Search Documents

By X. Wang, Y. Luo

The propensity of coal spontaneous combustion can be evaluated using various laboratory testing methods, such as R70 adiabatic tests, thermal gravimetric analyzer (TGA) tests and critical self-heating temperature (CSHT) methods. Each of the methods has its unique characteristics and index for classifying the propensity of self-ignition of coals. Accountable relationships among the propensity indices of different methods should be established. Using the newly established R70 and TGA testing setups in our ventilation laboratory, samples from U.S. coal mines have been collected and tested. The TGA is a relatively new quantitative method. A test can be conducted in a relatively short time, within about one and a half hours, compared to the adiabatic tests. The temperature and weight of the sample can be measured with high precision and then used to determine the activation energy of the coal, which is a good indicator of the potential for self-heating. Under a specific experimental design, the TGA technique could perform the proximate analysis for determining coal quality parameters (e.g., moisture, volatile matter, fixed carbon and ash content). These parameters can be used in an empirical equation for assessing the potential for coal self-ignition. The trend of activation energies determined using TGA techniques is reasonably consistent with the trend of activation energies determined using adiabatic tests. As a case study, a comparative analysis of these two methods for determining activation energy was made on coal samples collected from Indiana. The kinetics of the spontaneous combustion mechanism has been explained. If the functional groups of a coal such as hydroxyl (-OH), carboxyl (-COOH), methyl (-CH3), etc., activate more easily with a small amount of activation energy at a relatively low temperature, the coal will have a higher potential for self-heating. With the kinetic and coal quality parameters determined by the TGA setup, it has been found that the coal with a low potential for self-ignition has low self-heating rate, a high activation energy and a high minimum self-heating temperature.

Jan 1, 2012

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with mediumsized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in the present study: a 15.2-cm (6-in.)-wide shelf; a 7.6-cm (3-in.)-wide shelf; and a 7.6-cm (3-in.)-wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1 and 1:1 were evaluated for the 15.2-cm (6-in.)-wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. IntroductionSurface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1 percent of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples).• 5.8 percent of rotary drillers were overexposed to respirable silica dust (nine out of 155 samples).• 7.3 percent of drill helpers were overexposed to respirable silica dust (three out of 41 samples).• 7.5 percent of blasters/shotfirers were overexposed to respirable silica dust (three out of 40 samples)."

Jan 5, 2018

By L. A. Arrington-Webb

The International Standards Organization (ISO) 9000 series of quality standards was published in 1987. First initiated by the British in the mid-1970's to assure the quality of British goods and services. ISO 9000 certification demonstrated the capability of a supplier to meet the requirements of the customer. Thiele Kaolin Company has invested considerable time and money achieving and maintaining ISO 9002 certification. Through a regimen of process control and documentation, routine audits, and a commitment to quality management, this kaolin producer continues to be a competitive pigment supplier in a world-wide market.

Jan 1, 1997

By Alejandro Sanz, Juan Luis Magro, David Mazeyrie

The Hampton Roads Bridge-Tunnel Expansion Project (HRBT), initiated by the Virginia Department of Transportation (VDOT), will add two new 1.5-mile TBM bored tunnels to the two existing immersed-tube tunnels between artificial islands, part of the connection between Norfolk and Hampton under the Hampton Roads Harbor in Virginia, USA. The new bored tunnels will be built by Hampton Roads Connector Partners (HRCP), a joint venture of Dragados USA, Vinci Construction, Flatiron Constructors and Dodin Campenon Bernard. This paper covers technical discussions that led HRCP to select a Variable Density TBM to address the challenges of this tunnel project, including but not limited to (i) the diameter of the bore: a 46 feet (14.04 m) diameter machine that constitutes the second-largest TBM ever used in the United States; (ii) shallow ground-cover under the water table; (iii) challenging and varying geology along the alignment, with mixed-face conditions and different types of ground modification zones; and (iv) the high TBM operating pressures required—all these and other challenges in a sensitive marine environment.

Jun 13, 2021

By J. Brune

The need for reliable and adaptable underground mine communications has become a focal point for both the safety and logistics of a mining operation. New mine communication technology aims to connect personnel, equipment, and data together while setting up a network that can be utilized during normal operations and also in an emergency event. The Mine Improvement and New Emergency Response Act of 2006 (also known as the MINER Act) requires mine operators to establish post-accident, two-way communication between underground and surface personnel and electronic tracking for all mine personnel. Communications systems must be designed such that they can survive major mine accidents, including explosions, fires, inundations and ground falls. Typical, wire-bound communication technologies are vulnerable because wires are often destroyed in such accidents. Wireless technologies that work well on the surface, such as cellular telephone networks; have limited applicability underground because the wireless signals do not propagate through rock.

Feb 23, 2014

By D. F. Strong

Most Newfoundland. mineral deposits can be clearly classified as within rocks formed either as accreting plate margins (ophiolitic pyrite-chalcopyrite massive sulfides such as Betts Cove, Whalesback, York Harbour, chromite at Lewis Hills, and asbestos at Baie Verte), at consuming plate margins (Kuroko-type polymetallic massive sulfides such as Buchans and Pilleys Island, porphyry-type Mo-Cu at Rencontre, fluorite at St. Lawrence), or within plates (zinc deposits at Daniels Harbour, sedimentary iron ores at Wabana, manganese in Conception Bay.) As these metallogenic patterns can be convincingly extrapolated southward into the Appalachians and northward to the Caledonides, they provide an important means of eliminating and selecting areas for particular exploration targets. Sonic criteria are described for the recognition of these environments of differing economic potential.

Jan 1, 1973

By B. W. Cavender

Innovative mining and metallurgical operating techniques or processes can be identified and developed by systematically analyzing change as it occurs within the mine, plant, technology, or industry. Sources of change to be monitored for innovative opportunities include unexpected successes or failures, incongruities between perceived and actual events, process needs, changes in perceptions, and the development of new knowledge. Innovation can be effectively organized, practiced, and managed. The perception of change as an opportunity rather than a threat is mandatory, as is the systematic measurement of innovative performance. Innovation is enhanced by specifically-designed policies regarding organizational structure and staffing, daily management practices, and compensation and incentives.

Jan 1, 1994

By C. P. Lazzara, R. W. Pro, A. C. Smith

The U.S. Bureau of Mines conducted a study to evaluate the effectiveness of automatic water sprinkler systems in the extinguishment of incipient conveyor belt fires under ventilated conditions. Large-scale experiments were conducted using a double strand conveyor belt configuration. Standard response, pendent-type sprinklers, with activation temperatures of 100°C, were installed above and between the two strands of belting, in accordance with Federal standards for sprinkler system installations in belt drive areas. Experiments at airflows of 1.1 and 4.6 m/s showed that the sprinklers activated later, the peak heat release rate was larger, and more betting was consumed at the higher airflow. In experiments with 74°C, fast response, directional sprinklers, the sprinklers activated at the same heat release rate for both high and low airflows, but the peak heat release rate and amount of bett consumed was slightly higher at the lower airflow. Experiments were also conducted with 100 °C, standard pendent sprinklers installed above the top belt, in accordance with the National Fire Protection Association (NFPA) Standard 123 for sprinkler system installations in conveyor belt drive areas in underground coal mines. In these experiments, the heat release rate and amount of betting consumed was larger at the higher airflow.

Jan 1, 1995

By J. D. Vincent

The Henderson mine site is located at Red Mountain on the eastern slope of the Rocky Mountains, approximately 50 miles west of Denver, Colorado. The mill site is on the west slope of the Rockies and mine and mill will be connected by an underground railroad. All designs were for a 30,000 ton per day molybdenite processing plant with provisions for future expansion up to 50,000 ton per day if required. This plan did not just happen, but slowly evolved over the course of about three and one-half years. Many plants cannot afford such a delay, but the Henderson project will take about 10 years from the time it was first discovered until production starts, and these 3 !1 years were well spent in determining the best possible plant site and flowsheet. This paper describes some of the problems and the decisions made in arriving at the final location and flowsheet. The paper does not go into the specific details of how protection of the environment went hand-in-hand with all other project considerations. This particular aspect of the planning has been well-reported on other occasions and considerable information on it is readily available.

Jan 1, 1972

By M. Rossi

The use of service variables in geostatistics (grade-thickness) is common in industry when developing block grade models and geologic resource estimates. This is particularly true in the case of sedimentary and strata-bound-type deposits. The approach has proven merits when assessing ore reserves. However, there are cases where its application for preliminary data analysis produces biased estimates. One such case is encountered in uranium disequilibrium studies. This paper demonstrates the inadequacy of service variables when performing uranium disequilibrium studies. Disequilibrium analysis is a necessary pre-processing step when radiation counts are used as raw data to calculate uranium reserves. Typically, a probe is used to obtain the gamma counts from open drill holes. These counts are then regressed (and corrected) against chemical assays obtained from core samples. During this process, the grade-thickness variable produces an optimistic image of the relationship between probe grades and chemical (true) grades, causing overestimation of the final geologic resource. The problem is analyzed through a case study.

Jan 1, 1991

By J. S. Lewis

Beneficiation and physical and chemical processing of non-terrestrial materials borrow strongly from terrestrial experience, but also involve the necessity of handling literally un-Earthly feedstocks, reagents, and environmental conditions. The present state of scientific and engineering understanding of the processing of non-terrestrial minerals, gases and hydrocarbons is reviewed with the production of rocket propellants, life-support fluids, structural metals, and refractories as the goal.

Jan 1, 1992

By James R. Jones

The Surface Mining Control & Reclamation Act is a complex piece of legislation signed into law on August 3, 1977. It is the culmination of more than six years of debate by the Congress over the need for a national regulation of surface mining as opposed to the prior concept of regulation by each concerned state. It departs from the more normal type of law in that it includes very specific requirements, limitations and performance standards. In its procedural aspects, it is somewhat similar to the Clean Air Act and the Water Pollution Control Act in that it places primary responsibility at the state level, provided the state meets minimum national requirements. At the time of writing this paper, in late December 1978, the Interim Regulatory Program has been in effect for seven months. The proposed regulations for the Permanent Program, the draft Environmental Impact Statement, and the draft Regulatory (Economic) Analysis ware available for eight weeks before the close of the comment period on November 27. We are now awaiting issuance of the final versions of these documents. The states in which coal is mined, for the most part, have made sere revision to their state laws and are in the process of revising their regulations, or have just completed the revision, to comply with the Initial Regulatory Procedures. They are now faced with another new major effort to analyze and plan for compliance with the Permanent Regulatory Program, which is expected to be promulgated by the Office of Surface Mining of the Department of Interior by the time this paper is presented.

Jan 1, 1979

By William Lodding

Unlike most ore minerals, the raw materials for lightweight-aggregate, such as clays and shales are abundant everywhere. In view of this ample choice, what are the reasons for many plant failures attributed to the raw material? How can we arrive at a proper choice of the raw material, the proper processing method for the chosen material, predict its behaviour in a plant and the properties of the final product? Determine the uniformity of the raw material and possible harmful impurities? One basic choice is sintered versus kiln-fired aggregate. It will be based on market preferences and availability of the raw material. Almost in every case a good raw material for one process is poison for the other.

Jan 1, 1964

By Ritika Kundu, Moussa Wone, Amanda M. Morgan, Tatiana K. Proctor

The Piney Branch CSO 049 Storage Tunnel (PBST) will be the last major project for the DC Clean Rivers Program. The project includes construction of a 2,200-foot-long, 18-foot-internal-diameter storage tunnel; two connections to combined sewer infrastructure; and two shafts. Major challenges include excavation underneath an existing live outfall that must remain in service; excavation of the tunnel through several areas of low rock cover and mixed-face conditions; and negotiations with a variety of federal, regional, and local stakeholders to address project impacts. This paper describes the overall project scope; geotechnical conditions along the alignment; design and construction challenges; and construction procurement.

Jun 23, 2024

By Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jennica L. Bellanca

Accidents involving powered haulage and mobile equipment such as haul trucks often account for the greatest number of fatalities in the mining industry each year. Despite previous analyses that have identified root causes and other contributing factors, there is still a need to better understand the events leading up to these types of accidents, what lessons may be learned, and what strategies can be employed to prevent fatal accidents from occurring. This study examines Naturalistic Decision Making (NDM) using the critical decision method (CDM). The CDM is a retrospective interview approach used to explore timelimited, high-stakes, decision-making. In this study the CDM is used to obtain more information about what happens prior to, during, and after a potentially fatal situation such as a near-miss event, loss of control, or minor accident involving equipment damage. Researchers captured firsthand accounts from 21 haul truck operators involved in near-miss events from mine sites of various sizes and commodities throughout the United States. These accounts provide rich and detailed narratives from the perspective of haul truck operators themselves and reveal insights into what decisions haul truck operators make, what sensory cues they perceive, and what strategies they employ during challenging and non-routine situations. Decision-related themes that emerged from the data are presented and discussed. These results, along with potential solutions offered by study participants, can help to inform future research, raise awareness about hidden hazards, and build more creative interventions and realistic training scenarios for use by the industry to address haul truck safety issues.

Feb 1, 2024

By Dennis Ofiara, Paul Zick

Two 8.2 m diameter flood control tunnels are being constructed in the Taylor Shale Formation beneath San Antonio, Texas. These tunnels use precast concrete segments as final lining. This paper describes the features of the segments chosen for this project. The tunnels are being excavated with a hybrid Tunnel Boring Machine. This paper also describes the features of the TBM which make the machine compatible to the type of segments chosen.

Jan 1, 1989

By R. E. Mitchell

Environmental Impact Assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another evaluation system becoming increasingly more common for proposed projects is the Environmental, Social and Health Impact Assessment (ESHIA). An ESHIA differs from an EIA for its more comprehensive and inclusive approach to evaluate potential impacts on public health, and its ecosystem services approach to assessing biodiversity impacts. An ESHIA may also be required by certain lenders for financing major projects. Conducting an ESHIA for a proposed mining development is not without its challenges, with costs, scheduling, regulatory concordance and other constraints to be considered. This paper examines some benefits and challenges of ESHIAs and summarizes lessons learned using a case study approach.

Jan 1, 2012

By K. E. Harrison

Acid rain legislation as proposed by President Bush [1], if enacted, will immediately refocus current thinking on the economic decision-making as related to coal preparation facilities. Unit operations currently ignored because of their costs, will become mandatory to coal plant designers and operators to ensure maximum energy recovery and sulfur reduction in the entire coal stream. In anticipation of this need, the U.S. Department of Energy, The Ohio Coal Development Office, EPRI and others are sponsoring research in several areas of coal preparation, and coal plant designers are beginning to consider more innovative techniques as they configure their flowsheets for plants of the future. Preparation plants then will have recleaning

Jan 1, 1990

By Michelle Pienaar, Musa S. D. Manzi, Thabang Kgarume, Glen T. Nwaila, Raymond J. Durrheim, Abrie Oberholster, Hennie Grobler

The South African Mining, Extraction, Research, Development and Innovation (SAMERDI) strategy was launched in 2019 with the goal of modernizing the mining industry. It comprises three major research initiatives: improvement in the efficiency of extraction and health and safety in current mining operations, development of fully mechanized systems to mine narrow tabular ore bodies in hard rock, and development of extraction systems to break rock without using explosives. The crosscutting Advanced Orebody Knowledge (AOK) program seeks to develop and implement drilling and geophysical technologies that can characterize the rock mass ahead of mining and identify potentially hazardous geological features. This knowledge will be integrated with information derived from seismic monitoring. Mining methods, layouts and rock support systems will be adjusted accordingly to mitigate the risk of rockbursts. Boreholes are routinely drilled ahead of mine workings using diamond-impregnated bits. The drill core is logged to identify lithology and geological structures (especially dykes and faults that may be seismogenic), sample the ore body for grade control, and detect areas that may contain water and/or flammable gas. Methods and technology to improve the efficiency of drilling and maximize the information obtained from the drilling process, borehole core, and the borehole itself are being investigated. A range of geophysical technologies are being developed to map the rock mass from the skin of the excavation to a distance of several tens of meters. Light Detection and Ranging (LiDAR) is used to map the geometry of the excavation, including prominent joint, vein and fracture sets and the presence and performance of rock support elements and systems. Ground Penetrating Radar (GPR) is used to penetrate deeper into the rock mass and image joints, fractures bedding planes that influence the stability of the hanging and side walls. Image processing techniques known as ‘seismic attributes’ are being applied to the radargrams to improve interpretation. Electrical Resistivity Tomography (ERT) and various active and passive seismic techniques (e.g. Tunnel Seismic Profiling (TSP), ambient noise tomography) achieve even greater penetration into the rock mass. Finally, machine learning is used to improve the processing and interpretation of seismic and radar data.

Apr 26, 2022

By P. N. Eksteen, G. E. Greig

The South African mining industry currently installs about 6 km per month of plastic pipes for conveying compressed air and water. Plastic pipes have a number of desirable properties and are favoured by many mining engineers because of their low mass, which facilitates ease of erection and assembly, and their excellent corrosion resistance and durability. However, they are combustible, and if involved in an underground fire can contribute to the overall toxicity of the combustion gases emitted. Furthermore, plastic pipes have the potential to conduct a fire from one part of a mine to another, and, by so doing, exacerbate an already hazardous situation. The limitations of small scale tests and the need to establish a large facility where underground conditions could be simulated was recognized by the South African mining industry. This paper briefly describes the Industry's full scale fire test facility and presents the conclusions drawn as a result of a number of full scale combustibility tests conducted on pipes manufactured from unplasticized Poly Vinyl Chloride (uPVC) and High Density Polyethylene (HDPE). Based on these findings, some practical solutions to prevent the spread of fire along the length of pipe columns of various pipe diameters and suspension configurations are presented. Recently some new and exciting developments in the field of intumescent coatings have occurred which are proving effective in minimizing the incidence of fire underground on South African mines. The potential benefits of these coatings are briefly discussed. INTRODUCTION Plastic pipes used underground on mines are predominantly in the form of protective cladding on insulated chilled water pipes and as service pipes for the conveying of water and compressed air to the workings. Plastic pipes have found wide use in the aggressive environmental conditions encountered underground due to their favourable properties relative to steel; these include being lightweight, easily installed and virtually immune to corrosion. However, plastic pipes are inherently combustible and can contribute to the overall hazard in three ways: (i) they are easily ignitable and can provide the initial fuel for a fire. (ii) once ignited, they can propagate a fire along their length and by so doing ignite other combustibles in their path, thereby contributing significantly to the overall conflagration. (iii) they can contribute to the overall heat, smoke and toxic gas emissions from a fire. While conscious of the value of small scale fire tests, the South African mining industry recognized the need for full scale testing to determine the combustion characteristics of plastic pipes under conditions closely approximating those underground and, as a consequence, a full scale fire tunnel test facility was commissioned with the objective of being able to (a), accurately evaluate the potential hazard of the various types of the plastic pipes found in mines, (b) use this information to suggest suitable fire engineering practices to minimize the hazard and (c), to practically verify the efficacy of the practices suggested. THE FIRE TUNNEL The fire tunnel is situated on a mine in the Western Transvaal and is 40 m long with a cross section of 3 m x 3 m which is typical of many haulages currently in use in South African gold mines. The ventilation drawn through the tunnel is provided by a 110 kW centrifugal exhaust fan and air velocities can be varied from 0 to a maximum of 5,8 m/s.

Jan 1, 1993