Search Documents

By Richard V. Good, John B. Harvey, Lloyd S. Jones

INTRODUCTION The term "Rapid Underground Excavation" is generally associated with high speed tunnel advance with large volumes of excavation, and indeed this is the type of work for which most of the recent innovations in methods and new machinery have been developed. However, the term applies as well to any underground excavation process that results in an earlier project completion than would be expected with conventional methods, and hopefully with a decrease in total unit excavation cost. Often significant progress has been made during the primary stages of an underground construction project and then an inordinate amount of time and effort has been expended on small units of "miscellaneous" excavation which has delayed the overall project completion and escallated overall unit costs. Construction at the Nevada Test Site of the Atomic Energy Commission for underground testing frequently requires significant amounts of so called "miscellaneous mining" such as short access drifts, cross cuts, alcoves, niches and concrete keyways. Many of the keyways must be excavated without disturbing the rock beyond the excavation lines and construction scheduling often dictates that much of the work must be accomplished without disturbing sensitive electronic equipment already installed. In order to cut down on lengthy and costly delays required for the tedious manual excavation of much of this miscellaneous mining, a market search was made for suitable mechanical excavation equip-

Jan 1, 1997

By K. V. Raj, R. Jacksha

Conveyor systems persist in being a source of injuries and fatalities in the mining industry. To reduce these incidents, better methods are needed to enhance the monitoring of probable hazards and improve situational awareness during the normal operation and maintenance of conveyor systems. To address these issues, researchers from the National Institute for Occupational Safety and Health (NIOSH) continue to investigate emerging technologies that show the potential to improve miner safety around conveyors. This paper presents a feasibility assessment by NIOSH researchers of a fully integrated, commercially available wireless Internet of Things (IoT) system to improve situational awareness around conveyor systems. Included are discussions of a full-scale laboratory test bed that was designed to simulate a working conveyor system as well as the challenges and successes of integrating the IoT system with the test bed.

Oct 6, 2020

By R. J. F. Goodfellow

Many underground projects now include preparation of a Risk Register through planning and design as a tool for project and risk management. There is still significant discussion within the industry as to whether and how to best present the Risk Register through the bidding process and the construction phase of a project. While the ITIG Code of Practice for Risk Management of Tunnel Works recommends this approach of continuity in risk management procedures, it is silent on the specifics of how this should be achieved. This paper will explore the perceived benefits and disbenefit of including the project Risk Register with bid documents; format and content that should be transferred and lessons learned using the case history of bidding and early construction phase of the Bi-County Water Tunnel in Montgomery County, MD

By R. J. Sweigard

Deep tillage is used widely as a Means of alleviating excessive soil compaction. There has been some concern that the voids created by deep tillage may collapse before a more natural soil structure develops, resulting in recompaction subsequent to deep tillage. A laboratory investigation was conducted to determine the feasibility of pneumatically injecting organic material into the voids during deep tillage to prevent any significant recompaction from occurring. Various amendments were injected into the soil in the laboratory using a small-scale ripping and injection system. Measurements were made of selected soil properties to evaluate the feasibility of this method.

Jan 1, 1993

By A. Tordoir, S. S. Kanchibotla, W. Rogers, E. Engmann, B. Bisiaux, S. Ako

Blast-induced rock mass displacement can have a significant impact on ore loss and dilution. The mischaracterization of the grade boundaries both prior to, as well as a result of, blasting can lead to significant financial losses due to ore loss and dilution. Ore dilution occurs when waste material is miscategorized as ore and sent for processing or stockpiling, diluting the run-of-mine head grade and recovery. Ore loss takes place when valuable mineral is miscategorized as waste and sent to the waste dumps, thus never being processed and recovered. Extensive research has been conducted at the University of Queensland over the last fifteen years to understand the impact of blast movement on ore loss and dilution. Recent outcomes of this research have led to the development of innovative tools and techniques to measure and model blast movement. These techniques have been implemented at the Ahafo gold mine in Ghana to understand blast movement dynamics and to implement solutions to reduce blast-induced ore loss and dilution. These solutions are validated through controlled trials and have been incorporated into site standard operating procedures.

Jan 1, 2012

By T. E. Wilson

An exploration bore core sample of coal ought to be reduced from its original cylindrical form to a particle size distribution and particle composition that reflects, insofar as possible, a process stream of? raw? coal it represents. Often, coal cores are reduced with a laboratory crushing machine, the product of which may not match the raw coal size distribution or size fraction composition. This study employs drop-shatter impact breakage followed by dry batch tumbling in a steel cylinder rotated about its transverse axis in order to characterize the core material in terms of first-order and zeroth-order breakage rate constants. These are indices of the propensity of the coal to degrade during excavation and handling. Initial drop-shatter and dry tumbling tests were done with synthetic cores, to reduce material variables and . conserve difficult-to-obtain coal cores.? Cores of three different coal beds --Illinois No.6, Upper Freeport, and Pocahontas No. 5 -were subjected to drop-shatter and dry batch tumbling tests to determine breakage response. Comparison of coal preparation plant feed with a crushed bore core and a bore core prepared by drop-shatter and tumbling (all from the same Illinois No.6 coal mining property) indicated that the size distribution and size fraction composition of the drop-shattered/tumbled core more closely resembled the plant feed than the crushed core.

Jan 1, 1998

By Paul E. Rosten

This paper describes some of the latest improvements that have been incorporated or planned by the Cleveland-Cliffs Iron Company to reduce operating costs and improve pellet quality. The Cleveland-Cliffs Iron Company operates and manages mining, beneficiation, and pelletizing operations in Michigan, Canada, and Western Australia. This paper deals with the grate-kiln pelletizing operations at Republic, Humboldt, Tilden, Empire, and Pioneer in Michigan, and the Adams and Sherman in Ontario, Canada. Table I characterizes .each operation in regard to location, ore type, pellet capacity and date that pellets were first produced. All of the operations with the exception of Pioneer and Tilden, utilize downdraft-two-pass grate cycles of drying followed by preheating. Pioneer utilizes an all-downdraft, three-pass grate cycle which consists of three drying zones followed by the preheat zone. The Pioneer and Tilden cycles have been described previously. (1) (2)(3) Tilden utilizes a three-pass grate cycle with a stage of updraft drying, followed by two downdraft drying stages. Recuperation systems which supply hot gases to a drying zone from second stage cooling were designed and furnished for Tilden I. Tilden II will be identical. Empire IV will also be furnished with a recuperation system. The Adams grate-kiln system was retrofitted with a recuperation system. This paper will summarize some of the efforts that are in effect or planned for grate-kiln pelletizing systems to (1) reduce operating and maintenance costs, (2) reduce energy requirements, (3) improve product quality, and (4) meet environmental standards.

Jan 1, 1977

By Andreas G. Mueller

Gold-silver and copper-gold deposits with high-temperature wallrock alteration of Ca-Mg-Fe-Al silicates occur in ca. 3.0 Ga old greenstone belts of the Yilgarn Block, Western Australia. The deposits are hosted by amphibolite-facies komatiites, basalts and BIF, controlled by ductile shear zones and located within the contact-metamorphic aureoles of composite granodiorite-granite batholiths. Disseminated sulfides and free gold form foliation-parallel ore zones in a gangue of anhydrous silicates (garnet, clinopyroxene, olivine), hydrous silicates (amphibole, biotite) and calcite. The deposits may be classified on the basis of their dominant economic metals as: 1(1) Gold skarns with substantial silver as by-product, represented by the Marvel Loch mine (production: 2,200,000 t at 3.5 g/t Au), and characterized by the mineral association pyrrhotite, loellingite, arsenopyrite, galena, gold and magnetite. (2) Gold skarns with low silver contents, represented by the Nevoria mine (production:1,850,000 t at 3.4 g/t Au), and characterized by the mineral association pyrrhotite, chalcopyrite, arsenopyrite, gold, Bi-tellurides and magnetite. (3) Copper-gold skarns, represented by the Elverdton mine (production: 850,000 t at .7 5 Cu, 0.81 g/t Au), and characterized by the mineral association magnetite, chalcopyrite, pyrrhotite, pyrite, gold and Ag-Bi tellurides.

Jan 1, 1990

"A commercially available Through-the-Earth (TTE) communications system was evaluated at an active underground longwall mine in West Virginia. This TTE system uses electric field (E-field) sensing to send text based communications using two separate antenna arrays connected in parallel. Each antenna array is composed of interconnected, grounded metallic rods or other such structures. Two-way communication between subsurface locations was investigated in this study using various antenna configurations. This field study was conducted as a part of a larger multi-site evaluation of available TTE systems in an effort to determine their operational sensitivity. INTRODUCTION Wireless, Through-the-Earth (TTE) communication technology is designed to achieve point to point communication through solid strata using very low frequency (VLF) and ultra-low frequency (ULF) electromagnetic waves. This ability allows TTE communication to function without the need for intermediary communications infrastructure, such as repeaters. As a result, such communication systems have the potential to provide reliable, robust communications between surface and underground personnel. Exploration into the use of TTE technology for this purpose dates back to the 1920s (Jakosky and Zellers 1924; Pittman, Church and McLendon 1985), but U.S. permissibility requirements slowed the development of TTE equipment for widespread implementation (Durkin 1980; Pittman, Church and McLendon 1985). One of the primary challenges in producing wireless TTE communications is the counteraction of signal attenuation when propagating through solid strata (Barkand, Damiano and Shumaker 2006; Wadley 1949). The long wavelengths of TTE transmissions make them well-suited for reducing the rate of attenuation. However, even when operating within the VLF to ULF range, the performance of TTE systems is still affected by geologic and anthropogenic factors (Geyer 1973; Geyer and Keller 1976; Geyer, Keller and Ohya 1974; Jakosky and Zellers 1924; Large, Ball and Farstad 1973). Although commercially developed TTE systems have demonstrated the ability to communicate through a variety of conditions, their range and performance have been highly varied (Barkand, Damiano and Shumaker 2006; Geyer and Keller 1976; Geyer, Keller and Ohya 1974; Ilsley, Freeman and Zellers 1928; Jakosky and Zellers 1924; Yenchek et al. 2012)."

Jan 1, 2016

By Micheal Mitariten

The recovery of natural gas (primarily methane) from coalbed deposits is an established and growing source for the U.S and accounts for over 7% of its total production. The gas from on-purpose degassing is often pipeline quality and requires only compression and dehydration before being admitted to the pipeline grid. However, the raw gas is sometimes contaminated with nitrogen (N2) and/or carbon dioxide (CO2) that can make the gas inadmissible to the transportation pipeline. In general, the N2 must be 4% or less and the CO2 should be 2% or less. In treating gas produced from virgin coal bed or from degassing operations where CO2 is present, amine systems are traditionally used for its removal. Engelhard’s Molecular Gate® adsorption system offers an attractive alternative due to its skid-mounted equipment, low pressure and unattended operation, cost and high on-stream reliability. Natural gas can also be sourced from the residual coal, after the coal has been mined. This source can be the GOB or gas remaining in abandoned coal mines. This source is almost universally contaminated, often with a combination of CO2 and N2. If the source is from air intrusion, the source can also be contaminated with O2. In treating CO2 / N2 contaminated feeds, the Molecular Gate adsorption system removes both of the impurities along with a level of O2 within a single processing step. To date, ten Molecular Gate units are underway with three systems having been installed for upgrading gas from abandoned coal mines. The technology consists of specialty adsorbents and advanced PSA processes that are jointly offered as fabricated packaged equipment by Engelhard Corporation and Guild Associates, Inc. Upgrading requirements, project challenges and project arrangements are discussed in this paper.

Jan 1, 2005

By Ralph W. Barbaro

This paper presents a cyclic queueing model which evaluates the productivity of a shovel-truck materials haulage system. For a cyclic queueing problem with exponentially distributed service times, a cyclic queueing model provides exact solutions in a fraction of the time that simulation takes to produce an approximate solution. The model is applied to an example problem, and the results are validated with simulation. Simulation is used to show that the assumptions of exponentially distributed service times and steady-state are not serious problems. A cyclic queueing model can be used to quickly obtain an accurate assessment of the productivity of a shovel-truck system.

Jan 1, 1986

By S.K. SHARMA, ANKUSH GALAV, G.S.P. SINGH

This paper proposes a hydromechanically coupled numerical modeling approach to quantify the influence of various parameters on the mechanical and hydraulic performance of protective water barrier pillars (PWBP). The results are validated for two case studies having pillar widths of 16 and 42 m at cover depths of 136 and 190 m and water heads of 25 and 141 m. The outcome can be significantly helpful in the rational design of these pillars in underground coal mines.

Mar 1, 2023

By Jens Classen, Thomas Kurth, Karl G. Holter

High performance sprayed concrete equipment installed on two 9.4 m diameter hard rock TBMs enabled a continuous sprayed concrete lining for the entire contour in both tunnels to be performed concurrently with the advancing TBMs. Innovative layout of the sprayed concrete arrangements comprised ring beam constructions each with two independent spraying robots. Each of the spraying robots were independently connected to sprayed concrete pumps, as well as a high capacity concrete logistics system on the backup. The mix designs focused on long open-time, excellent pumpability and tough requirements on strength development. The achieved output capacities of the sprayed concrete amounts to an average of 15 m3 per hour. Peak capacities of 24 m3 per hour have been realized.

Jan 1, 2003

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project was completed in 1998.

Jan 1, 1999

By Susanne Pignolet-Brandom

Flash smelting products of a copper sulfide concentrate collected at successive levels in an experimental reactor have been studied by reflected light microscopy, scanning electron microscope - energy dispersive analysis and electron nicroprobe analysis. Chalcopyrite, intermediate solid solution, bornite, chalcocite, metallic copper, magnetite, iron-copper spinel, pyrrhotite, hematite, delafossite and cuprite have been identified in the product samples. The detailed reflected light microscopy study of these phases and their abundance in the samples has resulted in the identification of the series of reactions during flash smelting.

Jan 1, 1985

By A. Cole, F. Porretta

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

Jan 1, 2002

By Kamran Esmaeili, MINGLIANG TANG

An understanding of the spatial and temporal variations of surface moisture content over a heap leach pad is essential for leaching production and to achieve a high ore recovery. The current leach-pad monitoring and data-collection practice remains highly labor intensive and exposes technical staff to cyanide solution, a hazardous material. To address these challenges, we propose using unmanned aerial vehicles (UAVs) equipped with thermal imaging sensors to remotely obtain image data with high temporal and spatial resolution for monitoring the surface moisture distribution over heap leach pads. A field study was conducted over a sprinkler-irrigated heap leach pad at El Gallo gold mine in Sinaloa, Mexico, and the acquired data were used to generate moisture distribution maps of the heap leach pad’s surface. The created moisture maps provide direct visualizations of surface moisture variation over the surveyed area. Such graphical results are effective tools for inspecting heap-leaching operations.

By Manuel R. Lastra

Critical to successful dump and heap leaching for gold, silver, copper and uranium are factors such as permeability, solution delivery to the ore, and solution recovery. This paper deals with possible techniques for successful accomplishment of these three factors. New developments as well as older techniques are discussed, together with rationale for use of some techniques in reference to others. The authors hope to present a checklist so that the ideal application to individual mine situations can be achieved. This involves a discussion of the merits of each different method and the situations for most logical application. It is hoped that such discussion will broaden the geographic areas where dump and heap leaching can be applied to include greater winter cold and tropical regions of large amounts of rainfall.

Jan 1, 1984

By Hans Ruge

The El Soldado copper mineralization occurs as relatively high-grade irregular ore bodies with assay contacts and with frequent inclusions of barren rock. The sampling method must be timely for production grade control purposes, as well as accurate and inexpensive. Sampling techniques evolved from sampling dump cars at the haulage level to sampling scooptrams at the loading pockets. These were abandoned in favor of sampling production blast holes. Several sampling alternatives are discussed. These involve the selection of optimum volumes and sampling frequencies while taking into consideration geological parameters and statistical analyses of sampling data.

Jan 1, 1984

By Felix Schmid

ABSTRACT Lateritic bauxite deposits of economic size and grade in Sierra Leone occur on granulites of the Kasila series. The high grade trihydrate ores of Mokanji are exploited by SIEROMCO since 1964. Remaining reserves are small (2 million tons) and operation moved over to the Gondama deposits of similar grade. Port Loko bauxite reserves are estimated at 100 million tons and are of relatively lower grade. It is planned to treat this ore locally into alumina. Guinea's bauxite reserves exceed those of any other nation. They occur as hard lateritic bauxite covers on plateaus of the Pre-Cambrian sedimentary formations and on doleritic intrusions. The genesis is still controversial. The Sangaredi mine has produced high grade ore for the last 10 years. Friguia exploits a relatively lower grade ore at a rate of about 2 million tpy to be treated in their local alumina plant. Kindia ore is mined at a yearly rate of 2,5 million tons since 1974. Untouched reserves at Ayékoyé and Tougué/Dabola are estimated at 6,000 million tons.

Jan 1, 1984