Search Documents

By J. L. Ellenberger, G. S. Esterhuizen, T. Miller, M. M. Murphy

A limestone mine in Ohio has had roof instability problems that have led to massive roof falls extending to the surface. This paper describes a collaborative study of these events undertaken by the National Institute for Occupational Safety and Health and the mine owners. The study focuses on the roles that weak, moisture-sensitive floor and weak bands in pillars play in a general instability that led to roof falls at this mine. The NIOSH Stone Mine Pillar Design software (S-Pillar) does not include analysis for weak floor or weak bands and recommends that when such issues arise they should be investigated further using a more advanced analysis. It is important to recognize that without the impact of the floor or weak bands, the calculated inherent stability factor for these pillars is within the recommended design range. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to help determine the failure mechanism. Roof-to-floor convergence monitors were also installed in the areas predicted to have further instability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface. This recent case demonstrates that weak floor can be a significant factor in pillar stability and should be assessed during the design stage of the mine.

Jan 1, 2015

By Corale L. Brierley

Bacteria, algae and fungi react to heavy metals in their environment by immobilizing, mobilizing and/or transforming metals. Microorganisms carry out these changes by (1) precipitating metals outside of the microbial cell, (2) binding and complexing metals to the outside of the microbial cell's protective coating, (3) accumulating metals inside of the microbial cell, or (4) transforming metals by oxidation, reduction, methylation or demethylation. Most of these mechanisms are operative in constructed aerobic and anaerobic wetlands for metal's remediation. Several more advanced biotechnologies for metal's removal from aqueous streams have been introduced, but have not been widely accepted commercially.

Jan 1, 1995

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

Many modern industries rely on rare earth elements (REEs) to produce products that are essential to both civil and defense applications. In a prior study (Vass et al., 2019), we showed that REE grades in acid mine drainage (AMD) and associated byproduct precipitates from AMD treatment (AMDp) warrant evaluation as a feedstock for REE production. The current work extends that effort through a broad survey of 141 AMD treatment sites in Northern and Central Appalachia. In this study, 185 raw AMD and 623 AMDp field samples were obtained and analyzed to assess the REE and major metal concentrations. Results show that an average of 282 μg/L and 724 g/t of REEs occur in AMD and AMDp, respectively. Additionally, both basins contained similar distributions of REEs, and these distributions tended to favor heavy and critical REEs when compared with traditional REE ore deposits. 

By Taeyong Lee, Cole Bales, Matt Fowler, John Horne

Mitchell Point Tunnel near Hood River, Oregon is one of the more unique segments of the Historic Columbia River Highway and State Trail being constructed through the Columbia River Gorge. This 650-foot bike/pedestrian tunnel set to open in 2024 is being delivered by FHWA in partnership with Oregon DOT, Oregon State Parks, and the U.S. Forest Service. Primarily driven using drill & blast excavation methods through basalt, the shotcrete and dowel-supported tunnel features masonry portals and ve window adits that provide illumination and views of the river similar to the original highway tunnel of many vistas built in 1915 that was removed in 1966 to make way for Interstate 84. This paper summarizes the planning, design, and construction.

Jun 23, 2024

By Yongheng Jiang, Wentong Wang, Haoming Luo, Chuanju Liu, Qianjun Zhang, Sha Guo

Rock burst has always been a major problem in deep underground engineering with high stress, and rock burst strength evaluation has become an important research topic. To effectively predict the rock burst hazard in underground rock mass engineering, a cloud model (CM) rock burst intensity evaluation method based on the CRITIC method and order relation analysis method (G1) was proposed in this paper. First, a rock’s uniaxial compressive strength σc, tangential stress σθ, uniaxial tensile strength σt, ratio of uniaxial compressive strength to tensile strength σc/σt (brittleness coefficient), ratio of tangential stress to uniaxial compressive strength σθ/σc (stress coefficient), elastic deformation energy index Wet, and depth of cover H were selected as evaluation indices of rock burst intensity. Ninety-five groups of rock burst measured data at home and abroad were selected, and the objective weight and subjective weight of each index were calculated by using the CRITIC method and G1 method, respectively. The comprehensive weight was determined according to the combined weighting method of game theory, and the sensitivity of each evaluation index was analyzed. By utilizing a forward cloud generator, the membership degrees of different rock burst grades were calculated, and then the rock burst intensity grades of the samples were evaluated and compared with the evaluation results of the CRITIC-CM method and G1-CM method and the actual grades. Finally, the rock burst classification ability of the model was analyzed. To better verify the accuracy and reliability of this model, the rock burst case of the W39 line in the Chengchao Iron Mine was analyzed by using this model. The research results show that the rock burst evaluation results based on CRITIC-G1-CM are basically consistent with the actual rock burst grade, and the rock burst intensity grade evaluation model has good practicability and reliability.

Sep 1, 2023

By D. M. Davidson

The economics of geologic exploration have changed materially in the past decade primarily due to the change in three basic factors, namely, increased wages and salaries, increased cost of materials, and a greater complexity in methods of exploration. Following the general economic pattern over the past ten years, exploration costs, have, in general, increased, although there is one heartening exception. A comparative picture is complicated because of advances in techniques which ensue from the introduction of new methods and devices largely for aerial exploratory work, Some of these methods were either in their infancy or unknown before World War II. Geological exploration may well be considered as a form of applied research. True, it has peculiarities from this standpoint some advantageous, others disadvantageous, Some of the advantages lie in the fact that exploration success does not involve the production of a new product which necessitates advertising expense and marketing problems. In normal times there is a well established market for the fruits of a successful mineral find. The outstanding disadvantage of exploration lies in the enigma of deciding when to quit if the sought fop prize is elusive. In the search for buried treasure, man?s curiosity is apt to color his judgment. Even the so-called detached scientist may fall 'all too readily into the wishful thinking of the old- time prospector who is lured on by the thought that the next pull from the drill hole, or the next round from the face will reveal a bonanza. It involves mature judgment and experience to ascertain the stage in exploration when further work is not justified.

Jan 1, 1958

By J. Grubb

"The undertakings described in the paper titled “Study on correlation of quantified coal rank with self-heating temperature” by Wang and Luo in the November 2015 issue of Mining Engineering (Wang and Luo, 2015) are mathematically sustainable and an acceptable extension of work performed by Smith and Lazzara (1987) for the U.S. Bureau of Mines. The paper is not an accurate explanation of the currently accepted leading practice for determining the propensity of a coal seam for spontaneous combustion. The paper could lead a practitioner to an oversimplified conclusion on how to determine the propensity of a coal seam to spontaneously combust.The spontaneous combustion of coal is a complex and not fully understood reaction. What is understood is that many more factors other than selfheating temperature (SHT) and coal rank are required to sufficiently evaluate the risk of spontaneous combustion in a particular coal seam. A superficial assessment can lead to an improper response to the risk. Some statements on the next steps through an appropriate literature search would have made the authors’ conclusions more credible.The SponCom 2.0 software, updated by the National Institute for Occupational Health and Safety (NIOSH) in 2011, provides a path for evaluating the susceptibility of a coal seam to spontaneous combustion. In addition to proximate and ultimate analyses to establish coal rank, and therefore an estimate of SHT, the program includes the history of heatings, friability, seam thickness, overburden thickness, rider seam presence, pyrite presence, face and butt cleat densities, geothermal source presence and other geological features in the assessment. Mining conditions including floor heave, rib sloughage and rate of advance are also assessed to conclude a propensity for spontaneous combustion."

Jun 1, 2016

By S. Ripke

Between 2002 and 2004, the performance of a six million ton per year iron ore beneficiation plant dropped significantly. In a classic case of “who done it,” was it the mine, the concentrator, an ore change, or something else? While average annual final product grade decreased 8% (indicated by an increase in silicate gangue from 2.76% to 2.99%), the weight recovery also decreased by 8% (from 37.92% to 34.79%). This represents a loss of 832,000 tons of iron ore worth about $16 million for the two year period! The concentrator had been optimized to produce a high grade wet concentrate as feed to the dry side of the plant. But, did optimizing an individual unit operation’s grade give the best overall plant performance? In this paper, the investigation and solution to this mystery will be revealed.

Jan 1, 2007

"A long-term mine production schedule optimization based on stochastic integer programming is presented that manages the risk due to geological variability and uncertainty while jointly considering mine profitability, truck fleet requirements and waste management. The evolution of the pit is controlled so that space within the mined-out pit is continuously provided to allow for tailings and waste rock to be replaced, thus minimizing the project’s environmental footprint. The method is applied at a taconite iron ore deposit and has a project net present value that is 16.9 percent higher than that of a conventional schedule and has a higher chance of meeting production forecasts. The stochastic schedule reduces equipment requirements by delaying waste mining and by mining selectively in order to meet plant ore feed requirements without stockpiling material, resulting in 23.7 and 26.2 percent lower mining capital and operating costs, respectively. IntroductionThe LabMag iron ore deposit is part of the Millennium Iron Range, a 210-km (130-mile) belt of taconite in northern Quebec and Labrador, Canada. LabMag has significant economic potential. It contains more than 3.3 Gt (3.6 billion st) of proven reserves at an average total iron content of 29.8 percent and is very low in impurities. However, on a project basis of 23 Mt/a (25 million stpy) of product, the required capital expenditure is estimated at more than $5 billion (SNC-Lavalin, 2014), which necessitates careful evaluation of all sources of risk. Resource estimation is one of the main sources of risk in a mining project as knowledge of the orebody is primarily based on drilling, which is often sparse because it is expensive. If the expected ore tonnages and qualities are not obtained when mining, the project cash flows are directly affected. The expected quantities and qualities of ore and waste are defined by the mine production schedule, which specifies the sequence of extraction and is dependent on the resource estimation. The goal of mine production scheduling is thus to maximize the expected profit, while also meeting all production targets and constraints, by creating an extraction schedule that is robust in the face of geological risk and has the highest chance possible of actually being realized."

Jan 10, 2017

By F. M. Benavides

This paper presents recent developments in federal environmental regulations, which in the view of the author, affect mining and the mineral processing industries. This is a summary of activities by the administration, congress and regulatory agencies during 1990. The information presented is a recap from material published. The emphasis is given to Air Quality regulations, although other environmental concerns are reviewed.

Jan 1, 1991

By David Atkin

This paper presents methods and results of environmental planning conducted for a proposed coal and iron ore transshipment terminal which would be located on reclaimed land west of Lisbon, Portugal. Oceanographic, navigational, marine, structural, material handling, and financial studies of the terminal were conducted along with the environmental analyses. However, because of the proximity of the terminal to heavily used recreational resources, residential areas, and biologically valuable habitat, anticipating and reducing the environmental effects of the terminal to minimum levels was a very important part of the overall project. The results of the study indicate that even the impacts associated with worst-case conditions would be acceptable because of appropriate pollution control measures and planning.

Jan 1, 1983

Precious metals exploration is increasingly involved with concealed, deeper-seated gold-silver deposits which exhibit considerably more challenges to the geologist than near-surface, oxidized ores. Thus, cost-efficient, rapid and more detailed target selection and definition will be crucial for gold-silver exploration in the 1990s (Kral, 1990; Woodall, 1992). Although new developments in geophysical and geochemical exploration techniques have made significant contributions, the powerful capabilities offered by alteration mineralogy continue to remain untapped in many cases

Jan 1, 1993

By J. Navoyski, B. Macdonald, W. J. Helfrich, J. L. Bellanca, B. Demich

DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the official position of the National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention. Mention of company names or products does not constitute endorsement by NIOSH. ABSTRACT The pervasiveness of high-fidelity video games raises expectations of quality, detail, and lighting in virtual reality (VR) applications. However, high-quality models of mining equipment and environments are often not readily available, and developers may not be familiar with the latest techniques, such as physically based rendering (PBR). Because a consistent aesthetic is critical for maintaining immersion and controlling visual stimuli in research as well as in training, researchers at the National Institute for Occupational Safety and Health (NIOSH) created an asset development workflow. This paper details this workflow, including precision modeling and PBR techniques as well as a rigorous review process. It also describes lessons learned in the creation of photorealistic VR assets. BACKGROUND Virtual reality (VR) describes the simulated experience generated by an assemblage of hardware and software that are used to immerse the user. Over many years VR developers targeted the development of virtual environments (VE) toward various purposes: entertainment, the treatment of phobias [1], rehabilitation [2], and training [3]. A large part of the VE development includes digital assets, where digital assets refer to the non-programmed elements including 3D models, audio, and user interface. Because vision provides nearly 10Mbps of data [4] and accounts for the majority of all sensory input combined [5], a focused effort on asset appearance in VEs is warranted. Furthermore, research has shown that higher-resolution imagery increases search performance and training transfer, necessitating high-fidelity assets [6, 7]. In addition to being visually appealing, it is important that the assets and environment are also dimensionally accurate and consistent in order to elicit appropriate responses from the end users as they interact with and among these items [8, 9]. Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed VEs and digital assets under several research projects over the course of the last two decades [10, 11, 12, 13]. This work has provided researchers with a strong knowledge base for digital asset development. However, the assets themselves have had limited reuse value. Due to the extended timeframes and limited scope of these projects, the previously developed assets are not consistent in visual quality and dimensional accuracy. Moving forward, researchers wanted to minimize future development time and use of resources as well as adopt new asset development tools and game engine technology. Therefore, the aim of this paper is to document a new asset development workflow including geometry, materials, UV layout, and shader implementation combined with review steps in order to produce high-fidelity simulation assets that are accurate with consistent characteristics, using repeatable methodologies that are well documented.

Jan 1, 2019

By Gregory A. Hahn

Explorationists and engineers rarely speak the same language. Explorationists are not cognizant of the information that engineers require to make the appropriate choices and decisions. Engineers can- not "translate"geo1ogic parlance and data into information relevant to proper decision making. This often creates a physical and intellectual "rift" between engineers and geologists that inhibits a smooth transition to development. A transition team leader who is grounded in both disciplines can best facilitate integration and communications between the explorationists, who understand the intrinsic attributes of a given deposit, and the engineers, who have to design for extraction and beneficiation of an orebody.

Jan 1, 2001

The Cutoff grade optimization is very critical to the open pit production scheduling. In case of single mineral deposits, algorithms have been developed for determining cutoff grade policy that maximizes the net present value (NPV) of yearly cash flows. For deter-mining the cutoff grade policy for projects with two minerals including stockpiles the problem becomes much more complex. The purpose of this paper is to present fundamentals of a generalized cutoff grade optimization algorithm that will maximize the NPV of a project subject to mining, milling, and marketing constraints. Benefits of the methodology developed are demonstrated on three different case studies.

Jan 1, 1997

By Charles L. Karr

Grinding is a necessary component in the processing of a number of minerals, and improvements in this area could provide substantial cost savings for the minerals industry. Optimizing the process of grinding, however, is a difficult task because there are multiple objectives; i.e., several aspects of the process are important including the fineness of the ground product, the energy consumed in the process, and the viscosity characteristics of the final slurry. Genetic algorithms (GAs) are search algorithms based on the mechanics of natural genetics and have been proven capable of solving multiple objective optimization problems. These robust search techniques are able to rapidly locate near-optimum solutions across a broad spectrum of very difficult optimization problems. In this paper, two varieties of GA are used to optimize a grinding process as it is described by a computer model: (1) a simple genetic algorithm (SGA) and (2) a micro genetic algorithm (MGA). The performance of these techniques is compared to the performance of a more conventional search technique, a simplex algorithm. Results indicate that the GAs are efficient, versatile, quite capable of improving the grinding process, and easily incorporated into the toolbox of today's process engineer.

Jan 1, 1993

By W. N. McAnulty

Because so many interrelated technical, economic, legal and political factors are involved in evaluation of commercial mineral deposits, it is common practice today to assign such work to a team of specialists including geologists, mining engineers, metallurgists, lawyers, and economic evaluation experts. Each member of the team plays an important role; the role of the geologist is particularly important. The geologist involved with evaluation of fluorspar deposits needs all the geologic and economic training and experience required for evaluation of metallic mineral deposits. Few, if any, industrial or metallic minerals occur in so many geologic environments as fluorite. Fluorspar, and aggregate of rock and mineral matter containing enough fluorite to make a commercial deposit (ore), is somewhat more limited in its modes of occurrence than fluorite, but it too is found in a variety of environments.

Jan 1, 1970

By Faruk Oksuz, Dave Schiemann, Miguel Sanchez, Patrick Jensen

"The McCook Main Tunnel connects Chicago’s Tunnel and Reservoir Plan (TARP) Mainstream Tunnel to the McCook Reservoir. The tunnel system consists of a 10 m (33 ft) finished diameter and 490-m (1,600-ft) long hard-rock tunnel constructed from a 27.5-m (90-ft) diameter and 92 m (300 ft) deep main gate shaft. The gate shaft houses six high-head 4.4 x 9 m (14.5 x 29.5 ft) wheel gates installed in the bifurcated and steel-lined section of the tunnel. The tunnel also includes portal and energy dissipation structures as it daylights into the reservoir. Construction of the McCook Main Tunnel in live flow conditions was a challenging task for the McCook Main Tunnel Project participants, the project owner U.S. Army Corps of Engineers (USACE), local sponsor Metropolitan Water Reclamation District (MWRD) of Greater Chicago, designer Black & Veatch and contractor Kiewit Infrastructure Co. (Kiewit). Once completed in two stages in 2017 and 2029, the McCook Reservoir will hold 38 billion L (10 billion gal) of combined sewer overflows (CSO) and flood waters from the city of Chicago and 36 surrounding communities in Cook County, IL The construction of the tunnel system was divided into two contracts. The first contract for the gate and construction access shaft was completed in August 2011. The second contract included tunnel excavation and concrete and steel lining that was completed in September 2014; installation of gates and hydraulic cylinders that was completed in June 2017; and the last major construction activity was the removal of a temporary concrete plug (bulkhead) and lining that tunnel section to bring the overall tunnel and gates system online before Dec. 31, 2017.This article focuses on the installation, testing and commissioning of the high head wheel gates. Live tunnel connection details to TARP Mainstream Tunnel were addressed in a previous paper submitted at the World Tunneling Conference in 2016."

Mar 1, 2019

By J. K. Ahlness

The Bureau of Mines investigated technologies for determining the integrity of in situ leach mining wells. A self-contained trailer-mounted well integrity testing system (WITS) was designed and built to enable rapid testing of well casings for leaks as required by environmental regulations. The WITS utilizes two inflatable packers to seal off the entire casing length or any portion thereof. Water pressure is built between the packers to the desired test pressure, and the presence or absence of casing leaks is determined by monitoring the pressure drop between the packers. A winch and steel cable are used to run the packers in and out of the well. The WITS underwent an industry field test at the Irigaray in situ uranium leaching mine near Buffalo, WY. A total of 37 wells with an average depth of 225 ft (69 m) were tested at an average rate of four wells per 8-h shift with a two-person operating crew. This represents a 75-pct time savings and an 83-pct labor savings compared to the rigid-pipe method previously used at the mine, with which a three-person crew tested an average of one well per shift.

Jan 1, 1986

By K. Awuah-Offei

The objective of asphalt mix design is to produce a mix with optimal performance using available aggregate stockpiles. Often, this process does not take into consideration aggregate plant stockpile inventories or the cost of aggregate in the mix. This is due to the lack of tools that enable the lab technician or the engineer to optimize the mix for good performance while reducing the cost of aggregate and managing the stockpile inventory levels. The Bailey method provides useful guidance on aggregate gradation selection for optimal performance. This work presents a linear programming model of the asphalt mix design problem. The algorithm is implemented in MATLAB as an Asphalt Mix Design Optimization (AMIDO) program. The program is successfully validated with real-life data. The results show that AMIDO can be used to successfully produce any mix design with known Bailey method ratios. Also, RAP can be included in a design easily by making use of the Bailey method ratios and AMIDO. This work improves the state-of-the-art in asphalt mix design for dense graded mixes and could potentially be modified for other mixes.

Jan 1, 2009