Search Documents

"The Ohio River Bridge East End Crossing Tunnel requires a 75-year service life of its cast-in-place reinforced concrete lining. This twin-tube 3-lane (each tube) highway tunnel is about 55-ft wide and 30-ft high. Since unified tunnel service life prediction methodology does not exist in the US, challenges occurred during the design-build phase of this project. These challenges include the methodologies in determining the reinforced concrete’s degradation mode, the lining’s surface chloride concentration level, the reinforcing steel’s critical chloride threshold value for corrosion, how to verify the concrete’s diffusion coefficient, and the durability impact from concrete crack width. This paper presents a methodology in verifying the proposed concrete mix can achieve the service life requirements. This methodology can be adopted for service life prediction for future tunnels to be built in the US. INTRODUCTION The Ohio River Bridge East End Crossing (ORBEE) Tunnel is part of a Public Private Partnership project, which connects transportation network between Louisville, Kentucky and southern Indiana. Located in Louisville, Kentucky, the twin-tube highway tunnel provides northbound and southbound lanes of the Kentucky approach to a new bridge across the Ohio River. Tunnel lengths are approximately 1,675-ft and 1,685 for the northbound tube and the southbound tube, respectively. Connected by two cross-passages, both tubes have a roadway width of 40-ft, for 3-lane traffic, and a vertical clearance of 26.5-ft.The tunnel was constructed by drill and blast method with shotcrete and rock dowels as initial ground supports. The final tunnel lining system includes: •,Nominal 16” cast-in-place reinforced concrete lining, with 2” and 3” concrete covers over reinforcing steel for its extrados and intrados, respectively. •,20” cast-in-place reinforced concrete invert slab, with 4” and 3” concrete covers over reinforcing steel on its top face and bottom face, respectively. •,PVC waterproofing system around tunnel perimeter, excluding invert slab. •,Perforated PVC groundwater collection pipes on both sides of the tubes and one below the invert slab of each tube."

Jan 1, 2016

By F. L. Pirkle, W. C. Bagby

"In his 1989 book, The New Realities, Peter F. Drucker, Clark Professor of Social Science at Claremont Graduate School, Claremont, CA, stated: “Information is data endowed with relevance and purpose. Converting data into information thus requires knowledge. And knowledge, by definition, is specialized” (p. 209).The discipline of mineral valuation is knowledge-based and requires a mineral valuer to collect, analyze and interpret data that are material to a mineral-valuation assignment. In so doing, the valuer turns the data into information (data come first, followed by information as determined by the mineral valuer) for use by the client (from whom the valuer obtained the mineral-valuation assignment) and other intended users. The valuer uses his or her experience and education (each valuer’s knowledge base) supported by a foundation built upon competency, materiality and transparency, the three pillars of mineral valuation (minerals valuation, mineral-property valuation).The International Mineral Valuation Standards Template (IMVAL Template), third edition dated May 2018, defines mineral valuation as: “The estimation of the value of a mineral property in money or monetary equivalent. The word ‘valuation’ can be used to refer to the estimated value (the valuation conclusion) or to refer to the preparation of the estimated value (the act of valuing)” (p. 14).Furthermore, the IMVAL Template clearly separates valuation from evaluation: “The template deals with valuation, which is distinct from evaluation. The distinction inherent in these defined terms is that valuation addresses the estimation of value of a mineral property, whereas evaluation addresses the broader assessment of a mineral property for an investment decision (p. 2).”This is an important difference because the minerals industry commonly makes investment decisions using feasibility studies to evaluate a proposed mineral development and production project. The purpose of such investment-decision analysis is distinctly different from valuation of a mineral property, no matter where that property lies upon the mineral explorationdevelopment- production-reclamation timeline (Fig. 1). Valuation involves terms such as market value, just compensation, fair value, etc., whereas investment-decision analysis is concerned with the economic viability of a given proposed project. Although feasibility analysis and market valuation can both use discounted cash flow (DCF) analysis as a tool, the formulation of the DCFs and their interpretation are different."

Nov 1, 2019

By Erik Sundström, Magnus Nygren

Having seen significant improvements to accident rates in the last 40 years, companies in the Swedish mining industry now show a greater focus on the development of safety cultures throughout their organisations and workplaces. However, there is a lack of research examining the different safety initiatives and strategies practiced in the industry today. This study explores the potential influence and consequences such initiatives may have on the development of safety cultures in the Swedish mining industry. Twelve interviews with experts on safety initiatives from four different Swedish mining organisations were conducted and analysed in a process based on qualitative thematic analysis to identify notable connections to safety culture development. The results of these interviews highlight proclivities in the implementation and use of safety initiatives such as subjects of focus, methods and desired effects. This enables the interpretation of the conceptualisation and methods for the development of safety culture in these organisations based on their approaches to safety development. We believe the results of this study can serve as support for discussions on safety culture development in the Swedish mining industry, and be of interest for international mining industries, in addition to approaches to research in this field. However, we also believe it is important to emphasise the opportunities to approach safety culture in mining from different perspectives than those common today.

Jul 19, 2023

By R. H. Sergent

The interest in using halogens for extracting precious metals from ores has increased due to changes In ore characteristics, environmental concerns and regulations. The rediscovery of halogen leaching capability has been the topic of these and other writers1-30. Much work has been done on the performance of bromine, chlorine and iodine5-29. Of these, bromine and chlorine look most promising. Iodine is quite expensive and sometimes forms an Insoluble film on a precious metal surface22,23. Little experimental work has been published on the relative performance of bromine versus chlorine. The Pourbaix diagrams for the halide leach system (see Fig. 1-4) Indicates a significant stability advantage for bromine In forming complex ions with gold. This should result In greater extraction of gold under similar leach conditions and Is evaluated In this work. The regeneration of halogen from a spent leech solution is a critical requirement for an environmentally acceptable halogen leach process. Bromide can be oxidized In-situ to bromine ~ adding chlorine or ozone2,31. Bromide like chloride can be oxidized In an electrochemical cell to produce halogen on demand 13,15,17. Bromine clearly offers a number of possible regeneration pathways. This work strives to compare the relative ability of chlorine and bromine to extract gold from partially and fully oxidized ores. A commercially pressure oxidized sample was evaluated under a number of experimental conditions. The autoclave feed ore from the same mill was also evaluated after complete oxidation In a laboratory autoclave.

Jan 1, 1993

By R. Hendrickson

In the 1940's a top blown water-cooled oxygen lance was developed to inject oxygen into liquid iron. This process, the LD or BOF process technique, today is used in 65% of the world's steel production, and represents the largest oxygen market for temperature enhancement in steel and non-ferrous smelting applications. There are three major approaches to the use of oxygen in metallurgical processes: (1) general enrichment of the air supplied to burners or tuyeres, (2) under-flame enrichment or injection, and (3) the use of an auxiliary oxy-fuel burner as a heat source. With each of these techniques there are technical and economic trade-offs.

Jan 1, 1990

By G. T. Lineberry

The Work Crew Performance Model (WCPM) is a method for designing, implementing, and evaluating? performance improvement strategies for machine operators and other mining personnel. The WCPM offers a practical approach for measuring job proficiency and identifying costly behaviors. It enables interventions aimed at performance improvement, especially training, to be assessed monetarily. Two interrelated elements of the WCPM are emphasized: observational techniques for establishing performance baselines and measuring performance outcomes and cost linkages between job competencies and measures related to profitability. Inter-and intra-subject differences in performance-related behaviors of regular and incidental shuttle car operators were detected during field validation of the WCPM. Downtime data were used as outcome measures to test linkages between performance error rates and cost consequences. Use of a simulation program for analyzing continuous mining face operations showed how common shuttle car operating parameters (e.g., payload, tram rate) can be used as cost-conscious indicators of performance variability and therefore as targets for performance improvement.

Jan 1, 1994

By K. V. Raj

"The development and advancement of computational fluid dynamics (CFD) has made it possible to better understand pollutant flow and distribution in deep open pit mines. Open pits located at higher latitudes, especially in the Arctic and sub-Arctic, face a unique problem due to atmospheric temperature inversion, which is prevalent during much of the winter. A three-dimensional CFD model of an actual open pit mine in the Arctic was developed to analyze the problem of pollutant growth during inversion, and mitigation of the pollutants through improved ventilation schemes. Due to the availability of mine-specific data, such as contaminant concentrations and coordinates of sampling locations, the actual 2013 pit geometry was used for model validation Concentrations predicted by the selected realizable ?-e turbulent model are compared to measured pollutant concentrations at the open pit. Pollutant concentrations at selected locations showed differences, but remained within the same order of magnitude in most cases. INTRODUCTION Computational fluid dynamics (CFD) has emerged as a useful tool for ventilation modeling in underground mines (Edwards and Hwang 1999, Purushotham and Bandopadhyay 2009, Wala et al. 1998, Xu et al. 2011). Application of CFD in open pit mines has been limited, however, since most open pit mines located at lower latitudes do not encounter considerable ventilation problems. Open pits located at higher latitudes, especially the Arctic and sub-Arctic, face a unique problem due to atmospheric temperature inversion, which is prevalent during winter. A number of Russian researchers have tried to understand the air inversion and resulting pollutant transport problem by modeling air flow phenomena in open pit mines (Baklanov and Burman 1996, Baklanov 1984, Baklanov 1995, Belousov 1985, 1989, 1995). Much of their work, however, was based on numerical models and methods of finite difference. Baklanov (2000) applied a modified ?-e and a ?-l CFD model to air flow phenomena on various terrains. More recently, Choudhury (2011) used the COMSOL CFD package for modeling pollutant transport for an idealized open pit mine. Collingwood et al. (2012a, 2012b) used a two-dimensional model for fluid flow and contaminant transport at an Arctic open pit mine. The authors have also previously presented work on CFD modeling of an actual open pit mine at high latitude (Bandopadhyay et al. 2014, Raj et al. 2015a). However, the CFD work done by the above-cited researchers lacked model validation with field-measured data. Validation of a developed model is important in assessing the quality and accuracy of the predicted results. In general, experiments are done numerous times in controlled environments to assess the validity of collected data. There are two types of assessments used in CFD simulations: (1) verification and (2) validation. Model verification is checking the accuracy of the computer codes during the implementation phase of a real-world problem, within the specific limits of accuracy (Oberkampf and Trucano 2002). Since, the pollution transport model presented in this paper used the commercial ANSYS-FLUENT CFD package, verification is not needed as the program has been tested widely, and verified numerous times."

Jan 1, 2016

By Paul R. Wieber

This paper describes the U. S. Energy Research and Development Administration's (ERDA) program to develop in situ coal conversion processes, especially gasification, he potential of this technology, the technical directions being explored, and the program strategy to carry the process concepts toward commercialization are emphasized. The geographic location of the U. S. coal resources and a market analysis are described. Commercially successful in situ coal processes could add over a trillion tons of coal to the U. S. coal reserves. The economics of these processes is compared with surface gasification independent studies show this process to be 25Z cheaper than surface gasification for Western coals. The major projects are briefly described. The Linked Vertical Well process is in the lost advanced stage and shows great promise. The last test produced a low-Btu gas averaging 171 Btu per standard cubic foot for average pro¬duction rates of 5.5 million standard cubic feet per day. The other projects are Packed Bed, Longwall Generator, and Steeply Dipping Beds.

Jan 1, 1977

By Sean Peterfreund, Grant Finn, Ty Jahn

For urban underground development involving tieback anchors for excavation support, authorities having jurisdiction typically require tiebacks to be de-tensioned before project completion. This paper updates “A Proactive Approach to Tieback Anchor De-tensioning” (by Peterfreund and Finn, published in the 2017 RETC Proceedings), which discussed a new method employed in a cut-and-cover transit station project. Since publication of that paper, 237 tiebacks were successfully and rapidly detensioned from using a small-diameter drill to cut strands from the surface. To the authors’ knowledge, this was the first intentional large-scale use of a drilling method for this purpose.

Jun 13, 2023

By T. Brozell

"Communities near sand mines and processing facilities in Wisconsin have raised concerns regarding possible exposure to ambient respirable (PM4) crystalline silica. Fenceline PM4 (particulate matter captured with a 50 percent cut size of 4 micrometers aerodynamic diameter) crystalline silica concentration data were compiled at Fairmount Santrol Inc., Mathy Construction Inc. and U.S. Silica facilities. The long-term average PM4 crystalline silica concentrations ranged from 0.05 to 0.45 micrograms/m3 when sample values below the limit of quantification were treated as zeros. All of the long-term average concentrations were less than 20 percent of the Minnesota Department of Health’s and California Office of Environmental Health Hazard Assessment’s PM4 crystalline silica chronic reference exposure level of 3.0 micrograms/m3. The measured concentrations were consistently within the local background concentration range.Air Control Techniques P.C. compiled the sampling data using Thermo Fisher Scientific Inc. Partisol 2000i PM2.5 samplers meeting the requirements of 40 CFR Part 50, Appendix L. These samplers were adapted to capture particulate matter with a 50 percent cut size of 4 micrometers. The use of polyvinyl chloride filters allowed for crystalline silica X-ray diffraction analysis by NIOSH Method 7500. The combined use of adjusted PM2.5 filter-based samplers with Method 7500 crystalline silica analyses provided for a highly sensitive limit of quantification of 0.31 micrograms/m3 of PM4 crystalline silica.BackgroundIn 2005, the California Office of Environmental Health Hazard Assessment (OEHHA, 2005) adopted a 70-year chronic reference exposure level (REL) for PM4 (particulate matter having aerodynamic diameter of 4 micrometers or less) crystalline silica. The REL was extrapolated from occupational hygiene epidemiological studies, essentially all of which were based on in-plant PM4 crystalline silica measurements. No well-established ambient sampling technique for PM4 crystalline silica was available at the time that OEHHA adopted its REL. The personal samplers used for the National Institute for Occupational Safety and Health (NIOSH) Method 0600 in-plant sampling of employee exposure were designed for concentrations higher than ambient levels. The limit of quantification (LOQ) of PM4 crystalline silica on NIOSH 0600 filters was too high for the effective sampling of ambient air."

Jan 1, 2015

By Zach Ahinga, Mike McRae, Dave Hopkins, Steve Klein

The San Vicente Pipeline project involves the construction of an 8-1/2 foot diameter water pipeline in an 11 mile long tunnel in San Diego, California. The tunnel will be excavated in extremely variable geologic conditions consisting of strong granitic and metamorphic rocks, weak sedimentary rocks, abrasive conglomerates, and mixed face conditions. This paper discusses the challenging geologic conditions and some of the key design evaluations for the project. Currently design work for the project has been completed and construction will be underway by mid-2005.

Jan 1, 2005

By Steve Kral

"Each January, tunneling and underground professionals gather in New York City for the George A. Fox Conference. The one-day event offers attendees the opportunity to listen to their peers outline what’s new in the underground construction industry, get updates on major projects in North America and have a chance to catch up of old friends.The conference is put on by the Underground Construction Association of SME. This latest conference attracted about 370 specialists in the industry. The theme for this year’s event was “Water Tunnels, Past, Present and Future.”The technical session included talks focused on major tunneling projects, including the massive California Water Fix program and the Massachusetts Water Resources Authority (MWRA) Metropolitan tunnel redundance program in Boston. The conference also included an update on the Gateway Project from Phil Rice from WSP and Mahammed Nasim of Amtrak as well as a Tunnel Industry update.The following is a sample of a few of the presentations. Technical presentationsDEP’s Tunneling Program Evolution. James Mueller is the agency chief engineer of New York City’s Department of Environmental Protection (DEP). Its mission is to plan sustainable infrastructure investments for the future of clean water and the environment in the city and its watersheds, he said. The agency’s goals are to synthesize information across bureaus within DEP to allow data-driven decision-making. It is also to optimize internal agency processes and systems related to the implmenation of engineering programs within a structured assessment process. The agency also prioritizes projects and funding within a structured integrated planning process. And it standardizes project performance and delivery to meet the needs of the agency in alignment with industry standards and market capabilities."

Mar 1, 2019

By Herman Gill, Dani Delaloye, Madelyn Rubin

The Foothill Tunnel is a remote 16-mile-long untreated drinking water tunnel in the San Francisco Public Utilities Commission’s (SFPUC) Hetch Hetchy Water and Power (HHWP) system. The 14-foot horseshoe shaped tunnel, constructed in the 1920s, is lined intermittently with concrete over approximately 53% of its length, with the balance being unlined rock. After detailed planning, in January of 2020 Mott MacDonald and HHWP staff completed a visual inspection and documented the condition of the tunnel with electronic data collection, photographs, and video with audio recording. The result was a comprehensive condition assessment that identified key areas of the tunnel to monitor.

Jun 13, 2021

By Jim Clark

Tunnel boring machine (TBM) tunneling is an ever-increasing prospect for underground construction, and, with each new tunnel bored, there are unknown elements. When boring through the earth, even extensive geotechnical baseline reports can miss fault lines, water inflows, squeezing ground, rock bursting and other types of extreme conditions. This article draws on the consider-able field service experience within Robbins to analyze successful methods of dealing with the most challenging conditions encountered. Many tunnel projects are located in areas with relatively poor access along the tunnel alignment and bored under extremely high overburden. These two factors often result in limited geological information. It would be reason-able to state that the deeper the tunnel, the greater the lev-el of uncertainties. When faced with these uncertainties everyone involved with the project including the owner, the contractor and the machine supplier must be prepared to tackle geological surprises. This article describes the problematic geological conditions and associated difficulties faced on three separate projects and the measures that were taken to overcome these difficulties.

By J. H. van Laar, C. S. L. Schutte, M. Le Roux

Highly energy-intensive systems prone to wastage are significant causes of unnecessary energy losses in industry. Deep-level mine chilled water reticulation systems fall within this category of inefficient energy-intensive systems. Some techniques (measured baselining, zero-waste baselining, leak detection, and control valves) exist to identify and reduce wastage in mine water reticulation systems. However, these techniques have not been compared, which begs the question of which is more accurate. A need, therefore, exists to compare these methods to determine the effectiveness of each. This study investigates each method and applies them to a case study mine, providing a platform for comparison. These methods identified wastage ranging between 2 and 20 l/s (3–30% of water consumption). The comparative effectiveness of the methods from best to worst was found to be zero-waste baselining, leak detection, control valves, then measure baselining. This study proposes an application procedure combining the considered methods to identify and eliminate wastage on deep-level mine systems more efficiently.

Jan 31, 2024

By Rick Wright, Gregory L. Raines

San Diego’s need to access underground space has dictated a long history of tunnel construction. The subsequent need for water, coupled with San Diego’s natural attractiveness, has led to significant population increases and the need for the construction of even more tunnels. This paper will provide a historical summary of the progression of mines, tunnels and trenchless technology construction projects that contributed to the advance of current technology, feasibility, and constructability. A bibliography of relevant reports and data is included.

Jan 1, 2001

By Georgene Renner

With more than 800 booth spaces sold and 540 exhibiting companies displaying their wares, there was something for everyone on the exhibit floor of the 2014 SME Annual Meeting in Salt Lake City, UT Feb. 23-26. The following is a sample of what was offered at the 2014 meeting.

By JOHN HOMER, Jacob L. Carr, Jonathan K. Hrica, Kathleen M. Stabryla, Iman Benbourenane, Jennica L. Bellanca

Given the recent focus on powered haulage incidents within the US mining sector, an appraisal of collision avoidance/warning systems (CXSs) through the lens of the available research literature is timely. This paper describes a rapid review that identifies, characterizes, and classifies the research literature to evaluate the maturity of CXS technology through the application of a Technology Readiness Assessment. Systematic search methods were applied to three electronic databases, and relevant articles were identified through the application of inclusion and exclusion criteria. Sixty-four articles from 2000 to 2020 met these criteria and were categorized into seven CXS technology categories. Review and assessment of the articles indicates that much of the literature-based evidence for CXS technology lies within lower levels of maturity (i.e., components and prototypes tested under laboratory conditions and in relevant environments). However, less evidence exists for CXS technology at higher levels of maturity (i.e., complete systems evaluated within operational environments) despite the existence of commercial products in the marketplace. This lack of evidence at higher maturity levels within the scientific literature highlights the need for systematic peer-reviewed research to evaluate the performance of CXS technologies and demonstrate the efficacy of prototypes or commercial products, which could be fostered by more collaboration between academia, research institutions, manufacturers, and mining companies. Additionally, results of the review reveal that most of the literature relevant to CXS technologies is focused on vehicle-to-vehicle interactions. However, this contrasts with haul truck fatal accident statistics that indicate that most haul truck fatal accidents are due to vehicle-to-environment interactions (e.g., traveling through a berm). Lastly, the relatively small amount of literature and segmented nature of the included studies suggests that there is a need for incremental progress or more stepwise research that would facilitate the improvement of CXS technologies over time. This progression over time could be achieved through continued long-term interest and support for CXS technology research.

Jun 17, 2022

By N. Paas

Diesel powered equipment has been operated in underground coal for more than 50 years. According to the Mine Safety and Health Administration (MSHA), there are approximately 3,000 diesel units operating in underground coal mines in the United States. This number is expected to reach 5,000 diesel units in 250 coal mines by the year 2000. Also, there are approximately 5,000 diesel units operating in metal/nonmetal mines such as trona, potash and salt mines: and more than 3,000 diesel units operating in Canada. This increased popularity of diesel powered equipment over trolley wire, electric trailing cable or battery powered equipment is because of improved safety, greater mobility, higher productivity and increased power of diesel equipment.

Jan 1, 1997

By James M. Barker

Industrial minerals are critical to most aspects of modern society. They are pervasive in both industry and in everyone's lives (McVey, 1989; Barsotti, 1993). They are also the dominant class of minerals produced in the United States but this fact is little known outside the industry. For example, in 1993 (U.S. Bureau of Mines, 1995, table 1) industrial mineral dollar value was double that of metals ($20.86 billion vs. $10.88 billion) and employment levels were nearly so (74,000 vs. 40,000). A further difference is that transportation tends to dominate production costs (FOB end user) whereas they are much less significant in other mining ventures or other industries. Finally, metal mines are more concentrated west of the Mississippi; industrial mineral operations are more prevalent to the east (U.S. Bureau of Mines, 1995, p. 16-17). The significance of transport cost is discussed in Part 2, which is essentially Barker and Austin, 1995. Part 1 will update and expand portions of Barker and Austin (1995) and provide a more detailed discussion of import/export relationships using a China/United States reference point because of China's dramatic influence on some industrial mineral markets since the mid-1980s (barite, etc.).

Jan 1, 1996