Search Documents

By Robert F. Kaufmann

INTRODUCTION In response to the Uranium Mill Tailings Radiation Control Act (Public Law 95-604, Section 114c), a report has been prepared by the U.S. Environmental Protection Agency (1980) which describes the potential health and environmental effects associated with uranium mine wastes. The author was responsible for the geology, hydrology and aqueous pathways analysis portions of the report. All potential sources of contaminants, solids, liquids, and airborne emissions, which might cause adverse impacts upon the environment or health of nearby populations were considered. Wastes at both active and inactive uranium mines (Hans and O'Connell, 1981) are described and assessed with respect to dose and health effects (Blanchard et al. 1981). The emphasis of this paper is on the liquid emissions and the aqueous pathway. Model uranium mines were developed for surface and underground mines. The model underground mine was placed in New Mexico while the model surface mine was in Wyoming. Development of a generic assessment was complicated due to the inherent variability of uranium mines. Also, most information available relates to uranium mills rather than to mines, or reported measurements were often influenced (biased) by wastes from a nearby mill and did not specifically reflect mine discharges. Consequently, the assessment presented is often based on conservatve (maximizing) assumptions which are identified as such, and which were based on knowledge from field investigations, available literature, and consultations inside and outside the U.S. Environmental Protection Agency. Maximum use was made of available data, supplemented with limited field studies in Colorado, Texas, New Mexico, and Wyoming. PREVIOUS INVESTIGATIONS Stream survey work in Colorado by the Water Pollution Control Commission and the U.S. Geological Survey (Moran, 1974; Wentz, 1974) mentioned a portion of the Uravan Mineral Belt and uranium mines therein, but the work did not emphasize uranium mines. Significant amounts of acidity and total trace metal concentrations were found in streams from 18 different mining areas. Dilution and chemical precipitation below mine drainages decreased concentration and increased the pH. Given enough time and distance, the streams recover naturally, but the accumulations of trace metals in the sediments increase. Field observations in 1971-72 of streams in most of Colorado indicated that approximately 724 km of streams in 25 different mining areas were adversely affected by mine drainage (Wentz, 1974). Discussions of the impacts of uranium mining on water quality or quantity are incidental in numerous impact statements and environmental reports prepared by industry and (or) the U.S. Nuclear Regulatory Commission as an integral part of licensing or relicensing uranium mills. Coverage on mining is usually minor as the principal focus is on milling impacts. The same is true for the recently prepared generic EIS on regulation of uranium milling (U.S. Nuclear Regulatory Commission, 1979). Radiochemical assessment of surface and groundwater in uranium mining districts of New Mexico is done by self-monitoring programs associated with NPDES permits. Also, radiochemical assessment studies have been funded by the New Mexico Environmental Improvement Division and U.S. Environmental Protection Agency. Unfortunately, there has been no concerted effort to prepare broad assessments of the cumulative impacts of mining and milling in areas of interest in Texas, New Mexico, and Wyoming. Critical review and synthesis of these types of data can produce rather useful information. For example, the publication "Water Quality Impacts of Uranium Mining and Milling Activities in the Grants Mineral Belt, New Mexico" (U.S. Environmental Protection Agency, 1975) addresses the groundwater and surface water changes as the result of extensive uranium mining and milling production in a relatively confined area. A more recent report by the Wyoming Department of Environmental Quality summarizes 16 years of aqueous radium and uranium data. The study reports significant amounts of radium-226 and uranium were present in surface water in the Shirley Basin as a result of inadequate mine water treatment (Harp, 1978). In Texas, surface water and groundwater monitoring conducted by industry, as well as by State and Federal agencies, reveals little or no change of chemical quality attributable to uranium mining and milling (Gesell, 1977; Kallus, 1976). This conclusion is based on 586 samples collected from 198 stations over a period of 39 years, but primarily from 1961 to 1975. The State monitoring program by several agencies is continuing, but data reporting and interpretation is lagging. One survey (Itin, 1975) showed that none of the mine water from the 10 lakes that were sampled was suitable for human use. The lakes were also unsuitable for irrigation due to mineralization of the water by sulfate, chloride, and TDS. One of the 10 was suitable for stock watering.

Jan 1, 1981

By A. R. Wilde

The Muruntau gold deposit is situated in the Kyzyl Kum Desert of Uzbekistan. It is currently being mined in the world's largest open pit gold mine with production believed to be of the order of two million ounces per annum. The open pit measures about 3.5 by 2.5 km and extends to a depth of 350m. The gold ore resource in the Muruntau deposit, including production, is about 170 million ounces of gold (Anonymous, 1996). This paper presents a summary of the deposit geology and its regional geological setting. Information used in this paper has been generated from observations made on two visits to the mine and its environs, and a review of the Russian-and English-language literature.

Jan 1, 1999

By Rolf Christiansson, Daniel Johansson, Urban Åkeson, Henrik Ittner, Mats Olsson

"This paper presents two recent studies on the extent of blast damage after excavation in crystalline rock. The Swedish Transport Administration and the Swedish Nuclear Fuel and Waste Management Company (SKB) are both under regulations to limit excavation damage during construction of tunnels. SKB is also required to limit the Excavation Damage Zone (EDZ), as this could be a potential flow path for radionuclides in the planned repository for spent nuclear fuel. Presented in this paper are investigations of blast damage from three tunnel sites, a road tunnel, an experimental tunnel in Äspö Hard Rock Laboratory and an underground subway depot. As expected the fractures resulting from the bottom charge are both longer and more frequent then those mapped in the column charge. The results show that the requirement to limit blast damage according to Swedish regulations was fulfilled for the column charge at the three studied sites.1 INTRODUCTION The Swedish Transport Administration (TRV) and The Swedish Nuclear Fuel and Waste Management Company (SKB) have both recently completed studies related the extent of blast damage from modern explosives after excavation. SKB studies focused on blast damage from pumpable emulsion explosives for underground construction (Ittner and Bouvin 2015) and hydraulic connectivity in the EDZ (Ericsson et al. 2015). TRV had a broader focus with different types of explosives including blasting for both road cuts and tunnelling with pumpable emulsion explosives. Investigations by means of geophysics were also conducted (Olsson et al. 2015). High demands on perimeter control and excavation damage is usually required for underground constructions with a long operation time, such as public tunnels for transport or underground repositories for nuclear waste. This paper presents the findings of recent Swedish studies and aims to discuss the topic in a broader context."

Jan 1, 2016

By Richard D. Zigmond

In this paper, a computer program that has been developed for determining the capital and operating costs for coal preparation plants is described along with its applications. The logic of the computer program is based upon the results of a survey of existing preparation plants, operators, plant contractors, equipment manufacturers, and consulting firms. This survey provided information on plant performance, order-of-magnitude costs, and costing procedures. Additionally, an extensive cost data file for the major capital equipment in coal preparation plants has been developed. Using the washability data and the computer program outputs, the cleaning costs per million Btu can be calculated. Details about the program and its applications can be found in a report by the authors (Zigmond et al., 1979).

Jan 1, 1981

By T. McNulty

The author was privileged to find employment as a uranium mill chemist for The Anaconda Company while working his way through school in the mid-1950s. He then served Anaconda in various technical and management positions until 1980. This paper describes the prevalent technologies employed by uranium producers, briefly describes various mines and mills in the U. S., and memorializes a few of the thousands of men and women who contributed to the U. S. Uranium Boom. Following isolation of uranium as an element by M. H. Klaproth in 1789, uses of uranium were confined primarily to pigments, glass coloring agents, and ceramic glazes. In 1896, Antoine Becquerel found that uranium is radioactive, releasing particles and energy as it decays. In 1898, Pierre and Marie Curie isolated radium from uranium and learned that it can be an effective treatment for some types of cancer. In 1939, it was discovered that the isotope U235 is fissionable1 . Up to this point, nearly all uranium production was from pitchblende concentrates made in Bohemia, Canada, and the Belgian Congo. In 1938, only about 5 percent (23.85 short tons) of global output was produced from ores of the carnotite mineral that were being mined in the U.S. By the early-1950s, physicists in many countries had begun to recognize the potential for nuclear chain reactions. Ernest Rutherford (UK), Frederick Soddy (UK), and Leo Szilard (US) explained transmutation of elements and formulated the principle of “atom splitting”. In 1934, Marie Curie’s daughter, Irène, and her husband, Frédéric Joliot, identified uranium as the most viable source for this new form of energy. The basic fission process was unraveled by German scientists in December 1938. After Hitler’s army seized the uranium deposits in Czechoslovakia, many feared that Germany would build the first nuclear weapon.

Mar 2, 2022

By M. Pérez-Tello

A mathematical model to represent the expansion and fragmentation of copper matte particles oxidized under flash converting conditions is presented. The model assumes that the particles are initially nonporous, have a constant mass prior to fragmentation and travel at a constant velocity throughout the reaction chamber. The model requires the specification of the following five parameters: the particle expansion rate, a fragmentation diameter factor, a fragmentation size distribution parameter and the fractions of the finest and the coarsest particles in the feed that undergo fragmentation. The model predictions show good agreement with the experimental data collected in a laboratory furnace over a wide range of experimental conditions. The evolution of the size distribution of the particles along the reactor length was computed, and the model parameters were correlated with the experimental operating variables. Model predictions indicate that particle residence time is an important factor in the generation of dust. The presence of two maxima in the particle density function may be attributed to turbulent conditions prevailing in the furnace, which cause particles to follow different trajectories within the furnace even if they are injected at the same location.

Jan 1, 2008

By R. J. Sweigard, T. Beckman, C. T. Justice, E. D. Thompson, T. C. Hopkins

As a means of permanent disposal, fine coal refuse is often pumped as a slurry into surface impoundments. As the available volume is filled, the embankment heights are frequently increased. The additional embankment material is often placed upon consolidated fine coal refuse. There has been concern about the long-term effect of consolidation of this material at or above the liquid limit on its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from central Appalachian coal-preparation plants. The refuse was consolidated in 3-m (10 ft) Plexiglas columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart, and triaxial tests were performed on both the consolidated and unconsolidated material for comparison of their shear-strength parameters.

Jan 1, 1998

By S. J. Porter, M. T. McRae

The new tunnel at Genting Sempah is part of a privately funded infrastructure projectthat involves duplicating the existing highway extending from the Gombok Toll Plaza near Kuala Lumpur to Karak, in Malaysia. The 60 km long tollway includes an 800 m long, two-lane highway tunnel with excavated dimensions of 10.5 m wide by 8 m high. The majority of the tunnel extends through slightly to moderately weathered, moderately to highly jointed quartz porphyry. Excavation of the tunnel was performed using drill and blast methods and the primary tunnel support consists of rock dowels and shotcrete except for short sections adjacent to the portals where steel sets were utilized. A portion of the tunnel encountered sheared and altered material that was successfully supported using rock dowels and shotcrete. The final lining for the tunnel consists of mesh and fiber reinforced shotcrete. The flexible nature of the primary support and shotcrete final lining resulted in considerable cost savings and expedient construction methods.

Jan 1, 1997

By Lynne Chastain

The Eastern Shoshone and Northern Arapaho tribes of the Wind River Indian Reservation, Wyoming are interested in developing their industrial mineral resources. The U.S. Bureau of Indian Affairs (BIA), Division of Energy and Mineral Resources (DEMR) is assisting the tribes in evaluating the potential of their industrial mineral prospects for development. Gypsum occurs on both sides of the Owl Creek Mountains in the basal portion of the Jurassic Gypsum Springs Formation. The gypsum resources that are being evaluated crop out along the northern flank of the Owl Creek Mountains in the Sweetwater basin, a small topographic sub-basin of the Big Horn Basin. From October 1998, to April 1999, DEMR personnel mapped, sampled, and drilled the southcentral butte within the Sweetwater basin. Samples were analyzed for free and combined water, and major mineral oxides to determine gypsum purity. Gypsum purity averaged 93.6 percent for surface samples and 95.1 percent for drill core samples. The basal portion of the Gypsum Springs Formation is comprised of several beds of gypsum up to 9 feet (2.7 m) thick separated by 0.5 to 2.0 foot (0.15 to 0.61 m) thick lenses of siltstone and limestone. Overall gypsum in the formation ranges from 35 to 90 feet (11 to 27 m) in thickness. A resource of approximately 7 million short tons (st) (6.4 million metric tons [mt]) has been identified.

Jan 1, 2001

The administration came on as a strong supporter of the mining industry in April of 1982 when President Reagan delivered his long-awaited minerals policy statement. He promised to reduce America's minerals vulnerability, and called for spending billions on meeting stockpile goals for strategic minerals, opening up federal lands for mineral exploration, elimination of barriers to deep sea mining, and regulatory relief. He defended the favorable tax incentives in the Economic Recovery Act as a stimulus to private research and development that would ensure the availability of materials essential to the nation's economy and national defense. But the administration just didn't seem to get anywhere. Congress, environmentalists, and even foreign governments fought White House-proposed legislation on all fronts, delivering the ultimate coup in forcing Environmental Protection Agency Administrator Anne Burford's resignation and the subsequent EPA staff house cleaning in early 1983. Anti-Reaganites scored victory after victory against Reagan's efforts to stimulate the minerals industry. Congress was stalemated on so many mining-related issues that not much was done either for or against the industry. And the US was not to get its way on the issue of sea mining either. Most of Reagan's mineral policy objectives failed to be met. Three months after the National Materials and Minerals Program Plan was presented and the Cabinet Council on Natural Resources and the Environment was made its coordinator, the head of the Cabinet Council James Watt blamed lack of progress in reviving the mining industry and creating a better strategic stockpile on the weak economy and the House of Representatives, which repeatedly thwarted efforts to open wilderness lands to mining. Congress The 97th Congress spent much of its time saying no in 1982-to the Reagan administration's deep cuts in energy and environment programs, to major changes in clean air and water laws, to oil and gas leasing in wilderness, and to killing the Department of Energy. Most of 1982 (and 1981) was spent in heated budget disputes. Some things that did not happen: • The administration and industry failed to get changes in controls of hazardous air pollutants and sulfur dioxide emissions that are implicated in the phenomenon known as acid rain. Industry had wanted to relax requirements for new industries building in clean air regions where the air act demands prevention of significant deterioration (PSD) of air quality, and to relax requirements tightening up the regulation of emissions of hazardous air pollutants. The air battle is expected to continue on five major fronts-acid rain, hazardous air pollutants, PSD, automobile pollution, and nonattainment. • Regulatory reform legislation to overhaul the way government carries out the law died a slow death last year. Business groups and the administration said federal agencies should be required to consider cost-effective measures of reaching regulatory objectives of protecting public health, safety, and the environment. Opponents, including environmentalists, feared such action would delay, weaken, or scuttle important regulations. • Congress turned thumbs down several times on proposals for oil and gas leasing in wilderness but could not agree on any new wilderness recommendations (see The Wilderness Battle). • Congress refused to open the door to the Reagan administration's plan to raise up to $4 billion a year from sales of federal lands. The administration identified surplus and excess federal lands, mostly obsolete buildings or isolated tracts of land, that could be sold by the General Services Administration (GSA) to help out the federal budget deficit. Congress took no action. Some things that did happen: • Congress extended the Defense Production Act (DPA) for six months through March 1983 without changing the 32-year-old law. That came after it failed to resolve sharp differences over proposals for critical minerals programs. Differences concerned both the amount of funds and the scope of programs that would be authorized under the DPA's Title III. Some proponents pressed for $5 billion in funding for loan guarantees or purchase commitments to spur domestic production of minerals such as cobalt. Other members of Congress wanted smaller amounts of funding, and the Reagan administration, until about November, had opposed any use of federal funds for strategic mineral programs. These measures were certain to come up again before the DPA extension expired in March. • House supporters of the Critical Materials Act of 1982 were unable to come up with the twothirds majority needed to pass the bill, so it died on the House floor in December. The bill proposed that a council be established with responsibility for coordinating federal materials research and development. The administration opposed the council creation contending that the Cabinet Council

Jan 5, 1983

By M. E. Breitrick

Newmont Gold Company began full production in early 1995 at the Carlin East underground mine. The mine is currently producing at the rate of 900 tpd (1.000 stpd). for an annual production of 150.000 ounces. Approximately one hundred twenty five hourly and salary personnel are employed at the project for the estimated six-year mine life. Two mining methods are currently utilized at the mine. Longhole stoping with cemented backfill accounts for 70% of the total mine production. Conventional underhand drift and cemented fill accounts for the balance of the daily tonnage. In December 1996. Newmont purchased a new AC-Eickhoff ET-210 Roadheader. The machine went into service in mid-June of 1997 and is used in both longhole stope topcut development and cut and fill production at a rate of 225 tpd (250 stpd). The Carlin East mine is operated by Newmont Gold Company. The mine is one of four underground gold mines in production in northeastern Nevada owned by Newmont Gold.

Jan 1, 1998

By W. A. Haley

As far back as 1939 state laws have required reclamation of mined lands. Reclamation has been the topic of many discussions and presentations, especially since the late 1960's. In the past ten years many states have added legislation concerning the reclamation of coal-mined lands. In the near future, it seems certain that some federal regulations will be passed that will set minimum guidelines for the states to regulate. Besides the requirement of returning the land to the approximate original contour, future regulations will more than likely demand replacing topsoil from one to five feet thick. As regulations become more stringent, costs will rise accordingly. Since no one has developed a machine that can do all reclamation work by itself, it is necessary to review in detail the tools available and to select the most economical means.

Jan 1, 1976

By Michael Schultz, Gregory Sanders

In 2017, the North Texas Municipal Water District (NTMWD) initiated the design of the Sister Grove Regional Water Resource Recovery Facility (SGRWRRF) to provide additional treatment capacity for future population growth within the Lavon Lake watershed. To provide a discharge location for SGRWRRF approximately 4.5 miles of 2.4- meter (96-inch) internal diameter pipeline will be constructed, including 2.3-kilometer (7,800) feet and 487-meter (1,600 foot) long tunnel segments. This paper will discuss the anticipated geology of the two tunnel segments, selection of the tunnel alignment, the anticipated initial tunnel support requirements and other aspects of the project design

Jun 13, 2021

By F. G. Miller

In mid-1972 we determined that a fresh approach to coal mining research was needed for the industry as well as for Bethlehem. The reasons to us were obvious: Productivity was in the throes of a steady decline, and labor and maintenance costs were spiraling upward. Yet, despite this predicament, nowhere in the U.S. at that time was there a comprehensive and coordinated research and development plan in the offing. The Bureau of Mines had not yet been charged with such a responsibility, and industry was content to rely on machinery manufacturers for innovations. After studying our own mining practices, the state-of-the-art of mining research elsewhere, and development work by manufacturers, we presented a comprehensive research package to our management at the end of 1972. The ideas and experience of many operating and management personnel in our Corporation contributed to the formulation of the final plan as approved.

Jan 1, 1976

By Raymond E. Langen

Uranium exploration in the Powder River Basin of northeastern Wyoming has been intensive since 1966 and in 1968 produced significant discoveries of reduced uranium ore by Humble Oil & Refining Company and others. Substantial reserves have been established in the area. High-grade carnotite ore was discovered in 1951 near Pumpkin Buttes in the central part of the basin (Fig. 1). Other mineralized areas were soon established from Pumpkin Buttes south to Monument Hill and Box Creek. Total production from these shallow oxidized deposits in the lower Eocene Wasatch formation was small. The AEC reports total production of 520,000 tons of ore averaging 0.19% U3O8. The authors are indebted to many people within Humble Oil & Refining Company and Esso Production Research Company for their assistance and guidance. SUMMARY AND CONCLUSIONS The Highland ore deposit, discovered in 1968, is a large uranium occurrence located in the southern part of the Powder River Basin. Uranium mineralization consists of sooty, black uraninite and coffinite coating sand grains and is concentrated along the margins of Tertiary fluvial sandstones. Uranium was transported by oxidizing solutions roving through the buried sandstones and spreading into less permeable channel-edge sandstones to form typical rolls and tabular deposits. Unaltered sandstones are light gray to gray-buff where the sandstones have been oxidized, the colors are various shades of red, yellow, and yellowish brown. An Oligocene tuffaceous source for the uranium is proposed; however, leaching of the arkosic and tuffaceous host sediments may also have provided a source.

Jan 1, 1971

NICOR Mineral Ventures, Inc. retained Neyer, Tiseo and Hindo, Ltd. to evaluate the potential effects of a planned dewatering operation at NICOR's proposed, 258-acre silica sand mining facility near South Rockwood, Michigan. The ?orebody? is a horizontally extensive, friable, quartz sandstone from the Sylvania Formation which also serves as an aquifer for some of the rural, residential development near the site. We conducted an aquifer test on the site which identified the important aquifer properties. Using these data and an analytical model, we determined that the radius of influence would be expected to range up to 6000 feet from the quarry during its final development stage. An inventory of water supply wells revealed that most wells had sufficient available drawdown and would not be adversely affected. A long-term groundwater monitoring program was recommended to monitor the possible effects at some of the closest wells.

Jan 1, 1987

By R. C. Guimareãs

Serrana's deposit contains three types of ore: oxidized, micaceous and silicate-carbonate. The results presented refer to characterization and fundamental studies performed on fractions resulting from the purification of five samples from the silicate-carbonate type collected in the mine. Each type was purified and submitted to mineralogical characterization, zeta potential determinations, and microflotation experiments. The samples, with exception of the barite, are mineralogically complex and the selectivity between apatite and gangue minerals is poor. Under the current state of art, it is impossible to feed the plant with the silicate-carbonate ore, unless it is blended with the standard oxidized ore.

Jan 1, 2002

By M. T. Ityokumbul

The use of yield index, the product of the yield and gangue rejection, for the optimization of separation processes is presented. The characteristics of the yield index are contrasted with separation efficiency calculations and applied to laboratory froth flotation and washability data. Data from continuous froth flotation tests conducted to "optimize" froth flotation using process optimization software were also evaluated with the yield index procedure.

Jan 1, 1997

By R. Todd Swinderman

Variations in designs between belt cleaner systems are so wide that it is impractical to establish a dimensional stan- dard. The number of variables that affect the efficiency of belt cleaners is too great to assume a required number or style of cleaners for broad classifications of bulk solids or typical applications. The amount of carryback remaining on the belt is more dependent upon the characteristics of the bulk solid and the physical parameters of the conveyor system than it is on tonnage of material conveyed. Therefore, a performance-based standard is proposed. Three levels of cleaning performance are proposed: • Level I cleaning is general specified when concerns about carryback are not critical. Cleaning systems normally associated with achieving a Level I performance are single or double cleaner systems with one-piece blades undergoing poor to average maintenance. Frequent cleaning of the carryback that falls from the return run will likely be required. • Level II cleaning is generally specified when carry- back is of concern but does not create a safety or environmental problem. Cleaning systems normally associated with Level I1 performance are multiple cleaner systems with segmented blades undergoing the manufacturer's specified maintenance. Regular but infrequent cleaning of the carryback that falls from the return run will likely be required. • Level III cleaning is generally specified when con- cerns about carryback are critical. Concerns range from safety to environmental to product contamination. Cleaning systems normally associated with achieving a Level 111 performance are multiple cleaner systems in conjunction with at least one low- volume water spray. Scheduled inspection and the manufacturer's specified maintenance would have to be performed to maintain a high level of cleaning performance. Difficult-to-clean bulk materials may require the use of a washbox system with multiple cleaners using a combination of low-volume eater sprays to lubricate the cleaners and high-volume sprays to keep the washbox and discharge piping freely flowing. Further addition of a water and sludge recycling system reduces the amount of water that ends up in the product to a negligible amount. Very infrequent cleaning of the carryback that falls from the return run will be required. PURPOSE The purpose of this proposal is to propose a standard method for specifying belt cleaner systems based on user expectations and equipment performance over time. DEFINITION In bulk solids handling by conveyor belt, carryback is the material that adheres to the belt after the belt discharges its cargo. PROPOSED STANDARD Required Basic Good Practices There are a number of basic design and operating principles that are good practice for the selection, installation, and maintenance of belt cleaning systems on conveyors in order to achieve "standard belt cleaning performance over time. 1. The Belt Cleaning System shall be designed to meet the performance requirements based on the worst operating conditions and worst bulk solids proper- ties that are expected. 2. Each conveyor discharge point shall be designed to readily accept the manufacturer's recommended minimum number of belt cleaners. In addition, the discharge chute shall be designed to accept, with minor modifications, at least one additional cleaner if it is required.

Jan 1, 2004

By Hans W. Schreiber, Rudi P. Fronk

IINTRODUCTION Widespread activities in precious metal projects in the western U.S., Australia, Canada and other parts of the world have opened a flood-gate of consul- ting expertise to aid and accelerate the development process. Utilization of outside expertise has taken on many shapes and forms that have in some instances actually "decelerated" or "retarded" project progress. Small mines are especially vulnerable to apparent false-starts and misdirections, be- cause of their generally lower capital commitments, shorter lead times and limited mineral in-house expertise. Mine development for small mines requires fundamental approaches by knowledgeable consultants that are timely and cost-efficient and in line with accelerated development, if they are to be successful. The development process is obviously that process which brings a given deposit into production. Or, put another way, the process comprises all activities, decisions and commitments which take place from the moment an authorizing entity (usually a board of directors) com- mits to development and production (usually on the basis of a final feasibility study) until the first ton of ore is processed to a saleable product. The activities, decisions and commitments over a development period--such a period can range from as short as a year or less to as long as 5 years or more--are many, highly varied, and often interdependent. The development period is also particularly risky, not only because of the varied and interdependent decisions and commitments, but also because of capital demand amounts. Delays in the development process are thus particularly costly - sometimes so costly that small and often undercapitalized mining companies, failing to reach production and a cash flow within a planned period, face, if not bankruptcy, at least severe equity dilution or particularly onerous and restrictive covenants on additional loan financing. It therefor behooves especially small mining companies to examine ways to accelerate development. By doing so, the development process may actually meet planned scheduling. The development process generally comprises environmental impact studies completion, final engineering, permit- ting, financing, equipment and machinery procurement, contractor selection and construction -- such activities largely being overlapping. The paper addresses what the small mines operator or the small mining company can do with consulting firms to accelerate development. By "small mines" is meant open pit operations of 2000 tpd or less and underground operations of 500 tpd or less. By "consulting firms" is meant entities who do not possess an engineering and construction capability, such as Derry Michener Booth & Wahl, Pincock Allen & Holt, Behre Dolbear-Riverside, etc. The paper concentrates on gold projects. PRIORITY CONSIDERATIONS Of the items listed in the previous paragraph which comprise the development process, the two which most consistently appear to cause delays are permitting and financing. The former's delays can be due to political overtones and thus the delays may not be reasonably foreseeable. The latter's delays are most often due to inadequate preparation, and thus are avoidable. For the reason stated above, and considering that financing is fundamental to all of the activities which constitute the development process, the paper focuses on financing as the priority item which can most assist in accelerating or retarding the development process.

Jan 1, 1987