Search Documents

By K. Kabezya

A study on slag dispersion in a model of bottom-blown bath smelting converter was undertaken at room temperature. The aim was to investigate the behaviour of the dispersed slag phase at various operating conditions with very high gas flow rates in low slag volume (10%) systems. For simulation purposes water, paraffin-oil, and air were used to represent the bulk steel, molten slag, and gases respectively in a one-fifth cold model of the commercial 100 t Creusot-Loire-Uddeholm (CLU) converter used in the manufacture of stainless steel in South Africa. Dimensional analysis was done to correlate mathematically the dispersed phase holdup with the operating conditions and the modified Froude number. The overall expression of the holdup revealed that the dispersed slag phase decreased with the vertical distance from the original interface between the liquid phases. The dispersed phase also decreased with the radial distance in the water plume zone toward the sidewall. The holdup was apparently much higher on the side of the reactor where there were no tuyeres. The modified Froude number ensured the correlation between the model and the prototype.

Jan 1, 2014

By D. Vogt

South African underground hard rock mines are typically managed using measurements made daily, weekly or even monthly of key parameters such as face advance, readiness to blast, blast success, temperature or dust levels. Health, safety and productivity can all be greatly improved if a real-time measurement system can inform decision making. To enable this vision of widespread sensing, communication and decision support, CSIR has developed an open standard architecture for communication of sensor data, and a reference implementation using that standard. The standard, called AziSA, meaning ?to inform? in isiZulu, will allow any device that complies with it to join any network that supports it. The standard is designed for South African gold and platinum mines. To be practical in a typical Bushveld platinum mine, a real-time sensor system needs to be robust, reliable and cheap: ?Sensors are equipped with power sources that will last as long as the sensor is required. In effect, sensors need to be disposable: cheap enough not to warrant repair if they break. ?Communication in the stope is wireless, to avoid there liability problems associated with wire connections. For example, wires to sensors in the face area are unlikely to survive blasting. ?To get information out of the stope, the power line to the scraper winch is used as a communications link. Unlike a separate communications link, the power line will be repaired if damaged, because of its importance to production. ?Outside the stope, communications are transferred onto the mine communication infrastructure. To succeed as a management system, the next key element is the use of software decision support tools that will analyse masses of real-time data to extract key parameters and trends for decision makers. A range of sensors has been developed, including commercial sensors that have had wireless adapters added to make them AziSA compliant, and bespoke sensors that provide low cost sensing of typical mining parameters. An important parameter in any sensor network is the location of the sensor. This has to be easy and cheap to establish, so a tool has been developed to locate sensors in the confines of a stope, using ultrasonic and radio techniques. Once sensors are installed and located, they associate their location to all data that they produce. All the data from the system are captured at surface in a flexible database that can be queried by any application that requires data of any kind. It is simple to program alerts, and for actions to be associated with alerts. The use of wireless in stope also allows for communication from surface to the stope, or from stope to stope. The first implementation of an AziSA compliant system is being installed as part of the Mine Health and Safety Council funded rockfall elimination project. The design is discussed, and a future application for a platinum mine is considered.

Jan 1, 2009

By B. P. Watson

Several large falls of ground occur annually in the narrow, tabular stopes mined in the Bushveld Complex. These falls comprise safety risks and cause substantial production losses and compromise efforts to increase productivity. Underground observations in conjunction with instrumentation sites were used to establish the strategic parameters required to describe the rock mass behaviour of shallow-dipping stopes on the Bushveld platinum mines. Existing rock mass rating systems were evaluated using the observations and instrumentation results. None of the current systems adequately described all the relevant geotechnical conditions. Thus a hybrid of several current systems was developed, and the proposed system is discussed in the paper. The new rock mass rating system is termed the ?New Modified Stability Graph? system and follows the method originally described by Mathews et al.1and revised by Hutchinson and Diederichs2.Changes have been made to some of the tables provided by Barton3and to the stress analysis suggested by Hutchinson and Diederichs2. In addition, the logistical regression analysis has been applied to databases, formed using the suggested analyses, for three support resistances and risk levels established.

Jan 1, 2004

The optimum cut-off grade policy maximizes the net present value (NPV) of an open pit mining operation subject to the mining, processing, and refining capacity constraints. The traditional approaches to cut-off grade determination ignore the escalation of the economic parameters such as metal price and operating costs during life of an operation, and consequently lead to unrealistically higher values of the objective function. Further, the NPV of a mining operation declines due to the depletion of the available reserves, causing a decline in the optimum cut-off grade, i.e. higher cut-off grades in the early years of an operation and lower cut-off grades during the later years. Hence, low grade material mined in the earlier years may be stockpiled for processing during later years to offset the effect of escalating economic parameters on NPV. This paper demonstrates the combined impact of introducing economic parameters, escalation and stockpiling options into the cut-off grade optimization model. The model promises an enhancement in NPV as illustrated in a case study incorporating practical aspects of an open pit mining operation.

Jan 1, 2011

By D. K. Weatherley, T. P. Oladele, L. B. Bbosa

Comminution is a critical stage of mineral processing which aims to reduce the size of ore particles through breakage, consequently increasing the likelihood of liberation of valuable minerals. Several factors, such as pre-existing cracks, mineralogical composition and particle size, are known to affect ore breakage behaviour. While investigating the contributing role of each factor is essential to improve understanding of breakage, isolating individual factors by experiment is typically impractical. Numerical techniques such as the Bonded Particle Model-Discrete Element Method (BPM-DEM) have been developed as a means of studying closely controlled breakage conditions. This study evaluates this technique in modelling the effect of pre-existing cracks breakage behaviour for synthetic ore specimens during impact breakage in a short impact load cell (SILC). Synthetic ore was modelled as a collection of discrete entities connected by brittle-elastic beams. Model parameters were calibrated against macroscopic material properties of a conventional homogenous synthetic ore. The extent of pre-existing cracks within specimens was prescribed by varying discontinuities between the connecting entities. An approach with the insertion of seed points was used to model the mineralogy of the specimens. Results showed that pre-existing cracks resulted in a decrease in the fracture force as the crack density increased. Additionally, the irregularity of fracture patterns within rock specimens after impact became more apparent as the crack density increased. The findings were used to emphasise some of the attributable causes of the variation observed between ore hardness characterisation tests and in situ ore behaviour. Keywords: Element Method; Bonded Particle Model, synthetic rock sample; rock fracture, preexisting cracks

Jan 1, 2020

By C. J. Badenhorst

The scope of this project was to research, develop and eventually produce a personal occupational hygiene and safety exposure monitor system to assist in recording and analysing various stress factors that could affect the health, wellness and safety of employees, i.e. that could result in injury or ill health of workers, create stress build-up within individual workers that could negatively affect worker alertness and safety, and, may even result in permanent disability or death. Utilized systems at the time were all reactive, whereas the DOHEMS (Proactive Digital Occupational Hygiene and Safety Exposure Monitoring) System enabled the measurement of exposure (and associated risk) in a proactive manner via real-time exposure and digitized recordings. The idea of the development was to create a unit that is so cost effective, small and light that every worker can use a system on a daily basis. The development will eventually replace current, bulky and expensive monitoring equipment. The device must be a portable battery operated device and monitor the immediate working environment by periodic sampling for vibration, noise, toxic gasses (NO/NOX/CO/VOC, etc.), body temperature and heart rate. The samples must be time and date stamped, utilizing a real-time clock (RTC) synchronized with the closest regional secondary time source and related to synchronized real-time video captured samples. These samples are then recorded onto a rugged non volatile storage device with the capacity to store a vast number of samples covering the entire working shift of eight (8) hours plus. The system has been fitted with a clear visual local alarm indication system, indicating any excessive exposures or stresses, for the worker?s supervisor to respond to. This system allows for a pro-active approach. The system is also a wireless system (to the external environment) so as to not affect the mobility of an employee and flameproof to allow for use in explosive environments. Keywords: safety, digital, exposure, monitoring, proactive.

Jan 1, 2010

By S W. Robertson, A Vercuil, P Craven

Mintek is currently developing a design approach for the heap leaching of low-grade primary copper sulphide material. Since the leaching of chalcopyrite requires elevated temperatures, the generation and management of heat within the heap is crucial. Furthermore, the precipitation of iron needs to be managed to prevent premature blinding of the heap, and acid consumption needs to be limited to contain cost and limit the dissolution of gangue impurities. Standard column tests using jacketed 1-m and/or 6-m columns do not allow accurate prediction of temperature changes and heat generation in an actual heap. Mintek therefore utilizes a computer model to calculate the energy balance and heat generation with time, based on the measured sulphide oxidation rates in the column. The temperature in the column is then adjusted to reflect the computer-predicted temperature in an actual heap. Using this approach, an overall copper extraction of 70% was achieved in 120 days, using 1-metre columns, when treating an ore blend containing 1.36% chalcopyrite, 0.23% chalcocite, 0.07% covellite, 3.8% pyrite and silicate gangue (92%). The chalcopyrite contribution to the total copper content in the feed was 75%. This was followed by 6-m columns using a similar approach, and the column results will be validated on a 23,000 tonne test heap. Key Words: heap; bioleach; chalcopyrite

Jan 1, 2005

1. Book reviews Geophysical and geochemical techniques for exploration of hydrocarbons and minerals, edited by M. Sittig. (Reviewer: J. Keenan) Separation procedures in inorganic analysis. A practical handbook, by Roland S. Young. Charles Griffin, 1980. £23.00. (Reviewer: R. Murray-Smith) 2. Historical reprints Theinin~rs dictionary, by William Hooson. £14. Discovery of subterraneal treasure, by Gabriel Plattes. £12. Fodinae Regales (The Mines Royal), by Sir John Pettus. 3. De Beers' booklets Amborite - a remarkable new cutting material, by De Beers Industrial Diamond Division (P.O. Box 916, Johannesburg 2000). Booklet, 14 pp., free of charge. Natural and synthetic micron powders, by De Becrs Industrial Diamond Division (P.O. Box 916, Johannesburg 2000). Leaflet, 5 pp., free of charge. 4. New books Nickel in the environment, edited by J. O. Nriagu. New York, Wiley, 1980.928 pp. $65. Underwater minerals, by D. S. Cronan. London, Academic Press, 1980. 364 pp. $57.50. Data conversion integrated circuits, edited by D. Dooley. New York, Wiley, 1980.298 pp. $26.95 (cloth), $17.50 (paper). 5. NIM reports Report 2057 A mineralogical study of the Rooibokkop- Boschhoek copper deposit in the Marble Hall area. Report 2069 A utomatic setting of the distance between sample and detector in gamma-ray spectroscopy. Report 2070 The prereduction of chromites from the UG-2 Reef. Report 2075 The optimization of some of the conditions for analysis by spark-source mass spectrometry. Report 2082 A survey of the literature on gravity separation.

Jan 1, 1981

By J. van Deventer

Ion exchange is widely used in hydrometallurgical operations for the recovery and purification of valuable metals. Special chelating resins have a high affinity for specific elements, allowing the selective removal of low levels of impurities from a background of highly concentrated valuable metal. Solvent-impregnated resins have been added to this group more recently, expanding the treatment options. These products find application in the purification of cobalt-rich liquor prior to the production of high-purity metal or metal salts. Impurities in copper-cobalt circuits that are typically targeted by ion exchange include iron, uranium, copper, zinc, nickel, bismuth, and antimony. Ion-exchange resins can also be used to treat tailings, thereby recovering additional valuable metal and improving the Environmental and Social Governance credentials of the operation. This article takes a look at various applications of ion exchange in copper-cobalt operations

Jan 1, 2023

By K. C. Corin, M. Tadie, N. Ndamase

Fresh water conservation efforts and strict environmental regulations have forced the mining industry to reduce freshwater consumption and effluent discharge. This is achieved by recycling process water back to mining processes. The performance of flotation circuits depends on the pulp chemistry. When process water is recycled to flotation cells, organic and inorganic species that have accumulated over time alter the pulp chemistry. The presence of accumulating ionic species such as SO4 2- and S2O3 2- has been found to hinder the adsorption of collector ions onto mineral surfaces. Sulphide minerals are semi-conductors; electrochemical reactions take place on their surfaces. The adsorption of collectors onto mineral surfaces takes place via electrochemical reactions. This study, therefore, aims to investigate how the presence of accumulating ionic species at varying ionic strengths affects the adsorption of sodium ethyl xanthate onto chalcopyrite from an electrochemical perspective. Synthetic plant water comprised of single salts with varying ionic strengths was used. Rest potential measurements were conducted to investigate collector-mineral interactions in the presence of these ionic species. Microflotation tests were performed to determine whether the presence of these ionic species affects mineral floatability. Higher chalcopyrite recoveries were achieved in the presence of SO4 2- than in the presence of S2O3 2-. Rest potential measurements were found to successfully predict microflotation performance in the presence of the ions of interest. Keywords: Flotation water quality, electrochemical adsorption; xanthate collectors

Jan 1, 2020

By M. R. MacIver, M. Pawlik, S. Finora, H. Alizadeh

The dispersion of mature fine oil sands tailings (MFT) by the addition of sodium lignosulfonate was studied using contact angle measurements, optical scattering, and particle size measurements. Lignosulfonate caused the release of residual bitumen to the slurry surface and settlement of fines. Dynamic contact angle by captive bubble measurements were carried out on bitumen to determine the effect of the dispersant on the wettability of bitumen. Lignosulfonate caused a change in the aggregation state of the MFT and increased sedimentation of particles, as indicated by optical scattering measurements. Zeta potential measurements indicate that this change was caused by an increase in adsorption of lignosulfonate onto particles, which caused improved settling of the colloid. Ultraviolet Visible (UV) spectrophotometry and organic carbon content measurements showed that only a small amount of the reagent remains in the aqueous phase of the tailings, which is critical for decontamination of recycled water. Keywords: Oil sands tailings, bitumen recovery, dewatering, dispersion, surface chemistry

Jan 1, 2020

By D. F. Malan, J. A. L. Napier

A number of shallow coal or hard rock mines employ pillar mining systems as a strategy for roof failure control. In certain platinum mine layouts, pillars are designed to ‘crush’ in a stable manner as they become loaded in the panel back area. The correct sizing of pillars demands some knowledge of the pillar strength and the overall layout stress distribution. It is particularly important to understand the impact of the layout geometry on the effective regional ‘stiffness’ of the rock mass around each pillar. An important design strategy is to model relatively detailed layout configurations which include a precise representation of the local pillar layout geometry and to analyse multiple mining scenarios and extraction sequences to select optimal pillar sizes and barrier pillar spacing. Although computational solution techniques are now impressive in terms of run time efficiency, a major difficulty is often encountered in assigning suitable material properties to the pillars and in devising an effective material description of the layered rock strata overlying the mine excavations. This paper outlines an efficient numerical strategy that can be used to assess large-scale pillar layout performance while retaining the ability to modify individual pillar constitutive behaviour. The proposed method is applied to selected layouts to compare estimated average pillar stress values against values determined by detailed modelling and against observed behaviour.

May 3, 2023

By S. Banisi, M. R. Yarahmadi, S. R. Mortazavi

Nowadays the development of automatic on-line sampling systems has enabled large amounts of data to be available to plant managers. These data are inevitably prone to random and sometimes systematic errors. Data reconciliation methods are used to deal with random errors. In these methods, the measured data are adjusted in accordance to their error, so that the mass conservation law is satisfied at the same time. Measured data may also contain systematic errors, using these data in mass balancing software will result in inaccurate or even irrational results. In this paper three methods for detecting systematic errors (global test, node constraint test and maximum power constraint test) were presented. A step by step method to locate the systematic errors was demonstrated. Then, the new version of Movazen©, a mass balancing software, was introduced and used to locate systematic errors in the measurements taken from the Sarcheshmeh pilot plant copper flotation circuit. Keywords: Mass balancing, data reconciliation, random error, systematic error

Jan 1, 2020

By J. C. Barry, J. H. van Laar, P. L. Crouse, H. Bissett, I. J. van der Walt

"Plasma-assisted spheroidisation of metal powders offers several technical advantages with respect to both the ease of materials handling and powder-metallurgical item manufacturing. Advantages include improved flowability, increased powder packing density, elimination of internal component cavities and fractures, changes in morphology resulting in decreased friction between particles and contamination during pneumatic transport and enhanced particle purity. In this empirical study, spherical iron particles were produced using a microwave plasma operating at atmospheric pressure and characterized using optical microscopy and SEM techniques. Iron powders were fed into the system at fixed operating conditions, resulting in particles with spherical structures. The theoretical estimate of the time required for melting to occur is 1.6 ms, an order of magnitude smaller than the actual residence time. IntroductionParticle design and functionalization has become an increasingly popular aspect of materials synthesis and powder-metallurgical item manufacturing. One such technique involves the spheroidisation and densification of feed materials, typically in the form of chemical powders with wide particle size distributions. The major benefits of powder spheroidisation include improved powder flowability, increased powder packing density and powder purity, reductions in internal voids and defects, as well as the ability to manipulate the particles surface morphologies (Boulos, 2004). Thermal plasma processing has the potential for scale-up and for producing industrial quantities of spheroidised powder.Thermal plasma technologies offer a wide spectrum of material synthesis and treatment options, amongst others the synthesis and spheroidisation of nano-sized ceramic and metal particles (Kumar and Selvarajan, 2006). The spheroidisation process occurs within the plasma discharge via in-flight heating and melting of the powder feed material, given high enough plasma temperatures (Fridman, 2008, p. 495). Surface tension in the molten droplets results in spherical, or nearly, spherical, powder particles being formed upon exiting the plasma discharge where the droplet undergoes rapid cooling and freezes. Quite often, the bulk density of these spherical particles is higher than that of the starting material (Boulos, Fauchais and Pfender, 2013, p. 42). The different plasma spheroidisation techniques reported include radio frequency (RF) induction thermal plasmas (Jiang and Boulos, 2006; Karoly and Szepvolgyi, 2005; Yuming, Junjie and Yanwei, 2013), nontransferred direct current (DC) thermal plasmas (Chaturvedi et al., 2014; Kumar and Selvarajan, 2008; Suresh, Selvarajan and Vijay., 2008) and microwave-assisted plasma processing methods (Chen, Gleiman and Phillips, 2001; Vanamu et al., 2004; Weigle et al., 2004)"

Jan 1, 2016

By M. Pelser, J. Hagemann

"The Anglo American Platinum Rustenburg Base Metals Refiners (RBMR) is the largest producer of nickel cathode in South Africa. It treats slow-cooled matte to recover a platinum group metal-containing magnetic fraction for downstream processing and a nonmagnetic fraction to produce nickel and copper cathode, cobalt sulphate, and sodium sulphate. The refinery was recently expanded from 21 to 33 kt/a nickel. During the ramp-up phase, the sulphur removal section was found to be a constraint to throughput. Nickel hydroxide is precipitated from nickel spent electrolyte by addition of sodium hydroxide, and filtration of the nickel precipitate allows sulphur to be removed from the circuit as aqueous sodium sulphate in the filtrate. The filtration fluxes were found to be limiting the circuit’s capacity. An obvious solution would have been to install additional filtration capacity at significant capital cost and long lead times. RBMR chose rather to first initiate a collaborative project with Anglo American Technical Solutions to better understand the impact of process conditions on filtration characteristics and to evaluate whether the filtration flux could be increased by improving the quality of the nickel precipitate.A deeper understanding of nickel hydroxide precipitation chemistry and kinetics in the context of high nickel and sodium hydroxide concentrations was developed, guided by precipitation theory and confirmed by laboratory tests and plant observations. It was found that the filtration rate could be significantly improved by modifying the precipitate characteristics. A new precipitation process was engineered and retrofitted into the existing plant. Since start-up of the new precipitation system, the available capacity of the sulphur removal section has more than doubled, and control of the process has improved with the better agitation. This paper describes the theory and results used to design the new agitation system, as well as the impact of the change on capital investment, operability, and process efficiency."

Jan 1, 2016

By C. W. P. Finn

INFACON is of special significance to people in South Africa who are interested in ferro-alloys, because it was in South Africa that the idea of regular international congresses on ferro-alloys was conceived and developed. INFACON 74, the first-ever such congress, was held in Johannesburg from 22nd to 26th April, 1974, being organized by the South African Institute of Mining and Metallurgy, the National Institute for Metallurgy, and the Ferro Alloy Producers' Association of South Africa. Design Awards The Design Institute is inviting entries for the 1981 Shell Design Awards. Any product that falls into the three categories shown below, and that was designed in South Africa and is in production, is eligible for an award. Since their inception in 1970, the Shell Design Awards

Jan 1, 1981

By T. R. Marshall

SAMREC (The South African Code for the Reporting of Exploration Results, Mineral Resources and Mineral Reserves) Clause 7 notes that ‘Documentation detailing Exploration Results, Mineral Resources and Mineral Reserves from which a Public Report is prepared must be prepared by, or under the direction of, and signed by a Competent Person.’ Similar statements with respect to Competent Valuators (CVs) and Qualified Reserves Evaluators (QREs) are contained in the SAMVAL (South African Code for the Reporting of Mineral Asset Valuations) and SAMOG (South African Code for the Reporting of Oil & Gas Resources) codes respectively. What does it mean to be a Competent Person (CP) in the context of compiling/signing-off on SAMCODE (South African Mineral Code) compliant documents? What do the registration and experience requirements mean? Who is ultimately responsible for the report and what does such responsibility prescribe?

Sep 1, 2021

By N. du Preez, J. Christie, F. Crundwell

Precipitation is a key process in the recovery of copper and cobalt. While there is a wealth of experience in operating precipitation steps, improving their performance remains challenging. Chemically, the reaction might be controlled by reaction kinetics, be limited by oxygen mass transfer, or be at equilibrium. In this paper, we examine these different operating regimes and demonstrate how they can be identified from plant operating data, process modelling, and pilot plant test work

Jan 1, 2023

By K. A. du Preez, P. J. van Staden, M. van Rooyen

Mine-impacted water, including acid mine drainage (AMD), is a global problem. While precipitation of dissolved metals and neutralization of acidity from mine-impacted water is accomplished relatively easily with lime addition, removal of sulphate to permissible discharge limits is challenging. This paper presents a high-level comparison of four sulphate removal technologies, namely reverse osmosis, ettringite precipitation, barium carbonate addition, and biological sulphate reduction. Primarily operating costs, based on reagent and utility consumptions, are compared. Each process is shown to be subject to a unique set of constraints which might favour one over another for a specific combination of location and AMD composition. Access to and cost of reagents would be a key cost component to any of the processes studied. The total cost calculated for each process also depends on the type of effluents that are allowed to be discharged.

Oct 1, 2021

By Rodney Ishak, Merete Tangstad

In the HC FeMn production, better utilisation of coke and electric power is vital for reducing the production costs. The higher manganese oxides in the charge are reduced to MnO in the prereduction zone, where also the Boudouard reaction is active. These gas-solid reactions are to a large extent decisive for the total consumption of both coke and electrical power in ferromanganese production. In the present work formulas for calculating the Degree of prereduction have been developed for industrial practice. It shows that the typical Degree of prereduction is between 10-40%, but it may in good periods be as high as 60%. Statistical analysis has been done in order to find how various operational parameters influence the Degree of prereduction. A few parameters were observed to have an effect on the prereduction. Comilog ore definitely had a positiveinfluence on the prereduction, Comilog sinter and Mamatwan ore probably had a positive influence on the prereduction, all in relation to the average prereduction in the selected periods. Meanwhile, As man ore definitely, % H2O in raw materials and increasing Hd probably, had a negative influence on the prereduction. The findings for these raw materials were very much in coherence with the results of laboratory scale experiments performed, where the CO-reactivity of different ore materials was studied.

Jan 1, 2007