Search Documents

By W. R. Peters

An experimental hole-to-hole seismic probe system has been developed for use in coal measure geology as a means of determining the structural conditions of coal seams. The source probe produces a 500-joule electric arc discharge whose seismic wavelet has a spectrum in the 200 to 2,000 Hz frequency range. Low compliance hydrophones contained in the source probe as well as in a separate seismic detector probe are matched to the frequency range of the source. Both probes are constructed with 5-72 cm diameter housings. The transducers in the probes are equipped with fluid-inflatable boots to permit operation in either wet or dry boreholes. Preliminary tests in vertical boreholes drilled 213 m apart in sedimentary rock formations show reliable operation and useful seismic propagation measurements along horizontal and oblique paths up to 232 m in length. Because the seismic wave- let has an accurately repeatable waveshape, multiple shots and signal averaging techniques can be used to enhance the signal-to-noise ratio and extend the transmission distances.

Jan 1, 1985

By Morgan M. Sears

The LaModel program is widely used to calculate stresses and displacements on thin tabular deposits, particularly when multiple seams or complex mining geometry is encountered. The program itself allows the user to create multiple mining steps to show a progressive sequence of mining. However, LaModel considers each individual step as an independent steady-state condition, and any previous loading conditions of the materials are not tracked. It also does not consider any sort of dynamic stress change during the mining process. In certain circumstances, especially in multiple-seam situations, modeling a scenario of the seam of interest without considering the previous mining sequence in the off seams can potentially lead to inaccurate results. The primary objective of this paper is to present a situation where a potentially dynamic, unstable mining condition was encountered. It was not evident until the previous loading conditions in the off seams and the impact of dynamic stress changes in the active seam were considered. It is important to make the mining community aware of these potential modeling scenarios where the path-dependent nature of the mining sequence is of key importance. This paper presents a case history where room-and-pillar retreat mining was being conducted in a relatively deep cover stress regime where multiple seam interactions were present from both undermining and overmining. Mining in the active seam was being conducted with roomand- pillar mining techniques consisting of a series of parallel production panels being successively developed and retreat mined along a set of Mains. In this situation, the traditional global LaModel analysis without any path-dependent adjustments did not fully identify the area of poor conditions that were encountered. This paper explores the impacts of mining in the active seam on the lower seam which, in turn, has a negative impact on the active seam. This provided a solid foundation for the subsequent analysis of the three seams simultaneously. Based on the calibrated model, it is likely that retreat mining in the active seam resulted in increased stresses in the underlying seam that conceivably resulted in additional convergence and, most likely, additionally convergence of the pillars under the panel being developed. This in turn could have caused active subsid- The LaModel program is extremely useful for analyzing multiple-seam mining scenarios. As multiple-seam situations become even more prevalent, the potential for encountering a path-dependent mining scenario also increases. To successfully model path-dependent mining scenarios, the ground control engineer will be required to make sound judgments on the condition of pillars in sub-adjacent seams. These engineering judgments should be based not only on the current state of stress, but also on any prior or future states of stress. This means considering the stresses from over or undermining as well as stresses applied to the sub-adjacent seams from actively mining the seam of interest.

Jun 25, 2024

By J. E. Friant

The Mini-Disc TM cutter drill bit is a radical design departure from the traditional tri-cone rock drill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-Disc TM drill bit, referred to as the "Disc Bit" has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory cannot shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By R. J. Morlock

Prior to 1912, coal research for Republic Steel, Corporation was limited to a periodic box test conducted in a commercial coke oven. Then in 1912, a Koppers movable-wall test oven was -built to research wall pressures for selected blends and to conduct other varied research work. In the 1950's economic pressures caused a reassessment of position resulting in the establishment of a Coal and Coal Chemical research group in 1956. In 1958 this group, along with other groups of research endeavor were incorporated into the new Republic Steel Corporation Research Center at Independence¬ Ohio. Currently this section is divided into four groups. 1) Coal Preparation, 2) Coal-Chemicals, 3) Coal Characterization, and 4) Coal Carbonization. The objective of each group is described, and a brief listing of the work done under the first three groups is indicated. A more detailed description of the studies by the Coal Carbonization group of the coking characteristics of Republic Steel Corporation's coals as blended among themselves or in conjunction with selected purchased coals follows. The wall pressure, contraction, and stability index criteria are specified, and the method of assessing these criteria as a function of blend composition is indicated.

Jan 1, 1963

By Charlie Sons

Pit and underground mine operators typically use a lot of big equipment tires. Just as typically, they spend a lot of money they shouldn't on these tires. That's because tire use and maintenance are not given enough attention. That often occurs because mine management and personnel do not know the basic facts of tire use and care. If a piece of large equipment is damaged or ruined, a good explanation better he forthcoming. A ruined tire is often just a shoulder shrug. But that sort of fatalistic acceptance can cost tens or hundreds of thousands of dollars a year extra for big equipment tires. That does not have to be. There are some basic tire considerations that, if followed, will extend tire life and lower tire costs. Most companies have the inevitable conflict between the production department, which resists any restrictions that may reduce productivity, and the maintenance department. Production success is based on meeting a schedule of yards moved, while maintenance success is based on availability and equipment cost. When production falls behind schedule and equipment speeds are increased, maintenance may soon find its tire costs rapidly increasing, unless everyone understands the tires' vulnerability to damage. Unless the production department understands the problem, or restraint is applied by top management, costs may become exorbitant. At one job site, tire costs alone exceeded $250,000, to move 55 dam3 (72 000 yd3) of dirt on an 11-km cycle. The operation temporarily caught up with its schedule, but tire costs and attendant downtime soon made this a not-for-profit exercise. Because an operator must always attempt to move payload at the lowest cost, there are cases when higher than normal tire costs must be accepted. For example, in pioneering work with tandem engine scrapers, steep grades shorten tire life to less than normal. But the steep grades make shorter haul cycles possible, yielding more trips per hour than alternative earth-moving methods.

Jan 1, 1982

By R. Spears, J. B. Vincent, S. Donald, J. Litaker

Previous efforts to remove and concentrate heavy-metal ions from wastewater streams via metalloprotein affinity metal chromatography (MAMC) were limited to the metal transport protein transferrin. Extension of the technique to the enzymes carbonic anhydrase and carboxypeptidase A, which possess different metal affinity properties, is described. Preliminary results indicate that the technique is capable of selectively removing and separating late first-row transition metal ions from aqueous solution. The results suggest that by properly choosing the matrix, i.e., protein or enzyme, MAMC may he applicable to problems involving a wide range of heavy-metal-hearing aqueous solutions.

Jan 1, 1996

By R. C. Karra

Mining is one of the oldest profession and second after agriculture. Unfortunately Mining is not so familiar in the society. Due to lack of recognition in the society, existence of mines in remote places and in dusty and humid working conditions, led the poor response for mining engineering. Mining engineering programs have been increasingly less attractive to the student population over the years due to negative image of mining industry. After graduating in mining engineering, there is not much problem of employment at present. In the last 10 to 15years most of the mining engineering graduates have joined software industry. Even those joined in mining industry also left with in 2 years of service. The main reason for this is not being satisfied with job, it is not only working conditions but also work environment, work culture, remote location of the mines etc. Though many were trying to leave mining profession, the recent economic slow down has prompted some of them to incline towards job safety and retained to mining job. At this juncture a systematic study was taken up to analyze the job satisfaction of mining engineers in India.

Jan 1, 2011

By David L. Bradfield

This paper covers the development of the Yeelirrie Uranium Project from the discovery of the Yeelirrie deposit in 1970 to the present time, with emphasis on the mining, processing, and environmental requirements of the project. The Yeelirrie Uranium Project is managed by the "Yeelirrie Uranium Joint Venture Partnership", which, when formed, consisted of Yeelirrie Development Company Pty., Ltd., Urangesellschaft, Australia Pty. Ltd. and Esso Exploration and Production Australia Inc. The Yeelirrie Uranium Joint Venture Partnership holds mineral claims over the Yeelirrie uranium ore deposit in Western Australia. This deposit encompasses some 35 million tonnes of ore containing in excess of 50,000 tonnes of uranium as U308. Agreement has been reached with the State of Western Australia to mine and process the ore to produce uranium ore concentrate. The Project scope provides for an open-cut mine, alkaline leach hydrometallurgy plant, power plant, township, airstrip, access roads, community services and utilities. The Yeelirrie Uranium Project described herein has progressed through the stages of exploration, mine evaluation, process testing, project scope definition, environmental approval, Pilot Plant operation, preliminary engineering and the publishing of a definitive Project Feasibility Study. This article summarizes the project development through the above stages.

Jan 1, 1984

By F. D. Wang

This paper presents an innovative mining method with the application of the water jet. The basic principle of this mining method is to mine a thin panel slice with a water jet system and to allow the roof to deflect elastically and subsequently to be supported by the coal floor without artificial roof support. Through the sequential mining of layers from top to bottom, the entire seam is extracted and the roof rests upon the mine floor. The advantages of this method are that the safety of underground operation can be greatly increased and the surface overburden disturbance will be markedly reduced. . An economic evaluation of such a system is presented for the total cost estimated per ton of coal mined at the face. This evaluation is then compared to that of a continuous mining section utilizing a room and pillar mining method.

Jan 1, 1991

By Walter E. Kramer

The advantages derived from the use of pellet burdens in blast furnaces are so great, that hematite ores are being converted into pellets in greater quantities each year. The conversion of these ores into pellets appears on the surface to be relatively simple. In reality, this is not so. Serious difficulties are encountered in drying these pellets that do not exist in the drying of taconite concentrate pellets. The ores that present problems are goethite and earthy hematites. Green pellets prepared from these ores have very law shock temperatures, 200-600° F. The shock temperature of a green pellet according to our definition is the highest initial temperature to which a green pellet may be exposed without suffering decrepitation. Decrepitation may involve spalling, fracturing or total disintegration. The poor shock properties of these green pellets result from the inability of the vaporized water to escape freely and easily as it is formed with¬out affecting the integrity of the pellet. As a consequence, the pellets must be carefully dried prior to induration. This careful treatment is costly. The slow drying process restricts productivity and requires larger furnaces than desired. The use of an additive to elevate the shock temperature of the green pellets would increase productivity. Bentonite is used in some pellet plants to improve balling but it raises the shock temperature only slightly. Nalco became interested in the shock temperature problem because of its activity in the development of organic pelletizing aids for taconite concentrates. The findings reported here are an outgrowth of our experimental work on the development of shock temperature additives.

Jan 1, 1967

By David Martin Menne

In a small tank, slurry is passed through the high shear impeller zone with small time intervals, and a large proportion is regularly exposed to air at the surface, and at relatively high shear rates. This accounts for significant differences in the performance of large and small tanks. It is preferable to derive data where possible directly from an operating plant rather than applying data generated in small tanks where allowances must be estimated for the above differences [and where slurry aging and often substantial cooling compared to hot freshly milled ore further distorts results]. Various measurements have shown that many gold slurries can suffer extreme variability, as streamers of bypassing material or boules of hold-up periodically condstitute the instantaneous discharge from a tank - the relatively high Yield stress of slurries [around 1 to 10 Pa] causes very incomplete homogenization of slurry in any tank, the worse the larger the tank and the more viscous the slurry. To provide a background for this subject, this monograph presents leach and adsorption models based on the fundamental physics and chemistry of these processes, and includes quantitative discussions of factors which can lead to deviations on scale-up. The Throughflow model which avoids the need for such alowances is then presented, as well as a Computer Programme applying this model, and which allows direct calculation of the effects of:

Jan 1, 1995

By John Jonkman

Many companies in the mining and minerals processing industry are finding themselves in the transition stage from the Industrial Age to the Information Age and are trying to become prepared for the Knowledge Age. To remain competitive in the decades ahead, they are faced with integrating the enterprise through the use of computers and networks. This paper discusses some common human and organizational barriers to enter- prise integration. It proposes how to develop the organizational and human' networks to match the capabilities of the technical networks which are being' implemented. Ten practical considerations are then presented for consideration in the executive suite in addressing the human side of implementing the computer integrated enterprise.

Jan 1, 1989

By Malcolm D. Flavel

As indicated in the introduction to this paper, it is a sequel to that which I gave to the last annual meeting in Atlanta in march. This paper goes further into aspects of crushing and screening, primarily from the standpoint of circuit control. There has been little published by equipment manufacturers on this subject and this is the first paper on crushing circuit control to be sponsored by Allis-Chalmers corporation. By proper control over the use of crushing energy, we will be able to produce finished products from feed materials uti¬lizing minimum capital for the lowest cost of production. The subject will be discussed as follows. Firstly, we will look briefly at what we are trying to accomplish; Secondly, what is presently available in the way of technology; Thirdly, we will look at a suggested new system of control which will best fit the parameters of the normal crushing and screening operation; As a conclusion, I will summarize the advantages of the new system.

Jan 1, 1977

By D. H. Dvorak

Two pilot-scale biological reactor systems were installed to treat metal-contaminated water. The reactors consisted of barrels and tanks filled with spent mushroom compost, within which bacterial sulfate reduction became established. Concentrations of Fe, Zn, Mn, Ni, and Cd were lowered by over 95% as these metals were precipitated as insoluble sulfides by reaction with bacterially generated H2S. The chemistry of the reactor systems is examined, and opportunities for maximizing their metal-retaining and alkalinity-generating potentials are discussed.

Jan 1, 1991

By T. Negeri, A. O. Orumwense

Microwave pretreatment is one of the emerging technologies which have been reported as having potential economic benefits for the processing of amenable ores. The application of microwave pretreatment to the processing of refractory and finely disseminated ores is of great interest as the technology can potentially reduce high comminution costs and improve mineral liberation. Sized ore samples were subjected to microwave irradiation at power levels varying from 1 to 5 kW over exposure times of between 1 and 6minutes in order to determine the influence of heating rate on mineral transformation, ground product size distribution and mineral liberation. The microwave irradiated samples were ground and subsequently floated. A comparison is made with non-microwave treated samples. Flotation grade and recovery show a strong dependence on the microwave absorption characteristics of the mineral components of the ore, in the following decreasing order -sphalerite, galena, and lastly chalcopyrite.

Jan 1, 2003

By D. P. Patil, B. K. Parekh

Water is the mainstay for beneficiation of fine size coal and minerals; however, it is also the least desirable constituent in the final product. The basic concept of the novel process described in this paper is based on the differential surface heat absorption capacity of individual particles, which differs for different species of mineral. When a mixture of fine material is exposed to a radiant energy source, the various solids components present in the mixture will absorb heat energy depending on their composition and there will be difference in the surface temperature of the particles. When this differentially heated solid mixture is placed on a moving belt, which is coated with low temperature melting resin, the hotter component of the mixture will stick to the belt and relatively cooler will stay free on the belt and fall off at the end of the belt run. Experiments were conducted with pyrite, coal and quartz of 6 x18 mesh particle size. The goal of the test program was to find the optimum conditions at which there exists a required temperature difference between minerals and coal particles by controlling the operating and system variables. Preliminary tests results showed that there is a potential for separating mineral matter from coal using the thermo-adhesive separation technique.

Mar 2, 2022

By Jonathan K. Hrica, Brianna M. Eiter

The ability to identify hazards during a workplace examination is a critical skill for mineworkers to have in order to maintain a safe workplace. While research suggests that being able to successfully recognize hazards requires a complex set of competencies, it is unclear which competencies are most critical to adequately perform a workplace examination. This paper presents a hazard recognition competencies framework as an explanation of the competencies that affect mineworker hazard recognition. To better understand how the industry is selecting and preparing workplace examiners, researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) interviewed nine health and safety (H&S) professionals at surface stone, sand and gravel mine sites throughout the United States. These interviews verified that the competencies included in the hazard recognition competencies framework agree with perceptions of the interviewed H&S professionals, who also provided validity for the critical role these competencies play. Finally, the results of this study are presented within the context of current NIOSH research findings related to hazard recognition.

By A. Geertsema

Introduction Gasification of coal has been practiced for many decades for the production of gas, fuels, chemicals and power. However it has only more recently started to get significant attention in the USA. In this review of the basics the features of gasification as compared with combustion is covered and the potential of increasing the conversion of coal via gasification is indicated. After dealing with the fundamentals of gasification a review of gasification technologies will be presented with an indication of the widespread international and more limited US use of this technology. In conclusion the attention will be directed at the future prospects of gasification.

Jan 1, 2006

By Wen L. Chen

The steam coal quality is less stringent than metallurgical coal quality. The steam coal is prepared either by cleaning full size range of raw coal or cleaning coarse coal only, leaving the fine coal raw. The latter scheme is more cost competitive. It is particularly applicable to U.S. eastern soft coal where low ash coal is concentrated in fine sizes. For raw coal size separation, a recently developed Rotating Probability Screen, developed by the British Coal Board, may be advantageously used for easy change of raw coal separating size and to avoid screen deck plugging when handling wet and clayey raw coals.

Jan 1, 1983

By J. W. Oberholzer

This paper describes research being undertaken by the Chamber of Mines Research Organization (COMRO) which is designed to assist the continuous miner operator and section foreman in the performance of their jobs. The project will initially provide visual assistance to the miner operator, and later will semi-automate the mining (cutting) process. Using a technique known as "RF tagging," the project will also provide real-time or near-real-time information about the performance of the loading and hauling units to the section foreman, allowing him to quickly detect problems and take action where appropriate. The project is based upon the application of currently available technology, and the first phase is scheduled for in-mine testing within the next year.

Jan 1, 1991