 1, 2005

By C. Musingwini

In the past ten to fifteen years, many organizations have applied business process re-engineering (BPR) to significantly improve their business competitiveness or stave off closures. The mining industry in Southern Africa is no exception and documented examples can be drawn from South Africa. Although the concept is superficially simple, its application has been marked by a high failure rate of about 70 per cent because it has been generally misunderstood. Shabanie mine, a chrysotile asbestos fibre producer in Zimbabwe took cognisance of this fact by cautiously embarking on a modular BPR programme in October of 2002. A year was used as a complete cycle or module for re-evaluation of the programme. Shabanie mine adopted BPR as part of management efforts to remain competitive amid serious threats to operational viability. These threats included hyper-inflation driven rising production costs, a declining world asbestos market and a possibility that Russia could take over the shrinking world asbestos market by dumping low-priced asbestos fibre. The only competitive advantage that the mine had was the high quality of its long-fibre chrysotile asbestos. The major BPR thrust was therefore to redesign processes for improved productivity and ultimately achieve a lower cost per ton of final asbestos fibre product. In addition, corporate culture change and cost-saving were also factored into the programme. This paper discusses the implementation experience of the BPR programme at the mine. The main BPR beneficial highlights are improved productivity, sizeable cost-savings, positive corporate culture change and identification of secondary projects. One of the lessons learnt from this programme is that mining companies will have to deal with the HIV/AIDS pandemic if they are to sustain high levels of productivity into the future.

Jan 1, 2005