Search Documents

By Robin J. Hickson

El Abra has mining concessions granting the right to exploit minerals in more than 130 km2 (32,122 acres). SCM El Abra owns “rights to occupy” the surface of these claims. The company also owns the surface rights over the process plant area and over land conveyor route. The project has procured all material easements relating to the mine area, processing facilities and access rights of way. Engineering, procurement and construction Figure 1 sets out the development and construction schedule for the project. Development is already well under way. As of early January 1996, about 70% of the project was complete and more than 80% of the capital expenditures were committed.

Jan 1, 1996

By S. A. Shoop, J. J. K. Daemen

Site-specific blast vibration prediction can be more accurate than using a universal prediction equation. Vibrations from 37 blasts were monitored using three seismographs. Data analysis showed that square root, cube root, and site-specific scaling predicted ground motion with equal reliability. Imprecise prediction is caused by geologic and blast variability, particularly, inaccurate delay times. Vibrations at some mines were consistently lower or higher than vibrations predicted from US Bureau of Mines (USBM) equations. Vibration restrictions based on USBM studies could then be too conservative or too lenient. Predominant vibration frequencies were generally less than 50 Hz, but several blasts had significant energy up to 125 Hz. In some cases, energy was concentrated at frequencies corresponding to delay intervals.

Jan 3, 1985

By S. D. Thompson

Several discrete-event simulation models have been developed for designing the conveying system capacities of underground coal mines. Most of these models require the use of a step function approach to mimic the loading process at each conveyor loading point. Over the years, practitioners have generally employed one of three versions of the step function approach. An important issue is how these three versions compare to each other in terms of simulated capacity requirements for belt conveyors. Another issue is how they compare to the peak capacity design. This paper addresses these issues by statistically and quantitatively comparing their simulation results. The consequences and problems associated with using each version are also discussed and summarized.

Jan 1, 1998

By John Waggoner, Steve Klein, John Townsend, Jay Arabshahi

The Riverside Badlands Tunnel is a 13 km (8 mile) long segment of the Inland Feeder Project. This 3.65 m (12 ft) finished diameter water tunnel presented many challenges that had to be overcome to take the project from concept to reality, not the least of which were the diverse ground conditions. Construction of the tunnel was carried out by a single tunnel boring machine (TBM) in one tunnel drive. The project is considered a success due to the accurate baseline established for the ground conditions; the approaches used to mitigate adverse conditions; and the appropriate use of TBM excavation methods, which achieved rapid advance rates despite the challenging ground conditions.

Jan 1, 2003

By L. B. Kirk, A. R. Kirk

At New World, Au-Cu-Ag mineralization occurs in stratiform car-bonate-hosted, massive sulfide-iron oxide, and skarn-replacement deposits. Regional pyritic-alteration, local massive sulfide mineralization and mine wastes generate acid drainage within the district. Water quality improves down gradient through dilution and mixing of acid and metal-rich mine water with bicarbonate-rich, low-metal surface and groundwater, and precipitation of metal-rich ferrihydroxide phases. Natural deposits of ferricrete indicate that pre-mining ARD has occurred, providing important clues to pre-mining water quality. The geoenvironmental model identifies the Cu-skarn mineralization as the primary target for ARD management. Closure success will be limited by the geoenvironmental nature of the natural mineralization.

Jan 1, 2004

By J. Jeremy Burden, Bruce S. Brown

A major question in the design and permitting of a tailings storage facility is the quality and quantity of seepage which will occur from the base of the tailings facility into the underlying foundation and groundwater regime. A corollary to this is what liner system, if any, is necessary to protect the groundwater regime from unacceptable contamination. Modern tailings storage facilities are generally designed as drained tailings deposits whereby all free water is removed from the facility by decant, drainage and evaporation. This removes the source of on­going seepage and allows for efficient and timely reclamation of the facilities. Quantifying the residual seepage from the base of the tailings deposit is complicated due to the following factors:

Jan 1, 1992

By Richard J. Frechette

Very few facilities containing hydraulically deposited tailings have been completely reclaimed and capped at this time. Design of a closure cap for a tailings impoundment has relied heavily on consolidation theory in order to achieve a cap that maintains sur­face drainage. Obtaining data for the consolidation evaluation can be difficult and costly. The author reviews the performance of two tailings impoundment closure caps that have been suc­cessfully installed and presents the experience gained from these projects with an emphasis on the ability to optimize cap design through post-operational monitoring prior to initiating cap con­struction. Using the optimization approach, a significant earth­work quantities reduction may be realized for the ultimate cap.

Jan 1, 1998

By A. N. Islam, C. Simons, M. N. Hughes, J. Barrett

The effluent from the bio-oxidation of arsenopyrite contains high concentrations of iron(III) and arsenic(V), the pH being in the range 1.0-1.3. The use of lime to increase the pH causes the precipitation of calcium sulfate, calcium arsenate and a mixture of solids containing calcium, iron and arsenic. The presence of calcium is due to slaked lime encapsulated by the iron arsenate precipitates. These iron arsenate solids are related to known minerals. The use of sodium hydroxide to effect the precipitation of iron and arsenic produces solids which are more stable than those produce by using slaked lime. The use of limewater produces an initial precipitate of calcium arsenate.

Jan 1, 1991

By Dewey W. Marino

Conventional remote sensing applications for the exploration of natural resources has largely been the domain of low resolu­tion Earth orbiting systems such as Landsat™ which can sample a broad range of the spectrum. As the classic application of remote sensing, it has proven its worth through the discovery of numerous mineral deposits worldwide. Often this technique relies more on the spectral content of the imagery for narrowing potential sites on the ground, but often cannot reveal the detailed context of the observed response. As the dawn of the new era in remote sensing grows closer, high-resolution imagery is proving its worth for the definition of mineral potential and its cost sav­ing advantages for mine management.

Jan 1, 1998

By Dale J. Sadowski, Richard J. Switalski, Kyle R. Ott

This paper discusses design and construction aspects of shaft construction through rock saturated with petroleum hydrocarbons (crude oil). During the subsurface exploration phase for design of the Hilltop Interceptor project in Cleveland, Ohio natural crude oil was encountered at depths between 6.1 and 61 m below ground surface. The oil-saturated Euclid sandstone contained up to 12,000 mg/kg total petroleum hydrocarbons (TPH), various volatile organics, and had flash points as low as 18.9°C. Interceptor hydraulic design required that construction of access and/or drop shafts penetrate the layer of petroleum hydrocarbon saturated rock. This led to the design of a special lining and some special handling procedures for the excavated material.

Jan 1, 1995

By Li Honggui, Liu Maosheng, Zhao Zhongwei, Sun Peimci, Li Yunjiao

Leaching of Shizhuyuan low-grade refractory tungsten ore was carried out in a mechanically activating reactor. The effect of experimental parameters-temperature, amount of Na2C03, addition of NaOH, ratio of liquid to solid and leaching time - on the recovery of WO3 was studied. The WO3 recovery up to 96.99% have been achieved when the tungsten ore was digested by soda not more than three times the stoichiometric amount at 185-195°C for 1 .O-2.0 hours. Iso-extraction countour diagrams were drawn to illustrate the effect of various parameters on leaching. The WO3 recovery could be expected to increase 10-15% compared to that of conventional soda autoclave process.

Jan 1, 1995

By William E. Little, William R. Sharp, Edward R. Kennedy

Cost o f mechanical tunneling requires the knowledge of many machine/rock parameters such as rock types, machine power, penetration rate, cutter life, maintenance schedule, etc. Capital investment, labor requirements, and project scheduling will all play an important role in defining the economics of the overall project. Knowledge of the cost sensitivity of different project parameters will improve the overall success of any particular tunneling project if this information is incorporated into an effective management plan. Through the use of an interactive graphic computer program written for a microcomputer, one has the ability to quickly evaluate relative costs for a variety of parameters for either an existing project or for a proposed site.

Jan 1, 1983

By A. Iordanidis

Fly ash samples were collected from two large lignite-fired power plants of Ptolemais region, northern Greece. Environmental Scanning Electron Microscopy (ESEM) was applied for the characterisation of the samples. ESEM coupled with Energy Dispersive System (EDS) provided fast and accurate results on the morphology, mineralogy and chemical composition of the fly ash particles. Fly ash consists mainly of aluminosilicate glass, silicates, oxides-hydroxides, sulphates, carbonates and char. Various types of chars, spheres (e.g. ferrospheres, cenosphers, plerospheres etc.), spheroids, agglomerates and mineral crystalls were observed. The size distribution of the fly ash particles was correlated with their mineralogical and chemical composition. Possible environmental impacts and potential utilization is also discussed in this study.

Jan 1, 2005

By P. M. Lin, P. Tsang, S. S. Peng

This paper presents an overall stabilization method to eliminate the potential of reoccurrence of subsidence over abandoned mine lands (AML). The method considers column grouting at specific locations, including the destressed and stress concentration zones, instead of grouting around and beneath damaged structures. The latter method is currently commonly used for AML subsidence abatement. The finite element method (FEM) can be used to calculate stress distribution in the strata before and after grouting. A grouting pattern is generated that includes the location and number of grouting holes. Stress concentration can be reduced or eliminated. A comparative analysis, including the number of grouting holes, area of grouting influence, stress level and potential of subsidence reoccurrence, is also presented.

Jan 1, 1993

By S. P. Liebenberg

During the past fifteen years significant progress has been made on carbon-in-pulp (CIP) technology for the extraction of gold. While most research on the mechanisms and kinetics of CIP sub-processes has focused on the adsorption step only, auxiliary unit operations such as elution have received less attention. The mathematical models which have been developed for elution at the University of Stellenbosch can be used for design as well as process optimisation by incorporation into an overall CIP simulation program. Except for these models, no other comprehensive models for the complex elution process are available. It is the aim of this paper to review recent modelling work on competitive elution from activated carbon.

Jan 1, 1995

By Peter T. Luckie

Coal represents 80% of the fuel reserves of this country, yet only 20% of the fuel consumption. In order to change this ridiculous situation, a realistic coal utilization roadmap needs to be drawn to show how we go from where we are to where we want to be. The completion of the roadways will require the building of research bridges. The research bridges on the coal processing section of the superhighway should be built to process 500pm by 100pm rather than 25pm by 0 raw coal . Particular emphasis should be on middlings processing and total plant performance. The superhighway should be layed out by a team of fuel, coal preparation and mining engineers.

Jan 1, 1988

By Lawrence M. Lenahan

Cleveland's Southwest Interceptor Contracts No. 3 and No. 4 are continuations of Contract No. 1 addressed at the 1987 RETC with geology, equipment, and methods that differ greatly. The two contracts consist of 791 m (4.22 miles) of 3.5 m (11.5 ft) tunnel lined to 2.9 m (9.5 ft), nine access shafts, six drop shafts, and six collection structures. The excavation drive was completed by the use of a 1970 vintage Robbins TBM hybrid for this particular job through the use of both new and old technology. All other excavations were successfully accomplished through drill and blast method in tight residential areas. Concrete lining and connections were completed nine months after holing through.

Jan 1, 1989

By Deepak Malhotra, Robert Dorfler

Modern engineering mill design has been refined over the years to the point where detailed ore and process specification criteria can be developed In the engineering design phase of the project. The plant Is then built to the detailed criteria and performance acceptance tested by the owner to see if the as-built mill meets the criteria, This performance testing is critical to the owner; the test must be systematic with sample collection coordinated throughout the plant. Despite the availability of systematic approaches to plant development, the new plants often fall short of design criteria. This paper discusses the key Issues a Project Manager/Process Engineer should Implement to ensure that plants meet design criteria.

Jan 1, 1991

By Konstantinos Theodoridis, Michael Galetakis, Olga Kouridou

Recent advances in Artificial Neural Networks (ANN) and Adaptive Neuro-Fuzzy Inference Systems (ANFIS) have provided a new approach to the estimation of related quality characteristics, such as heating value, ash content and moisture of coals used for power generation. The basic strategy for developing ANN and ANFIS models for the prediction of missing quality values, is to train the models using an existing quality data set and an appropriate learning method. Statistical analysis results of the estimated values, showed that ANN and ANFIS are not only more accurate than the widely used regression models, but also tends to reproduce the variability of the initial data, while regression models generate a smooth representation of reality.

Jan 1, 2002

By William R. Sharp

This paper describes a graphics station and graphics software designed specifically for use within the minerals industry. Through the graphics station, a user is able to recall maps for modification, display them on a color CRT, send the work to a plotter, and restore the work when finished. The engineer may use the system for the storing of data, per- forming engineering calculations, doing word processing, and performing general file maintenance. In addition, the system may be used to communicate with a mainframe computer for such purposes as: transmission of large data files, graphic 3-dimensional rotation of a mineral deposit or mine design, contouring of spacial data, and other data processing work.

Jan 1, 1982