Search Documents

By Daniel W. H. Su

Thick, massive sandstone present in close proximity of the mining horizon can create difficult longwall caving issues, which may lead to severe face loading and subsequent face roof control problems. Under deep cover, such delayed caving and overhang not only impose additional loading on the gate road pillar system, but they also increase the potential for large seismic events. Such a combination of thick, massive sandstone geology and deep cover was present over a portion of a southwestern Virginia coal mine, which was confirmed via detailed in-mine roof scoping and mapping. Large seismic events were recorded over a district of 1,000-foot-wide longwall panels. This paper presents the ground control design changes implemented to reduce longwall-induced stresses in the sandstone, to reduce longwall abutment pressures in the gate road pillars, and to reduce the magnitude of mining-induced seismic events. A series of two-dimensional finite element models were constructed and analyzed to evaluate the longwall-induced stresses in the sandstone above the gate road pillars and the abutment pressures within the gate road pillars. Results from the analyses indicated that reducing the panel width from 1,000 to 700 feet reduced the longwall-induced stresses in the sandstone by a factor of 2.0. Specifically the probability of sandstone stability improved from 29% for the 1,000-foot-wide panel district to over 95% for the 700-foot-wide panel districts. Also, the subcritical 700-foot-wide panel, coupled with a change in pillar design, considerably reduced the longwall-induced abutment pressures in the gate road pillars, which significantly increased the gate road pillar stability factor. Surface subsidence measurements conducted over the 1,000-foot-wide panel district and two new 700-foot-wide panel districts were in very good agreement with those predicted by the finite element models. In addition, results from the models indicated that wider panels with a smaller district may produce the same probability of sandstone stability. One four-panel district and one five-panel district with the new ground control design changes have been mined successfully. The panel width was found to be the most influential factor in determining the longwall-induced stresses in the sandstone and in the gate road pillars. The thickness and massive nature of the sandstone, the proximity of the sandstone, and the strength of the sandstone were also found to be important factors. Seismic monitoring over the two mining districts that employed 700-foot-wide panels confirmed the reduction of one order of seismic magnitude when compared with those measured over the 1,000-foot-wide panel district.

Jan 1, 2014

By Karsten Zimmermann, Peter Cain

"To receive regulatory approval for a new coal mining operation in North America, extensive investigations of feasibility and potential environmental impacts, including ground deformations, are required. Figure 1 shows pictures from mine sites and an example mine map with the planned panel layout for one seam of the multi-seam longwall operation considered.The cumulative mined coal thickness of 22 meters in some areas of the operation requires a comprehensive forecast of expected ground movements and subsidence impacts (e.g., subsidence, slope, displacement, curvature and strain). In the frame of the impact study, the prediction of these impact factors was conducted by DMT using the computer program SPS 4D, based on the Ruhrkohle modeling method by Ehrhardt and Sauer (1961).This paper briefly presents the modeling method and explains the benefits and possibilities for its international application. Information gathered from literature studies on subsidence in North America were incorporated into the initial model parameterization. The article shows the ways in which the observed influences of mountainous topography on surface displacements and deformations can be considered by an extension of the subsidence prediction model and integration of DEM information.SUBSIDENCE MODELFor the calculation of mining-induced subsidence and deformation, DMT has developed subsidence prediction software SPS 4D, which is built according to the stochastic prediction model by (Ehrhardt and Sauer, 1961). The model is based on the subsidence theory by (Knothe, 1953) with a specific parametrization of the stochastic influence function and includes enhancements for dynamic subsidence calculations after (Sroka, 1978). In Europe, mainly in Germany and Poland, the model is approved by the authorities as a standard model for subsidence prediction in mining areas. However, extensive research within R&D activities has shown the possibility to predict mining-induced subsidence considering the specific mining conditions in North America (Zimmermann and Fritschen, 2007)."

Jan 1, 2016

By Dongsheng Zhang, Xufeng Wang, Wei Zhang, Gangwei Fan

"Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately in Northwest China, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mining-induced fractures in overlying strata and its relationship to upper aquifers is critical. In this paper, the application of the geophysical-chemical properties of radon in mining engineering is explored as a potential solution to the shortcomings of existing surveying methods. A radioactive measurement method is proposed for the detection of the development of mining-induced fractures in overlying strata in the Baoshan Coal Mine (BCM). The on-site trial indicated that the first weighting step is approximately 60 m, the average periodic weighting step is approximately 20 m, and the influence coverage of the advanced abutment pressure is approximately 30 m. The presented method could be used as an indirect technical support to increase the safety of coal mining by acting as a simple, fast, and reliable method of detecting mining-induced fractures in overlying strata.INTRODUCTIONAccording to the latest coalfield prediction results provided by China’s National Administration of Coal Geology (CNACG) (Zhou et al., 2013), China’s coal resources are mainly distributed throughout the West, e.g., Inner Mongolia, Xinjiang, Shaanxi, Shanxi, Ningxia, and Guizhou. Two major coal mining areas have been established in the Northwest and the Southwest, and are typically represented by Inner Mongolia and Guizhou (Zhang et al., 2010). Northwest China is an arid to semi-arid area, where the coal seams are typically shallow and covered by a thin layer of bedrock. In its natural state, the surface’s ecological environment is fragile. Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. This can propel any potential ecological fragility into a state of actual destruction (Zhang et al., 2011). Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mininginduced fractures in overlying strata has become the theoretical basis of solving the above issues."

Jan 1, 2015

By Rob G. Jeffrey, Ken W. Mills, Jesse W. Puller

"A coal mine in New South Wales is longwall mining 300m wide panels at a depth of 160-180m directly below a 16-20 m thick conglomerate strata. As part of a strategy to use hydraulic fracturing to manage potential windblast and periodic caving hazards associated with this conglomerate strata, the in situ stresses in the conglomerate were measured using ANZI strain cells and the overcoring method of stress relief. Changes in stress associated with abutment loading and placement of hydraulic fractures were also measured using ANZI strain cells installed from the surface and from underground. This paper presents the results of in situ stress measurements and stress change monitoring undertaken as part of the hydraulic fracturing program.Overcore stress measurements have indicated the vertical stress is the lowest principal stress so that hydraulic fractures placed ahead of mining form horizontally and so provide effective pre-conditioning to promote caving of the conglomerate strata. Monitoring of the full-scale hydraulic fractures has confirmed the hydraulic fractures grow horizontally.Stress changes monitored during hydraulic fracturing formed part of a broader program to investigate fracture geometry and growth rates to confirm the characteristics of the hydraulic fractures placed. This monitoring showed that vertical stress in the conglomerate strata was being increased by up to 1 MPa in close proximity to the hydraulic fracture and had the effect of tending to promote asymmetrical growth of subsequent fractures about the injection borehole.Monitoring of stress changes in the overburden strata during longwall retreat was undertaken at two different locations at the mine. The monitoring indicated stress changes were evident 150 m ahead of the longwall face and abutment loading reached a maximum increase of about 7.5 MPa. The stresses ahead of mining change gradually with distance to the approaching longwall and in a direction consistent with the horizontal in situ stresses. There was no evidence in the stress change monitoring results to indicate significant cyclical forward abutment loading ahead of the face consistent with the observations of face conditions underground adjacent to both measurement locations. The forward abutment load determined from the stress change monitoring is consistent with the weight of overburden strata overhanging the goaf indicated by subsidence monitoring."

Jan 1, 2015

By Collin L. Stewart

The high cost and limited flexibility of modern longwall systems has resulted in the need for mine engineers and geologists to predict possible adverse mining areas ahead of mining and to then design and implement suitable ground control solutions in a timely and cost effective manner. Therefore, over the last 30 years, geo-technical evaluations for coal mine planning and development have advanced from a minor afterthought to an important part of today?s successful, high capacity, longwall mining operations. The latest iteration in this progression of improved analysis for predicting future mining conditions is a computer-based Stability Mapping System developed by West Virginia University. This system is designed to allow the mining engineer and geologist to effectively combine the mine geologic characteristics, stress influences, and structural features into an integrated stability map for use in mine planning and support design. This paper details the application of the stability mapping system to Bowie Resources, LLC, Bowie No. 3, multiple-seam longwall coal mine. At this mine, the prediction of adverse mining conditions using the stability mapping system allowed management to accurately adjust their support densities and operational procedures, and to successfully mine through difficult conditions safely and successfully.

Jan 1, 2006

By Sanjay Kumar Singh

This paper presents ground control technology associated with a continuous mining operation for mass exploitation of underground coal deposits in the Indian coal mining Industry It shows that competency of roof strata and performances of continuous miners are safer, than other coal mining method as well as productive and economical. Continuous miners keep playing a major role in the underground coal mining industry for their safety and as well as their productivity. Regarding past experiences in Indian coalfields, Chirimiri and Jhanjara mines have achieved exceptional performances, with a potential for over 500,000 tonnes per year. Tandsi mine has difficult roof conditions and does not typically achieve high production and productivity. Even so, the difficult roof conditions have been controlled with modern ?world best practice? roof bolting systems and an output of up to 1,200 tonnes per day has been achieved. It can further be emphasized that if this technology is implemented properly it will bring an unfathomable change to the Indian mining scenario. There are many mines in India that may have potential and economic viability with ground control technology concepts for installing continuous miner systems and beginning mass exploitation of underground coal deposits.

Jan 1, 2011

By Xingkai Wang, Wenbing Xie

"To control the large deformation of soft rock around the roadway subjected to high stress, it is important to improve the stability of support structure, in addition to increasing support strength. In this study, the causes for the destabilization of U-steel frame and its loading characteristics were analyzed by theoretical analysis, laboratory experiments and field tests. The technology of constant support resistance, the principle of support structure compensation and the compensation technique are proposed. The results indicated that the main reasons for frame structure destabilization are caused by low strength of connector, irrational structure of connector, poor interaction between the surrounding rocks and support frame and structure, and unstable support structure. Thus, the corresponding technological measures, such as connector with high strength and rational structure are adopted. The bearing capacity of frame is unstable after slipping. In order to maintain the high support resistance when the frame is performing the support function, the frame connector should be retightened after slipping. Though the working resistance may be improved greatly by using the backfilling or back grouting of U-steel, the frame remains unstable because of the unstable frame structure. Therefore, according to the deformation characteristics of rocks surrounding the roadway and the structure instability of U- steel frame, the stable structure device is used to carry out the structural compensation of U-steel frame, and the whole bearing capacity of the frame and its structural stability are improved greatly.INTRODUCTIONThroughout the development of the roadway supports for coal mines in China, it can be seen that the supporting strength and supporting resistance increase continuously with increase in mining depth and supporting difficulties [1]. With respect to the ground control mechanism and supporting technology of rocks surrounding the soft rock roadways subjected to high stress, considerable research has been done both at home and abroad. The backfilling technology behind the high-resistance and yieldable U-steel wall, the new type of grout/bolt support technology and the bolting with high-strength mesh support technology were developed, and have been used widely in coal mines with notable economic benefits [2-7]. However, a large number of engineering practices show that in many cases the existing rock control technology of roadway may not control the large deformation of the soft rock roadways subjected to high stress. The reason that the large deformation of soft rock roadway occurs is mainly due to poor structure stability of existing frame bearing structure, not insufficient support strength."

Jan 1, 2015

By Yajie Wang

Traditionally, roof falls are usually attributed to bad roof strata and high vertical stress related to the overburden depth. However, roof falls under shallow overburden depth are oflen caused by a high horizontal stress field. Recent studies have proven that the high horizontal stress field, if existing, plays a major role in roof stability. Also the roof conditions are related to the entry diredions under a horizontal stress field. Questions are: How to orient the entry to a favorable direction to prevent the roof falls? If the entry cannot be oriented, how to support it? Through a case study in mine A, this paper analyzes the horizontal stress effect on roof stability. The guideline for the entry orientation is given based on the results of analysis. Additionally, suggestions are made for those entries that cannot be oriented to a favorable direction.

Jan 1, 1998

By B. G. D. Smart

An understanding of the nature of yield zones surrounding coal mine excavations is fundamental to the design of mine support systems. Various methods have been designed for investigation of underground rock masses and an extensometric technique, the Magnetic Rod Extensometer, has been developed to overcome inherent design limitations in existing equipment of this type. This paper refers to the prototype form of the extensometer and details changes designed to overcome a variety of drawbacks indicated by routine use of the equipment. The principal change has been one of manual to computerised data acquisition and presentation in the laboratory phase of the system. This has dramatically reduced the time taken to process underground measurements and produce numerical and graphical results. The revised Magnetic Rod Extensometer represents an integrated instrumentation system that combines speed and accuracy in all areas of data handling.

Jan 1, 1984

By Karsten Zimmermann

The paper presents a study on the influence of face retreat rate in longwall coal mining on surface subsidence. It shows possibilities to influence dynamic ground movement by using a specific and controlled winning regime. For this, a dynamic stochastic prediction model used by DMT in Germany will be proved and adjusted on the specific character of geology in the Northern Appalachian coal field. Occurring ground movements such as inclination, curvature and deformation can be analyzed under static and dynamic points of view. It is theoretically shown that the face retreat rate has only a small influence on the static deformation values, but directly affects rate and acceleration of subsidence and deformation processes. The study shows that because of low mining depth and high mined thickness, static deformation values have the largest impact to surface objects. This implies that high face retreat rates don?t affect the impact on surface objects.

Jan 1, 2007

By David F. Gearhart, Khaled M. Mohamed

"Trusses are primarily used as passive roof supports in coal mines. They are constructed of three main parts: two grouted bolts installed at opposing forty-five degree angles into the roof so that they are anchored over the ribs and a cross member that ties the angled bolts together. There is also hardware used to assemble these components. The capacities of the angled bolts are typically 30 to 40 tons and the tensile capacity of the cross member is also 30 to 40 tons. Importantly, the direction of the immediate roof loading on the cross member is unlike the direction of the loading on the angled bolts. The load on the cross member is transverse to the longitudinal axis instead of along it, and therefore the cross member is loaded in the weakest direction.Previous tests conducted on truss systems applied loads such that the increasing tension in the two diagonal bolts increased the tension in the horizontal cross member, resulting in a stiff response. By contrast, if the load is applied directly to the cross member, which then transmits those forces to the diagonal bolts, it results in a much softer response.Based on this difference, laboratory tests to apply transverse loads and measure the vertical load capacity of three different types of cross members were conducted using the Mine Roof Simulator (MRS) located at the National Institute for Occupational Safety and Health (NIOSH) in Pittsburgh. The length of the samples was about 16 feet. Single-point load tests, with the load applied in the center of the specimen were conducted to verify the performance of the test arrangement and the finite element models. Double-point load tests, with a span of eight feet, were also conducted. This arrangement replicates the performance of the cross members with a distributed load. Both of these test arrangements were conducted on one-inch-diameter threaded steel bars and 0.7-inch-diameter cable and 0.6-inch-diameter cable cross members.For the single-point load configuration, the yield of the one-inch bar was nominally 22 kips of vertical load, achieved at 17 inches of deflection. For both sizes of the cable cross members, yield was not achieved even after 18 inches of deflection. Peak vertical loads were about 20 kips for the 0.7-inch cables and 15 kips for the 0.6- inch cables. For the double-point load configurations, the one-inch bar cross members yielded at 33 kips of vertical load and 10 inches of deflection. The 0.7-inch-diameter cable cross members broke strands at 30 kips of vertical load and 10 inches of closure, and the 0.6-inch-diameter cable cross members broke strands at 25 kips of vertical load and 10 inches of closure. Finite element models of each of the six different configurations were developed and show the variation of the vertical capacity of the cross members and the difference of the behavior of the bar versus the cables."

Jan 1, 2015

Previously, a variety of risk rating systems were used on different mines. However, these were mostly site specific and geology based systems. The purpose of developing a uniform rating system, to be used on all Anglo Coal open cast mines, is to provide an unbiased, standard and quantifiable assessment of the risk from highwall and lowwall failures. This takes into account relative differences in the importance of hazards, as experienced on each mine as a result of different combinations of geotechnical factors and mining conditions. The system is based on critical geotechnical and other parameters that have been identified by mining personnel and rock engineers. The primary advantage of this risk rating system is that all open cast mines in Anglo Coal use an almost identical system, which enables the user to compare their risk to the risk at neighbouring mines and/or other open cast mines. The system can be adjusted to meet local, mine specific requirements. The implementation of this new system (a computer program that automatically calculates the risk) has been made as practical and easy to use as possible. Therefore, this tool can be used by personnel from other mining disciplines not directly related to rock engineering.

Jan 1, 2004

By Z. T. Bieniawski

This paper presents the results of a survey of room and pillar dimensions and design practice in U.S. coal mines aimed at improving the design procedures in room and pillar mining. A review is given of the current pillar strength formulas and suggestions are made for better utilization of research results in engineering practice.

Jan 1, 1981

By John Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has collected pillar and span data at 34 stone mines in 10 states to develop pillar and roof span design guidelines for underground stone mines. Pillar, floor and roof conditions each contribute significantly to the overall mine stability. The roof may be stable for a century, or it may appear to be stable but fail with little warning. Clearly, an assessment of the mine roof is critical to the safety of these operations. However, up until now, the assessment of the mine roof came primarily from exposures in roof falls or portal areas. This provides only limited information, and a more proactive approach is needed to assess changing mine conditions. A separate effort was undertaken to examine the roof structure with the use of a borescope. Numerous physical and geologic roof structures were observed with a stratascope/borehole video camera. The objective of this work was to develop a technique of assigning numerical values to features seen within the mine roof and apply those values to formulate a roof stability evaluation. Such features as changes in color, grain size, and general lithologies are readily observed. Minor structures in the rock, fossils and fractures are also readily identified. Each feature may have a variable and site-specific impact on roof quality. A number of mines were visited and a series of holes were borescoped in each mine. The features identified in the roof were classified and potential for roof damage related to each feature was assessed. A process is presented that relates the structures and their locations to provide a numerical value, or roof quality index that can be used to assess roof stability.

Jan 1, 2009

By Jinsheng Chen

The major functions of longwall headgate entries are to provide access ways to the outby submains or mains for coal transportation and to the longwall face for fresh air and for transporting men and material during longwall operations. Any roof control problems such as cutter roofs or roof falls in the outby headgate entries could result in significant production delays to the longwall face and may be a threat to miners' safety Under a thinly laminated immediate roof and a high horizontal stress field, even a longwall headgate entry that has an angle of less than 45 degree to the maximum horizontal stress may experience roof deterioration in the outby headgate if the longwall panel mining sequence and retreat direction are not properly considered. This paper attempts to analyze the causes of the roof control problems experienced in the longwall gate entries at our Cumberland and Emerald mines in Pennsylvania and to determine the optimal longwall panel mining sequence and retreat direction for the future mining area at Cumberland

Jan 1, 1998

By Rafal Misa

In order to prevent the formation of mining damage or to reduce its reach, it is advisable to look for technical solutions which would enable effective protection of construction sites from the impacts of underground mining. So far, other authors have mainly focused on developing methods of securing construction sites in order to minimize the damage resulting from underground mining; the issue of geotechnical methods for protecting buildings against mining damage has not been thoroughly covered in those articles. It should be noted that there are relatively few publications directly related to this issue, nor are there practical examples of geotechnical protection. In this paper, a geotechnical solution available for securing building structures is discussed. Trenches presented in this research reduce the size and range of mining deformation. The results of numerical modelling for sample protective solutions, aimed at reducing the impact of mining activity on the terrain surface under various conditions, are presented. The calculations were performed with the aid of the Abaqus 6.10-2 software, based on the Finite Element Method.

Jan 1, 2014

By Takashi Sasaoka, Hiroshi Takamoto, Kikuo Matsui, Hideki Shimada

"Indonesia is the second largest coal exporter to Japan. Almost all the coal is produced from open cut mines. However, a great deal of coal is left in the highwalls of the mined-out pits. The use of highwall mining systems has increasingly come into play in the U.S. and Australia, when overburden depth exceeds economical recovery in an open cut mine. However, the stability of the highwalls is always a major safety concern in such mining. This paper describes the characteristics of the highwall mining system and discusses the appropriate highwall mining system for use in Indonesia.INTRODUCTIONIndonesia produces over 200 Mt of clean coal and is the second largest coal exporter to Japan, accounting for about 32 Mt of coal annually. Over 99% of the coal produced in Indonesia comes from surface mines. More open cut mines will be developed and more coal will be mined in order to fill the great demand both in Indonesia and the rest of the world.In open cut mines in Indonesia, there are many sites where mining operations have developed long highwalls that have been abandoned due to the current economics. Mining operations have been transferred to lower stripping ratio blocks of coal or overlying seams. In some cases, coal lies buried beneath spoil heaps or is covered with mud and water. It is estimated that there is a great deal of coal beneath abandoned and working highwalls. Considering these situations, it seems to be worth introducing highwall mining systems into Indonesian open cut mines.Final highwalls of open cut mines can form the starting point for other mining methods, such as highwall or underground mining. In its basic application, highwall mining is a technique utilized after an open cut portion of a reserve has been mined, sometimes prior to the introduction of underground mining (Seib, 1993). In this system, the coal seam is mined by remotely operated equipment, such as an auger machine or a modified continuous miner incorporated into a highwall mining system. The major problems with highwall mining systems are less coal recovery due to leaving coal as the pillars and the instability of openings and highwalls due to the pillar and roof failures."

Jan 1, 2010

By WenFeng Li

A 3D roof bolt model with the consideration of rebar, resin, bearing plate, and resin/rock interface was developed for studying the bolt/rock interactions of the tensioned and fully-grouted resin bolts. For the tensioned bolts, 2 ft compressive zone above the rooflineis generated by the 10 tons pretension. Since the free portion of the tensioned bolts displays a higher vertical stress, the increase of the bearing capacity of the rocks in such range is much larger. For the fully grouted resin bolts, despite no pretension is generated during installation, the roof sag can indirectly generate a compressive zone near the roof line. In addition, the analysis on the differences in bolt/rock interactions when employing the tensioned or fully-grouted resin bolts indicates that the fully-grouted resin bolts are preferred as the primary support when weak and thinly-bedded immediate-roof is present. Meanwhile, it is found that both the tensioned and fully-grouted resin bolts may have very limited effect in preventing and/or control the cutter roof.

Jan 1, 2014

By Houquan Zhang, Ming Li, Guimin Zhang, Bei Zhang

"The support quality of bolts in deep roadways is one of the important factors for efficient and safe coal production. A new kind of non-destructive testing technique and equipment was used to monitor the axial bolt load in real time in deep roadways. Based on the test results, the working status of bolt support in deep roadways was evaluated. The research results show that the variation characteristics of axial bolt load is consistent with the distribution characteristics of rock pressure no matter whether it is in the initial support stage or mining disturbance stage. The axial load of bolts located 20m outby the development face has an overall rising trend within 3-5 days after installation. Within a certain distance in the front abutment pressure zone in front of the face, the axial bolt load increases with the advance of coal extraction. When coal and rock in the abutment pressure zone yield, the axial bolt load is dropped correspondingly. This kind of non-destructive testing technique provides an advanced means of detection and evaluation on bolt support quality.INTRODUCTIONMany coal seams more than 800m deep are being mined in eastern China. Roadways of large cross-section are being developed in coal seams more than 600m deep in western China (Kang et al. 2014). Moreover, these roadways are commonly supported by roof bolts and have encountered many support problems, including soft rock strata, intense mining disturbance, and abnormal tectonic stress. The stability of its surrounding rocks is difficult to maintain, the roof bolt even fails before mining (Shen 2014; Jiang et al. 2015). Therefore, it is very important to develop an effective method to detect the bolt quality in real time and evaluate the bolt's safety status.During installation of roof bolt, the installation quality is heavily affected by installation equipment and tools, field conditions, and operators' skills (Li et al. 2005; Shan 2009). The anchorage length will be shorter than the designed one if the resin cartridges are pushed to the bottom of excessively long drill hole and stay there without being shredded and mixed. The support function of the bolt would be weakened by the shorter anchorage length."

Jan 1, 2016

By Shengliyang Yang, Jinghu Yang, Jiachen Wang, Xiaomeng Li

"Safe and efficient mining of extremely inclined thick coal seams less than 20m thick is one of the new challenges in China coal industry. In recent years, the extremely inclined thick coal seams have been encountered in some old mines and western China, and currently the top coal caving longwall mining method has been successfully applied to this kind of coal seams. Accordingly, this paper studies the roof movement and its impact on shield supports of top-coal caving longwall mining in extremely inclined thick coal seams. The structure of main roof before failure was simulated by the fix-ended beam, and provided the solutions for determination of maximum compressive stress of the bottom beam end and maximum tensile stress of the top beam end. The failure mode on the upper end of working face is mainly a combination of compression and shearing, while that for the bottom end is tension and shearing. Roof fracture begins at the upper end of working and propagates downward. The shape of collapsed roof strata can be described as parabolic and divided into three segments from top to bottom, including no filling, uneven filling and densely filling segments. The roof loading conditions of no filling segment is more likely to have dynamic burst impacts.INTRODUCTIONExtremely inclined thick coal seam refers to that the dip angle of coal seam is greater than 45° and the thickness is greater than 3.5m (Wang and Zhang, 2015a; Wang and Zhang, 2015b; Wang, 2005; Xie, Gao, and Shangguan, 2005; Wu, et al., 2014; Deng and Wang, 2014; He, et al., 2015). This type of coal seams can be divided into three categories: 1. The extremely inclined thick coal seam, of which the thickness is less than 5m and the dip angle is less than 60°, is usually mined by fully-mechanized longwall mining method. 2. The extremely inclined thick coal seam, of which the thickness is 5 m-20m, is usually mined by top coal caving longwall method. And 3. When the thickness of extremely inclined thick coal seam is greater than 20m, it is mined by the horizontal section top coal caving longwall method. For example, the average angle ofWudong coal mine in Xinjiang province is 45°, and the thickness is 27m. Wudong coal mine is applying the horizontal section top coal caving longwall mining, producing 3 million tons annually per working face (Figure 1)."

Jan 1, 2016