Search Documents

By Roberto J. Guardia, Ted Lewtas, Peter Rasmussen, Klaus Winkler

As part of the Lake Fort Smith Water Supply Dam Enlargement project, located in northwest Arkansas, microtunneling methods were used to install two side-by-side,1.53m (60-in) inside-diameter steel pipes between the intake structure shaft and the lake. The 46.6 m- (153 ft-) and 41.7 m- (137 ft-) long tunnels were excavated in Pennsylvanian sedimentary bedrock ranging from coarse sandstone to siltstone and shale-like claystone. The intake tunnels were constructed 18.3 m (60 ft) below lake level from the dry shaft. Special installation methods and procedures described herein were used to complete the lake taps. Installation difficulties that caused minor delays are also reviewed. After the excavation of the Intake shaft was completed, the two lake taps were installed in approximately ten weeks with the same microtunneling machine.

Jan 1, 2005

By Ihsan Berk Tulu, Haochen Zhao, Deniz Tuncay

The process of designing pillars and selecting support measures in underground coal mines relies highly on the accurate assessment of mining-induced loads and the load-bearing capacities of the supports. This study proposes a new method to estimate the percentage of load carried by the gob in underground coal mines using a new parameter that introduces the site-specific overburden geology.

Jun 1, 2023

By George A. Komadina

The Pima Mining Company lies 20 miles southwest of Tucson, Arizona, and some 45 miles north of the Mexican border. The mill is situated on a hillside overlooking Tucson and the Santa Cruz Valley, the ground generally sloping northeast at a 2.5 percent grade. The hillside location allows for gravity flow generally through the plant as well as for: tailing disposal.

Jan 1, 1965

By Deepak Malhotra, Linda Battich

INTRODUCTION Mineral processing plants generally operate efficiently within the technical, economic and management constraints applied to them. They have no choice, because the dynamic and competitive nature of the mineral business dictates that survival and/or prosperity of the company depends on being a low cost producer. Progressive mineral companies realize that market downturns will occur, and they must continuously strive for lower unit production costs rather than be satisfied with the status quo. Mineral companies generally tend to reduce costs during market downturns. This short-term solution is achieved by high grading of ores, and cut-backs In waste stripping, exploration, and capital expenditures.(1) However, to remain a low-cost producer in the long term, companies must enhance revenue and reduce cost simultaneously. This Involves continuous evaluation of technologies and reagents, periodic audits to locate revenue losses; and gathering and analyzing statistical plant data to clearly understand the Impact of process variables on efficiency. Mineral companies are caught in a Catch-22. They need resources to accomplish the objectives outlined above. Most mill stuffs have been cut to the minimum level necessary to maintain production. Resources such as time, manpower and money are scarce, and mill metallurglsts struggle to use these resources productively. Is your flotation plant optimized? History Indicates that successful operations constantly tune the flotation circuits to Improve metallurgy or reduce cost. This Is the essence of evolutionary change In mineral processing operations. A plant auditing approach can play a key role in assisting the process engineers to achieve the overall objective of enhancing metallurgy and reducing cost with limited resources through evolutionary improvements. FLOTATION SYSTEM The flotation process is the most widely wed concentration process In the world today. The number of variables that can affect the flotation results Is very large, maybe over 100. These variables can be divided Into three main groups: (2) (1) ore and mineral properties; (2) reagent treatment; and (3) flotation machine characteristics. Some of these variables can be controlled while others have to be accepted. Recently, Investigators (3,4) have attempted to describe the flotation process as an engineering system which includes chemistry, equipment and operating variables. Though some of the variables are Independent, most are co-dependent. thus making it difficult to develop simple cause and effect relationships. For example, it is easy to understand the effect of reagent change on recovery and grade In the rougher circuit, but very difficult to quantify Its impact on filtration downstream. Plant audits on a periodic basis are necessary to develop an understanding of the Interactive nature of the system. Auditing provides comparisons of plant operating performance before and after variable changes. OVERVIEW OF PLANT AUDITING An audit Is a formal, thorough and periodic examination of a system. There are various types of audits (i.e., geological, environmental, metallurgical. economic, etc.), and each serves a different purpose. (5) The discussion here is related to plant and/or metallurgical audits. Neale and Flintoff note that two key factors governing changes In an operation are: (1) the opportunity must be recognized; and (2) the justification for change must exist. (6) Both factors emphasize the critical role of successful plant auditing. Without plant audits. many opportunities for improvement must go unrecognized. On the other hand, when a situation ripe for improvement Is recognized. the hard data from a plant audit can reveal the expected impact of an operating change.

Jan 1, 1993

By Nicholas S. Lynn

Introduction Borne out of the need for reductions in capital expenditure and increased production, several new and innovative carbon systems have been developed for small precious metal heap leach operations throughout the United States. Perhaps the most important aspect of these systems is the carbon column. Though diverse in design, these columns can be categorized into three basic types. The first is known as the gravity flow type or Cortez type. As the name indicates, solution flows via gravity, throughout 4 to 6 columns which are arranged in a normally stepped con- figuration which is conventionally upflow in design. The second type, known as the vertical column, is an arrangement whereby flow is established through pressurization in an upward manner, throughout 4 to 6 columns in a vertically stacked configuration. This arrangement is typically intended for use with small portable heap leach operations and employs a semi-continuous mode thus preventing gravity from occurring. The third type and newest development in carbon columns is an arrangement whereby the solution flows throughout 4 to 6 columns placed in a side by side configuration and pressurized by a single feed pump (Figure 1). A unique aspect to the third type, is that the adsorb and desorb cycles are accomplished in the same column, due to a fixed carbon charge. An in-depth analysis is warranted due to numerous advantages of this arrangement, and is therefore the subject of this paper. Advantages and Variations One advantage to the third type of carbon column is the fact that initial capital expenditures and operating man- power requirements are reduced. Another advantage is that the system can be made fully portable up to a 0.0315 m3/s (500 gpm) capacity. Systems of this nature are operational at several sites. Above this flow rate, the system's portability is one which can be maintained, but disadvantages (i.e. larger diameter carbon column and greater weights) far outweigh the advantages. There are several variations in each of these systems which allow for unique operation. For example, carbon columns made highly portable, can be moved from unitized heap leach operations to central stripping facilities. Although this method has been used in Colorado, transportation of these units has been known to be quite cumbersome. If distances exceed 5 km (3.2 miles) then special front-end loaders are required. This limits heap locations to within 5 km (3.2 miles) of the central processing facility. Another example transports the carbon charge from the heap leach locations to a centralized processing facility; this method is quite effective. For the past 5 years one mine has employed this technique of transporting carbon in 907 kg (1 ton lots), in DOT containers, towed by company pick-ups. This operation uses a vertical column with a 907 kg (1 ton) carbon charge. A third example uses static carbon columns with fixed carbon charges. Carbon Adsorption System The carbon adsorption system (Figure 1) is fed by a single preg solution feed pump. This feed pump pushes the preg solution through all four to six fixed charged carbon columns, which are on line. The sequencing of the carbon columns is achieved using valves. Expansion of the carbon charge is dependent upon the carbon selected. The carbon typically used is a 6 x 12 mesh size, with a nominal flow rate of 0.00135 - 0.00138 m 3/s (22-25 gpm) per square foot of carbon, based on a 40% bed expansion. With 8 x 16 mesh size,

Jan 1, 1987

By W. Todd

The Robbins Company has developed a boring machine, with a rubber packer serving as the gripper system, for blind boring of raises without using drill pipe. This machine is the BorPak and has many applications for use in the mining industry which will improve productivity. In addition to the cost savings, the boring method will lead to increased safety in constructing blind raises. The advantages of using the BorPak in a mining environment will be discussed together with possible applications.

Jan 1, 1994

By Robert M. Jimeson

The competitive market potential for solvent refined coal is estimated. Market advantages of solvent refined coal are enumerated. Markets are possible in combustion, railroad locomotion, and carbon electrodes. The combustion characteristics are consistent with expected air pollution restrictions on the emission of sulfur and particulate matter. A market potential of sufficient size exists to support the initiation of solvent refining in the United States. The market analysis should help fuel producers determine the advisability of their undertaking the solvent refining of coal.

Jan 1, 1969

By Robert W. Carn

This paper presents the concepts which are presently being utilized in the design of coal export terminals. Criteria for selecting a viable site and establishing the terminal plan are presented. Factors affecting the design of the terminal as well as the present techniques and procedures in use today to determine the optimum use of equipment will be discussed along with the current trends in export terminal control systems. Finally capital and operating costs for a typical export terminal are reviewed.

Jan 1, 1982

By Pratt Rogers, Aaron Young

This paper considers the mining industry’s need for digital transformation (DT) and presents a three-part review of the foundational components of the DT process: ubiquitous data, connectivity and decision-making. It also provides a discussion on the future of DT in mining as well as a research direction, which identifies the need of academia to provide support for mining companies in the form of both research and the education of digitally literate, dynamically capable mining engineers into the coming decades.

By K. V. Raj, C. A. Berry, A. T. Weakley, A. L. Miller, P. R. Griffiths, D. A. Parks

Diesel particulate matter (DPM) has been classified as a carcinogen to humans by the International Agency for Research on Cancer. As a result of its potential carcinogenic nature, DPM exposure is regulated by the Mine Safety and Health Administration. Currently, diesel emissions in the workplace are monitored by collecting the aerosol onto filters, which are then sent to a laboratory for thermal-optical analysis using the NIOSH method 5040. This process can take days or even weeks, and workers can potentially be exposed to excessive levels of DPM before the problem is identified. Moreover, the delay involved in getting the loaded filter to the lab inevitably means the loss of some of the more volatile organic carbon. To remedy this delay, researchers from the National Institute for Occupational Safety and Health are seeking to develop a field-portable, real-time method for measuring elemental and organic carbons in DPM aerosols. In the current study, the use of mid-infrared spectrometry was investigated. It is believed that mid-infrared spectroscopy is more suitable for use in a real-time field-portable device than thermo-optical analysis methods. This article presents a method for measuring organic carbon (OC) and elemental carbon (EC) in DPM for a broad range of OC/EC ratios. The method has been successfully applied to laboratory-generated and mine samples.

By M. M. Hajdasinki

A project's rates of return (RORs)1, be it the internal rates return (IRRs) or one of the many IRR surrogates, frequently needs to be approximated. The success and efficiency an ROR- approximation procedure depend on the quality the approximation-initiating parameters, such as bounds or seed values (guesses). The existing approximation procedures commonly use bounds and guesses suggested by intuition rather than supported by mathematical considerations. This paper presents three mathematically founded ROR-bounding and eleven ROR-guessing approaches and examines their suitability by using examples of typical project cash-flowpatterns (CFPs). The calculated bounds and guesses not only improve the approximation efficiency, but also allow the process of the ROR discovery to be automated, thereby making it more convenient and reliable.

Jan 1, 1999

Direct force measurements were conducted using an atomic force microscope (AFM) to study the mechanism of copper-activation of sphalerite. The force measurements were conducted between a sphalerite plate and a hydrophobic glass sphere in xanthate solutions of various pHs. The glass sphere may represent the hydrophobic air bubbles interacting with minerals during flotation. The force measurements conducted with unactivated sphalerite in 10') M KEX solutions did not show the presence of hydrophobic force. On the other hand, the results obtained with copper-activated sphalerite at pH 9.2 and 4.6 showed strong hydrophobic forces. However, the results obtained at pH 6.8 showed no evidence of hydrophobic force, which provides an explanation for the difficulty in floating sphalerite at neutral pH.

Jan 1, 1998

By Sergio Estebanez, Martha Gross, Ruben Rubal, Yvonnick Rescamps, Alexandre Cochennec

The Hampton Roads Bridge-Tunnel (HRBT) Expansion project in coastal Virginia, USA will add two 1.5-mile (2.4 km) TBM bored tunnels alongside two existing immersed-tube tunnels between artificial islands. The site’s unusual constraints and the requirements of a large-diameter variable-density TBM shaped the design-builder’s decisions for handling TBM inputs and outputs, siting the TBM plant and supporting equipment, and sequencing tunnel-construction operations. This paper addresses the logistics necessary to enable key functions of the 46-ft (14-m) TBM and its ancillary equipment, including transport of most materials by barge, U-turn of the TBM on an artificial island, and delivery of materials for the second tunnel through the first one while interior structures are under construction.

Jun 13, 2021

By G. Bonifazi

In the present work the possibility to utilize the morphometrical and morphological characteristics of an articulate solids system in a slurry flow to monitorate and to control a continuous process is considered. This goal has been reached by mean of an optical system able to acquire, to handle and to process the pictorial information derived by a suitable hardware architecture designed to realize the best lighting, focusing and sampling conditions for the examined flow stream domain. The procedure has been tested using different flow stream slurries coming from different sections of a beneficiation plant. A suitable strategy and a consequent software architecture has been set up in order to assure to the system the necessary speed and the stability to achieve correct on-line measurements and control.

Jan 1, 1994

By I. Raposo, I. Moreno-Ventas, A. Palma, M. J. Díaz, M. Vázquez

The oxidative degradation kinetics of chalcopyrite have been studied by thermogravimetric analysis (TGA). The obtained data are necessary for the kinetic description of the flash fusion process, which can contribute to the optimization of the smelting process in copper extractive metallurgy. Activation energy (Ea) evolutions of the involved processes have been determined by several isoconversional methods; in this sense, the chalcopyrite oxidation processes could be adequately described, among studied models (E1641–16, Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose and Friedman), by the Kissinger–Akahira– Sunose kinetic model. Using this method, Ea and A values are found to be very dependent on the conversion. Under lower conversion levels, higher Ea and A values have been calculated with respect to that found for medium and higher conversion levels.

By Francesco Chiappalone, Franco Gasperin, Fabrizio Fara

This document describes the challenging task of mining through tiebacks using a 21'-8" diameter Tunnel Boring Machine (TBM) as part of the Ship Canal Water Quality Project. The mining operation involves navigating through 17 tie-backs that are evenly spaced at 8-foot intervals, with many intersecting the full face of the cutterhead. Detailed analysis and review of TBM parameters specific to this area have been conducted to ensure operational efficiency and safety. Hyperbaric interventions have been planned and coordinated, encompassing pre-mining preparations, continuous monitoring and adjustments during the mining process, as well as post-mining measures. The document highlights the complexity and importance of strategic planning and execution to successfully overcome the tie-back intersections during the mining operation.

Jun 23, 2024

By Shawn McWilliams, Aini Sun, Mike Lichte, Greg Colzani

The Allegheny County Sanitary Authority (ALCOSAN) adopted its Clean Water Plan (CWP) in May 2020, as part of a federal consent decree to comply with the USEPA’s Combined Sewer Overflow (CSO) Control Policy. Planned improvements include constructing a new regional storage/conveyance tunnel system, promoting green infrastructure/ source control, and expanding the treatment plant. Preliminary planning for the tunnel system was completed in October 2020. The Ohio River Tunnel (ORT) project is the first of three tunnel projects that make up the regional tunnel system. The ORT project began final design in 2021. This paper discusses the advancements made to the ORT preliminary planning concepts considering property availability, alignment optimization, tunnel boring machine evaluation, contract packaging and delivery schedules.

Jun 13, 2023

By R. Benito

The publication of the Lerchs Grossmann paper in 1965 outlining a threedimensional graph algorithm for ultimate pit definition set the standard for the mining industry regarding pit optimization. Although the algorithm provides a solution from a static standpoint (i.e., assumes instantaneous mining), it is widely used for commercial packages to generate ultimate pit limits and intermediate phases. However, the solutions delivered are presented in canned reports lacking connection to the original data, which prevents further data analysis and extended reporting. The approach presented in this paper attempts to overcome such barriers by performing openpit optimization through databases. An adaptation of the Lerchs Grossmann graph algorithm is used to generate nodes, arcs and tree structures in customized tables to determine the maximum closure of a graph.

Nov 1, 2013

By H. Colijn

Belt conveyors have proven themselves for many years as a dependable and low cost method of handling bulk materials at high flow rates. The success of a belt conveyor system greatly depends on the initial loading of the material on the belt. If the material is loaded on the belt at the center, at approximately the same speed and with minimum impact, then most of all belt conveyor problems disappear. Proper belt loading is primarily determined by the engineering and design of the conveyor transfer point. This paper will establish and discuss some general design criteria required for proper loading and transfer of materials from one conveyor to another. Specific attention is given to loading points, chutes, skirt board length and general design of transfer structures.

Jan 1, 1971

By Paul D. Bybee

The Freeport Sulphur Company operates four sulphur mines in the coastal marsh area-03 South Louisiana. Employing the Frasch process of mining, approximately 13-million gallons of water per day is heated to a mining temperature of 325°F and is injected into the sulphur bearing formations of the four mines. A volume of cold waste water, roughly equal to the Input, is removed from the formations and presents a disposal problem. Two additional mines are currently being developed and will increase the disposal volume by an additional 5-million gallons per day. Although these properties are in a relatively small area, geographically speaking, as shown in Figure 1, they each represent a separate disposal problem with the treatment methods designed for the individual mine.

Jan 1, 1959