Search Documents

By P. L. Dunn

Automatic control of fine coal cleaning circuits has traditionally been limited by a lack of sensors. Although several nuclear-based analyzers are available, none have seen widespread acceptance. In this investigation, image analysis is used for on-line determination of ash content in fine coal slurries. The ash content of a flotation tailings stream is correlated to the mean gray level of the slurry. Based on a 90% prediction interval, an analysis of sensor performance indicates an accuracy of 73 ± 4% ash over a range from 65-90% ash. While this result is comparable to existing nuclear-based analyzers, the video-based system is only a fraction of the cost. The sensor is currently installed at the Middle Fork preparation plant owned by Pittston Coal Company.

Jan 1, 1997

By R. C. Emmett

The industrial practice of concentration of solids and production of clear solution by gravity sedimentation is an old technology. Through the years, many devices have been designed and built to aid this process. One of the more significant developments was a revolving rake mechanism to convey settled material to a central discharge point of a circular tank, patented in 1907(1). In recent years, clarification systems employing parallel inclined plates have appeared on the market; the original device utilizing this principle was patented in 1886(2). Numerous other methods have been invented, tested, discarded and sometimes re-invented, all with the specific intention of improving the capacity of a particular settling area. Sedimentation theory, as expressed in Stokes' Law, shows that the rate of settling of a particle is directly proportional to the difference in density between the particle and the surrounding liquid and, more significantly, proportional to the square of the particle diameter. Anything that can increase the latter will greatly assist sedimentation and, as a result, flocculation always has been an integral part of sedimentation. Most materials suspended in aqueous media are naturally flocculent to some degree and, hence, are readily concentrated by sedimentation, although sometimes very slowly.

Jan 1, 1978

By D. A. Norrgran

The process of magnetic separation is based on the differences among magnetic susceptibilities of various mineral species. Performed either wet or dry, the separation has application in both the recovery and concentration of value minerals and in removing deleterious mineral constituents from a product stream. There are two major catagories to be considered when addressing magnetic separation of minerals. The first catagory refers to particle characterization and relative differences in magnetic susceptibility. The second catagory refers to design parameters and the magnetic field generated by the separator.

Jan 1, 1987

By Jingzhi Liu, Xueping Hu, Huai Wang, Simin Yang, Baoqiang Yu, Deguang Zhan

In this study, response surface methodology (RSM) and Box-Behnken design to improve copper extraction from refractory copper oxide ore were investigated. Based on single factor tests, quadratic polynomial equation to describe the relationship between influencing factors (particle size, leaching temperature, sulfuric acid concentration, leaching time) and copper leaching rate could be obtained by RSM. The optimum parameters determined by the model are as follows: particle size 64.60% − 74 μm, leaching temperature 74.15 °C, sulfuric acid concentration 0.49 mol/L, and leaching time 140.85 min. Under these conditions, experimental copper leaching rate of 85.12% could be achieved, which was very close to the predicted maximum value (85.34%) by the model, indicating the quadratic polynomial model was accurate and reliable. Copper leaching rate increased approximately by five percentage points comparing to the result of single factor tests. This study indicates that response surface methodology is an effective method to optimize experiment conditions and achieve an ideal experiment result.

Aug 17, 2022

By Arthur W. Ruff

The iron-ore beneficiation and shiploading facilities of the Marcona Mining Company are at San Nicolas Bay which is on the Peruvian coastal desert about two hundred and seventy miles south of Lima. The mines are at elevation of 2,500 ft. Crude ore is transported from the Mine primary crushers to the beneficiation plants by ten miles of overland belt conveyors. After the predominantly magnetic ore is reduced to minus 3/4 in. in the secondary crushing plant, the ore is ground by rod and ball mills and concentrated with magnetic separators. The concentrate slurry is pumped to a thickening and filtering installation for desliming and dewatering. Pelletizing is accomplished with a Lurgi and also a Dravo-Lurgi machine. Deep-water shiploading facilities are available close to the beneficiation plants. Figure 1 shows a flowsheet of the general operation. Pelletizing operations are scheduled 24 hours a day and 365 days per year. A maximum tonnage rate with a high percentage of operating time is necessary to produce the three and one half million tons per year required from the two pellet lines. Process control is a major responsibility and of primary concern to all Operating personnel. The particle size, moisture, and chemical composition of the filter cake must be closely controlled to get uniform high-grade pellets. Key points are sampled routinely and analyzed on a two-hour basis to provide the necessary structure and chemical data to maintain a superior final product. The iron content of the pellets is held between 65.3 and 65.8 percent with 4.0 percent Si02. Sulfur is below 0.04 percent and copper is below 0.02 percent in the finished pellet.

Jan 1, 1968

By J. L. Huiatt

The U.S. Bureau of Mines and Great Salt Lake Minerals and Chemical Corp. developed a froth flotation process for concentrating potassium salts from Great Salt Lake solar evaporites containing about 5 percent K. The crude evaporites, which were predominately halite (NaCl) with smaller amounts of kainite (KCl.MgSO4.2.7H20) and schoenite (K2SO4MgSO4.6H20), were conditioned in a saturated brine solution, thus converting nonfloatable kainite to the floatable mineral schoenite. Schoenite was then selectively floated with a medium-molecular weight fatty acid. Continuous small-scale pilot plant testing indicated that 80 percent of the potassium could be recovered from the crude evaporites in flotation concentrates assaying about 11 percent K.

Jan 1, 1975

By S. Pastor, S. Hahn

"As the concept of autonomous haulage systems (AHS) moves from proto-types to production-ready applications, the operating performance of the haul road will become ‘mission critical’ to the overall success of autonomy in mining. Deterioration in road performance will require remediation, human intervention and significant, albeit temporary, changes to operating procedures, to accommodate road maintenance. With autonomous trucks comes the opportunity to reduce road formation and operating width, and therefore generating potentially significantly reductions in stripping ratios and improvements to mine economics, but only if the design of the road, and it’s associated deterioration rate, is predictable and manageable, based both on the materials used to construct the road and the maintenance interventions to be carried out on the road. This paper presents the assessment of a digital photogrammetric approach to the characterization of a mine haul road surfacing, or wearing course material. Design and maintenance parameters for these roads are currently determined from physical particle size distribution (PSD) assessments of ‘in-road’ material. However, this approach does not accommodate the need, nor leverage the benefits from, AHS. The digital imaging approach is assessed in this paper, using two standard digital analysis software tools, together with in-service mine haul road wearing course samples and images which are assessed to determine the applicability and reliability of the approach to deliver a real-time assessment of haul road surfacing conditions and thus to identify the road maintenance interventions required to address deterioration. INTRODUCTION Enhancements in mine road design, construction and management for the past 20 or more years has largely been focused on short-term tactical needs. These improvements have not been matched by advances in the fundamental technologies that underpin mine road design and management, and although the quality of mine roads have probably increased, many of fundamental and longer-term issues have yet to be addressed. With AHS’s evolving from prototype to production applications, any decision to implement these systems in a mine requires a thorough evaluation of impacts, not only operational improvements, but the inter-connectivity of this autonomy technology to other organizational processes. In developing an understanding, the full interactions that may affect autonomous truck behaviour due to changes in various sub-systems or external environments, haul road conditions and operating performance is a key consideration. This is as true in autonomous as well as in conventional mine truck-based hauling systems where the mine haul road network is a critical and vital component of the production process."

Jan 1, 2015

By A. Röttger, W. Theisen, J. Küpferle, M. Alber

"Wear of TBM tools significantly affects tunneling advance rates. Wear-prediction models are based (amongst others) on the abrasivity of the present geology, which is determined via laboratory tests. To evaluate the results from such tests in context, this work considers the tribological system TBM tool from a materials technology perspective. In so doing, the microstructures of different application-oriented materials are presented and discussed in terms of their wear behavior and wear resistance. The significant influence of tool materials on the abrasivity of the geology and thus wear prediction models has already be identified. LCPC, Cerchar and nano-scratch experiments have been performed as confirmation. Material-dependent wear mechanisms and their correlation in terms of tunneling have shown that it is mandatory to consider the complete tribological system to estimate the wear of TBM tools. 1 INTRODUCTION Mechanized tunneling is vital to ensure necessary infrastructure development in megacities like Tokyo (Bay Tunnel), Istanbul (Eurasia Tunnel) and Mexico City (Tunnel Emisor Oriente). The use of Tunnel Boring Machines (TBMs) has been established for many years. In contrast to other methods such as boring and blasting or excavation using dredgers, tunneling with TBMs allows simultaneous excavation and removal of both the mineral and tunnel lining by tubbing segments or shotcrete. This makes tunneling more efficient, allowing for faster development of the tunnel in both hard rock and soil [1]. When budgeting such tunneling projects, precise planning and coordination in terms of tunneling technique choice (e.g. EPB or Slurry-shield), the relevant geology, and the associated penetration rates and tool wear are required. In particular, wear to TBM tools has a significant impact on tunneling progress. Due to wear, tools become dulled or lose their functionality because of brittle material behavior, thus reducing penetration rates and therefore tunneling efficiency [1]. As a result, additional tool changes are necessary, leading to higher overall costs due to down times and maintenance costs. Therefore, there is strong interest in a reliable and precise wear prediction model for TBMs. As already mentioned, the geology and associated wear of the tunneling tools define the maintenance times."

Jan 1, 2016

By C. F. Johnson

Nearly all of the sulphur produced in the world today is converted to sulphuric acid and 49 % is used in the manufacture of fertilizers. In the last few years we have seen the beginning of another chapter in the volatile history of sulphur as the severe shortage of 1963:-67 has been transformed into present-day surplus. Prospects for further aggravation of this situation in the years ahead seem assured. In 1970, western world production showed a rate of increase of 4 -5%, which 1S somewhat less than that of 8% for the period 1963-1967. The rate of growth of consumption dropped considerably in 1968 when the demands of the fertilizer industry fell. During the same period of time, wide-spread demands have been set in motion for a clean environment which indicates that a fundamental change in sulphur supply, demand, and even sources, is likely to result from this upheaval. The sale of sulphur by Poland to the western world has increased and for 1970 was estimated at over one million metric tons. In the next few years, increase in Canadian sulphur supply will stern from two sources;

Jan 1, 1972

By Michael N. Greeley

The movement to reclaim abandoned mine sites has gained momentum as federal, state, and private organizations have increased their commitment and resources to tackle mutual, and often controversial, problems of health and safety. Numerous interorganizational agreements have been implemented to promote cooperation in the characterization of mine site hazards, development of mutually acceptable plans of remediation, and sharing of actual cleanup requirements. Working through these partnerships, the federal land management agencies have begun to focus on abandoned mine reclamation in selected, priority watersheds and other drainage basins. Although there are major difficulties to overcome, significant progress continues to be made.

Jan 1, 1999

By R. G. Hite, R. G. Rowe

The Crandon deposit, located in northern Wisconsin, is a 65.8 million ton Precambrian volcanogenic massive sulfide deposit which averages 1.4% copper and 5.8% zinc. The deposit is classic in origin, mineralogy and shape. Comprehensive understanding of the geology of both the deposit and the project site has been fundamental to the credibility and success of project feasibility studies and regulatory permit preparation. Mine development in the current investment and regulatory climate requires thorough and timely application of geologic tools. From 1977-1980 geologic activities were focused on the typical objectives of orebody delineation, reserve estimation, depositional geology, and general site investigation. Results from these programs formed the basis for the project's preliminary feasibility studies. Since 1981 further geologic investigations have provided criteria for project design, site management, and operational permitting. Activities have included mine entry position definition drilling, devel reserve modeling, large diameter (150 mm) core drilling for mill pilot samples, rock mechanics testing, and evaluation of the glacial overburden/deposit geohydrology for computer simulation.

Jan 1, 1992

By Harry Leslie Bullock

With silica making up more than 27% of the earth's crust, its oxides amounting to more than 59% of the igneous rocks and quartz the most prevalent of the main free oxides, it follows that the mining engineer' is in constant contact with quartz, mainly as a gangue material to be removed as completely and economically as possible and sometimes as a valuable mineral to be purified' for the chemical,, ceramic or glass industries. Water scarcity under desert or semi-arid conditions, dwindling water supplies and difficulties of wet waste disposal in many locations and trouble from freezing in arctic locations make dry benefication more and more desirable. Advances made during the last few years in apparatus and methods and a steadily increasing knowledge of solid state physics are widening the field open to the economical application of electrostatic separation.

Jan 1, 1967

By E. Fidler

A recent headline in the Wall Street Journal declared, "trendy management schemes very often fail." Many of the management techniques addressed in the accompanying article are associated with quality management including reengineering, benchmarking, total quality management, and employee empowerment. The article made the point that executives, employees, and customers who are involved in such programs rate the effectiveness of these programs very low, and the programs often fail. Yet, we all know of companies that have made significant advances in their operations using these same quality management practices. Why do a few succeed while many fail? History has shown that the companies that successfully carry out quality management programs have two things in common: 1) Strong leadership committed to the success of the program. 2) A comprehensive plan for carrying out and maintaining the program. Stated another way -the reason many companies fail is the lack of committed leaders and inadequate planning. It is ironic that the title of the Wall Street Journal article is "The Best Laid Plans."

Jan 1, 1994

By Jodi Banta

In an effort to reverse the trend of declining enrollments to mining engineering programs that began in 2015, the University of Arizona has implemented a number of interventions over the past five years, including ramping up its pre-college mining education and outreach, and undertaking several enrollment research projects. This article is the second of two installments to discuss the results of our latest study. The first part can be found in the September 2025 issue of Mining Engineering magazine. To better understand mining’s competitive position, the School of Mining Engineering and Mineral Resources conducted a comprehensive study to determine: 1. How prospective college students, parents and educators perceive the industry, related careers and the mining engineering degree. 2. Factors affecting students’ choices of degrees and career plans. 3. The roles parents and educators play and how they influence students.

Nov 1, 2025

By R. W. Chadwick

Coal was discovered in South Africa in the mid 1830's. The earliest exploitation of modern times was probably in Natal where, in a letter dated 20 August 1842, a Captain Smith mentions that a wagonload of coal brought to Pietermaritzburg, was sold. Until the discovery of diamonds in 1867 and the Witwatersrand gold in 1886, coal mining satisfied a very small domestic demand. By 1889, at least four collieries were operating in the Middelburg-Witbank district, some 120 kilometres East of Johannesburg, and mining had star- ted at Vereeniging, about 50 kilometres to the South of Johannesburg. A map of South Africa is shown in Figure 1 and an enlargement of the main coal mining areas in Figure 2.

Jan 1, 1982

By Philip-Mark Spanidis, Christos Roumpos, Francis Pavloudakis

This paper presents a quantitative research (QNR) methodology, collaboratively conducted with a group of mining experts, to assess the knowledge management (KM) landscape in the Greek mining industry. The methodology involves a framework for structured data collection using questionnaires, statistical analysis, discussion on critical methodological aspects, and interpretation of results focusing on key aspects of interest for designers of KM systems. The paper concludes by summarizing the methodology’s outcome and proposing perspectives for further research.

Aug 1, 2024

In this paper, we present design and implementation details of a fuzzy-behavior-based controller for an automated excavator. This robotic excavator must be equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered from bucket mounted force sensors during the excavation process. Implementation details and experimental results using the fuzzy behavior based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining excavator controller.

Jan 1, 1996

By D. Suarez

The work of engineers responsible for the design and performance of mine facilities is often challenged by economic and practical constraints in the field. Problems have developed in implementing design criteria dictated by persons or agencies not familiar with the dynamic nature of mine engineering. Regional and site-specific conditions frequently require changes to standard designs, or the use of a completely innovative approach, which is not provided for in the regulations. The implementation of engineering design, therefore, usually requires a hard-sell approach to management and regulatory agencies that allows for a happy-medium to all parties concerned. Flexibility on the part of the regulatory agencies is needed to solve operational and environmental problems with sound engineering. Typical hydrologic issues which will be discussed fall in the following general categories: ? Design criteria for sizing water control structures (i.e., culverts, diversion and sedimentation ponds, ditches, etc.) ? Implementation (construction and operation) difficulties ? Regulatory compliance ? Reclamation planning with hydrologic considerations ? Protection of groundwater resources

Jan 1, 1986

By Ramazan Comakli, Cemal Balci, Nuh Bilgin, Hanifi Copur, Can Polat, Deniz Tumac

"Application of mechanical excavators for rock excavation in both civil construction and mining engineering fields has increased significantly in recent years. Prediction of the excavation performance of any mechanical excavators – tunnel boring machines, roadheaders, impact hammers, continuous miners and shearers for any geological formation is one of the main concerns in determining the economics of a mechanized mining and/or tunneling operation. A new portable linear rock cutting (PLCM) device was developed in the Mining Engineering Department of Istanbul Technical University and supported by The Scientific and Technological Research Council of Turkey (TUBITAK-112M859). The PLCM is used for cutting small core or block rock samples by a real-life mini disc cutter. The results from the PLCM are compared with the results obtained from the full scale rock cutting tests and theoretical model. It is found that there is reliable correlation between test results obtained from both cutting tests and theoretical model. 1. INTRODUCTION Mechanical excavators are currently the only alternatives to drill and blast due to higher production rate, increased safety, uniform muck size, less roof support, easier ventilation, continuous rather than cyclical operation, and possibilities for automatic control. The most of large civil tunneling and some mining projects are now carried out by mechanical excavators rather than drill and blast methods. Mechanical excavators can be categorized into two main groups: full-face and partial-face machines. Full-face machines such as tunnel boring machines excavate the face in one mode at the size of the cutterhead. Due to their cutting mode, the shape of the face profile by the full-face machines can only be circular. As for partial-face machines, the cutterhead is attached at the end of a boom. The face profile excavated by the partial-face machines can be from circular to horseshoe shape due to the cutting mode of the boom."

Jan 1, 2016

By Kot F. Unrug

When reading different studies discussing trends in coal mining, it appears that a substantial expansion of output by the year 2000 is predicted, even in the most pessimistic forecasts. Depletion of shallow, easy-to-mine deposits is only a matter of time, and the future average mining depth will increase. The proportion of slope to shaft mines operated during the next decades will change in favor of the shaft mines. Since an increasing amount of shafts in new nine developments seems to be inevitable, it appears appropriate to focus more attention on shaft design criteria. Some valuable papers have recently been published (1) that emphasize geotechnical aspects of shaft design. In the discussion that follows some other aspects of design criteria will be evaluated.

Jan 1, 1984